SPRUJ79A November   2024  – December 2025 F29H850TU , F29H859TU-Q1

 

  1.   1
  2.   Read This First
    1.     About This Manual
    2.     Notational Conventions
    3.     Glossary
    4.     Related Documentation From Texas Instruments
    5.     Support Resources
    6.     Trademarks
  3.   ► C29x SYSTEM RESOURCES
    1.     Technical Reference Manual Overview
  4. 1 C29x Processor
    1. 1.1 CPU Architecture
      1. 1.1.1 C29x Related Collateral
    2. 1.2 Lock and Commit Registers
    3. 1.3 C29x CPU Registers
      1. 1.3.1 C29CPU Base Address Table
      2. 1.3.2 C29_RTINT_STACK Registers
      3. 1.3.3 C29_SECCALL_STACK Registers
      4. 1.3.4 C29_SECURE_REGS Registers
      5. 1.3.5 C29_DIAG_REGS Registers
      6. 1.3.6 C29_SELFTEST_REGS Registers
  5. 2 System Control and Interrupts
    1. 2.1  C29x System Control Introduction
    2. 2.2  System Control Functional Description
      1. 2.2.1 Device Identification
      2. 2.2.2 Device Configuration Registers
    3. 2.3  Resets
      1. 2.3.1 Reset Sources
      2. 2.3.2 External Reset (XRS)
      3. 2.3.3 Simulate External Reset
      4. 2.3.4 Power-On Reset (POR)
      5. 2.3.5 Debugger Reset (SYSRS)
      6. 2.3.6 Watchdog Reset (WDRS)
      7. 2.3.7 ESM NMI Watchdog Reset (NMIWDRS)
      8. 2.3.8 EtherCAT SubordinateDevice Controller (ESC) Module Reset Output
    4. 2.4  Interrupts
      1. 2.4.1 External Interrupts (XINT)
    5. 2.5  Safety Features
      1. 2.5.1 Write Protection on Registers
        1. 2.5.1.1 LOCK Protection on System Configuration Registers
        2. 2.5.1.2 EALLOW Protection
      2. 2.5.2 PIPE Vector Address Validity Check
      3. 2.5.3 NMIWDs
      4. 2.5.4 System Control Registers Parity Protection
      5. 2.5.5 ECC Enabled RAMs, Shared RAMs Protection
      6. 2.5.6 ECC Enabled Flash Memory
      7. 2.5.7 ERRORSTS Pin
    6. 2.6  Clocking
      1. 2.6.1 Clock Sources
        1. 2.6.1.1 Primary Internal Oscillator (INTOSC2)
        2. 2.6.1.2 Backup Internal Oscillator (INTOSC1)
        3. 2.6.1.3 External Oscillator (XTAL)
        4. 2.6.1.4 Auxiliary Clock Input (AUXCLKIN)
      2. 2.6.2 Derived Clocks
        1. 2.6.2.1 Oscillator Clock (OSCCLK)
        2. 2.6.2.2 System PLL Output Clock (PLLRAWCLK)
      3. 2.6.3 Device Clock Domains
        1. 2.6.3.1 System Clock (PLLSYSCLK)
        2. 2.6.3.2 CPU Clock (CPUCLK)
        3. 2.6.3.3 Peripheral Clock (PERx.SYSCLK)
        4. 2.6.3.4 MCAN Bit Clock
        5. 2.6.3.5 CPU Timer2 Clock (TIMER2CLK)
      4. 2.6.4 External Clock Output (XCLKOUT)
      5. 2.6.5 Clock Connectivity
      6. 2.6.6 Using an External Crystal or Resonator
        1. 2.6.6.1 X1/X2 Precondition Circuit
      7. 2.6.7 PLL
        1. 2.6.7.1 System Clock Setup
        2. 2.6.7.2 SYS PLL Bypass
      8. 2.6.8 Clock (OSCCLK) Failure Detection
        1. 2.6.8.1 Missing Clock Detection Logic
        2. 2.6.8.2 Dual Clock Comparator (DCC)
    7. 2.7  Bus Architecture
      1. 2.7.1 Safe Interconnect
        1. 2.7.1.1 Safe Interconnect for Read Operation
        2. 2.7.1.2 Safe Interconnect for Write Operation
      2. 2.7.2 Peripheral Access Configuration using FRAMESEL
      3. 2.7.3 Bus Arbitration
    8. 2.8  32-Bit CPU Timers 0/1/2
    9. 2.9  Watchdog Timers
      1. 2.9.1 Servicing the Watchdog Timer
      2. 2.9.2 Minimum Window Check
      3. 2.9.3 Watchdog Reset or Watchdog Interrupt Mode
      4. 2.9.4 Watchdog Operation in Low-Power Modes
      5. 2.9.5 Emulation Considerations
    10. 2.10 Low-Power Modes
      1. 2.10.1 IDLE
      2. 2.10.2 STANDBY
    11. 2.11 Memory Subsystem (MEMSS)
      1. 2.11.1 Introduction
      2. 2.11.2 Features
      3. 2.11.3 Configuration Bits
        1. 2.11.3.1 Memory Initialization
      4. 2.11.4 RAM
        1. 2.11.4.1  MEMSS Architecture
        2. 2.11.4.2  RAM Memory Controller Overview
        3. 2.11.4.3  Memory Controllers
          1. 2.11.4.3.1 128-Bit LPx and CPx Memory Controller
          2. 2.11.4.3.2 64-Bit LDx and CDx Memory Controller
          3. 2.11.4.3.3 M0 Memory Controller
        4. 2.11.4.4  RTDMA Burst Support
        5. 2.11.4.5  Atomic Memory Operations
        6. 2.11.4.6  RAM ECC
        7. 2.11.4.7  Read-Modify-Write Operations
        8. 2.11.4.8  Dataline Buffer
        9. 2.11.4.9  HSM Sync Bridge
        10. 2.11.4.10 Access Bridges
          1. 2.11.4.10.1 Debug Access Bridge
          2. 2.11.4.10.2 Global Access Bridge
          3. 2.11.4.10.3 Program Access Bridge
      5. 2.11.5 ROM
        1. 2.11.5.1 ROM Dataline Buffer
        2. 2.11.5.2 ROM Prefetch
      6. 2.11.6 Arbitration
      7. 2.11.7 Test Modes
      8. 2.11.8 Emulation Mode
    12. 2.12 System Control Register Configuration Restrictions
    13. 2.13 Software
      1. 2.13.1  SYSCTL Registers to Driverlib Functions
      2. 2.13.2  MEMSS Registers to Driverlib Functions
      3. 2.13.3  CPU Registers to Driverlib Functions
      4. 2.13.4  CPUTIMER Registers to Driverlib Functions
      5. 2.13.5  XINT Registers to Driverlib Functions
      6. 2.13.6  LPOST Registers to Driverlib Functions
      7. 2.13.7  SYSCTL Examples
        1. 2.13.7.1 Missing clock detection (MCD) - SINGLE_CORE
        2. 2.13.7.2 XCLKOUT (External Clock Output) Configuration - SINGLE_CORE
      8. 2.13.8  TIMER Examples
        1. 2.13.8.1 Timer Academy Lab - SINGLE_CORE
        2. 2.13.8.2 CPU Timers - SINGLE_CORE
        3. 2.13.8.3 CPU Timers - SINGLE_CORE
      9. 2.13.9  WATCHDOG Examples
        1. 2.13.9.1 Watchdog - SINGLE_CORE
      10. 2.13.10 LPM Examples
        1. 2.13.10.1 Low Power Modes: Device Idle Mode and Wakeup using GPIO - SINGLE_CORE
        2. 2.13.10.2 Low Power Modes: Device Idle Mode and Wakeup using Watchdog - SINGLE_CORE
        3. 2.13.10.3 Low Power Modes: Device Standby Mode and Wakeup using GPIO - SINGLE_CORE
        4. 2.13.10.4 Low Power Modes: Device Standby Mode and Wakeup using Watchdog - SINGLE_CORE
    14. 2.14 SYSCTRL Registers
      1. 2.14.1  SYSCTRL Base Address Table
      2. 2.14.2  DEV_CFG_REGS Registers
      3. 2.14.3  MEMSS_L_CONFIG_REGS Registers
      4. 2.14.4  MEMSS_C_CONFIG_REGS Registers
      5. 2.14.5  MEMSS_M_CONFIG_REGS Registers
      6. 2.14.6  MEMSS_MISCI_REGS Registers
      7. 2.14.7  SYNCBRIDGEMPU_REGS Registers
      8. 2.14.8  CPU_SYS_REGS Registers
      9. 2.14.9  CPU_PER_CFG_REGS Registers
      10. 2.14.10 WD_REGS Registers
      11. 2.14.11 CPUTIMER_REGS Registers
      12. 2.14.12 XINT_REGS Registers
  6. 3 ROM Code and Peripheral Booting
    1. 3.1 Introduction
      1. 3.1.1 ROM Related Collateral
    2. 3.2 Device Boot Sequence
    3. 3.3 Device Boot Modes
      1. 3.3.1 Default Boot Modes
      2. 3.3.2 Custom Boot Modes
    4. 3.4 Device Boot Configurations
      1. 3.4.1 Configuring Boot Mode Pins
      2. 3.4.2 Configuring Boot Mode Table Options
      3. 3.4.3 Boot Mode Example Use Cases
        1. 3.4.3.1 Zero Boot Mode Select Pins
        2. 3.4.3.2 One Boot Mode Select Pin
        3. 3.4.3.3 Three Boot Mode Select Pins
    5. 3.5 Device Boot Flow Diagrams
      1. 3.5.1 Device Boot Flow
      2. 3.5.2 CPU1 Boot Flow
      3. 3.5.3 Emulation Boot Flow
      4. 3.5.4 Standalone Boot Flow
    6. 3.6 Device Reset and Exception Handling
      1. 3.6.1 Reset Causes and Handling
      2. 3.6.2 Exceptions and Interrupts Handling
    7. 3.7 Boot ROM Description
      1. 3.7.1  Boot ROM Configuration Registers
        1. 3.7.1.1 MPOST and LPOST Configurations
      2. 3.7.2  Entry Points
      3. 3.7.3  Wait Points
      4. 3.7.4  Memory Maps
        1. 3.7.4.1 Boot ROM Memory-Maps
        2. 3.7.4.2 Reserved RAM Memory-Maps
      5. 3.7.5  BootROM SSU APRs
      6. 3.7.6  ROM Structure and Status Information
      7. 3.7.7  Boot Modes and Loaders
        1. 3.7.7.1 Boot Modes
          1. 3.7.7.1.1 Flash Boot
          2. 3.7.7.1.2 RAM Boot
          3. 3.7.7.1.3 Wait Boot
        2. 3.7.7.2 Bootloaders
          1. 3.7.7.2.1 SPI Boot Mode
          2. 3.7.7.2.2 I2C Boot Mode
          3. 3.7.7.2.3 Parallel Boot Mode
          4. 3.7.7.2.4 CAN Boot Mode
          5. 3.7.7.2.5 CAN-FD Boot Mode
          6. 3.7.7.2.6 UART Boot Mode
      8. 3.7.8  GPIO Assignments
      9. 3.7.9  HSM and C29x ROM Task Ownership and Interactions
        1. 3.7.9.1 Application Authentication by HSM
      10. 3.7.10 Boot Status Information
        1. 3.7.10.1 Booting Status
      11. 3.7.11 BootROM Timing
    8. 3.8 Software
      1. 3.8.1 BOOT Examples
  7. 4 Lockstep Compare Module (LCM)
    1. 4.1 Introduction
      1. 4.1.1 Features
      2. 4.1.2 Block Diagram
      3. 4.1.3 Lockstep Compare Modules
    2. 4.2 Enabling LCM Comparators
    3. 4.3 LCM Redundant Module Configuration
    4. 4.4 LCM Error Handling
    5. 4.5 Register Parity Error Protection
    6. 4.6 Functional Logic
      1. 4.6.1 Comparator Logic
      2. 4.6.2 Self-Test Logic
        1. 4.6.2.1 Match Test Mode
        2. 4.6.2.2 Mismatch Test Mode
      3. 4.6.3 Error Injection Tests
        1. 4.6.3.1 Comparator Error Force Test
        2. 4.6.3.2 Register Parity Error Test
    7. 4.7 Software
      1. 4.7.1 LCM Registers to Driverlib Functions
    8. 4.8 LCM Registers
      1. 4.8.1 LCM Base Address Table
      2. 4.8.2 LCM_REGS Registers
  8. 5 Peripheral Interrupt Priority and Expansion (PIPE)
    1. 5.1 Introduction
      1. 5.1.1 Features
      2. 5.1.2 Interrupt Concepts
      3. 5.1.3 PIPE Related Collateral
    2. 5.2 Interrupt Controller Architecture
      1. 5.2.1 Dynamic Priority Arbitration Block
      2. 5.2.2 Post Processing Block
      3. 5.2.3 Memory-Mapped Registers
    3. 5.3 Interrupt Propagation
    4. 5.4 Configuring Interrupts
      1. 5.4.1 Enabling and Disabling Interrupts
      2. 5.4.2 Prioritization
        1. 5.4.2.1 User-Configured Interrupt Priority
        2. 5.4.2.2 Index-Based Fixed Interrupt Priority
      3. 5.4.3 Interrupt Blocking
      4. 5.4.4 Nesting and Priority Grouping
      5. 5.4.5 Stack Protection
      6. 5.4.6 Context
      7. 5.4.7 Live Firmware Update (LFU) Vector Mapping
    5. 5.5 Safety and Security
      1. 5.5.1 Access Control
      2. 5.5.2 PIPE Errors
      3. 5.5.3 Register Data Integrity and Safety
      4. 5.5.4 Self-Test and Diagnostics
    6. 5.6 Software
      1. 5.6.1 PIPE Registers to Driverlib Functions
      2. 5.6.2 INTERRUPT Examples
        1. 5.6.2.1 RTINT vs INT Latency example - SINGLE_CORE
        2. 5.6.2.2 INT and RTINT Nesting Example - SINGLE_CORE
        3. 5.6.2.3 RTINT Nesting limit - SINGLE_CORE
    7. 5.7 PIPE Registers
      1. 5.7.1 PIPE Base Address Table
      2. 5.7.2 PIPE_REGS Registers
  9. 6  Error Aggregator
    1. 6.1 Introduction
    2. 6.2 Error Aggregator Modules
    3. 6.3 Error Propagation Path from Source to CPU
    4. 6.4 Error Aggregator Interface
      1. 6.4.1 Functional Description
    5. 6.5 Error Condition Handling User Guide
    6. 6.6 Error Type Information
    7. 6.7 Error Sources Information
    8. 6.8 Software
      1. 6.8.1 ERROR_AGGREGATOR Registers to Driverlib Functions
    9. 6.9 ERRORAGGREGATOR Registers
      1. 6.9.1 ERRORAGGREGATOR Base Address Table
      2. 6.9.2 HSM_ERROR_AGGREGATOR_CONFIG_REGS Registers
      3. 6.9.3 ERROR_AGGREGATOR_CONFIG_REGS Registers
  10. 7  Error Signaling Module (ESM_C29)
    1. 7.1 Introduction
      1. 7.1.1 Features
      2. 7.1.2 ESM Related Collateral
    2. 7.2 ESM Subsystem
      1. 7.2.1 System ESM
        1. 7.2.1.1 Error Pin Monitor Event
      2. 7.2.2 Safety Aggregator
        1. 7.2.2.1 EDC Controller Interface Description
        2. 7.2.2.2 Read Operation on EDC Controller
        3. 7.2.2.3 Write Operation on EDC Controller
        4. 7.2.2.4 Safety Aggregator Error Injection
      3. 7.2.3 ESM Subsystem Integration View
    3. 7.3 ESM Functional Description
      1. 7.3.1 Error Event Inputs
      2. 7.3.2 Error Interrupt Outputs
        1. 7.3.2.1 High-Priority Watchdog
        2. 7.3.2.2 Critical-Priority Interrupt Output
      3. 7.3.3 Error Pin Output (ERR_O/ERRORSTS)
        1. 7.3.3.1 Minimum Time Interval
        2. 7.3.3.2 PWM Mode
      4. 7.3.4 Reset Type Information for ESM Registers
      5. 7.3.5 Clock Stop
      6. 7.3.6 Commit/Lock for MMRs
      7. 7.3.7 Safety Protection for MMRs
      8. 7.3.8 Register Configuration Tieoffs
        1. 7.3.8.1 Group0 High-Priority Tieoff
        2. 7.3.8.2 High-Priority Watchdog Enable Tieoff
    4. 7.4 ESM Configuration Guide
    5. 7.5 Interrupt Condition Control and Handling
      1. 7.5.1 ESM Low-Priority Error Interrupt
      2. 7.5.2 ESM High-Priority Error Interrupt
      3. 7.5.3 Critical-Priority Error Interrupt
      4. 7.5.4 High-Priority Watchdog Interrupt
      5. 7.5.5 Safety Aggregator Interrupt Control and Handling
    6. 7.6 Software
      1. 7.6.1 ESM_CPU Registers to Driverlib Functions
      2. 7.6.2 ESM_SYS Registers to Driverlib Functions
      3. 7.6.3 ESM_SAFETY_AGGREGATOR Registers to Driverlib Functions
      4. 7.6.4 ESM Examples
        1. 7.6.4.1 ESM Multicore Example (CPU1,CPU3) - MULTI_CORE
        2. 7.6.4.2 ESM Multicore Example (CPU1,CPU3) - MULTI_CORE
        3. 7.6.4.3 ESM - SINGLE_CORE
        4. 7.6.4.4 ESM - SINGLE_CORE
    7. 7.7 ESM Registers
      1. 7.7.1 ESM Base Address Table
      2. 7.7.2 ESM_CPU_REGS Registers
      3. 7.7.3 ESM_SYSTEM_REGS Registers
      4. 7.7.4 ESM_SAFETYAGG_REGS Registers
      5. 7.7.5 EDC_REGS Registers
  11. 8 Flash Module
    1. 8.1 Introduction to Flash Memory
      1. 8.1.1 FLASH Related Collateral
      2. 8.1.2 Features
      3. 8.1.3 Flash Tools
      4. 8.1.4 Block Diagram
    2. 8.2 Flash Subsystem Overview
    3. 8.3 Flash Banks and Pumps
    4. 8.4 Flash Read Interfaces
      1. 8.4.1 Bank Modes and Swapping
      2. 8.4.2 Flash Wait States
      3. 8.4.3 Buffer and Cache Mechanisms
        1. 8.4.3.1 Prefetch Mechanism and Block Cache
        2. 8.4.3.2 Data Line Buffer
        3. 8.4.3.3 Sequential Data Pre-read Mode
      4. 8.4.4 Flash Read Arbitration
      5. 8.4.5 Error Correction Code (ECC) Protection
      6. 8.4.6 Procedure to Change Flash Read Interface Registers
    5. 8.5 Flash Erase and Program
      1. 8.5.1 Flash Semaphore and Update Protection
      2. 8.5.2 Erase
      3. 8.5.3 Program
    6. 8.6 Read-While-Write Constraints
    7. 8.7 Migrating an Application from RAM to Flash
    8. 8.8 Flash Registers
      1. 8.8.1 FLASH Base Address Table
      2. 8.8.2 FLASH_CMD_REGS_FLC1 Registers
      3. 8.8.3 FLASH_CMD_REGS_FLC2 Registers
      4. 8.8.4 FRI_CTRL_REGS Registers
  12. 9 Safety and Security Unit (SSU)
    1. 9.1  Introduction
      1. 9.1.1 SSU Related Collateral
      2. 9.1.2 Block Diagram
      3. 9.1.3 System SSU Configuration Example
    2. 9.2  Access Protection Ranges
      1. 9.2.1 Access Protection Inheritance
    3. 9.3  LINKs
    4. 9.4  STACKs
    5. 9.5  ZONEs
    6. 9.6  SSU-CPU Interface
      1. 9.6.1 SSU Operation in Lockstep Mode
    7. 9.7  SSU Operation Modes
    8. 9.8  Security Configuration and Flash Management
      1. 9.8.1 BANKMGMT Sectors
      2. 9.8.2 SECCFG Sectors
      3. 9.8.3 SECCFG Sector Address Mapping
      4. 9.8.4 SECCFG Sector Memory Map
      5. 9.8.5 SECCFG CRC
    9. 9.9  Flash Write/Erase Access Control
      1. 9.9.1 Permanent Flash Lock (Write/Erase Protection)
      2. 9.9.2 Updating Flash MAIN Sectors
      3. 9.9.3 Firmware-Over-The-Air Updates (FOTA)
      4. 9.9.4 Updating Flash SECCFG Sectors
      5. 9.9.5 Reading Flash SECCFG Sectors
    10. 9.10 RAMOPEN Feature
    11. 9.11 Booting of CPU2 and CPU3
    12. 9.12 Debug Authorization
      1. 9.12.1 Global CPU Debug Enable
      2. 9.12.2 ZONE Debug
      3. 9.12.3 Authentication for Debug Access
        1. 9.12.3.1 Password-based Authentication
        2. 9.12.3.2 CPU-based Authentication
    13. 9.13 Hardcoded Protections
    14. 9.14 SSU Register Access Permissions
      1. 9.14.1 Permissions for SSU General Control Registers
