15 Revision History
Changes from December 4, 2024 to November 15, 2025 (from Revision (December 2024) to Revision A (November 2025))
- Remove note about device family.Go
- Update RAT.Go
- Update MCU R5F ATCM/BTCM address.Go
- Update
RTC Unsupported FeaturesGo
- Added
"Two digital voltage domains" in section RTC
Unsupported Features Go
- Added Content of Initialization
ChapterGo
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Add information about errata affecting operation
frequency.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Remove "_" from PADCONFIGx Register name.Go
- Update register names.Go
- AVS Class-0 not supported. Removed from list of
features.Go
- Update register names.Go
- Update register names.Go
- Update register names.Go
- Update register names.Go
- Update register names.Go
- Update register names.Go
- Update register names.Go
- Update register
names.Go
- Update register names.Go
- Update
MCU_CTRL_MMR_CFG0_MCU_PLL_CLKSEL Register
name.Go
- Update register nameGo
- Update register
names.Go
- Add Interrupt Controller section. Remove Time Sync
Support.Go
- I2C: Genericize I2C Module imageGo
- I2C: Updated note under I2C Block Diagram to clarify the i variablesGo
- I2C: Updated note in I2C Clocking to clarify the i variablesGo
- I2C: Updated subsection reference to parent of the subsection Go
- MCSPI: MCSPI Interface Signals in Controller Mode updated to a more generic imageGo
- MCSPI: Update MCSPI Channels to show as CH(i) instead of CHi.Go
- SPI: Basic MCSPI Pins for Peripheral Mode table and diagrams updated to be nire generic Go
- Add addition information to Polarity and Phase regarding data
transfer.Go
- SPI: Update Global Initialization of Surrounding Modues to mention not all modules are applicable Go
- Added RX, TX, CTS and RTS signals to main domain. Go
- UART: changed description in System Using RS-485 Communication to better align with UART instance used in section's imageGo
- UART: Changed IrDA Mode Interface Signals image and paragraph to be more genericGo
- UART: Made CIR Mode Interface Signals diagram and paragraph more genericGo
- Update DLL and DLH Hex values associated with 160MHz and 192MHz
Source Clock.Go
- CPSW: Update interface mode registers to more generic name. Go
- CPSW: Updated RMII clocking register to more generic nameGo
- CPSW: Updated CPSW CPTS CLKSEL to generic bit nameGo
- CPSW: Change to generic CPTS_CLKSEL nameGo
- CPSW: updated to generic names for ENET1_CTRL and ENET2_CTRLGo
- Fixed typo of SDIO version from 4.0 to 3.0.Go
- EPW: Updated instance counts and register names for Time-Base ClocksGo
- GTC: Updated CLKSEL register name Go
- RTC Chapter updated.Go
- Timers: Updated paragraph to clarify instance counts. Updated register reference to register name instead of register regionGo
- DCC: Update note and image to be genericGo
- Update Pad Configuration Register Functional Description
TableGo
- Mark ISO_OVR as Reserved.Go
- Add Drive Strength Control options.Go