      2. 9.14.2 Permissions for SSU CPU1 Configuration Registers
      3. 9.14.3 Permissions for SSU CPU2+ Configuration Registers
      4. 9.14.4 Permissions for CPU1 Access Protection Registers
      5. 9.14.5 Permissions for CPU2+ Access Protection Registers
    15. 9.15 SSU Fault Signals
    16. 9.16 Software
      1. 9.16.1 SSU Registers to Driverlib Functions
    17. 9.17 SSU Registers
      1. 9.17.1 SSU Base Address Table
      2. 9.17.2 SSU_GEN_REGS Registers
      3. 9.17.3 SSU_CPU1_CFG_REGS Registers
      4. 9.17.4 SSU_CPU2_CFG_REGS Registers
      5. 9.17.5 SSU_CPU3_CFG_REGS Registers
      6. 9.17.6 SSU_CPU1_AP_REGS Registers
      7. 9.17.7 SSU_CPU2_AP_REGS Registers
      8. 9.17.8 SSU_CPU3_AP_REGS Registers
    18. 9.18 C29DEBUGSS Registers
      1. 9.18.1 C29DEBUGSS Base Address Table
      2. 9.18.2 SECAP_HANDLER_REGS Registers
  13. 10Configurable Logic Block (CLB)
    1. 10.1  Introduction
      1. 10.1.1 CLB Related Collateral
    2. 10.2  Description
      1. 10.2.1 CLB Clock
    3. 10.3  CLB Input/Output Connection
      1. 10.3.1 Overview
      2. 10.3.2 CLB Input Selection
      3. 10.3.3 CLB Output Selection
      4. 10.3.4 CLB Output Signal Multiplexer
    4. 10.4  CLB Tile
      1. 10.4.1 Static Switch Block
      2. 10.4.2 Counter Block
        1. 10.4.2.1 Counter Description
        2. 10.4.2.2 Counter Operation
        3. 10.4.2.3 Serializer Mode
        4. 10.4.2.4 Linear Feedback Shift Register (LFSR) Mode
      3. 10.4.3 FSM Block
      4. 10.4.4 LUT4 Block
      5. 10.4.5 Output LUT Block
      6. 10.4.6 Asynchronous Output Conditioning (AOC) Block
      7. 10.4.7 High Level Controller (HLC)
        1. 10.4.7.1 High Level Controller Events
        2. 10.4.7.2 High Level Controller Instructions
        3. 10.4.7.3 <Src> and <Dest>
        4. 10.4.7.4 Operation of the PUSH and PULL Instructions (Overflow and Underflow Detection)
    5. 10.5  CPU Interface
      1. 10.5.1 Register Description
      2. 10.5.2 Non-Memory Mapped Registers
    6. 10.6  RTDMA Access
    7. 10.7  CLB Data Export Through SPI RX Buffer
    8. 10.8  CLB Pipeline Mode
    9. 10.9  Software
      1. 10.9.1 CLB Registers to Driverlib Functions
      2. 10.9.2 CLB Examples
        1. 10.9.2.1 CLB Example Lab - SINGLE_CORE
        2. 10.9.2.2 CLB eCAP Example Lab - SINGLE_CORE
        3. 10.9.2.3 CLB Combinational Logic - SINGLE_CORE
        4. 10.9.2.4 CLB GPIO Input Filter - SINGLE_CORE
        5. 10.9.2.5 CLB Auxilary PWM - SINGLE_CORE
        6. 10.9.2.6 CLB PWM Protection - SINGLE_CORE
    10. 10.10 CLB Registers
      1. 10.10.1 CLB Base Address Table
      2. 10.10.2 CLB_LOGIC_CONFIG_REGS Registers
      3. 10.10.3 CLB_LOGIC_CONTROL_REGS Registers
      4. 10.10.4 CLB_DATA_EXCHANGE_REGS Registers
  14. 11Dual-Clock Comparator (DCC)
    1. 11.1 Introduction
      1. 11.1.1 Features
      2. 11.1.2 Block Diagram
    2. 11.2 Module Operation
      1. 11.2.1 Configuring DCC Counters
      2. 11.2.2 Single-Shot Measurement Mode
      3. 11.2.3 Continuous Monitoring Mode
      4. 11.2.4 Error Conditions
    3. 11.3 Interrupts
    4. 11.4 Software
      1. 11.4.1 DCC Registers to Driverlib Functions
      2. 11.4.2 DCC Examples
        1. 11.4.2.1 DCC Single shot Clock verification - SINGLE_CORE
        2. 11.4.2.2 DCC Single shot Clock measurement - SINGLE_CORE
        3. 11.4.2.3 DCC Continuous clock monitoring - SINGLE_CORE
    5. 11.5 DCC Registers
      1. 11.5.1 DCC Base Address Table
      2. 11.5.2 DCC_REGS Registers
  15. 12Real-Time Direct Memory Access (RTDMA)
    1. 12.1  Introduction
      1. 12.1.1 Features
      2. 12.1.2 RTDMA Related Collateral
      3. 12.1.3 Block Diagram
    2. 12.2  RTDMA Trigger Source Options
    3. 12.3  RTDMA Bus
    4. 12.4  Address Pointer and Transfer Control
    5. 12.5  Pipeline Timing and Throughput
    6. 12.6  Channel Priority
      1. 12.6.1 Round-Robin Mode
      2. 12.6.2 Software Configurable Priority of Channels
    7. 12.7  Overrun Detection Feature
    8. 12.8  Burst Mode
    9. 12.9  Safety and Security
      1. 12.9.1 Safety
        1. 12.9.1.1 Lockstep Mode
        2. 12.9.1.2 Memory Protection Unit (MPU)
          1. 12.9.1.2.1 MPU Errors
      2. 12.9.2 Security
      3. 12.9.3 RTDMA Errors
      4. 12.9.4 Self-Test and Diagnostics
    10. 12.10 Software
      1. 12.10.1 RTDMA Registers to Driverlib Functions
      2. 12.10.2 RTDMA Examples
        1. 12.10.2.1 RTDMA Academy Lab - SINGLE_CORE
        2. 12.10.2.2 RTDMA Transfer - SINGLE_CORE
        3. 12.10.2.3 RTDMA Transfer with MPU - SINGLE_CORE
        4. 12.10.2.4 RTDMA - MULTI_CORE
        5. 12.10.2.5 RTDMA Example - MULTI_CORE
        6. 12.10.2.6 RTDMA example with Resource Allocator - MULTI_CORE
        7. 12.10.2.7 RTDMA example with Resource Allocator - MULTI_CORE
    11. 12.11 RTDMA Registers
      1. 12.11.1 RTDMA Base Address Table
      2. 12.11.2 RTDMA_REGS Registers
      3. 12.11.3 RTDMA_DIAG_REGS Registers
      4. 12.11.4 RTDMA_SELFTEST_REGS Registers
      5. 12.11.5 RTDMA_MPU_REGS Registers
      6. 12.11.6 RTDMA_CH_REGS Registers
  16. 13External Memory Interface (EMIF)
    1. 13.1 Introduction
      1. 13.1.1 Purpose of the Peripheral
      2. 13.1.2 Features
        1. 13.1.2.1 Asynchronous Memory Support
        2. 13.1.2.2 Synchronous DRAM Memory Support
      3. 13.1.3 Functional Block Diagram
      4. 13.1.4 Configuring Device Pins
    2. 13.2 EMIF Module Architecture
      1. 13.2.1  EMIF Clock Control
      2. 13.2.2  EMIF Requests
      3. 13.2.3  EMIF Signal Descriptions
      4. 13.2.4  EMIF Signal Multiplexing Control
      5. 13.2.5  SDRAM Controller and Interface
        1. 13.2.5.1  SDRAM Commands
        2. 13.2.5.2  Interfacing to SDRAM
        3. 13.2.5.3  SDRAM Configuration Registers
        4. 13.2.5.4  SDRAM Auto-Initialization Sequence
        5. 13.2.5.5  SDRAM Configuration Procedure
        6. 13.2.5.6  EMIF Refresh Controller
          1. 13.2.5.6.1 Determining the Appropriate Value for the RR Field
        7. 13.2.5.7  Self-Refresh Mode
        8. 13.2.5.8  Power-Down Mode
        9. 13.2.5.9  SDRAM Read Operation
        10. 13.2.5.10 SDRAM Write Operations
        11. 13.2.5.11 Mapping from Logical Address to EMIF Pins
      6. 13.2.6  Asynchronous Controller and Interface
        1. 13.2.6.1 Interfacing to Asynchronous Memory
        2. 13.2.6.2 Accessing Larger Asynchronous Memories
        3. 13.2.6.3 Configuring EMIF for Asynchronous Accesses
        4. 13.2.6.4 Read and Write Operations in Normal Mode
          1. 13.2.6.4.1 Asynchronous Read Operations (Normal Mode)
          2. 13.2.6.4.2 Asynchronous Write Operations (Normal Mode)
        5. 13.2.6.5 Read and Write Operation in Select Strobe Mode
          1. 13.2.6.5.1 Asynchronous Read Operations (Select Strobe Mode)
          2. 13.2.6.5.2 Asynchronous Write Operations (Select Strobe Mode)
        6. 13.2.6.6 Extended Wait Mode and the EM1WAIT Pin
      7. 13.2.7  Data Bus Parking
      8. 13.2.8  Reset and Initialization Considerations
      9. 13.2.9  Interrupt Support
        1. 13.2.9.1 Interrupt Events
      10. 13.2.10 RTDMA Event Support
      11. 13.2.11 EMIF Signal Multiplexing
      12. 13.2.12 Memory Map
      13. 13.2.13 Priority and Arbitration
      14. 13.2.14 System Considerations
        1. 13.2.14.1 Asynchronous Request Times
      15. 13.2.15 Power Management
        1. 13.2.15.1 Power Management Using Self-Refresh Mode
        2. 13.2.15.2 Power Management Using Power Down Mode
      16. 13.2.16 Emulation Considerations
    3. 13.3 EMIF Subsystem (EMIFSS)
      1. 13.3.1 Burst Support
      2. 13.3.2 EMIFSS Performance Improvement
      3. 13.3.3 Buffer Module
        1. 13.3.3.1 CPU Write FIFO
      4. 13.3.4 Emulation Mode
    4. 13.4 Example Configuration
      1. 13.4.1 Hardware Interface
      2. 13.4.2 Software Configuration
        1. 13.4.2.1 Configuring the SDRAM Interface
          1. 13.4.2.1.1 PLL Programming for EMIF to K4S641632H-TC(L)70 Interface
          2. 13.4.2.1.2 SDRAM Timing Register (SDRAM_TR) Settings for EMIF to K4S641632H-TC(L)70 Interface
          3. 13.4.2.1.3 SDRAM Self Refresh Exit Timing Register (SDR_EXT_TMNG) Settings for EMIF to K4S641632H-TC(L)70 Interface
          4. 13.4.2.1.4 SDRAM Refresh Control Register (SDRAM_RCR) Settings for EMIF to K4S641632H-TC(L)70 Interface
          5. 13.4.2.1.5 SDRAM Configuration Register (SDRAM_CR) Settings for EMIF to K4S641632H-TC(L)70 Interface
        2. 13.4.2.2 Configuring the Flash Interface
          1. 13.4.2.2.1 Asynchronous 1 Configuration Register (ASYNC_CS2_CFG) Settings for EMIF to LH28F800BJE-PTTL90 Interface
    5. 13.5 Software
      1. 13.5.1 EMIF Registers to Driverlib Functions
      2. 13.5.2 EMIF Examples
    6. 13.6 EMIF Registers
      1. 13.6.1 EMIF Base Address Table
      2. 13.6.2 EMIF_REGS Registers
  17. 14General-Purpose Input/Output (GPIO)
    1. 14.1  Introduction
      1. 14.1.1 GPIO Related Collateral
    2. 14.2  Configuration Overview
    3. 14.3  Digital Inputs on ADC Pins (AIOs)
    4. 14.4  Digital Inputs and Outputs on ADC Pins (AGPIOs)
    5. 14.5  Digital General-Purpose I/O Control
    6. 14.6  Input Qualification
      1. 14.6.1 No Synchronization (Asynchronous Input)
      2. 14.6.2 Synchronization to SYSCLKOUT Only
      3. 14.6.3 Qualification Using a Sampling Window
    7. 14.7  PMBUS and I2C Signals
    8. 14.8  GPIO and Peripheral Muxing
      1. 14.8.1 GPIO Muxing
      2. 14.8.2 Peripheral Muxing
    9. 14.9  Internal Pullup Configuration Requirements
    10. 14.10 Open-Drain Configuration Requirements
    11. 14.11 Software
      1. 14.11.1 GPIO Registers to Driverlib Functions
      2. 14.11.2 GPIO Examples
        1. 14.11.2.1 Device GPIO Toggle - SINGLE_CORE
        2. 14.11.2.2 XINT/XBAR example - SINGLE_CORE
        3. 14.11.2.3 External Interrupt (XINT) - SINGLE_CORE
      3. 14.11.3 LED Examples
        1. 14.11.3.1 LED Blinky Example - MULTI_CORE
        2. 14.11.3.2 LED Blinky Example (CPU1,CPU3) - MULTI_CORE
        3. 14.11.3.3 LED Blinky example - SINGLE_CORE
        4. 14.11.3.4 LED Blinky Example (CPU1|CPU2|CPU3) - MULTI_CORE
        5. 14.11.3.5 LED Blinky Example (CPU2) - MULTI_CORE
        6. 14.11.3.6 LED Blinky Example (CPU3) - MULTI_CORE
        7. 14.11.3.7 LED Blinky Example - MULTI_CORE
        8. 14.11.3.8 LED Blinky Example (CPU1,CPU3) - MULTI_CORE
    12. 14.12 GPIO Registers
      1. 14.12.1 GPIO Base Address Table
      2. 14.12.2 GPIO_CTRL_REGS Registers
      3. 14.12.3 GPIO_DATA_REGS Registers
      4. 14.12.4 GPIO_DATA_READ_REGS Registers
  18. 15Interprocessor Communication (IPC)
    1. 15.1 Introduction
    2. 15.2 IPC Flags and Interrupts
    3. 15.3 IPC Command Registers
    4. 15.4 Free-Running Counter
    5. 15.5 IPC Communication Protocol
    6. 15.6 Software
      1. 15.6.1 IPC Registers to Driverlib Functions
      2. 15.6.2 IPC Examples
        1. 15.6.2.1 IPC basic message passing example with interrupt - MULTI_CORE
        2. 15.6.2.2 IPC basic message passing example with interrupt - MULTI_CORE
        3. 15.6.2.3 IPC basic message passing example with interrupt - MULTI_CORE
        4. 15.6.2.4 IPC basic message passing example with interrupt - MULTI_CORE
        5. 15.6.2.5 IPC basic message passing example with interrupt - MULTI_CORE
        6. 15.6.2.6 IPC basic message passing example with interrupt - MULTI_CORE
    7. 15.7 IPC Registers
      1. 15.7.1 IPC Base Address Table
      2. 15.7.2 IPC_COUNTER_REGS Registers
      3. 15.7.3 CPU1_IPC_SEND_REGS Registers
      4. 15.7.4 CPU2_IPC_SEND_REGS Registers
      5. 15.7.5 CPU3_IPC_SEND_REGS Registers
      6. 15.7.6 CPU1_IPC_RCV_REGS Registers
      7. 15.7.7 CPU2_IPC_RCV_REGS Registers
      8. 15.7.8 CPU3_IPC_RCV_REGS Registers
  19. 16Embedded Real-time Analysis and Diagnostic (ERAD)
    1. 16.1 Introduction
    2. 16.2 Enhanced Bus Comparator Unit
      1. 16.2.1 Enhanced Bus Comparator Unit Operations
      2. 16.2.2 Stack Qualification
      3. 16.2.3 Event Masking and Exporting
    3. 16.3 System Event Counter Unit
      1. 16.3.1 System Event Counter Modes
        1. 16.3.1.1 Counting Active Levels Versus Edges
        2. 16.3.1.2 Max and Min Mode
        3. 16.3.1.3 Cumulative Mode
        4. 16.3.1.4 Input Signal Selection
      2. 16.3.2 Reset on Event
      3. 16.3.3 Operation Conditions
    4. 16.4 Program Counter Trace
      1. 16.4.1 Built-in CCS™ Trace
      2. 16.4.2 Functional Block Diagram
      3. 16.4.3 Trace Qualification Modes
        1. 16.4.3.1 Trace Input Signal Conditioning
      4. 16.4.4 Trace Memory
      5. 16.4.5 PC Trace Software Operation
      6. 16.4.6 Trace Operation in Debug Mode
    5. 16.5 ERAD Ownership, Initialization, and Reset
      1. 16.5.1 Feature Level Ownership
      2. 16.5.2 Feature Access Security Mechanism
      3. 16.5.3 PC Trace Access Security Mechanism
    6. 16.6 ERAD Programming Sequence
      1. 16.6.1 Hardware Breakpoint and Hardware Watch Point Programming Sequence
      2. 16.6.2 Timer and Counter Programming Sequence
    7. 16.7 Software
      1. 16.7.1 ERAD Registers to Driverlib Functions
  20. 17Data Logger and Trace (DLT)
    1. 17.1 Introduction
      1. 17.1.1 Features
      2. 17.1.2 DLT Related Collateral
      3. 17.1.3 Interfaces
        1. 17.1.3.1 Block Diagram
    2. 17.2 Functional Overview
      1. 17.2.1 DLT Configuration
        1. 17.2.1.1 LINK Filter
        2. 17.2.1.2 TAG Filter
        3. 17.2.1.3 ERAD Event Trigger
        4. 17.2.1.4 Concurrent FILTERING modes
      2. 17.2.2 Time-stamping
      3. 17.2.3 FIFO Construction
        1. 17.2.3.1 FIFO Interrupt
    3. 17.3 Software
      1. 17.3.1 DLT Registers to Driverlib Functions
      2. 17.3.2 DLT Examples
        1. 17.3.2.1 DLT TAG filter example - SINGLE_CORE
        2. 17.3.2.2 DLT TAG filter example - SINGLE_CORE
        3. 17.3.2.3 DLT ERAD filter example - SINGLE_CORE
    4. 17.4 DLT Registers
      1. 17.4.1 DLT Base Address Table
      2. 17.4.2 DLT_CORE_REGS Registers
      3. 17.4.3 DLT_FIFO_REGS Registers
  21. 18Waveform Analyzer Diagnostic (WADI)
    1. 18.1 WADI Overview
      1. 18.1.1 Features
      2. 18.1.2 WADI Related Collateral
      3. 18.1.3 Block Diagram
      4. 18.1.4 Description
    2. 18.2 Signal and Trigger Input Configuration
      1. 18.2.1 SIG1 and SIG2 Configuration
      2. 18.2.2 Trigger 1 and Trigger 2
    3. 18.3 WADI Block
      1. 18.3.1 Overview
      2. 18.3.2 Counters
      3. 18.3.3 Pulse Width
        1. 18.3.3.1 Pulse Width Single Measurement
        2. 18.3.3.2 Pulse Width Aggregation
        3. 18.3.3.3 Pulse Width Average and Peak
      4. 18.3.4 Edge Count
        1. 18.3.4.1 Edge Count with Fixed Window
        2. 18.3.4.2 Edge Count with Moving Window
      5. 18.3.5 Signal1 to Signal2 Comparison
      6. 18.3.6 Dead Band and Phase
      7. 18.3.7 Simultaneous Measurement
    4. 18.4 Safe State Sequencer (SSS)
      1. 18.4.1 SSS Configuration
    5. 18.5 Lock and Commit Registers
    6. 18.6 Interrupt and Error Handling
    7. 18.7 RTDMA Interfaces
      1. 18.7.1 RTDMA Trigger
    8. 18.8 Software
      1. 18.8.1 WADI Registers to Driverlib Functions
      2. 18.8.2 WADI Examples
        1. 18.8.2.1 WADI Pulse Width Measurement - SINGLE_CORE
        2. 18.8.2.2 WADI Frequency Measurement - SINGLE_CORE
        3. 18.8.2.3 WADI Phase Overlap Measurement - SINGLE_CORE
        4. 18.8.2.4 WADI Deadband Measurement - SINGLE_CORE
        5. 18.8.2.5 WADI Frequency Measurement with SSS - SINGLE_CORE
        6. 18.8.2.6 WADI Pulse Wdith Check with DMA trigger - SINGLE_CORE
    9. 18.9 WADI Registers
      1. 18.9.1 WADI Base Address Table
      2. 18.9.2 WADI_CONFIG_REGS Registers
      3. 18.9.3 WADI_OPER_SSS_REGS Registers
  22. 19Crossbar (X-BAR)
    1. 19.1 X-BAR Related Collateral
    2. 19.2 Input X-BAR, ICL XBAR, MINDB XBAR
      1. 19.2.1 ICL and MINDB X-BAR
    3. 19.3 ePWM , CLB, and GPIO Output X-BAR
      1. 19.3.1 ePWM X-BAR
        1. 19.3.1.1 ePWM X-BAR Architecture
      2. 19.3.2 CLB X-BAR
        1. 19.3.2.1 CLB X-BAR Architecture
      3. 19.3.3 GPIO Output X-BAR
        1. 19.3.3.1 GPIO Output X-BAR Architecture
      4. 19.3.4 X-BAR Flags
    4. 19.4 Software
      1. 19.4.1 INPUT_XBAR Registers to Driverlib Functions
      2. 19.4.2 EPWM_XBAR Registers to Driverlib Functions
      3. 19.4.3 CLB_XBAR Registers to Driverlib Functions
      4. 19.4.4 OUTPUT_XBAR Registers to Driverlib Functions
      5. 19.4.5 MDL_XBAR Registers to Driverlib Functions
      6. 19.4.6 ICL_XBAR Registers to Driverlib Functions
      7. 19.4.7 XBAR Registers to Driverlib Functions
      8. 19.4.8 XBAR Examples
        1. 19.4.8.1 Input XBAR to Output XBAR Connection - SINGLE_CORE
        2. 19.4.8.2 Output XBAR Pulse Stretch - SINGLE_CORE
    5. 19.5 XBAR Registers
      1. 19.5.1 XBAR Base Address Table
      2. 19.5.2 INPUT_XBAR_REGS Registers
      3. 19.5.3 EPWM_XBAR_REGS Registers
      4. 19.5.4 CLB_XBAR_REGS Registers
      5. 19.5.5 OUTPUTXBAR_REGS Registers
      6. 19.5.6 MDL_XBAR_REGS Registers
      7. 19.5.7 ICL_XBAR_REGS Registers
      8. 19.5.8 OUTPUTXBAR_FLAG_REGS Registers
      9. 19.5.9 XBAR_REGS Registers
  23. 20Embedded Pattern Generator (EPG)
    1. 20.1 Introduction
      1. 20.1.1 Features
      2. 20.1.2 EPG Block Diagram
      3. 20.1.3 EPG Related Collateral
    2. 20.2 Clock Generator Modules
      1. 20.2.1 DCLK (50% duty cycle clock)
      2. 20.2.2 Clock Stop
    3. 20.3 Signal Generator Module
    4. 20.4 EPG Peripheral Signal Mux Selection
    5. 20.5 Application Software Notes
    6. 20.6 EPG Example Use Cases
      1. 20.6.1 EPG Example: Synchronous Clocks with Offset
        1. 20.6.1.1 Synchronous Clocks with Offset Register Configuration
      2. 20.6.2 EPG Example: Serial Data Bit Stream (LSB first)
        1. 20.6.2.1 Serial Data Bit Stream (LSB first) Register Configuration
      3. 20.6.3 EPG Example: Serial Data Bit Stream (MSB first)
        1. 20.6.3.1 Serial Data Bit Stream (MSB first) Register Configuration
      4. 20.6.4 EPG Example: Clock and Data Pair
        1. 20.6.4.1 Clock and Data Pair Register Configuration
      5. 20.6.5 EPG Example: Clock and Skewed Data Pair
        1. 20.6.5.1 Clock and Skewed Data Pair Register Configuration
      6. 20.6.6 EPG Example: Capturing Serial Data with a Known Baud Rate
        1. 20.6.6.1 Capturing Serial Data with a Known Baud Rate Register Configuration
    7. 20.7 EPG Interrupt
    8. 20.8 Software
      1. 20.8.1 EPG Registers to Driverlib Functions
      2. 20.8.2 EPG Examples
        1. 20.8.2.1 EPG Generating Synchronous Clocks - SINGLE_CORE
        2. 20.8.2.2 EPG Generating Two Offset Clocks - SINGLE_CORE
        3. 20.8.2.3 EPG Generating Two Offset Clocks With SIGGEN - SINGLE_CORE
        4. 20.8.2.4 EPG Generate Serial Data - SINGLE_CORE
        5. 20.8.2.5 EPG Generate Serial Data Shift Mode - SINGLE_CORE
    9. 20.9 EPG Registers
      1. 20.9.1 EPG Base Address Table
      2. 20.9.2 EPG_REGS Registers
      3. 20.9.3 EPG_MUX_REGS Registers
  24.   ► ANALOG PERIPHERALS
    1.     Technical Reference Manual Overview
  25. 21Analog Subsystem
    1. 21.1 Introduction
      1. 21.1.1 Features
      2. 21.1.2 Block Diagram
    2. 21.2 Optimizing Power-Up Time
    3. 21.3 Digital Inputs on ADC Pins (AIOs)
    4. 21.4 Digital Inputs and Outputs on ADC Pins (AGPIOs)
    5. 21.5 Analog Pins and Internal Connections
    6. 21.6 Software
      1. 21.6.1 ASYSCTL Registers to Driverlib Functions
    7. 21.7 Lock Registers
    8. 21.8 ASBSYS Registers
      1. 21.8.1 ASBSYS Base Address Table
      2. 21.8.2 ANALOG_SUBSYS_REGS Registers
  26. 22Analog-to-Digital Converter (ADC)
    1. 22.1  Introduction
      1. 22.1.1 Features
      2. 22.1.2 ADC Related Collateral
      3. 22.1.3 Block Diagram
    2. 22.2  ADC Configurability
      1. 22.2.1 ADC Clock Configuration
      2. 22.2.2 Resolution
      3. 22.2.3 Voltage Reference
        1. 22.2.3.1 External Reference Mode
        2. 22.2.3.2 Internal Reference Mode
        3. 22.2.3.3 Ganged References
        4. 22.2.3.4 Selecting Reference Mode
      4. 22.2.4 Signal Mode
        1. 22.2.4.1 Expected Conversion Results
        2. 22.2.4.2 Interpreting Conversion Results
    3. 22.3  SOC Principle of Operation
      1. 22.3.1 ADC Sequencer
      2. 22.3.2 SOC Configuration
      3. 22.3.3 Trigger Operation
        1. 22.3.3.1 Global Software Trigger
        2. 22.3.3.2 Trigger Repeaters
          1. 22.3.3.2.1 Oversampling Mode
          2. 22.3.3.2.2 Undersampling Mode
          3. 22.3.3.2.3 Trigger Phase Delay
          4. 22.3.3.2.4 Re-trigger Spread
          5. 22.3.3.2.5 Trigger Repeater Configuration
            1. 22.3.3.2.5.1 Register Shadow Updates
          6. 22.3.3.2.6 Re-Trigger Logic
          7. 22.3.3.2.7 Multi-Path Triggering Behavior
      4. 22.3.4 ADC Acquisition (Sample and Hold) Window
      5. 22.3.5 ADC Input Models
      6. 22.3.6 Channel Selection
        1. 22.3.6.1 External Channel Selection
          1. 22.3.6.1.1 External Channel Selection Timing
    4. 22.4  SOC Configuration Examples
      1. 22.4.1 Single Conversion from ePWM Trigger
      2. 22.4.2 Oversampled Conversion from ePWM Trigger
      3. 22.4.3 Multiple Conversions from CPU Timer Trigger
      4. 22.4.4 Software Triggering of SOCs
    5. 22.5  ADC Conversion Priority
    6. 22.6  Burst Mode
      1. 22.6.1 Burst Mode Example
      2. 22.6.2 Burst Mode Priority Example
    7. 22.7  EOC and Interrupt Operation
      1. 22.7.1 Interrupt Overflow
      2. 22.7.2 Continue to Interrupt Mode
      3. 22.7.3 Early Interrupt Configuration Mode
    8. 22.8  Post-Processing Blocks
      1. 22.8.1 PPB Offset Correction
      2. 22.8.2 PPB Error Calculation
      3. 22.8.3 PPB Result Delta Calculation
      4. 22.8.4 PPB Limit Detection and Zero-Crossing Detection
        1. 22.8.4.1 PPB Digital Trip Filter
      5. 22.8.5 PPB Oversampling
        1. 22.8.5.1 Accumulation, Minimum, Maximum, and Average Functions
        2. 22.8.5.2 Outlier Rejection
    9. 22.9  Result Safety Checker
      1. 22.9.1 Result Safety Checker Operation
      2. 22.9.2 Result Safety Checker Interrupts and Events
    10. 22.10 Opens/Shorts Detection Circuit (OSDETECT)
      1. 22.10.1 Open Short Detection Implementation
      2. 22.10.2 Detecting an Open Input Pin
      3. 22.10.3 Detecting a Shorted Input Pin
    11. 22.11 Power-Up Sequence
    12. 22.12 ADC Calibration
      1. 22.12.1 ADC Zero Offset Calibration
    13. 22.13 ADC Timings
      1. 22.13.1 ADC Timing Diagrams
      2. 22.13.2 Post-Processing Block Timings
    14. 22.14 Additional Information
      1. 22.14.1 Ensuring Synchronous Operation
        1. 22.14.1.1 Basic Synchronous Operation
        2. 22.14.1.2 Synchronous Operation with Multiple Trigger Sources
        3. 22.14.1.3 Synchronous Operation with Uneven SOC Numbers
        4. 22.14.1.4 Synchronous Operation with Different Resolutions
        5. 22.14.1.5 Non-overlapping Conversions
      2. 22.14.2 Choosing an Acquisition Window Duration
      3. 22.14.3 Achieving Simultaneous Sampling
      4. 22.14.4 Result Register Mapping
      5. 22.14.5 Internal Temperature Sensor
      6. 22.14.6 Designing an External Reference Circuit
      7. 22.14.7 Internal Test Mode
      8. 22.14.8 ADC Gain and Offset Calibration
    15. 22.15 Software
      1. 22.15.1 ADC Registers to Driverlib Functions
      2. 22.15.2 ADC Examples
        1. 22.15.2.1  Using Analog Subsystems Lab - Sysconfig - SINGLE_CORE
        2. 22.15.2.2  ADC Software Triggering - SINGLE_CORE
        3. 22.15.2.3  ADC ePWM Triggering - SINGLE_CORE
        4. 22.15.2.4  ADC Temperature Sensor Conversion - SINGLE_CORE
        5. 22.15.2.5  ADC Synchronous SOC Software Force (adc_soc_software_sync) - SINGLE_CORE
        6. 22.15.2.6  ADC Continuous Triggering (adc_soc_continuous) - SINGLE_CORE
        7. 22.15.2.7  ADC Continuous Conversions Read by DMA (adc_soc_continuous_dma) - SINGLE_CORE
        8. 22.15.2.8  ADC PPB Offset (adc_ppb_offset) - SINGLE_CORE
        9. 22.15.2.9  ADC PPB Limits (adc_ppb_limits) - SINGLE_CORE
        10. 22.15.2.10 ADC PPB Delay Capture (adc_ppb_delay) - SINGLE_CORE
        11. 22.15.2.11 ADC ePWM Triggering Multiple SOC - SINGLE_CORE
        12. 22.15.2.12 ADC Burst Mode - SINGLE_CORE
        13. 22.15.2.13 ADC Burst Mode Oversampling - SINGLE_CORE
        14. 22.15.2.14 ADC SOC Oversampling - SINGLE_CORE
        15. 22.15.2.15 ADC PPB PWM trip (adc_ppb_pwm_trip) - SINGLE_CORE
        16. 22.15.2.16 ADC Trigger Repeater Oversampling - SINGLE_CORE
        17. 22.15.2.17 ADC Trigger Repeater Undersampling - SINGLE_CORE
        18. 22.15.2.18 ADC Safety Checker - SINGLE_CORE
        19. 22.15.2.19 ADC Fast Oversampling (with Trigger Repeater) - SINGLE_CORE
    16. 22.16 ADC Registers
      1. 22.16.1 ADC Base Address Table
      2. 22.16.2 ADC_RESULT_REGS Registers
      3. 22.16.3 ADC_REGS Registers
      4. 22.16.4 ADC_SAFECHECK_REGS Registers
      5. 22.16.5 ADC_SAFECHECK_INTEVT_REGS Registers
      6. 22.16.6 ADC_GLOBAL_REGS Registers
  27. 23Buffered Digital-to-Analog Converter (DAC)
    1. 23.1 Introduction
      1. 23.1.1 DAC Related Collateral
      2. 23.1.2 DAC Features
      3. 23.1.3 Block Diagram
    2. 23.2 Using the DAC
      1. 23.2.1 Initialization Sequence
      2. 23.2.2 DAC Offset Adjustment
      3. 23.2.3 EPWMSYNCPER Signal
    3. 23.3 Lock Registers
    4. 23.4 Software
      1. 23.4.1 DAC Registers to Driverlib Functions
      2. 23.4.2 DAC Examples
        1. 23.4.2.1 Buffered DAC Enable - SINGLE_CORE
        2. 23.4.2.2 Buffered DAC Random - SINGLE_CORE
    5. 23.5 DAC Registers
      1. 23.5.1 DAC Base Address Table
      2. 23.5.2 DAC_REGS Registers
  28. 24Comparator Subsystem (CMPSS)
    1. 24.1 Introduction
      1. 24.1.1 Features
      2. 24.1.2 CMPSS Related Collateral
      3. 24.1.3 Block Diagram
    2. 24.2 Comparator
    3. 24.3 Reference DAC
    4. 24.4 Ramp Generator
      1. 24.4.1 Ramp Generator Overview
      2. 24.4.2 Ramp Generator Behavior
      3. 24.4.3 Ramp Generator Behavior at Corner Cases
    5. 24.5 Digital Filter
      1. 24.5.1 Filter Initialization Sequence
    6. 24.6 Using the CMPSS
      1. 24.6.1 LATCHCLR, EPWMSYNCPER, and EPWMBLANK Signals
      2. 24.6.2 Synchronizer, Digital Filter, and Latch Delays
      3. 24.6.3 Calibrating the CMPSS
      4. 24.6.4 Enabling and Disabling the CMPSS Clock
    7. 24.7 Software
      1. 24.7.1 CMPSS Registers to Driverlib Functions
      2. 24.7.2 CMPSS Examples
        1. 24.7.2.1 CMPSS Asynchronous Trip - SINGLE_CORE
        2. 24.7.2.2 CMPSS Digital Filter Configuration - SINGLE_CORE
    8. 24.8 CMPSS Registers
      1. 24.8.1 CMPSS Base Address Table
      2. 24.8.2 CMPSS_REGS Registers
      3. 24.8.3 CMPSS_LITE_REGS Registers
    9. 24.9 CMPSS Registers
      1. 24.9.1 CMPSS Base Address Table
      2. 24.9.2 CMPSS_REGS Registers
  29.   ► CONTROL PERIPHERALS
    1.     Technical Reference Manual Overview
  30. 25Enhanced Capture (eCAP)
    1. 25.1 Introduction
      1. 25.1.1 Features
      2. 25.1.2 ECAP Related Collateral
    2. 25.2 Description
    3. 25.3 Configuring Device Pins for the eCAP
    4. 25.4 Capture and APWM Operating Mode
    5. 25.5 Capture Mode Description
      1. 25.5.1  Event Prescaler
      2. 25.5.2  Glitch Filter
      3. 25.5.3  Edge Polarity Select and Qualifier
      4. 25.5.4  Continuous/One-Shot Control
      5. 25.5.5  32-Bit Counter and Phase Control
      6. 25.5.6  CAP1-CAP4 Registers
      7. 25.5.7  eCAP Synchronization
        1. 25.5.7.1 Example 1 - Using SWSYNC with ECAP Module
      8. 25.5.8  Interrupt Control
      9. 25.5.9  RTDMA Interrupt
      10. 25.5.10 ADC SOC Event
      11. 25.5.11 Shadow Load and Lockout Control
      12. 25.5.12 APWM Mode Operation
      13. 25.5.13 Signal Monitoring Unit
        1. 25.5.13.1 Pulse Width and Period Monitoring
          1. 25.5.13.1.1 eCAP - eCAP Global Strobe Selection
        2. 25.5.13.2 Edge Monitoring
    6. 25.6 Application of the eCAP Module
      1. 25.6.1 Example 1 - Absolute Time-Stamp Operation Rising-Edge Trigger
      2. 25.6.2 Example 2 - Absolute Time-Stamp Operation Rising- and Falling-Edge Trigger
      3. 25.6.3 Example 3 - Time Difference (Delta) Operation Rising-Edge Trigger
      4. 25.6.4 Example 4 - Time Difference (Delta) Operation Rising- and Falling-Edge Trigger
    7. 25.7 Application of the APWM Mode
      1. 25.7.1 Example 1 - Simple PWM Generation (Independent Channels)
    8. 25.8 Software
      1. 25.8.1 ECAP Registers to Driverlib Functions
      2. 25.8.2 ECAP Examples
        1. 25.8.2.1 eCAP APWM Phase-shift Example - SINGLE_CORE
        2. 25.8.2.2 eCAP APWM Example - SINGLE_CORE
        3. 25.8.2.3 eCAP Capture PWM Example - SINGLE_CORE
        4. 25.8.2.4 eCAP APWM Phase-shift Example - SINGLE_CORE
        5. 25.8.2.5 ecap_ex4_dma_transfer - SINGLE_CORE
    9. 25.9 ECAP Registers
      1. 25.9.1 ECAP Base Address Table
      2. 25.9.2 ECAP_REGS Registers
      3. 25.9.3 ECAP_SIGNAL_MONITORING Registers
      4. 25.9.4 HRCAP_REGS Registers
  31. 26High Resolution Capture (HRCAP)
    1. 26.1 Introduction
      1. 26.1.1 HRCAP Related Collateral
      2. 26.1.2 Features
      3. 26.1.3 Description
    2. 26.2 Operational Details
      1. 26.2.1 HRCAP Clocking
      2. 26.2.2 HRCAP Initialization Sequence
      3. 26.2.3 HRCAP Interrupts
      4. 26.2.4 HRCAP Calibration
        1. 26.2.4.1 Applying the Scale Factor
    3. 26.3 Known Exceptions
    4. 26.4 Software
      1. 26.4.1 HRCAP Examples
        1. 26.4.1.1 HRCAP Capture and Calibration Example - SINGLE_CORE
    5. 26.5 HRCAP Registers
      1. 26.5.1 HRCAP Base Address Table
      2. 26.5.2 HRCAP_REGS Registers
  32. 27Enhanced Pulse Width Modulator (ePWM)
    1. 27.1  Introduction
      1. 27.1.1 EPWM Related Collateral
      2. 27.1.2 Submodule Overview
    2. 27.2  Configuring Device Pins
    3. 27.3  ePWM Modules Overview
    4. 27.4  Time-Base (TB) Submodule
      1. 27.4.1 Purpose of the Time-Base Submodule
      2. 27.4.2 Controlling and Monitoring the Time-Base Submodule
      3. 27.4.3 Calculating PWM Period and Frequency
        1. 27.4.3.1 Time-Base Period Shadow Register
        2. 27.4.3.2 Time-Base Clock Synchronization
        3. 27.4.3.3 Time-Base Counter Synchronization
        4. 27.4.3.4 ePWM SYNC Selection
      4. 27.4.4 Phase Locking the Time-Base Clocks of Multiple ePWM Modules
      5. 27.4.5 Simultaneous Writes Between ePWM Register Instances
      6. 27.4.6 Time-Base Counter Modes and Timing Waveforms
      7. 27.4.7 Global Load
        1. 27.4.7.1 Global Load Pulse Pre-Scalar
        2. 27.4.7.2 One-Shot Load Mode
        3. 27.4.7.3 One-Shot Sync Mode
    5. 27.5  Counter-Compare (CC) Submodule
      1. 27.5.1 Purpose of the Counter-Compare Submodule
      2. 27.5.2 Controlling and Monitoring the Counter-Compare Submodule
      3. 27.5.3 Operational Highlights for the Counter-Compare Submodule
      4. 27.5.4 Count Mode Timing Waveforms
    6. 27.6  Action-Qualifier (AQ) Submodule
      1. 27.6.1 Purpose of the Action-Qualifier Submodule
      2. 27.6.2 Action-Qualifier Submodule Control and Status Register Definitions
      3. 27.6.3 Action-Qualifier Event Priority
      4. 27.6.4 AQCTLA and AQCTLB Shadow Mode Operations
      5. 27.6.5 Configuration Requirements for Common Waveforms
    7. 27.7  XCMP Complex Waveform Generator Mode
      1. 27.7.1 XCMP Allocation to CMPA and CMPB
      2. 27.7.2 XCMP Shadow Buffers
      3. 27.7.3 XCMP Operation
    8. 27.8  Dead-Band Generator (DB) Submodule
      1. 27.8.1 Purpose of the Dead-Band Submodule
      2. 27.8.2 Dead-band Submodule Additional Operating Modes
      3. 27.8.3 Operational Highlights for the Dead-Band Submodule
    9. 27.9  PWM Chopper (PC) Submodule
      1. 27.9.1 Purpose of the PWM Chopper Submodule
      2. 27.9.2 Operational Highlights for the PWM Chopper Submodule
      3. 27.9.3 Waveforms
        1. 27.9.3.1 One-Shot Pulse
        2. 27.9.3.2 Duty Cycle Control
    10. 27.10 Trip-Zone (TZ) Submodule
      1. 27.10.1 Purpose of the Trip-Zone Submodule
      2. 27.10.2 Operational Highlights for the Trip-Zone Submodule
        1. 27.10.2.1 Trip-Zone Configurations
      3. 27.10.3 Generating Trip Event Interrupts
    11. 27.11 Diode Emulation (DE) Submodule
      1. 27.11.1 DEACTIVE Mode
      2. 27.11.2 Exiting DE Mode
      3. 27.11.3 Re-Entering DE Mode
      4. 27.11.4 DE Monitor
    12. 27.12 Minimum Dead-Band (MINDB) + Illegal Combination Logic (ICL) Submodules
      1. 27.12.1 Minimum Dead-Band (MINDB)
      2. 27.12.2 Illegal Combo Logic (ICL)
    13. 27.13 Event-Trigger (ET) Submodule
      1. 27.13.1 Operational Overview of the ePWM Event-Trigger Submodule
    14. 27.14 Digital Compare (DC) Submodule
      1. 27.14.1 Purpose of the Digital Compare Submodule
      2. 27.14.2 Enhanced Trip Action Using CMPSS
      3. 27.14.3 Using CMPSS to Trip the ePWM on a Cycle-by-Cycle Basis
      4. 27.14.4 Operation Highlights of the Digital Compare Submodule
        1. 27.14.4.1 Digital Compare Events
        2. 27.14.4.2 Event Filtering
        3. 27.14.4.3 Valley Switching
        4. 27.14.4.4 Event Detection
          1. 27.14.4.4.1 Input Signal Detection
          2. 27.14.4.4.2 MIN and MAX Detection Circuit
    15. 27.15 ePWM Crossbar (X-BAR)
    16. 27.16 Applications to Power Topologies
      1. 27.16.1  Overview of Multiple Modules
      2. 27.16.2  Key Configuration Capabilities
      3. 27.16.3  Controlling Multiple Buck Converters With Independent Frequencies
      4. 27.16.4  Controlling Multiple Buck Converters With Same Frequencies
      5. 27.16.5  Controlling Multiple Half H-Bridge (HHB) Converters
      6. 27.16.6  Controlling Dual 3-Phase Inverters for Motors (ACI and PMSM)
      7. 27.16.7  Practical Applications Using Phase Control Between PWM Modules
      8. 27.16.8  Controlling a 3-Phase Interleaved DC/DC Converter
      9. 27.16.9  Controlling Zero Voltage Switched Full Bridge (ZVSFB) Converter
      10. 27.16.10 Controlling a Peak Current Mode Controlled Buck Module
      11. 27.16.11 Controlling H-Bridge LLC Resonant Converter
    17. 27.17 Register Lock Protection
    18. 27.18 High-Resolution Pulse Width Modulator (HRPWM)
      1. 27.18.1 Operational Description of HRPWM
        1. 27.18.1.1 Controlling the HRPWM Capabilities
        2. 27.18.1.2 HRPWM Source Clock
        3. 27.18.1.3 Configuring the HRPWM
        4. 27.18.1.4 Configuring High-Resolution in Deadband Rising-Edge and Falling-Edge Delay
        5. 27.18.1.5 Principle of Operation
          1. 27.18.1.5.1 Edge Positioning
          2. 27.18.1.5.2 Scaling Considerations
          3. 27.18.1.5.3 Duty Cycle Range Limitation
          4. 27.18.1.5.4 High-Resolution Period
            1. 27.18.1.5.4.1 High-Resolution Period Configuration
        6. 27.18.1.6 Deadband High-Resolution Operation
        7. 27.18.1.7 Scale Factor Optimizing Software (SFO)
        8. 27.18.1.8 HRPWM Examples Using Optimized Assembly Code
          1. 27.18.1.8.1 #Defines for HRPWM Header Files
          2. 27.18.1.8.2 Implementing a Simple Buck Converter
            1. 27.18.1.8.2.1 HRPWM Buck Converter Initialization Code
            2. 27.18.1.8.2.2 HRPWM Buck Converter Run-Time Code
          3. 27.18.1.8.3 Implementing a DAC Function Using an R+C Reconstruction Filter
            1. 27.18.1.8.3.1 PWM DAC Function Initialization Code
            2. 27.18.1.8.3.2 PWM DAC Function Run-Time Code
      2. 27.18.2 SFO Library Software - SFO_TI_Build_V8.lib
        1. 27.18.2.1 Scale Factor Optimizer Function - int SFO()
        2. 27.18.2.2 Software Usage
          1. 27.18.2.2.1 A Sample of How to Add "Include" Files
          2.        1169
          3. 27.18.2.2.2 Declaring an Element
          4.        1171
          5. 27.18.2.2.3 Initializing With a Scale Factor Value
          6.        1173
          7. 27.18.2.2.4 SFO Function Calls
    19. 27.19 Software
      1. 27.19.1 EPWM Registers to Driverlib Functions
      2. 27.19.2 HRPWMCAL Registers to Driverlib Functions
      3. 27.19.3 EPWM Examples
        1. 27.19.3.1  ePWM Trip Zone - SINGLE_CORE
        2. 27.19.3.2  ePWM Up Down Count Action Qualifier with FRAMESEL and IPC - MULTI_CORE
        3. 27.19.3.3  ePWM Up Down Count Action Qualifier with FRAMESEL and IPC - MULTI_CORE
        4. 27.19.3.4  ePWM Up Down Count Action Qualifier - SINGLE_CORE
        5. 27.19.3.5  ePWM Synchronization - SINGLE_CORE
        6. 27.19.3.6  ePWM Digital Compare - SINGLE_CORE
        7. 27.19.3.7  ePWM Digital Compare Event Filter Blanking Window - SINGLE_CORE
        8. 27.19.3.8  ePWM Valley Switching - SINGLE_CORE
        9. 27.19.3.9  ePWM Digital Compare Edge Filter - SINGLE_CORE
        10. 27.19.3.10 ePWM Deadband - SINGLE_CORE
        11. 27.19.3.11 ePWM DMA - SINGLE_CORE
        12. 27.19.3.12 ePWM Chopper - SINGLE_CORE
        13. 27.19.3.13 EPWM Configure Signal - SINGLE_CORE
        14. 27.19.3.14 Realization of Monoshot mode - SINGLE_CORE
        15. 27.19.3.15 EPWM Action Qualifier (epwm_up_aq) - SINGLE_CORE
        16. 27.19.3.16 ePWM XCMP Mode - SINGLE_CORE
        17. 27.19.3.17 ePWM Event Detection - SINGLE_CORE
      4. 27.19.4 HRPWM Examples
        1. 27.19.4.1 HRPWM Duty Control with SFO - SINGLE_CORE
        2. 27.19.4.2 HRPWM Period Control - SINGLE_CORE
        3. 27.19.4.3 HRPWM XCMP Mode - SINGLE_CORE
    20. 27.20 EPWM Registers
      1. 27.20.1 EPWM Base Address Table
      2. 27.20.2 EPWM_REGS Registers
      3. 27.20.3 EPWM_XCMP_REGS Registers
      4. 27.20.4 DE_REGS Registers
      5. 27.20.5 MINDB_LUT_REGS Registers
      6. 27.20.6 HRPWMCAL_REGS Registers
  33. 28Enhanced Quadrature Encoder Pulse (eQEP)
    1. 28.1  Introduction
      1. 28.1.1 EQEP Related Collateral
    2. 28.2  Configuring Device Pins
    3. 28.3  Description
      1. 28.3.1 EQEP Inputs
      2. 28.3.2 Functional Description
      3. 28.3.3 eQEP Memory Map
    4. 28.4  Quadrature Decoder Unit (QDU)
      1. 28.4.1 Position Counter Input Modes
        1. 28.4.1.1 Quadrature Count Mode
        2. 28.4.1.2 Direction-Count Mode
        3. 28.4.1.3 Up-Count Mode
        4. 28.4.1.4 Down-Count Mode
      2. 28.4.2 eQEP Input Polarity Selection
      3. 28.4.3 Position-Compare Sync Output
    5. 28.5  Position Counter and Control Unit (PCCU)
      1. 28.5.1 Position Counter Operating Modes
        1. 28.5.1.1 Position Counter Reset on Index Event (QEPCTL[PCRM] = 00)
        2. 28.5.1.2 Position Counter Reset on Maximum Position (QEPCTL[PCRM] = 01)
        3. 28.5.1.3 Position Counter Reset on the First Index Event (QEPCTL[PCRM] = 10)
        4. 28.5.1.4 Position Counter Reset on Unit Time-out Event (QEPCTL[PCRM] = 11)
      2. 28.5.2 Position Counter Latch
        1. 28.5.2.1 Index Event Latch
        2. 28.5.2.2 Strobe Event Latch
      3. 28.5.3 Position Counter Initialization
      4. 28.5.4 eQEP Position-compare Unit
    6. 28.6  eQEP Edge Capture Unit
    7. 28.7  eQEP Watchdog
    8. 28.8  eQEP Unit Timer Base
    9. 28.9  QMA Module
      1. 28.9.1 Modes of Operation
        1. 28.9.1.1 QMA Mode-1 (QMACTRL[MODE] = 1)
        2. 28.9.1.2 QMA Mode-2 (QMACTRL[MODE] = 2)
      2. 28.9.2 Interrupt and Error Generation
    10. 28.10 eQEP Interrupt Structure
    11. 28.11 Software
      1. 28.11.1 EQEP Registers to Driverlib Functions
      2. 28.11.2 EQEP Examples
        1. 28.11.2.1 Frequency Measurement Using eQEP via unit timeout interrupt - SINGLE_CORE
        2. 28.11.2.2 Frequency Measurement Using eQEP via unit timeout interrupt - SINGLE_CORE
        3. 28.11.2.3 Motor speed and direction measurement using eQEP via unit timeout interrupt - SINGLE_CORE
    12. 28.12 EQEP Registers
      1. 28.12.1 EQEP Base Address Table
      2. 28.12.2 EQEP_REGS Registers
  34. 29Sigma Delta Filter Module (SDFM)
    1. 29.1  Introduction
      1. 29.1.1 SDFM Related Collateral
      2. 29.1.2 Features
      3. 29.1.3 Block Diagram
    2. 29.2  Configuring Device Pins
    3. 29.3  Input Qualification
    4. 29.4  Input Control Unit
    5. 29.5  SDFM Clock Control
    6. 29.6  Sinc Filter
      1. 29.6.1 Data Rate and Latency of the Sinc Filter
    7. 29.7  Data (Primary) Filter Unit
      1. 29.7.1 32-bit or 16-bit Data Filter Output Representation
      2. 29.7.2 Data FIFO
      3. 29.7.3 SDSYNC Event
    8. 29.8  Comparator (Secondary) Filter Unit
      1. 29.8.1 Higher Threshold (HLT) Comparators
      2. 29.8.2 Lower Threshold (LLT) Comparators
      3. 29.8.3 Digital Filter
    9. 29.9  Theoretical SDFM Filter Output
    10. 29.10 Interrupt Unit
      1. 29.10.1 SDFM (SDyERR) Interrupt Sources
      2. 29.10.2 Data Ready (DRINT) Interrupt Sources
    11. 29.11 SDFM Registers
      1. 29.11.1 SDFM Base Address Table
      2. 29.11.2 SDFM_REGS Registers
  35.   ► COMMUNICATION PERIPHERALS
    1.     Technical Reference Manual Overview
  36. 30Modular Controller Area Network (MCAN)
    1. 30.1 MCAN Introduction
      1. 30.1.1 MCAN Related Collateral
      2. 30.1.2 MCAN Features
    2. 30.2 MCAN Environment
    3. 30.3 CAN Network Basics
    4. 30.4 MCAN Integration
    5. 30.5 MCAN Functional Description
      1. 30.5.1  Module Clocking Requirements
      2. 30.5.2  Interrupt Requests
      3. 30.5.3  Operating Modes
        1. 30.5.3.1 Software Initialization
        2. 30.5.3.2 Normal Operation
        3. 30.5.3.3 CAN FD Operation
      4. 30.5.4  Transmitter Delay Compensation
        1. 30.5.4.1 Description
        2. 30.5.4.2 Transmitter Delay Compensation Measurement
      5. 30.5.5  Restricted Operation Mode
      6. 30.5.6  Bus Monitoring Mode
      7. 30.5.7  Disabled Automatic Retransmission (DAR) Mode
        1. 30.5.7.1 Frame Transmission in DAR Mode
      8. 30.5.8  Clock Stop Mode
        1. 30.5.8.1 Suspend Mode
        2. 30.5.8.2 Wakeup Request
      9. 30.5.9  Test Modes
        1. 30.5.9.1 External Loop Back Mode
        2. 30.5.9.2 Internal Loop Back Mode
      10. 30.5.10 Timestamp Generation
        1. 30.5.10.1 External Timestamp Counter
      11. 30.5.11 Timeout Counter
      12. 30.5.12 Safety
        1. 30.5.12.1 ECC Wrapper
        2. 30.5.12.2 ECC Aggregator
          1. 30.5.12.2.1 ECC Aggregator Overview
          2. 30.5.12.2.2 ECC Aggregator Registers
        3. 30.5.12.3 Reads to ECC Control and Status Registers
        4. 30.5.12.4 ECC Interrupts
      13. 30.5.13 Rx Handling
        1. 30.5.13.1 Acceptance Filtering
          1. 30.5.13.1.1 Range Filter
          2. 30.5.13.1.2 Filter for Specific IDs
          3. 30.5.13.1.3 Classic Bit Mask Filter
          4. 30.5.13.1.4 Standard Message ID Filtering
          5. 30.5.13.1.5 Extended Message ID Filtering
        2. 30.5.13.2 Rx FIFOs
          1. 30.5.13.2.1 Rx FIFO Blocking Mode
          2. 30.5.13.2.2 Rx FIFO Overwrite Mode
        3. 30.5.13.3 Dedicated Rx Buffers
          1. 30.5.13.3.1 Rx Buffer Handling
      14. 30.5.14 Tx Handling
        1. 30.5.14.1 Transmit Pause
        2. 30.5.14.2 Dedicated Tx Buffers
        3. 30.5.14.3 Tx FIFO
        4. 30.5.14.4 Tx Queue
        5. 30.5.14.5 Mixed Dedicated Tx Buffers/Tx FIFO
        6. 30.5.14.6 Mixed Dedicated Tx Buffers/Tx Queue
        7. 30.5.14.7 Transmit Cancellation
        8. 30.5.14.8 Tx Event Handling
      15. 30.5.15 FIFO Acknowledge Handling
      16. 30.5.16 Message RAM
        1. 30.5.16.1 Message RAM Configuration
        2. 30.5.16.2 Rx Buffer and FIFO Element
        3. 30.5.16.3 Tx Buffer Element
        4. 30.5.16.4 Tx Event FIFO Element
        5. 30.5.16.5 Standard Message ID Filter Element
        6. 30.5.16.6 Extended Message ID Filter Element
    6. 30.6 Software
      1. 30.6.1 MCAN Examples
        1. 30.6.1.1 MCAN Loopback with Interrupts Example Using SYSCONFIG Tool - SINGLE_CORE
        2. 30.6.1.2 MCAN Loopback with Polling Example Using SYSCONFIG Tool - SINGLE_CORE
        3. 30.6.1.3 MCAN Loopback with Interrupts Example Using SYSCONFIG Tool - SINGLE_CORE
        4. 30.6.1.4 MCAN External Transmit using Tx Buffer - SINGLE_CORE
        5. 30.6.1.5 MCAN receive using Rx Buffer - SINGLE_CORE
        6. 30.6.1.6 MCAN External Transmit using Tx Buffer - SINGLE_CORE
    7. 30.7 MCAN Registers
      1. 30.7.1 MCAN Base Address Table
      2. 30.7.2 MCANSS_REGS Registers
      3. 30.7.3 MCAN_REGS Registers
      4. 30.7.4 MCAN_ERROR_REGS Registers
  37. 31EtherCAT® SubordinateDevice Controller (ESC)
    1. 31.1 Introduction
      1. 31.1.1  EtherCAT Related Collateral
      2. 31.1.2  ESC Features
      3. 31.1.3  ESC Subsystem Integrated Features
      4. 31.1.4  ESC versus Beckhoff ET1100
      5. 31.1.5  EtherCAT IP Block Diagram
      6. 31.1.6  ESC Functional Blocks
        1. 31.1.6.1  Interface to EtherCAT MainDevice
        2. 31.1.6.2  Process Data Interface
        3. 31.1.6.3  General-Purpose Inputs and Outputs
        4. 31.1.6.4  EtherCAT Processing Unit (EPU)
        5. 31.1.6.5  Fieldbus Memory Management Unit (FMMU)
        6. 31.1.6.6  Sync Manager
        7. 31.1.6.7  Monitoring
        8. 31.1.6.8  Reset Controller
        9. 31.1.6.9  PHY Management
        10. 31.1.6.10 Distributed Clock (DC)
        11. 31.1.6.11 EEPROM
        12. 31.1.6.12 Status / LEDs
      7. 31.1.7  EtherCAT Physical Layer
        1. 31.1.7.1 MII Interface
        2. 31.1.7.2 PHY Management Interface
          1. 31.1.7.2.1 PHY Address Configuration
          2. 31.1.7.2.2 PHY Reset Signal
          3. 31.1.7.2.3 PHY Clock
      8. 31.1.8  EtherCAT Protocol
      9. 31.1.9  EtherCAT State Machine (ESM)
      10. 31.1.10 More Information on EtherCAT
      11. 31.1.11 Beckhoff® Automation EtherCAT IP Errata
    2. 31.2 ESC and ESCSS Description
      1. 31.2.1  ESC RAM Parity and Memory Address Maps
        1. 31.2.1.1 ESC RAM Parity Logic
        2. 31.2.1.2 CPU1 ESC Memory Address Map
        3. 31.2.1.3 CPU2 ESC Memory Address Map
      2. 31.2.2  Local Host Communication
        1. 31.2.2.1 Byte Accessibility Through PDI
        2. 31.2.2.2 Software Details for Operation Across Clock Domains
      3. 31.2.3  Debug Emulation Mode Operation
      4. 31.2.4  ESC SubSystem
        1. 31.2.4.1 CPU1 Bus Interface
        2. 31.2.4.2 CPU2/CPU3 Bus Interface
      5. 31.2.5  Interrupts and Interrupt Mapping
      6. 31.2.6  Power, Clocks, and Resets
        1. 31.2.6.1 Power
        2. 31.2.6.2 Clocking
        3. 31.2.6.3 Resets
          1. 31.2.6.3.1 Chip-Level Reset
          2. 31.2.6.3.2 EtherCAT Soft Resets
          3. 31.2.6.3.3 Reset Out (RESET_OUT)
      7. 31.2.7  LED Controls
      8. 31.2.8  SubordinateDevice Node Configuration and EEPROM
      9. 31.2.9  General-Purpose Inputs and Outputs
        1. 31.2.9.1 General-Purpose Inputs
        2. 31.2.9.2 General-Purpose Output
      10. 31.2.10 Distributed Clocks – Sync and Latch
        1. 31.2.10.1 Clock Synchronization
        2. 31.2.10.2 SYNC Signals
          1. 31.2.10.2.1 Seeking Host Intervention
        3. 31.2.10.3 LATCH Signals
          1. 31.2.10.3.1 Timestamping
        4. 31.2.10.4 Device Control and Synchronization
          1. 31.2.10.4.1 Synchronization of PWM
          2. 31.2.10.4.2 ECAP SYNC Inputs
          3. 31.2.10.4.3 SYNC Signal Conditioning and Rerouting
    3. 31.3 Software Initialization Sequence and Allocating Ownership
    4. 31.4 ESC Configuration Constants
    5. 31.5 Software
      1. 31.5.1 ECAT_SS Registers to Driverlib Functions
      2. 31.5.2 ETHERNET Examples
    6. 31.6 ETHERCAT Registers
      1. 31.6.1 ETHERCAT Base Address Table
      2. 31.6.2 ESCSS_REGS Registers
      3. 31.6.3 ESCSS_CONFIG_REGS Registers
  38. 32Fast Serial Interface (FSI)
    1. 32.1 Introduction
      1. 32.1.1 FSI Related Collateral
      2. 32.1.2 FSI Features
    2. 32.2 System-level Integration
      1. 32.2.1 CPU Interface
      2. 32.2.2 Signal Description
        1. 32.2.2.1 Configuring Device Pins
      3. 32.2.3 FSI Interrupts
        1. 32.2.3.1 Transmitter Interrupts
        2. 32.2.3.2 Receiver Interrupts
        3. 32.2.3.3 Configuring Interrupts
        4. 32.2.3.4 Handling Interrupts
      4. 32.2.4 RTDMA Interface
      5. 32.2.5 External Frame Trigger Mux
    3. 32.3 FSI Functional Description
      1. 32.3.1 Introduction to Operation
      2. 32.3.2 FSI Transmitter Module
        1. 32.3.2.1 Initialization
        2. 32.3.2.2 FSI_TX Clocking
        3. 32.3.2.3 Transmitting Frames
          1. 32.3.2.3.1 Software Triggered Frames
          2. 32.3.2.3.2 Externally Triggered Frames
          3. 32.3.2.3.3 Ping Frame Generation
            1. 32.3.2.3.3.1 Automatic Ping Frames
            2. 32.3.2.3.3.2 Software Triggered Ping Frame
            3. 32.3.2.3.3.3 Externally Triggered Ping Frame
          4. 32.3.2.3.4 Transmitting Frames with RTDMA
        4. 32.3.2.4 Transmit Buffer Management
        5. 32.3.2.5 CRC Submodule
        6. 32.3.2.6 Conditions in Which the Transmitter Must Undergo a Soft Reset
        7. 32.3.2.7 Reset
      3. 32.3.3 FSI Receiver Module
        1. 32.3.3.1  Initialization
        2. 32.3.3.2  FSI_RX Clocking
        3. 32.3.3.3  Receiving Frames
          1. 32.3.3.3.1 Receiving Frames with RTDMA
        4. 32.3.3.4  Ping Frame Watchdog
        5. 32.3.3.5  Frame Watchdog
        6. 32.3.3.6  Delay Line Control
        7. 32.3.3.7  Buffer Management
        8. 32.3.3.8  CRC Submodule
        9. 32.3.3.9  Using the Zero Bits of the Receiver Tag Registers
        10. 32.3.3.10 Conditions in Which the Receiver Must Undergo a Soft Reset
        11. 32.3.3.11 FSI_RX Reset
      4. 32.3.4 Frame Format
        1. 32.3.4.1 FSI Frame Phases
        2. 32.3.4.2 Frame Types
          1. 32.3.4.2.1 Ping Frames
          2. 32.3.4.2.2 Error Frames
          3. 32.3.4.2.3 Data Frames
        3. 32.3.4.3 Multi-Lane Transmission
      5. 32.3.5 Flush Sequence
      6. 32.3.6 Internal Loopback
      7. 32.3.7 CRC Generation
      8. 32.3.8 ECC Module
      9. 32.3.9 FSI-SPI Compatibility Mode
        1. 32.3.9.1 Available SPI Modes
          1. 32.3.9.1.1 FSITX as SPI Controller, Transmit Only
            1. 32.3.9.1.1.1 Initialization
            2. 32.3.9.1.1.2 Operation
          2. 32.3.9.1.2 FSIRX as SPI Peripheral, Receive Only
            1. 32.3.9.1.2.1 Initialization
            2. 32.3.9.1.2.2 Operation
          3. 32.3.9.1.3 FSITX and FSIRX Emulating a Full Duplex SPI Controller
            1. 32.3.9.1.3.1 Initialization
            2. 32.3.9.1.3.2 Operation
    4. 32.4 FSI Programing Guide
      1. 32.4.1 Establishing the Communication Link
        1. 32.4.1.1 Establishing the Communication Link from the Main Device
        2. 32.4.1.2 Establishing the Communication Link from the Remote Device
      2. 32.4.2 Register Protection
      3. 32.4.3 Emulation Mode
    5. 32.5 Software
      1. 32.5.1 FSI Registers to Driverlib Functions
      2. 32.5.2 FSI Examples
        1. 32.5.2.1 Lab solution on Using Communication Peripherals - SINGLE_CORE
        2. 32.5.2.2 FSI Loopback:CPU Control - SINGLE_CORE
        3. 32.5.2.3 FSI data transfers upon CPU Timer event - SINGLE_CORE
    6. 32.6 FSI Registers
      1. 32.6.1 FSI Base Address Table
      2. 32.6.2 FSI_TX_REGS Registers
      3. 32.6.3 FSI_RX_REGS Registers
  39. 33Inter-Integrated Circuit Module (I2C)
    1. 33.1 Introduction
      1. 33.1.1 I2C Related Collateral
      2. 33.1.2 Features
      3. 33.1.3 Features Not Supported
      4. 33.1.4 Functional Overview
      5. 33.1.5 Clock Generation
      6. 33.1.6 I2C Clock Divider Registers (I2CCLKL and I2CCLKH)
        1. 33.1.6.1 Formula for the Controller Clock Period
    2. 33.2 Configuring Device Pins
    3. 33.3 I2C Module Operational Details
      1. 33.3.1  Input and Output Voltage Levels
      2. 33.3.2  Selecting Pullup Resistors
      3. 33.3.3  Data Validity
      4. 33.3.4  Operating Modes
      5. 33.3.5  I2C Module START and STOP Conditions
      6. 33.3.6  Non-repeat Mode versus Repeat Mode
      7. 33.3.7  Serial Data Formats
        1. 33.3.7.1 7-Bit Addressing Format
        2. 33.3.7.2 10-Bit Addressing Format
        3. 33.3.7.3 Free Data Format
        4. 33.3.7.4 Using a Repeated START Condition
      8. 33.3.8  Clock Synchronization
      9. 33.3.9  Clock Stretching
      10. 33.3.10 Arbitration
      11. 33.3.11 Digital Loopback Mode
      12. 33.3.12 NACK Bit Generation
    4. 33.4 Interrupt Requests Generated by the I2C Module
      1. 33.4.1 Basic I2C Interrupt Requests
      2. 33.4.2 I2C FIFO Interrupts
    5. 33.5 Resetting or Disabling the I2C Module
    6. 33.6 Software
      1. 33.6.1 I2C Registers to Driverlib Functions
      2. 33.6.2 I2C Examples
        1. 33.6.2.1 I2C Digital Loopback with FIFO Interrupts - SINGLE_CORE
        2. 33.6.2.2 I2C EEPROM - SINGLE_CORE
        3. 33.6.2.3 I2C Digital External Loopback with FIFO Interrupts - SINGLE_CORE
        4. 33.6.2.4 I2C Extended Clock Stretching Controller TX - SINGLE_CORE
        5. 33.6.2.5 I2C Extended Clock Stretching Target RX - SINGLE_CORE
    7. 33.7 I2C Registers
      1. 33.7.1 I2C Base Address Table
      2. 33.7.2 I2C_REGS Registers
  40. 34Power Management Bus Module (PMBus)
    1. 34.1 Introduction
      1. 34.1.1 PMBUS Related Collateral
      2. 34.1.2 Features
      3. 34.1.3 Block Diagram
    2. 34.2 Configuring Device Pins
    3. 34.3 Target Mode Operation
      1. 34.3.1 Configuration
      2. 34.3.2 Message Handling
        1. 34.3.2.1  Quick Command
        2. 34.3.2.2  Send Byte
        3. 34.3.2.3  Receive Byte
        4. 34.3.2.4  Write Byte and Write Word
        5. 34.3.2.5  Read Byte and Read Word
        6. 34.3.2.6  Process Call
        7. 34.3.2.7  Block Write
        8. 34.3.2.8  Block Read
        9. 34.3.2.9  Block Write-Block Read Process Call
        10. 34.3.2.10 Alert Response
        11. 34.3.2.11 Extended Command
        12. 34.3.2.12 Group Command
    4. 34.4 Controller Mode Operation
      1. 34.4.1 Configuration
      2. 34.4.2 Message Handling
        1. 34.4.2.1  Quick Command
        2. 34.4.2.2  Send Byte
        3. 34.4.2.3  Receive Byte
        4. 34.4.2.4  Write Byte and Write Word
        5. 34.4.2.5  Read Byte and Read Word
        6. 34.4.2.6  Process Call
        7. 34.4.2.7  Block Write
        8. 34.4.2.8  Block Read
        9. 34.4.2.9  Block Write-Block Read Process Call
        10. 34.4.2.10 Alert Response
        11. 34.4.2.11 Extended Command
        12. 34.4.2.12 Group Command
    5. 34.5 Software
      1. 34.5.1 PMBUS Registers to Driverlib Functions
      2. 34.5.2 PMBUS Examples
        1. 34.5.2.1 PMBus in I2C Mode Controller - SINGLE_CORE
        2. 34.5.2.2 PMBus in I2C Mode Target - SINGLE_CORE
    6. 34.6 PMBUS Registers
      1. 34.6.1 PMBUS Base Address Table
      2. 34.6.2 PMBUS_REGS Registers
  41. 35Universal Asynchronous Receiver/Transmitter (UART)
    1. 35.1 Introduction
      1. 35.1.1 Features
      2. 35.1.2 UART Related Collateral
      3. 35.1.3 Block Diagram
    2. 35.2 Functional Description
      1. 35.2.1 Transmit and Receive Logic
      2. 35.2.2 Baud-Rate Generation
      3. 35.2.3 Data Transmission
      4. 35.2.4 Serial IR (SIR)
      5. 35.2.5 9-Bit UART Mode
      6. 35.2.6 FIFO Operation
      7. 35.2.7 Interrupts
      8. 35.2.8 Loopback Operation
      9. 35.2.9 RTDMA Operation
        1. 35.2.9.1 Receiving Data Using UART with RTDMA
        2. 35.2.9.2 Transmitting Data Using UART with RTDMA
    3. 35.3 Initialization and Configuration
    4. 35.4 Software
      1. 35.4.1 UART Registers to Driverlib Functions
      2. 35.4.2 UART Examples
        1. 35.4.2.1 UART Academy Lab - SINGLE_CORE
        2. 35.4.2.2 UART Loopback - SINGLE_CORE
        3. 35.4.2.3 UART Loopback with Interrupt - SINGLE_CORE
        4. 35.4.2.4 UART Loopback with DMA - SINGLE_CORE
        5. 35.4.2.5 UART Echoback - SINGLE_CORE
    5. 35.5 UART Registers
      1. 35.5.1 UART Base Address Table
      2. 35.5.2 UART_REGS Registers
      3. 35.5.3 UART_REGS_WRITE Registers
  42. 36Local Interconnect Network (LIN)
    1. 36.1 LIN Overview
      1. 36.1.1 LIN Mode Features
      2. 36.1.2 SCI Mode Features
      3. 36.1.3 Block Diagram
    2. 36.2 Serial Communications Interface Module
      1. 36.2.1 SCI Communication Formats
        1. 36.2.1.1 SCI Frame Formats
        2. 36.2.1.2 SCI Asynchronous Timing Mode
        3. 36.2.1.3 SCI Baud Rate
          1. 36.2.1.3.1 Superfractional Divider, SCI Asynchronous Mode
        4. 36.2.1.4 SCI Multiprocessor Communication Modes
          1. 36.2.1.4.1 Idle-Line Multiprocessor Modes
          2. 36.2.1.4.2 Address-Bit Multiprocessor Mode
        5. 36.2.1.5 SCI Multibuffered Mode
      2. 36.2.2 SCI Interrupts
        1. 36.2.2.1 Transmit Interrupt
        2. 36.2.2.2 Receive Interrupt
        3. 36.2.2.3 WakeUp Interrupt
        4. 36.2.2.4 Error Interrupts
      3. 36.2.3 SCI RTDMA Interface
        1. 36.2.3.1 Receive RTDMA Requests
        2. 36.2.3.2 Transmit RTDMA Requests
      4. 36.2.4 SCI Configurations
        1. 36.2.4.1 Receiving Data
          1. 36.2.4.1.1 Receiving Data in Single-Buffer Mode
          2. 36.2.4.1.2 Receiving Data in Multibuffer Mode
        2. 36.2.4.2 Transmitting Data
          1. 36.2.4.2.1 Transmitting Data in Single-Buffer Mode
          2. 36.2.4.2.2 Transmitting Data in Multibuffer Mode
      5. 36.2.5 SCI Low-Power Mode
        1. 36.2.5.1 Sleep Mode for Multiprocessor Communication
    3. 36.3 Local Interconnect Network Module
      1. 36.3.1 LIN Communication Formats
        1. 36.3.1.1  LIN Standards
        2. 36.3.1.2  Message Frame
          1. 36.3.1.2.1 Message Header
          2. 36.3.1.2.2 Response
        3. 36.3.1.3  Synchronizer
        4. 36.3.1.4  Baud Rate
          1. 36.3.1.4.1 Fractional Divider
          2. 36.3.1.4.2 Superfractional Divider
            1. 36.3.1.4.2.1 Superfractional Divider In LIN Mode
        5. 36.3.1.5  Header Generation
          1. 36.3.1.5.1 Event Triggered Frame Handling
          2. 36.3.1.5.2 Header Reception and Adaptive Baud Rate
        6. 36.3.1.6  Extended Frames Handling
        7. 36.3.1.7  Timeout Control
          1. 36.3.1.7.1 No-Response Error (NRE)
          2. 36.3.1.7.2 Bus Idle Detection
          3. 36.3.1.7.3 Timeout After Wakeup Signal and Timeout After Three Wakeup Signals
        8. 36.3.1.8  TXRX Error Detector (TED)
          1. 36.3.1.8.1 Bit Errors
          2. 36.3.1.8.2 Physical Bus Errors
          3. 36.3.1.8.3 ID Parity Errors
          4. 36.3.1.8.4 Checksum Errors
        9. 36.3.1.9  Message Filtering and Validation
        10. 36.3.1.10 Receive Buffers
        11. 36.3.1.11 Transmit Buffers
      2. 36.3.2 LIN Interrupts
      3. 36.3.3 Servicing LIN Interrupts
      4. 36.3.4 LIN RTDMA Interface
        1. 36.3.4.1 LIN Receive RTDMA Requests
        2. 36.3.4.2 LIN Transmit RTDMA Requests
      5. 36.3.5 LIN Configurations
        1. 36.3.5.1 Receiving Data
          1. 36.3.5.1.1 Receiving Data in Single-Buffer Mode
          2. 36.3.5.1.2 Receiving Data in Multibuffer Mode
        2. 36.3.5.2 Transmitting Data
          1. 36.3.5.2.1 Transmitting Data in Single-Buffer Mode
          2. 36.3.5.2.2 Transmitting Data in Multibuffer Mode
    4. 36.4 Low-Power Mode
      1. 36.4.1 Entering Sleep Mode
      2. 36.4.2 Wakeup
      3. 36.4.3 Wakeup Timeouts
    5. 36.5 Emulation Mode
    6. 36.6 Software
      1. 36.6.1 LIN Registers to Driverlib Functions
      2. 36.6.2 LIN Examples
        1. 36.6.2.1 LIN Internal Loopback with Interrupts - SINGLE_CORE
        2. 36.6.2.2 LIN SCI Mode Internal Loopback with Interrupts - SINGLE_CORE
        3. 36.6.2.3 LIN SCI MODE Internal Loopback with DMA - SINGLE_CORE
        4. 36.6.2.4 LIN Internal Loopback without interrupts (polled mode) - SINGLE_CORE
        5. 36.6.2.5 LIN SCI MODE (Single Buffer) Internal Loopback with DMA - SINGLE_CORE
    7. 36.7 LIN Registers
      1. 36.7.1 LIN Base Address Table
      2. 36.7.2 LIN_REGS Registers
  43. 37Serial Peripheral Interface (SPI)
    1. 37.1 Introduction
      1. 37.1.1 Features
      2. 37.1.2 Block Diagram
    2. 37.2 System-Level Integration
      1. 37.2.1 SPI Module Signals
      2. 37.2.2 Configuring Device Pins
        1. 37.2.2.1 GPIOs Required for High-Speed Mode
      3. 37.2.3 SPI Interrupts
      4. 37.2.4 RTDMA Support
    3. 37.3 SPI Operation
      1. 37.3.1  Introduction to Operation
      2. 37.3.2  Controller Mode
      3. 37.3.3  Peripheral Mode
      4. 37.3.4  Data Format
        1. 37.3.4.1 Transmission of Bit from SPIRXBUF
      5. 37.3.5  Baud Rate Selection
        1. 37.3.5.1 Baud Rate Determination
        2. 37.3.5.2 Baud Rate Calculation in Non-High Speed Mode (HS_MODE = 0)
        3. 37.3.5.3 Baud Rate Calculation
      6. 37.3.6  SPI Clocking Schemes
      7. 37.3.7  SPI FIFO Description
      8. 37.3.8  SPI RTDMA Transfers
        1. 37.3.8.1 Transmitting Data Using SPI with RTDMA
        2. 37.3.8.2 Receiving Data Using SPI with RTDMA
      9. 37.3.9  SPI High-Speed Mode
      10. 37.3.10 SPI 3-Wire Mode Description
    4. 37.4 Programming Procedure
      1. 37.4.1 Initialization Upon Reset
      2. 37.4.2 Configuring the SPI
      3. 37.4.3 Configuring the SPI for High-Speed Mode
      4. 37.4.4 Data Transfer Example
      5. 37.4.5 SPI 3-Wire Mode Code Examples
        1. 37.4.5.1 3-Wire Controller Mode Transmit
        2.       1753
          1. 37.4.5.2.1 3-Wire Controller Mode Receive
        3.       1755
          1. 37.4.5.2.1 3-Wire Peripheral Mode Transmit
        4.       1757
          1. 37.4.5.2.1 3-Wire Peripheral Mode Receive
      6. 37.4.6 SPI STEINV Bit in Digital Audio Transfers
    5. 37.5 Software
      1. 37.5.1 SPI Registers to Driverlib Functions
      2. 37.5.2 SPI Examples
        1. 37.5.2.1 SPI Digital Loopback - SINGLE_CORE
        2. 37.5.2.2 SPI Digital Loopback with FIFO Interrupts - SINGLE_CORE
        3. 37.5.2.3 SPI Digital External Loopback without FIFO Interrupts - SINGLE_CORE
        4. 37.5.2.4 SPI Digital External Loopback with FIFO Interrupts - SINGLE_CORE
        5. 37.5.2.5 SPI Digital Loopback with DMA - SINGLE_CORE
    6. 37.6 SPI Registers
      1. 37.6.1 SPI Base Address Table
      2. 37.6.2 SPI_REGS Registers
  44. 38Single Edge Nibble Transmission (SENT)
    1. 38.1 Introduction
      1. 38.1.1 Features
      2. 38.1.2 SENT Related Collateral
    2. 38.2 Advanced Topologies: MTPG
      1. 38.2.1 MTPG Features
      2. 38.2.2 MTPG Description
      3. 38.2.3 Channel Triggers
      4. 38.2.4 Timeout
    3. 38.3 Protocol Description
      1. 38.3.1 Nibble Frame Format
      2. 38.3.2 Cyclic Redundancy Check (CRC)
      3. 38.3.3 Short Serial Message Format
      4. 38.3.4 Enhanced Serial Message Format
      5. 38.3.5 Enhanced Serial Message Format CRC
      6. 38.3.6 Receive Modes
    4. 38.4 RTDMA Trigger
    5. 38.5 Interrupts Configuration
    6. 38.6 Glitch Filter
    7. 38.7 Software
      1. 38.7.1 SENT Registers to Driverlib Functions
      2. 38.7.2 SENT Examples
        1. 38.7.2.1 SENT Single Sensor - SINGLE_CORE
    8. 38.8 SENT Registers
      1. 38.8.1 SENT Base Address Table
      2. 38.8.2 SENT_CFG Registers
      3. 38.8.3 SENT_MEM Registers
      4. 38.8.4 SENT_MTPG Registers
  45.   ► SECURITY PERIPHERALS
    1.     Technical Reference Manual Overview
  46. 39Security Modules
    1. 39.1 Hardware Security Module (HSM)
      1. 39.1.1 HSM Related Collateral
    2. 39.2 Cryptographic Accelerators
  47. 40Revision History

2.14.7 SYNCBRIDGEMPU_REGS Registers

Table 2-322 lists the memory-mapped registers for the SYNCBRIDGEMPU_REGS registers. All register offset addresses not listed in Table 2-322 should be considered as reserved locations and the register contents should not be modified.

Table 2-322 SYNCBRIDGEMPU_REGS Registers
OffsetAcronymRegister NameProtection
0hMPUR1_STARTMPU Region 1 Start AddressLOCK: MPUR1_LOCK.LOCK
4hMPUR1_ENDMPU Region 1 End AddressLOCK: MPUR1_LOCK.LOCK
8hMPUR1_LOCKMPU 1 Temporary LockCOMMIT: MPUR1_COMMIT.COMMIT
ChMPUR1_COMMITMPU 1 Permanent Commit
10hMPUR1_ACCESSMPU Region 1 R/W Access PermissionsLOCK: MPUR1_LOCK.LOCK
20hMPUR2_STARTMPU Region 2 Start AddressLOCK: MPUR2_LOCK.LOCK
24hMPUR2_ENDMPU Region 2 End AddressLOCK: MPUR2_LOCK.LOCK
28hMPUR2_LOCKMPU 2 Temporary LockCOMMIT: MPUR2_COMMIT.COMMIT
2ChMPUR2_COMMITMPU 2 Permanent Commit
30hMPUR2_ACCESSMPU Region 2 R/W Access PermissionsLOCK: MPUR2_LOCK.LOCK
40hMPUR3_STARTMPU Region 3 Start AddressLOCK: MPUR3_LOCK.LOCK
44hMPUR3_ENDMPU Region 3 End AddressLOCK: MPUR3_LOCK.LOCK
48hMPUR3_LOCKMPU 3 Temporary LockCOMMIT: MPUR3_COMMIT.COMMIT
4ChMPUR3_COMMITMPU 3 Permanent Commit
50hMPUR3_ACCESSMPU Region 3 R/W Access PermissionsLOCK: MPUR3_LOCK.LOCK
60hMPUR4_STARTMPU Region 4 Start AddressLOCK: MPUR4_LOCK.LOCK
64hMPUR4_ENDMPU Region 4 End AddressLOCK: MPUR4_LOCK.LOCK
68hMPUR4_LOCKMPU 4 Temporary LockCOMMIT: MPUR4_COMMIT.COMMIT
6ChMPUR4_COMMITMPU 4 Permanent Commit
70hMPUR4_ACCESSMPU Region 4 R/W Access PermissionsLOCK: MPUR4_LOCK.LOCK
80hMPUR5_STARTMPU Region 5 Start AddressLOCK: MPUR5_LOCK.LOCK
84hMPUR5_ENDMPU Region 5 End AddressLOCK: MPUR5_LOCK.LOCK
88hMPUR5_LOCKMPU 5 Temporary LockCOMMIT: MPUR5_COMMIT.COMMIT
8ChMPUR5_COMMITMPU 5 Permanent Commit
90hMPUR5_ACCESSMPU Region 5 R/W Access PermissionsLOCK: MPUR5_LOCK.LOCK
A0hMPUR6_STARTMPU Region 6 Start AddressLOCK: MPUR6_LOCK.LOCK
A4hMPUR6_ENDMPU Region 6 End AddressLOCK: MPUR6_LOCK.LOCK
A8hMPUR6_LOCKMPU 6 Temporary LockCOMMIT: MPUR6_COMMIT.COMMIT
AChMPUR6_COMMITMPU 6 Permanent Commit
B0hMPUR6_ACCESSMPU Region 6 R/W Access PermissionsLOCK: MPUR6_LOCK.LOCK
C0hMPUR7_STARTMPU Region 7 Start AddressLOCK: MPUR7_LOCK.LOCK
C4hMPUR7_ENDMPU Region 7 End AddressLOCK: MPUR7_LOCK.LOCK
C8hMPUR7_LOCKMPU 7 Temporary LockCOMMIT: MPUR7_COMMIT.COMMIT
CChMPUR7_COMMITMPU 7 Permanent Commit
D0hMPUR7_ACCESSMPU Region 7 R/W Access PermissionsLOCK: MPUR7_LOCK.LOCK
E0hMPUR8_STARTMPU Region 8 Start AddressLOCK: MPUR8_LOCK.LOCK
E4hMPUR8_ENDMPU Region 8 End AddressLOCK: MPUR8_LOCK.LOCK
E8hMPUR8_LOCKMPU 8 Temporary LockCOMMIT: MPUR8_COMMIT.COMMIT
EChMPUR8_COMMITMPU 8 Permanent Commit
F0hMPUR8_ACCESSMPU Region 8 R/W Access PermissionsLOCK: MPUR8_LOCK.LOCK
100hMPUR9_STARTMPU Region 9 Start AddressLOCK: MPUR9_LOCK.LOCK
104hMPUR9_ENDMPU Region 9 End AddressLOCK: MPUR9_LOCK.LOCK
108hMPUR9_LOCKMPU 9 Temporary LockCOMMIT: MPUR9_COMMIT.COMMIT
10ChMPUR9_COMMITMPU 9 Permanent Commit
110hMPUR9_ACCESSMPU Region 9 R/W Access PermissionsLOCK: MPUR9_LOCK.LOCK
120hMPUR10_STARTMPU Region 10 Start AddressLOCK: MPUR10_LOCK.LOCK
124hMPUR10_ENDMPU Region 10 End AddressLOCK: MPUR10_LOCK.LOCK
128hMPUR10_LOCKMPU 10 Temporary LockCOMMIT: MPUR10_COMMIT.COMMIT
12ChMPUR10_COMMITMPU 10 Permanent Commit
130hMPUR10_ACCESSMPU Region 10 R/W Access PermissionsLOCK: MPUR10_LOCK.LOCK
140hMPUR11_STARTMPU Region 11 Start AddressLOCK: MPUR11_LOCK.LOCK
144hMPUR11_ENDMPU Region 11 End AddressLOCK: MPUR11_LOCK.LOCK
148hMPUR11_LOCKMPU 11 Temporary LockCOMMIT: MPUR11_COMMIT.COMMIT
14ChMPUR11_COMMITMPU 11 Permanent Commit
150hMPUR11_ACCESSMPU Region 11 R/W Access PermissionsLOCK: MPUR11_LOCK.LOCK
160hMPUR12_STARTMPU Region 12 Start AddressLOCK: MPUR12_LOCK.LOCK
164hMPUR12_ENDMPU Region 12 End AddressLOCK: MPUR12_LOCK.LOCK
168hMPUR12_LOCKMPU 12 Temporary LockCOMMIT: MPUR12_COMMIT.COMMIT
16ChMPUR12_COMMITMPU 12 Permanent Commit
170hMPUR12_ACCESSMPU Region 12 R/W Access PermissionsLOCK: MPUR12_LOCK.LOCK
180hMPUR13_STARTMPU Region 13 Start AddressLOCK: MPUR13_LOCK.LOCK
184hMPUR13_ENDMPU Region 13 End AddressLOCK: MPUR13_LOCK.LOCK
188hMPUR13_LOCKMPU 13 Temporary LockCOMMIT: MPUR13_COMMIT.COMMIT
18ChMPUR13_COMMITMPU 13 Permanent Commit
190hMPUR13_ACCESSMPU Region 13 R/W Access PermissionsLOCK: MPUR13_LOCK.LOCK
1A0hMPUR14_STARTMPU Region 14 Start AddressLOCK: MPUR14_LOCK.LOCK
1A4hMPUR14_ENDMPU Region 14 End AddressLOCK: MPUR14_LOCK.LOCK
1A8hMPUR14_LOCKMPU 14 Temporary LockCOMMIT: MPUR14_COMMIT.COMMIT
1AChMPUR14_COMMITMPU 14 Permanent Commit
1B0hMPUR14_ACCESSMPU Region 14 R/W Access PermissionsLOCK: MPUR14_LOCK.LOCK
1C0hMPUR15_STARTMPU Region 15 Start AddressLOCK: MPUR15_LOCK.LOCK
1C4hMPUR15_ENDMPU Region 15 End AddressLOCK: MPUR15_LOCK.LOCK
1C8hMPUR15_LOCKMPU 15 Temporary LockCOMMIT: MPUR15_COMMIT.COMMIT
1CChMPUR15_COMMITMPU 15 Permanent Commit
1D0hMPUR15_ACCESSMPU Region 15 R/W Access PermissionsLOCK: MPUR15_LOCK.LOCK
1E0hMPUR16_STARTMPU Region 16 Start AddressLOCK: MPUR16_LOCK.LOCK
1E4hMPUR16_ENDMPU Region 16 End AddressLOCK: MPUR16_LOCK.LOCK
1E8hMPUR16_LOCKMPU 16 Temporary LockCOMMIT: MPUR16_COMMIT.COMMIT
1EChMPUR16_COMMITMPU 16 Permanent Commit
1F0hMPUR16_ACCESSMPU Region 16 R/W Access PermissionsLOCK: MPUR16_LOCK.LOCK
200hMPUR17_STARTMPU Region 17 Start AddressLOCK: MPUR17_LOCK.LOCK
204hMPUR17_ENDMPU Region 17 End AddressLOCK: MPUR17_LOCK.LOCK
208hMPUR17_LOCKMPU 17 Temporary LockCOMMIT: MPUR17_COMMIT.COMMIT
20ChMPUR17_COMMITMPU 17 Permanent Commit
210hMPUR17_ACCESSMPU Region 17 R/W Access PermissionsLOCK: MPUR17_LOCK.LOCK
220hMPUR18_STARTMPU Region 18 Start AddressLOCK: MPUR18_LOCK.LOCK
224hMPUR18_ENDMPU Region 18 End AddressLOCK: MPUR18_LOCK.LOCK
228hMPUR18_LOCKMPU 18 Temporary LockCOMMIT: MPUR18_COMMIT.COMMIT
22ChMPUR18_COMMITMPU 18 Permanent Commit
230hMPUR18_ACCESSMPU Region 18 R/W Access PermissionsLOCK: MPUR18_LOCK.LOCK
240hMPUR19_STARTMPU Region 19 Start AddressLOCK: MPUR19_LOCK.LOCK
244hMPUR19_ENDMPU Region 19 End AddressLOCK: MPUR19_LOCK.LOCK
248hMPUR19_LOCKMPU 19 Temporary LockCOMMIT: MPUR19_COMMIT.COMMIT
24ChMPUR19_COMMITMPU 19 Permanent Commit
250hMPUR19_ACCESSMPU Region 19 R/W Access PermissionsLOCK: MPUR19_LOCK.LOCK
260hMPUR20_STARTMPU Region 20 Start AddressLOCK: MPUR20_LOCK.LOCK
264hMPUR20_ENDMPU Region 20 End AddressLOCK: MPUR20_LOCK.LOCK
268hMPUR20_LOCKMPU 20 Temporary LockCOMMIT: MPUR20_COMMIT.COMMIT
26ChMPUR20_COMMITMPU 20 Permanent Commit
270hMPUR20_ACCESSMPU Region 20 R/W Access PermissionsLOCK: MPUR20_LOCK.LOCK
280hMPUR21_STARTMPU Region 21 Start AddressLOCK: MPUR21_LOCK.LOCK
284hMPUR21_ENDMPU Region 21 End AddressLOCK: MPUR21_LOCK.LOCK
288hMPUR21_LOCKMPU 21 Temporary LockCOMMIT: MPUR21_COMMIT.COMMIT
28ChMPUR21_COMMITMPU 21 Permanent Commit
290hMPUR21_ACCESSMPU Region 21 R/W Access PermissionsLOCK: MPUR21_LOCK.LOCK
2A0hMPUR22_STARTMPU Region 22 Start AddressLOCK: MPUR22_LOCK.LOCK
2A4hMPUR22_ENDMPU Region 22 End AddressLOCK: MPUR22_LOCK.LOCK
2A8hMPUR22_LOCKMPU 22 Temporary LockCOMMIT: MPUR22_COMMIT.COMMIT
2AChMPUR22_COMMITMPU 22 Permanent Commit
2B0hMPUR22_ACCESSMPU Region 22 R/W Access PermissionsLOCK: MPUR22_LOCK.LOCK
2C0hMPUR23_STARTMPU Region 23 Start AddressLOCK: MPUR23_LOCK.LOCK
2C4hMPUR23_ENDMPU Region 23 End AddressLOCK: MPUR23_LOCK.LOCK
2C8hMPUR23_LOCKMPU 23 Temporary LockCOMMIT: MPUR23_COMMIT.COMMIT
2CChMPUR23_COMMITMPU 23 Permanent Commit
2D0hMPUR23_ACCESSMPU Region 23 R/W Access PermissionsLOCK: MPUR23_LOCK.LOCK
2E0hMPUR24_STARTMPU Region 24 Start AddressLOCK: MPUR24_LOCK.LOCK
2E4hMPUR24_ENDMPU Region 24 End AddressLOCK: MPUR24_LOCK.LOCK
2E8hMPUR24_LOCKMPU 24 Temporary LockCOMMIT: MPUR24_COMMIT.COMMIT
2EChMPUR24_COMMITMPU 24 Permanent Commit
2F0hMPUR24_ACCESSMPU Region 24 R/W Access PermissionsLOCK: MPUR24_LOCK.LOCK
300hMPUR25_STARTMPU Region 25 Start AddressLOCK: MPUR25_LOCK.LOCK
304hMPUR25_ENDMPU Region 25 End AddressLOCK: MPUR25_LOCK.LOCK
308hMPUR25_LOCKMPU 25 Temporary LockCOMMIT: MPUR25_COMMIT.COMMIT
30ChMPUR25_COMMITMPU 25 Permanent Commit
310hMPUR25_ACCESSMPU Region 25 R/W Access PermissionsLOCK: MPUR25_LOCK.LOCK
320hMPUR26_STARTMPU Region 26 Start AddressLOCK: MPUR26_LOCK.LOCK
324hMPUR26_ENDMPU Region 26 End AddressLOCK: MPUR26_LOCK.LOCK
328hMPUR26_LOCKMPU 26 Temporary LockCOMMIT: MPUR26_COMMIT.COMMIT
32ChMPUR26_COMMITMPU 26 Permanent Commit
330hMPUR26_ACCESSMPU Region 26 R/W Access PermissionsLOCK: MPUR26_LOCK.LOCK
340hMPUR27_STARTMPU Region 27 Start AddressLOCK: MPUR27_LOCK.LOCK
344hMPUR27_ENDMPU Region 27 End AddressLOCK: MPUR27_LOCK.LOCK
348hMPUR27_LOCKMPU 27 Temporary LockCOMMIT: MPUR27_COMMIT.COMMIT
34ChMPUR27_COMMITMPU 27 Permanent Commit
350hMPUR27_ACCESSMPU Region 27 R/W Access PermissionsLOCK: MPUR27_LOCK.LOCK
360hMPUR28_STARTMPU Region 28 Start AddressLOCK: MPUR28_LOCK.LOCK
364hMPUR28_ENDMPU Region 28 End AddressLOCK: MPUR28_LOCK.LOCK
368hMPUR28_LOCKMPU 28 Temporary LockCOMMIT: MPUR28_COMMIT.COMMIT
36ChMPUR28_COMMITMPU 28 Permanent Commit
370hMPUR28_ACCESSMPU Region 28 R/W Access PermissionsLOCK: MPUR28_LOCK.LOCK
380hMPUR29_STARTMPU Region 29 Start AddressLOCK: MPUR29_LOCK.LOCK
384hMPUR29_ENDMPU Region 29 End AddressLOCK: MPUR29_LOCK.LOCK
388hMPUR29_LOCKMPU 29 Temporary LockCOMMIT: MPUR29_COMMIT.COMMIT
38ChMPUR29_COMMITMPU 29 Permanent Commit
390hMPUR29_ACCESSMPU Region 29 R/W Access PermissionsLOCK: MPUR29_LOCK.LOCK
3A0hMPUR30_STARTMPU Region 30 Start AddressLOCK: MPUR30_LOCK.LOCK
3A4hMPUR30_ENDMPU Region 30 End AddressLOCK: MPUR30_LOCK.LOCK
3A8hMPUR30_LOCKMPU 30 Temporary LockCOMMIT: MPUR30_COMMIT.COMMIT
3AChMPUR30_COMMITMPU 30 Permanent Commit
3B0hMPUR30_ACCESSMPU Region 30 R/W Access PermissionsLOCK: MPUR30_LOCK.LOCK
3C0hMPUR31_STARTMPU Region 31 Start AddressLOCK: MPUR31_LOCK.LOCK
3C4hMPUR31_ENDMPU Region 31 End AddressLOCK: MPUR31_LOCK.LOCK
3C8hMPUR31_LOCKMPU 31 Temporary LockCOMMIT: MPUR31_COMMIT.COMMIT
3CChMPUR31_COMMITMPU 31 Permanent Commit
3D0hMPUR31_ACCESSMPU Region 31 R/W Access PermissionsLOCK: MPUR31_LOCK.LOCK
3E0hMPUR32_STARTMPU Region 32 Start AddressLOCK: MPUR32_LOCK.LOCK
3E4hMPUR32_ENDMPU Region 32 End AddressLOCK: MPUR32_LOCK.LOCK
3E8hMPUR32_LOCKMPU 32 Temporary LockCOMMIT: MPUR32_COMMIT.COMMIT
3EChMPUR32_COMMITMPU 32 Permanent Commit
3F0hMPUR32_ACCESSMPU Region 32 R/W Access PermissionsLOCK: MPUR32_LOCK.LOCK
800hMPUCTRLMPU Control RegisterLOCK: MPUCFG_LOCK.LOCK
820hMPUCFG_LOCKChannel Configuration Temporary LockCOMMIT: MPUCFG_COMMIT.COMMIT
824hMPUCFG_COMMITChannel Configuration Permanent Commit

Complex bit access types are encoded to fit into small table cells. Table 2-323 shows the codes that are used for access types in this section.

Table 2-323 SYNCBRIDGEMPU_REGS Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
Write Type
WWWrite
W1SW
1S		Write
1 to set
Reset or Default Value
-nValue after reset or the default value
Register Array Variables
i,j,k,l,m,nWhen these variables are used in a register name, an offset, or an address, they refer to the value of a register array where the register is part of a group of repeating registers. The register groups form a hierarchical structure and the array is represented with a formula.
yWhen this variable is used in a register name, an offset, or an address it refers to the value of a register array.

3.14.7.1 MPUR1_START Register (Offset = 0h) [Reset = 00000000h]

MPUR1_START is shown in Figure 2-322 and described in Table 2-324.

Return to the Summary Table.

MPU Region 1 Start Address

Figure 2-322 MPUR1_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-324 MPUR1_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.2 MPUR1_END Register (Offset = 4h) [Reset = 00000000h]

MPUR1_END is shown in Figure 2-323 and described in Table 2-325.

Return to the Summary Table.

MPU Region 1 End Address

Figure 2-323 MPUR1_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-325 MPUR1_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.3 MPUR1_LOCK Register (Offset = 8h) [Reset = 00000000h]

MPUR1_LOCK is shown in Figure 2-324 and described in Table 2-326.

Return to the Summary Table.

MPU 1 Temporary Lock

Figure 2-324 MPUR1_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-326 MPUR1_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.4 MPUR1_COMMIT Register (Offset = Ch) [Reset = 00000000h]

MPUR1_COMMIT is shown in Figure 2-325 and described in Table 2-327.

Return to the Summary Table.

MPU 1 Permanent Commit

Figure 2-325 MPUR1_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-327 MPUR1_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.5 MPUR1_ACCESS Register (Offset = 10h) [Reset = 00000000h]

MPUR1_ACCESS is shown in Figure 2-326 and described in Table 2-328.

Return to the Summary Table.

MPU Region 1 R/W Access Permissions

Figure 2-326 MPUR1_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-328 MPUR1_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.6 MPUR2_START Register (Offset = 20h) [Reset = 00000000h]

MPUR2_START is shown in Figure 2-327 and described in Table 2-329.

Return to the Summary Table.

MPU Region 2 Start Address

Figure 2-327 MPUR2_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-329 MPUR2_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.7 MPUR2_END Register (Offset = 24h) [Reset = 00000000h]

MPUR2_END is shown in Figure 2-328 and described in Table 2-330.

Return to the Summary Table.

MPU Region 2 End Address

Figure 2-328 MPUR2_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-330 MPUR2_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.8 MPUR2_LOCK Register (Offset = 28h) [Reset = 00000000h]

MPUR2_LOCK is shown in Figure 2-329 and described in Table 2-331.

Return to the Summary Table.

MPU 2 Temporary Lock

Figure 2-329 MPUR2_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-331 MPUR2_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.9 MPUR2_COMMIT Register (Offset = 2Ch) [Reset = 00000000h]

MPUR2_COMMIT is shown in Figure 2-330 and described in Table 2-332.

Return to the Summary Table.

MPU 2 Permanent Commit

Figure 2-330 MPUR2_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-332 MPUR2_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.10 MPUR2_ACCESS Register (Offset = 30h) [Reset = 00000000h]

MPUR2_ACCESS is shown in Figure 2-331 and described in Table 2-333.

Return to the Summary Table.

MPU Region 2 R/W Access Permissions

Figure 2-331 MPUR2_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-333 MPUR2_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.11 MPUR3_START Register (Offset = 40h) [Reset = 00000000h]

MPUR3_START is shown in Figure 2-332 and described in Table 2-334.

Return to the Summary Table.

MPU Region 3 Start Address

Figure 2-332 MPUR3_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-334 MPUR3_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.12 MPUR3_END Register (Offset = 44h) [Reset = 00000000h]

MPUR3_END is shown in Figure 2-333 and described in Table 2-335.

Return to the Summary Table.

MPU Region 3 End Address

Figure 2-333 MPUR3_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-335 MPUR3_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.13 MPUR3_LOCK Register (Offset = 48h) [Reset = 00000000h]

MPUR3_LOCK is shown in Figure 2-334 and described in Table 2-336.

Return to the Summary Table.

MPU 3 Temporary Lock

Figure 2-334 MPUR3_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-336 MPUR3_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.14 MPUR3_COMMIT Register (Offset = 4Ch) [Reset = 00000000h]

MPUR3_COMMIT is shown in Figure 2-335 and described in Table 2-337.

Return to the Summary Table.

MPU 3 Permanent Commit

Figure 2-335 MPUR3_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-337 MPUR3_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.15 MPUR3_ACCESS Register (Offset = 50h) [Reset = 00000000h]

MPUR3_ACCESS is shown in Figure 2-336 and described in Table 2-338.

Return to the Summary Table.

MPU Region 3 R/W Access Permissions

Figure 2-336 MPUR3_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-338 MPUR3_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.16 MPUR4_START Register (Offset = 60h) [Reset = 00000000h]

MPUR4_START is shown in Figure 2-337 and described in Table 2-339.

Return to the Summary Table.

MPU Region 4 Start Address

Figure 2-337 MPUR4_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-339 MPUR4_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.17 MPUR4_END Register (Offset = 64h) [Reset = 00000000h]

MPUR4_END is shown in Figure 2-338 and described in Table 2-340.

Return to the Summary Table.

MPU Region 4 End Address

Figure 2-338 MPUR4_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-340 MPUR4_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.18 MPUR4_LOCK Register (Offset = 68h) [Reset = 00000000h]

MPUR4_LOCK is shown in Figure 2-339 and described in Table 2-341.

Return to the Summary Table.

MPU 4 Temporary Lock

Figure 2-339 MPUR4_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-341 MPUR4_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.19 MPUR4_COMMIT Register (Offset = 6Ch) [Reset = 00000000h]

MPUR4_COMMIT is shown in Figure 2-340 and described in Table 2-342.

Return to the Summary Table.

MPU 4 Permanent Commit

Figure 2-340 MPUR4_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-342 MPUR4_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.20 MPUR4_ACCESS Register (Offset = 70h) [Reset = 00000000h]

MPUR4_ACCESS is shown in Figure 2-341 and described in Table 2-343.

Return to the Summary Table.

MPU Region 4 R/W Access Permissions

Figure 2-341 MPUR4_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-343 MPUR4_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.21 MPUR5_START Register (Offset = 80h) [Reset = 00000000h]

MPUR5_START is shown in Figure 2-342 and described in Table 2-344.

Return to the Summary Table.

MPU Region 5 Start Address

Figure 2-342 MPUR5_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-344 MPUR5_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.22 MPUR5_END Register (Offset = 84h) [Reset = 00000000h]

MPUR5_END is shown in Figure 2-343 and described in Table 2-345.

Return to the Summary Table.

MPU Region 5 End Address

Figure 2-343 MPUR5_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-345 MPUR5_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.23 MPUR5_LOCK Register (Offset = 88h) [Reset = 00000000h]

MPUR5_LOCK is shown in Figure 2-344 and described in Table 2-346.

Return to the Summary Table.

MPU 5 Temporary Lock

Figure 2-344 MPUR5_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-346 MPUR5_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.24 MPUR5_COMMIT Register (Offset = 8Ch) [Reset = 00000000h]

MPUR5_COMMIT is shown in Figure 2-345 and described in Table 2-347.

Return to the Summary Table.

MPU 5 Permanent Commit

Figure 2-345 MPUR5_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-347 MPUR5_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.25 MPUR5_ACCESS Register (Offset = 90h) [Reset = 00000000h]

MPUR5_ACCESS is shown in Figure 2-346 and described in Table 2-348.

Return to the Summary Table.

MPU Region 5 R/W Access Permissions

Figure 2-346 MPUR5_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-348 MPUR5_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.26 MPUR6_START Register (Offset = A0h) [Reset = 00000000h]

MPUR6_START is shown in Figure 2-347 and described in Table 2-349.

Return to the Summary Table.

MPU Region 6 Start Address

Figure 2-347 MPUR6_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-349 MPUR6_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.27 MPUR6_END Register (Offset = A4h) [Reset = 00000000h]

MPUR6_END is shown in Figure 2-348 and described in Table 2-350.

Return to the Summary Table.

MPU Region 6 End Address

Figure 2-348 MPUR6_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-350 MPUR6_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.28 MPUR6_LOCK Register (Offset = A8h) [Reset = 00000000h]

MPUR6_LOCK is shown in Figure 2-349 and described in Table 2-351.

Return to the Summary Table.

MPU 6 Temporary Lock

Figure 2-349 MPUR6_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-351 MPUR6_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.29 MPUR6_COMMIT Register (Offset = ACh) [Reset = 00000000h]

MPUR6_COMMIT is shown in Figure 2-350 and described in Table 2-352.

Return to the Summary Table.

MPU 6 Permanent Commit

Figure 2-350 MPUR6_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-352 MPUR6_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.30 MPUR6_ACCESS Register (Offset = B0h) [Reset = 00000000h]

MPUR6_ACCESS is shown in Figure 2-351 and described in Table 2-353.

Return to the Summary Table.

MPU Region 6 R/W Access Permissions

Figure 2-351 MPUR6_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-353 MPUR6_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.31 MPUR7_START Register (Offset = C0h) [Reset = 00000000h]

MPUR7_START is shown in Figure 2-352 and described in Table 2-354.

Return to the Summary Table.

MPU Region 7 Start Address

Figure 2-352 MPUR7_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-354 MPUR7_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.32 MPUR7_END Register (Offset = C4h) [Reset = 00000000h]

MPUR7_END is shown in Figure 2-353 and described in Table 2-355.

Return to the Summary Table.

MPU Region 7 End Address

Figure 2-353 MPUR7_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-355 MPUR7_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.33 MPUR7_LOCK Register (Offset = C8h) [Reset = 00000000h]

MPUR7_LOCK is shown in Figure 2-354 and described in Table 2-356.

Return to the Summary Table.

MPU 7 Temporary Lock

Figure 2-354 MPUR7_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-356 MPUR7_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.34 MPUR7_COMMIT Register (Offset = CCh) [Reset = 00000000h]

MPUR7_COMMIT is shown in Figure 2-355 and described in Table 2-357.

Return to the Summary Table.

MPU 7 Permanent Commit

Figure 2-355 MPUR7_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-357 MPUR7_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.35 MPUR7_ACCESS Register (Offset = D0h) [Reset = 00000000h]

MPUR7_ACCESS is shown in Figure 2-356 and described in Table 2-358.

Return to the Summary Table.

MPU Region 7 R/W Access Permissions

Figure 2-356 MPUR7_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-358 MPUR7_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.36 MPUR8_START Register (Offset = E0h) [Reset = 00000000h]

MPUR8_START is shown in Figure 2-357 and described in Table 2-359.

Return to the Summary Table.

MPU Region 8 Start Address

Figure 2-357 MPUR8_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-359 MPUR8_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.37 MPUR8_END Register (Offset = E4h) [Reset = 00000000h]

MPUR8_END is shown in Figure 2-358 and described in Table 2-360.

Return to the Summary Table.

MPU Region 8 End Address

Figure 2-358 MPUR8_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-360 MPUR8_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.38 MPUR8_LOCK Register (Offset = E8h) [Reset = 00000000h]

MPUR8_LOCK is shown in Figure 2-359 and described in Table 2-361.

Return to the Summary Table.

MPU 8 Temporary Lock

Figure 2-359 MPUR8_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-361 MPUR8_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.39 MPUR8_COMMIT Register (Offset = ECh) [Reset = 00000000h]

MPUR8_COMMIT is shown in Figure 2-360 and described in Table 2-362.

Return to the Summary Table.

MPU 8 Permanent Commit

Figure 2-360 MPUR8_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-362 MPUR8_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.40 MPUR8_ACCESS Register (Offset = F0h) [Reset = 00000000h]

MPUR8_ACCESS is shown in Figure 2-361 and described in Table 2-363.

Return to the Summary Table.

MPU Region 8 R/W Access Permissions

Figure 2-361 MPUR8_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-363 MPUR8_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.41 MPUR9_START Register (Offset = 100h) [Reset = 00000000h]

MPUR9_START is shown in Figure 2-362 and described in Table 2-364.

Return to the Summary Table.

MPU Region 9 Start Address

Figure 2-362 MPUR9_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-364 MPUR9_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.42 MPUR9_END Register (Offset = 104h) [Reset = 00000000h]

MPUR9_END is shown in Figure 2-363 and described in Table 2-365.

Return to the Summary Table.

MPU Region 9 End Address

Figure 2-363 MPUR9_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-365 MPUR9_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.43 MPUR9_LOCK Register (Offset = 108h) [Reset = 00000000h]

MPUR9_LOCK is shown in Figure 2-364 and described in Table 2-366.

Return to the Summary Table.

MPU 9 Temporary Lock

Figure 2-364 MPUR9_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-366 MPUR9_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.44 MPUR9_COMMIT Register (Offset = 10Ch) [Reset = 00000000h]

MPUR9_COMMIT is shown in Figure 2-365 and described in Table 2-367.

Return to the Summary Table.

MPU 9 Permanent Commit

Figure 2-365 MPUR9_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-367 MPUR9_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.45 MPUR9_ACCESS Register (Offset = 110h) [Reset = 00000000h]

MPUR9_ACCESS is shown in Figure 2-366 and described in Table 2-368.

Return to the Summary Table.

MPU Region 9 R/W Access Permissions

Figure 2-366 MPUR9_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-368 MPUR9_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.46 MPUR10_START Register (Offset = 120h) [Reset = 00000000h]

MPUR10_START is shown in Figure 2-367 and described in Table 2-369.

Return to the Summary Table.

MPU Region 10 Start Address

Figure 2-367 MPUR10_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-369 MPUR10_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.47 MPUR10_END Register (Offset = 124h) [Reset = 00000000h]

MPUR10_END is shown in Figure 2-368 and described in Table 2-370.

Return to the Summary Table.

MPU Region 10 End Address

Figure 2-368 MPUR10_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-370 MPUR10_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.48 MPUR10_LOCK Register (Offset = 128h) [Reset = 00000000h]

MPUR10_LOCK is shown in Figure 2-369 and described in Table 2-371.

Return to the Summary Table.

MPU 10 Temporary Lock

Figure 2-369 MPUR10_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-371 MPUR10_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.49 MPUR10_COMMIT Register (Offset = 12Ch) [Reset = 00000000h]

MPUR10_COMMIT is shown in Figure 2-370 and described in Table 2-372.

Return to the Summary Table.

MPU 10 Permanent Commit

Figure 2-370 MPUR10_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-372 MPUR10_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.50 MPUR10_ACCESS Register (Offset = 130h) [Reset = 00000000h]

MPUR10_ACCESS is shown in Figure 2-371 and described in Table 2-373.

Return to the Summary Table.

MPU Region 10 R/W Access Permissions

Figure 2-371 MPUR10_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-373 MPUR10_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.51 MPUR11_START Register (Offset = 140h) [Reset = 00000000h]

MPUR11_START is shown in Figure 2-372 and described in Table 2-374.

Return to the Summary Table.

MPU Region 11 Start Address

Figure 2-372 MPUR11_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-374 MPUR11_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.52 MPUR11_END Register (Offset = 144h) [Reset = 00000000h]

MPUR11_END is shown in Figure 2-373 and described in Table 2-375.

Return to the Summary Table.

MPU Region 11 End Address

Figure 2-373 MPUR11_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-375 MPUR11_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.53 MPUR11_LOCK Register (Offset = 148h) [Reset = 00000000h]

MPUR11_LOCK is shown in Figure 2-374 and described in Table 2-376.

Return to the Summary Table.

MPU 11 Temporary Lock

Figure 2-374 MPUR11_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-376 MPUR11_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.54 MPUR11_COMMIT Register (Offset = 14Ch) [Reset = 00000000h]

MPUR11_COMMIT is shown in Figure 2-375 and described in Table 2-377.

Return to the Summary Table.

MPU 11 Permanent Commit

Figure 2-375 MPUR11_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-377 MPUR11_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.55 MPUR11_ACCESS Register (Offset = 150h) [Reset = 00000000h]

MPUR11_ACCESS is shown in Figure 2-376 and described in Table 2-378.

Return to the Summary Table.

MPU Region 11 R/W Access Permissions

Figure 2-376 MPUR11_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-378 MPUR11_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.56 MPUR12_START Register (Offset = 160h) [Reset = 00000000h]

MPUR12_START is shown in Figure 2-377 and described in Table 2-379.

Return to the Summary Table.

MPU Region 12 Start Address

Figure 2-377 MPUR12_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-379 MPUR12_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.57 MPUR12_END Register (Offset = 164h) [Reset = 00000000h]

MPUR12_END is shown in Figure 2-378 and described in Table 2-380.

Return to the Summary Table.

MPU Region 12 End Address

Figure 2-378 MPUR12_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-380 MPUR12_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.58 MPUR12_LOCK Register (Offset = 168h) [Reset = 00000000h]

MPUR12_LOCK is shown in Figure 2-379 and described in Table 2-381.

Return to the Summary Table.

MPU 12 Temporary Lock

Figure 2-379 MPUR12_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-381 MPUR12_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.59 MPUR12_COMMIT Register (Offset = 16Ch) [Reset = 00000000h]

MPUR12_COMMIT is shown in Figure 2-380 and described in Table 2-382.

Return to the Summary Table.

MPU 12 Permanent Commit

Figure 2-380 MPUR12_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-382 MPUR12_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.60 MPUR12_ACCESS Register (Offset = 170h) [Reset = 00000000h]

MPUR12_ACCESS is shown in Figure 2-381 and described in Table 2-383.

Return to the Summary Table.

MPU Region 12 R/W Access Permissions

Figure 2-381 MPUR12_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-383 MPUR12_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.61 MPUR13_START Register (Offset = 180h) [Reset = 00000000h]

MPUR13_START is shown in Figure 2-382 and described in Table 2-384.

Return to the Summary Table.

MPU Region 13 Start Address

Figure 2-382 MPUR13_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-384 MPUR13_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.62 MPUR13_END Register (Offset = 184h) [Reset = 00000000h]

MPUR13_END is shown in Figure 2-383 and described in Table 2-385.

Return to the Summary Table.

MPU Region 13 End Address

Figure 2-383 MPUR13_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-385 MPUR13_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.63 MPUR13_LOCK Register (Offset = 188h) [Reset = 00000000h]

MPUR13_LOCK is shown in Figure 2-384 and described in Table 2-386.

Return to the Summary Table.

MPU 13 Temporary Lock

Figure 2-384 MPUR13_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-386 MPUR13_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.64 MPUR13_COMMIT Register (Offset = 18Ch) [Reset = 00000000h]

MPUR13_COMMIT is shown in Figure 2-385 and described in Table 2-387.

Return to the Summary Table.

MPU 13 Permanent Commit

Figure 2-385 MPUR13_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-387 MPUR13_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.65 MPUR13_ACCESS Register (Offset = 190h) [Reset = 00000000h]

MPUR13_ACCESS is shown in Figure 2-386 and described in Table 2-388.

Return to the Summary Table.

MPU Region 13 R/W Access Permissions

Figure 2-386 MPUR13_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-388 MPUR13_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.66 MPUR14_START Register (Offset = 1A0h) [Reset = 00000000h]

MPUR14_START is shown in Figure 2-387 and described in Table 2-389.

Return to the Summary Table.

MPU Region 14 Start Address

Figure 2-387 MPUR14_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-389 MPUR14_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.67 MPUR14_END Register (Offset = 1A4h) [Reset = 00000000h]

MPUR14_END is shown in Figure 2-388 and described in Table 2-390.

Return to the Summary Table.

MPU Region 14 End Address

Figure 2-388 MPUR14_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-390 MPUR14_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.68 MPUR14_LOCK Register (Offset = 1A8h) [Reset = 00000000h]

MPUR14_LOCK is shown in Figure 2-389 and described in Table 2-391.

Return to the Summary Table.

MPU 14 Temporary Lock

Figure 2-389 MPUR14_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-391 MPUR14_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.69 MPUR14_COMMIT Register (Offset = 1ACh) [Reset = 00000000h]

MPUR14_COMMIT is shown in Figure 2-390 and described in Table 2-392.

Return to the Summary Table.

MPU 14 Permanent Commit

Figure 2-390 MPUR14_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-392 MPUR14_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.70 MPUR14_ACCESS Register (Offset = 1B0h) [Reset = 00000000h]

MPUR14_ACCESS is shown in Figure 2-391 and described in Table 2-393.

Return to the Summary Table.

MPU Region 14 R/W Access Permissions

Figure 2-391 MPUR14_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-393 MPUR14_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.71 MPUR15_START Register (Offset = 1C0h) [Reset = 00000000h]

MPUR15_START is shown in Figure 2-392 and described in Table 2-394.

Return to the Summary Table.

MPU Region 15 Start Address

Figure 2-392 MPUR15_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-394 MPUR15_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.72 MPUR15_END Register (Offset = 1C4h) [Reset = 00000000h]

MPUR15_END is shown in Figure 2-393 and described in Table 2-395.

Return to the Summary Table.

MPU Region 15 End Address

Figure 2-393 MPUR15_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-395 MPUR15_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.73 MPUR15_LOCK Register (Offset = 1C8h) [Reset = 00000000h]

MPUR15_LOCK is shown in Figure 2-394 and described in Table 2-396.

Return to the Summary Table.

MPU 15 Temporary Lock

Figure 2-394 MPUR15_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-396 MPUR15_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.74 MPUR15_COMMIT Register (Offset = 1CCh) [Reset = 00000000h]

MPUR15_COMMIT is shown in Figure 2-395 and described in Table 2-397.

Return to the Summary Table.

MPU 15 Permanent Commit

Figure 2-395 MPUR15_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-397 MPUR15_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.75 MPUR15_ACCESS Register (Offset = 1D0h) [Reset = 00000000h]

MPUR15_ACCESS is shown in Figure 2-396 and described in Table 2-398.

Return to the Summary Table.

MPU Region 15 R/W Access Permissions

Figure 2-396 MPUR15_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-398 MPUR15_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.76 MPUR16_START Register (Offset = 1E0h) [Reset = 00000000h]

MPUR16_START is shown in Figure 2-397 and described in Table 2-399.

Return to the Summary Table.

MPU Region 16 Start Address

Figure 2-397 MPUR16_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-399 MPUR16_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.77 MPUR16_END Register (Offset = 1E4h) [Reset = 00000000h]

MPUR16_END is shown in Figure 2-398 and described in Table 2-400.

Return to the Summary Table.

MPU Region 16 End Address

Figure 2-398 MPUR16_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-400 MPUR16_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.78 MPUR16_LOCK Register (Offset = 1E8h) [Reset = 00000000h]

MPUR16_LOCK is shown in Figure 2-399 and described in Table 2-401.

Return to the Summary Table.

MPU 16 Temporary Lock

Figure 2-399 MPUR16_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-401 MPUR16_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.79 MPUR16_COMMIT Register (Offset = 1ECh) [Reset = 00000000h]

MPUR16_COMMIT is shown in Figure 2-400 and described in Table 2-402.

Return to the Summary Table.

MPU 16 Permanent Commit

Figure 2-400 MPUR16_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-402 MPUR16_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.80 MPUR16_ACCESS Register (Offset = 1F0h) [Reset = 00000000h]

MPUR16_ACCESS is shown in Figure 2-401 and described in Table 2-403.

Return to the Summary Table.

MPU Region 16 R/W Access Permissions

Figure 2-401 MPUR16_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-403 MPUR16_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.81 MPUR17_START Register (Offset = 200h) [Reset = 00000000h]

MPUR17_START is shown in Figure 2-402 and described in Table 2-404.

Return to the Summary Table.

MPU Region 17 Start Address

Figure 2-402 MPUR17_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-404 MPUR17_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.82 MPUR17_END Register (Offset = 204h) [Reset = 00000000h]

MPUR17_END is shown in Figure 2-403 and described in Table 2-405.

Return to the Summary Table.

MPU Region 17 End Address

Figure 2-403 MPUR17_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-405 MPUR17_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.83 MPUR17_LOCK Register (Offset = 208h) [Reset = 00000000h]

MPUR17_LOCK is shown in Figure 2-404 and described in Table 2-406.

Return to the Summary Table.

MPU 17 Temporary Lock

Figure 2-404 MPUR17_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-406 MPUR17_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.84 MPUR17_COMMIT Register (Offset = 20Ch) [Reset = 00000000h]

MPUR17_COMMIT is shown in Figure 2-405 and described in Table 2-407.

Return to the Summary Table.

MPU 17 Permanent Commit

Figure 2-405 MPUR17_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-407 MPUR17_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.85 MPUR17_ACCESS Register (Offset = 210h) [Reset = 00000000h]

MPUR17_ACCESS is shown in Figure 2-406 and described in Table 2-408.

Return to the Summary Table.

MPU Region 17 R/W Access Permissions

Figure 2-406 MPUR17_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-408 MPUR17_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.86 MPUR18_START Register (Offset = 220h) [Reset = 00000000h]

MPUR18_START is shown in Figure 2-407 and described in Table 2-409.

Return to the Summary Table.

MPU Region 18 Start Address

Figure 2-407 MPUR18_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-409 MPUR18_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.87 MPUR18_END Register (Offset = 224h) [Reset = 00000000h]

MPUR18_END is shown in Figure 2-408 and described in Table 2-410.

Return to the Summary Table.

MPU Region 18 End Address

Figure 2-408 MPUR18_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-410 MPUR18_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.88 MPUR18_LOCK Register (Offset = 228h) [Reset = 00000000h]

MPUR18_LOCK is shown in Figure 2-409 and described in Table 2-411.

Return to the Summary Table.

MPU 18 Temporary Lock

Figure 2-409 MPUR18_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-411 MPUR18_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.89 MPUR18_COMMIT Register (Offset = 22Ch) [Reset = 00000000h]

MPUR18_COMMIT is shown in Figure 2-410 and described in Table 2-412.

Return to the Summary Table.

MPU 18 Permanent Commit

Figure 2-410 MPUR18_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-412 MPUR18_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.90 MPUR18_ACCESS Register (Offset = 230h) [Reset = 00000000h]

MPUR18_ACCESS is shown in Figure 2-411 and described in Table 2-413.

Return to the Summary Table.

MPU Region 18 R/W Access Permissions

Figure 2-411 MPUR18_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-413 MPUR18_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.91 MPUR19_START Register (Offset = 240h) [Reset = 00000000h]

MPUR19_START is shown in Figure 2-412 and described in Table 2-414.

Return to the Summary Table.

MPU Region 19 Start Address

Figure 2-412 MPUR19_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-414 MPUR19_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.92 MPUR19_END Register (Offset = 244h) [Reset = 00000000h]

MPUR19_END is shown in Figure 2-413 and described in Table 2-415.

Return to the Summary Table.

MPU Region 19 End Address

Figure 2-413 MPUR19_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-415 MPUR19_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.93 MPUR19_LOCK Register (Offset = 248h) [Reset = 00000000h]

MPUR19_LOCK is shown in Figure 2-414 and described in Table 2-416.

Return to the Summary Table.

MPU 19 Temporary Lock

Figure 2-414 MPUR19_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-416 MPUR19_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.94 MPUR19_COMMIT Register (Offset = 24Ch) [Reset = 00000000h]

MPUR19_COMMIT is shown in Figure 2-415 and described in Table 2-417.

Return to the Summary Table.

MPU 19 Permanent Commit

Figure 2-415 MPUR19_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-417 MPUR19_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.95 MPUR19_ACCESS Register (Offset = 250h) [Reset = 00000000h]

MPUR19_ACCESS is shown in Figure 2-416 and described in Table 2-418.

Return to the Summary Table.

MPU Region 19 R/W Access Permissions

Figure 2-416 MPUR19_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-418 MPUR19_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.96 MPUR20_START Register (Offset = 260h) [Reset = 00000000h]

MPUR20_START is shown in Figure 2-417 and described in Table 2-419.

Return to the Summary Table.

MPU Region 20 Start Address

Figure 2-417 MPUR20_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-419 MPUR20_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.97 MPUR20_END Register (Offset = 264h) [Reset = 00000000h]

MPUR20_END is shown in Figure 2-418 and described in Table 2-420.

Return to the Summary Table.

MPU Region 20 End Address

Figure 2-418 MPUR20_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-420 MPUR20_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.98 MPUR20_LOCK Register (Offset = 268h) [Reset = 00000000h]

MPUR20_LOCK is shown in Figure 2-419 and described in Table 2-421.

Return to the Summary Table.

MPU 20 Temporary Lock

Figure 2-419 MPUR20_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-421 MPUR20_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.99 MPUR20_COMMIT Register (Offset = 26Ch) [Reset = 00000000h]

MPUR20_COMMIT is shown in Figure 2-420 and described in Table 2-422.

Return to the Summary Table.

MPU 20 Permanent Commit

Figure 2-420 MPUR20_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-422 MPUR20_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.100 MPUR20_ACCESS Register (Offset = 270h) [Reset = 00000000h]

MPUR20_ACCESS is shown in Figure 2-421 and described in Table 2-423.

Return to the Summary Table.

MPU Region 20 R/W Access Permissions

Figure 2-421 MPUR20_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-423 MPUR20_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.101 MPUR21_START Register (Offset = 280h) [Reset = 00000000h]

MPUR21_START is shown in Figure 2-422 and described in Table 2-424.

Return to the Summary Table.

MPU Region 21 Start Address

Figure 2-422 MPUR21_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-424 MPUR21_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.102 MPUR21_END Register (Offset = 284h) [Reset = 00000000h]

MPUR21_END is shown in Figure 2-423 and described in Table 2-425.

Return to the Summary Table.

MPU Region 21 End Address

Figure 2-423 MPUR21_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-425 MPUR21_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.103 MPUR21_LOCK Register (Offset = 288h) [Reset = 00000000h]

MPUR21_LOCK is shown in Figure 2-424 and described in Table 2-426.

Return to the Summary Table.

MPU 21 Temporary Lock

Figure 2-424 MPUR21_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-426 MPUR21_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.104 MPUR21_COMMIT Register (Offset = 28Ch) [Reset = 00000000h]

MPUR21_COMMIT is shown in Figure 2-425 and described in Table 2-427.

Return to the Summary Table.

MPU 21 Permanent Commit

Figure 2-425 MPUR21_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-427 MPUR21_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.105 MPUR21_ACCESS Register (Offset = 290h) [Reset = 00000000h]

MPUR21_ACCESS is shown in Figure 2-426 and described in Table 2-428.

Return to the Summary Table.

MPU Region 21 R/W Access Permissions

Figure 2-426 MPUR21_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-428 MPUR21_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.106 MPUR22_START Register (Offset = 2A0h) [Reset = 00000000h]

MPUR22_START is shown in Figure 2-427 and described in Table 2-429.

Return to the Summary Table.

MPU Region 22 Start Address

Figure 2-427 MPUR22_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-429 MPUR22_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.107 MPUR22_END Register (Offset = 2A4h) [Reset = 00000000h]

MPUR22_END is shown in Figure 2-428 and described in Table 2-430.

Return to the Summary Table.

MPU Region 22 End Address

Figure 2-428 MPUR22_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-430 MPUR22_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.108 MPUR22_LOCK Register (Offset = 2A8h) [Reset = 00000000h]

MPUR22_LOCK is shown in Figure 2-429 and described in Table 2-431.

Return to the Summary Table.

MPU 22 Temporary Lock

Figure 2-429 MPUR22_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-431 MPUR22_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.109 MPUR22_COMMIT Register (Offset = 2ACh) [Reset = 00000000h]

MPUR22_COMMIT is shown in Figure 2-430 and described in Table 2-432.

Return to the Summary Table.

MPU 22 Permanent Commit

Figure 2-430 MPUR22_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-432 MPUR22_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.110 MPUR22_ACCESS Register (Offset = 2B0h) [Reset = 00000000h]

MPUR22_ACCESS is shown in Figure 2-431 and described in Table 2-433.

Return to the Summary Table.

MPU Region 22 R/W Access Permissions

Figure 2-431 MPUR22_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-433 MPUR22_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.111 MPUR23_START Register (Offset = 2C0h) [Reset = 00000000h]

MPUR23_START is shown in Figure 2-432 and described in Table 2-434.

Return to the Summary Table.

MPU Region 23 Start Address

Figure 2-432 MPUR23_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-434 MPUR23_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.112 MPUR23_END Register (Offset = 2C4h) [Reset = 00000000h]

MPUR23_END is shown in Figure 2-433 and described in Table 2-435.

Return to the Summary Table.

MPU Region 23 End Address

Figure 2-433 MPUR23_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-435 MPUR23_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.113 MPUR23_LOCK Register (Offset = 2C8h) [Reset = 00000000h]

MPUR23_LOCK is shown in Figure 2-434 and described in Table 2-436.

Return to the Summary Table.

MPU 23 Temporary Lock

Figure 2-434 MPUR23_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-436 MPUR23_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.114 MPUR23_COMMIT Register (Offset = 2CCh) [Reset = 00000000h]

MPUR23_COMMIT is shown in Figure 2-435 and described in Table 2-437.

Return to the Summary Table.

MPU 23 Permanent Commit

Figure 2-435 MPUR23_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-437 MPUR23_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.115 MPUR23_ACCESS Register (Offset = 2D0h) [Reset = 00000000h]

MPUR23_ACCESS is shown in Figure 2-436 and described in Table 2-438.

Return to the Summary Table.

MPU Region 23 R/W Access Permissions

Figure 2-436 MPUR23_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-438 MPUR23_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.116 MPUR24_START Register (Offset = 2E0h) [Reset = 00000000h]

MPUR24_START is shown in Figure 2-437 and described in Table 2-439.

Return to the Summary Table.

MPU Region 24 Start Address

Figure 2-437 MPUR24_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-439 MPUR24_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.117 MPUR24_END Register (Offset = 2E4h) [Reset = 00000000h]

MPUR24_END is shown in Figure 2-438 and described in Table 2-440.

Return to the Summary Table.

MPU Region 24 End Address

Figure 2-438 MPUR24_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-440 MPUR24_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.118 MPUR24_LOCK Register (Offset = 2E8h) [Reset = 00000000h]

MPUR24_LOCK is shown in Figure 2-439 and described in Table 2-441.

Return to the Summary Table.

MPU 24 Temporary Lock

Figure 2-439 MPUR24_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-441 MPUR24_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.119 MPUR24_COMMIT Register (Offset = 2ECh) [Reset = 00000000h]

MPUR24_COMMIT is shown in Figure 2-440 and described in Table 2-442.

Return to the Summary Table.

MPU 24 Permanent Commit

Figure 2-440 MPUR24_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-442 MPUR24_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.120 MPUR24_ACCESS Register (Offset = 2F0h) [Reset = 00000000h]

MPUR24_ACCESS is shown in Figure 2-441 and described in Table 2-443.

Return to the Summary Table.

MPU Region 24 R/W Access Permissions

Figure 2-441 MPUR24_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-443 MPUR24_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.121 MPUR25_START Register (Offset = 300h) [Reset = 00000000h]

MPUR25_START is shown in Figure 2-442 and described in Table 2-444.

Return to the Summary Table.

MPU Region 25 Start Address

Figure 2-442 MPUR25_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-444 MPUR25_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.122 MPUR25_END Register (Offset = 304h) [Reset = 00000000h]

MPUR25_END is shown in Figure 2-443 and described in Table 2-445.

Return to the Summary Table.

MPU Region 25 End Address

Figure 2-443 MPUR25_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-445 MPUR25_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.123 MPUR25_LOCK Register (Offset = 308h) [Reset = 00000000h]

MPUR25_LOCK is shown in Figure 2-444 and described in Table 2-446.

Return to the Summary Table.

MPU 25 Temporary Lock

Figure 2-444 MPUR25_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-446 MPUR25_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.124 MPUR25_COMMIT Register (Offset = 30Ch) [Reset = 00000000h]

MPUR25_COMMIT is shown in Figure 2-445 and described in Table 2-447.

Return to the Summary Table.

MPU 25 Permanent Commit

Figure 2-445 MPUR25_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-447 MPUR25_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.125 MPUR25_ACCESS Register (Offset = 310h) [Reset = 00000000h]

MPUR25_ACCESS is shown in Figure 2-446 and described in Table 2-448.

Return to the Summary Table.

MPU Region 25 R/W Access Permissions

Figure 2-446 MPUR25_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-448 MPUR25_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.126 MPUR26_START Register (Offset = 320h) [Reset = 00000000h]

MPUR26_START is shown in Figure 2-447 and described in Table 2-449.

Return to the Summary Table.

MPU Region 26 Start Address

Figure 2-447 MPUR26_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-449 MPUR26_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.127 MPUR26_END Register (Offset = 324h) [Reset = 00000000h]

MPUR26_END is shown in Figure 2-448 and described in Table 2-450.

Return to the Summary Table.

MPU Region 26 End Address

Figure 2-448 MPUR26_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-450 MPUR26_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.128 MPUR26_LOCK Register (Offset = 328h) [Reset = 00000000h]

MPUR26_LOCK is shown in Figure 2-449 and described in Table 2-451.

Return to the Summary Table.

MPU 26 Temporary Lock

Figure 2-449 MPUR26_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-451 MPUR26_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.129 MPUR26_COMMIT Register (Offset = 32Ch) [Reset = 00000000h]

MPUR26_COMMIT is shown in Figure 2-450 and described in Table 2-452.

Return to the Summary Table.

MPU 26 Permanent Commit

Figure 2-450 MPUR26_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-452 MPUR26_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.130 MPUR26_ACCESS Register (Offset = 330h) [Reset = 00000000h]

MPUR26_ACCESS is shown in Figure 2-451 and described in Table 2-453.

Return to the Summary Table.

MPU Region 26 R/W Access Permissions

Figure 2-451 MPUR26_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-453 MPUR26_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.131 MPUR27_START Register (Offset = 340h) [Reset = 00000000h]

MPUR27_START is shown in Figure 2-452 and described in Table 2-454.

Return to the Summary Table.

MPU Region 27 Start Address

Figure 2-452 MPUR27_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-454 MPUR27_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.132 MPUR27_END Register (Offset = 344h) [Reset = 00000000h]

MPUR27_END is shown in Figure 2-453 and described in Table 2-455.

Return to the Summary Table.

MPU Region 27 End Address

Figure 2-453 MPUR27_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-455 MPUR27_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.133 MPUR27_LOCK Register (Offset = 348h) [Reset = 00000000h]

MPUR27_LOCK is shown in Figure 2-454 and described in Table 2-456.

Return to the Summary Table.

MPU 27 Temporary Lock

Figure 2-454 MPUR27_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-456 MPUR27_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.134 MPUR27_COMMIT Register (Offset = 34Ch) [Reset = 00000000h]

MPUR27_COMMIT is shown in Figure 2-455 and described in Table 2-457.

Return to the Summary Table.

MPU 27 Permanent Commit

Figure 2-455 MPUR27_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-457 MPUR27_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.135 MPUR27_ACCESS Register (Offset = 350h) [Reset = 00000000h]

MPUR27_ACCESS is shown in Figure 2-456 and described in Table 2-458.

Return to the Summary Table.

MPU Region 27 R/W Access Permissions

Figure 2-456 MPUR27_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-458 MPUR27_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.136 MPUR28_START Register (Offset = 360h) [Reset = 00000000h]

MPUR28_START is shown in Figure 2-457 and described in Table 2-459.

Return to the Summary Table.

MPU Region 28 Start Address

Figure 2-457 MPUR28_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-459 MPUR28_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.137 MPUR28_END Register (Offset = 364h) [Reset = 00000000h]

MPUR28_END is shown in Figure 2-458 and described in Table 2-460.

Return to the Summary Table.

MPU Region 28 End Address

Figure 2-458 MPUR28_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-460 MPUR28_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.138 MPUR28_LOCK Register (Offset = 368h) [Reset = 00000000h]

MPUR28_LOCK is shown in Figure 2-459 and described in Table 2-461.

Return to the Summary Table.

MPU 28 Temporary Lock

Figure 2-459 MPUR28_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-461 MPUR28_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.139 MPUR28_COMMIT Register (Offset = 36Ch) [Reset = 00000000h]

MPUR28_COMMIT is shown in Figure 2-460 and described in Table 2-462.

Return to the Summary Table.

MPU 28 Permanent Commit

Figure 2-460 MPUR28_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-462 MPUR28_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.140 MPUR28_ACCESS Register (Offset = 370h) [Reset = 00000000h]

MPUR28_ACCESS is shown in Figure 2-461 and described in Table 2-463.

Return to the Summary Table.

MPU Region 28 R/W Access Permissions

Figure 2-461 MPUR28_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-463 MPUR28_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.141 MPUR29_START Register (Offset = 380h) [Reset = 00000000h]

MPUR29_START is shown in Figure 2-462 and described in Table 2-464.

Return to the Summary Table.

MPU Region 29 Start Address

Figure 2-462 MPUR29_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-464 MPUR29_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.142 MPUR29_END Register (Offset = 384h) [Reset = 00000000h]

MPUR29_END is shown in Figure 2-463 and described in Table 2-465.

Return to the Summary Table.

MPU Region 29 End Address

Figure 2-463 MPUR29_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-465 MPUR29_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.143 MPUR29_LOCK Register (Offset = 388h) [Reset = 00000000h]

MPUR29_LOCK is shown in Figure 2-464 and described in Table 2-466.

Return to the Summary Table.

MPU 29 Temporary Lock

Figure 2-464 MPUR29_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-466 MPUR29_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.144 MPUR29_COMMIT Register (Offset = 38Ch) [Reset = 00000000h]

MPUR29_COMMIT is shown in Figure 2-465 and described in Table 2-467.

Return to the Summary Table.

MPU 29 Permanent Commit

Figure 2-465 MPUR29_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-467 MPUR29_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.145 MPUR29_ACCESS Register (Offset = 390h) [Reset = 00000000h]

MPUR29_ACCESS is shown in Figure 2-466 and described in Table 2-468.

Return to the Summary Table.

MPU Region 29 R/W Access Permissions

Figure 2-466 MPUR29_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-468 MPUR29_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.146 MPUR30_START Register (Offset = 3A0h) [Reset = 00000000h]

MPUR30_START is shown in Figure 2-467 and described in Table 2-469.

Return to the Summary Table.

MPU Region 30 Start Address

Figure 2-467 MPUR30_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-469 MPUR30_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.147 MPUR30_END Register (Offset = 3A4h) [Reset = 00000000h]

MPUR30_END is shown in Figure 2-468 and described in Table 2-470.

Return to the Summary Table.

MPU Region 30 End Address

Figure 2-468 MPUR30_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-470 MPUR30_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.148 MPUR30_LOCK Register (Offset = 3A8h) [Reset = 00000000h]

MPUR30_LOCK is shown in Figure 2-469 and described in Table 2-471.

Return to the Summary Table.

MPU 30 Temporary Lock

Figure 2-469 MPUR30_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-471 MPUR30_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.149 MPUR30_COMMIT Register (Offset = 3ACh) [Reset = 00000000h]

MPUR30_COMMIT is shown in Figure 2-470 and described in Table 2-472.

Return to the Summary Table.

MPU 30 Permanent Commit

Figure 2-470 MPUR30_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-472 MPUR30_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.150 MPUR30_ACCESS Register (Offset = 3B0h) [Reset = 00000000h]

MPUR30_ACCESS is shown in Figure 2-471 and described in Table 2-473.

Return to the Summary Table.

MPU Region 30 R/W Access Permissions

Figure 2-471 MPUR30_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-473 MPUR30_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.151 MPUR31_START Register (Offset = 3C0h) [Reset = 00000000h]

MPUR31_START is shown in Figure 2-472 and described in Table 2-474.

Return to the Summary Table.

MPU Region 31 Start Address

Figure 2-472 MPUR31_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-474 MPUR31_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.152 MPUR31_END Register (Offset = 3C4h) [Reset = 00000000h]

MPUR31_END is shown in Figure 2-473 and described in Table 2-475.

Return to the Summary Table.

MPU Region 31 End Address

Figure 2-473 MPUR31_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-475 MPUR31_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.153 MPUR31_LOCK Register (Offset = 3C8h) [Reset = 00000000h]

MPUR31_LOCK is shown in Figure 2-474 and described in Table 2-476.

Return to the Summary Table.

MPU 31 Temporary Lock

Figure 2-474 MPUR31_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-476 MPUR31_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.154 MPUR31_COMMIT Register (Offset = 3CCh) [Reset = 00000000h]

MPUR31_COMMIT is shown in Figure 2-475 and described in Table 2-477.

Return to the Summary Table.

MPU 31 Permanent Commit

Figure 2-475 MPUR31_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-477 MPUR31_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.155 MPUR31_ACCESS Register (Offset = 3D0h) [Reset = 00000000h]

MPUR31_ACCESS is shown in Figure 2-476 and described in Table 2-478.

Return to the Summary Table.

MPU Region 31 R/W Access Permissions

Figure 2-476 MPUR31_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-478 MPUR31_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.156 MPUR32_START Register (Offset = 3E0h) [Reset = 00000000h]

MPUR32_START is shown in Figure 2-477 and described in Table 2-479.

Return to the Summary Table.

MPU Region 32 Start Address

Figure 2-477 MPUR32_START Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-479 MPUR32_START Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the start address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.157 MPUR32_END Register (Offset = 3E4h) [Reset = 00000000h]

MPUR32_END is shown in Figure 2-478 and described in Table 2-480.

Return to the Summary Table.

MPU Region 32 End Address

Figure 2-478 MPUR32_END Register
31302928272625242322212019181716
ADDRH
R/W-0h
1514131211109876543210
ADDRLRESERVED
R/W-0hR-0h
Table 2-480 MPUR32_END Register Field Descriptions
BitFieldTypeResetDescription
31-16ADDRHR/W0hUpper 16-bit of the end address, Module will have access to peripherals, SRAMs, FLASH and external memories.

Reset type: SYSRSn

15-12ADDRLR/W0hAddress range start address (granularity of 4KB) within the memory type specified. The values available depends on the memory type chosen and the memory footprint of the device.

Reset type: SYSRSn

11-0RESERVEDR0hReserved

3.14.7.158 MPUR32_LOCK Register (Offset = 3E8h) [Reset = 00000000h]

MPUR32_LOCK is shown in Figure 2-479 and described in Table 2-481.

Return to the Summary Table.

MPU 32 Temporary Lock

Figure 2-479 MPUR32_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-481 MPUR32_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this MPU registers (writes will have no effect on them). This bit can only be modified if MPU_COMMIT.COMMIT is cleared. simultaneously.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.159 MPUR32_COMMIT Register (Offset = 3ECh) [Reset = 00000000h]

MPUR32_COMMIT is shown in Figure 2-480 and described in Table 2-482.

Return to the Summary Table.

MPU 32 Permanent Commit

Figure 2-480 MPUR32_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-482 MPUR32_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPU_LOCK register. This bit cannot be cleared, except by reset.
0 : MPU_LOCK is modifiable
1 : MPU_LOCK is committed permanently

Reset type: SYSRSn

3.14.7.160 MPUR32_ACCESS Register (Offset = 3F0h) [Reset = 00000000h]

MPUR32_ACCESS is shown in Figure 2-481 and described in Table 2-483.

Return to the Summary Table.

MPU Region 32 R/W Access Permissions

Figure 2-481 MPUR32_ACCESS Register
31302928272625242322212019181716
RESERVED
R-0h
1514131211109876543210
RESERVEDACCESS
R-0hR/W-0h
Table 2-483 MPUR32_ACCESS Register Field Descriptions
BitFieldTypeResetDescription
31-2RESERVEDR0hReserved
1-0ACCESSR/W0hEnables the type of accesses allowed in this region.
00 : No access
01 : Read Access
10 : Read/Write Access
11 : Read/Write Access

Reset type: SYSRSn

3.14.7.161 MPUCTRL Register (Offset = 800h) [Reset = 00000000h]

MPUCTRL is shown in Figure 2-482 and described in Table 2-484.

Return to the Summary Table.

MPU Control Register

Figure 2-482 MPUCTRL Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDMPUEN
R-0hR/W-0h
Table 2-484 MPUCTRL Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0MPUENR/W0hThis register can only be modified by SROOT (LINK2).
0 : MPU function disabled
1 : MPU function Enabled

Reset type: SYSRSn

3.14.7.162 MPUCFG_LOCK Register (Offset = 820h) [Reset = 00000000h]

MPUCFG_LOCK is shown in Figure 2-483 and described in Table 2-485.

Return to the Summary Table.

Channel Configuration Temporary Lock

Figure 2-483 MPUCFG_LOCK Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDLOCK
R-0hR/W-0h
Table 2-485 MPUCFG_LOCK Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0LOCKR/W0hWhen set, locks this corresponding MPU configuration register MPUCTRL (writes will have no effect on them). This bit can only be modified if MPUCFG_COMMIT.COMMIT is cleared.
0 : Unlocked
1 : Locked

Reset type: SYSRSn

3.14.7.163 MPUCFG_COMMIT Register (Offset = 824h) [Reset = 00000000h]

MPUCFG_COMMIT is shown in Figure 2-484 and described in Table 2-486.

Return to the Summary Table.

Channel Configuration Permanent Commit

Figure 2-484 MPUCFG_COMMIT Register
3130292827262524
RESERVED
R-0h
2322212019181716
RESERVED
R-0h
15141312111098
RESERVED
R-0h
76543210
RESERVEDCOMMIT
R-0hR/W1S-0h
Table 2-486 MPUCFG_COMMIT Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0COMMITR/W1S0hWhen set, locks the MPUCFG_LOCK register. This bit cannot be cleared, except by reset.
0 : MPUCFG_LOCK is modifiable
1 : MPUCFG_LOCK is committed permanently

Reset type: SYSRSn