ZHCU948B September 2020 – May 2022 BQ76952
类别 | 子类别 | 名称 | 类型 | 最小值 | 最大值 | 默认值 | 单位 |
---|---|---|---|---|---|---|---|
Settings | Configuration | Vcell Mode | H2 | 0x0000 | 0xFFFF | 0x0000 | 十六进制 |
15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
Cell 16 Mode | Cell 15 Mode | Cell 14 Mode | Cell 13 Mode | Cell 12 Mode | Cell 11 Mode | Cell 10 Mode | Cell 9 Mode |
7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
Cell 8 Mode | Cell 7 Mode | Cell 6 Mode | Cell 5 Mode | Cell 4 Mode | Cell 3 Mode | Cell 2 Mode | Cell 1 Mode |
说明:并非每个系统都会使用所有电芯输入引脚。如果系统的电芯数少于器件支持的数量,一些 VC 输入引脚可能会短接在一起或用于测量电芯之间的互连电阻。为防止在短接或用于测量互连电阻的引脚上针对电芯欠压采取措施,应清除相应的 Vcell Mode 位。如果所有 Vcell Mode 位都被清除,则所有输入都被视为电芯连接。
位 | 字段 | 默认值 | 说明 |
---|---|---|---|
15 | Cell 16 Mode | 0 | 0 = VC16 和 VC15 之间电芯未连接。禁用电芯 16 上的保护。 1 = VC16 和 VC15 之间电芯已连接。启用电芯 16 上的保护。 |
14 | Cell 15 Mode | 0 | 0 = VC15 和 VC14 之间电芯未连接。禁用电芯 15 上的保护。 1 = VC15 和 VC14 之间电芯已连接。启用电芯 15 上的保护。 |
13 | Cell 14 Mode | 0 | 0 = VC14 和 VC13 之间电芯未连接。禁用电芯 14 上的保护。 1 = VC14 和 VC13 之间电芯已连接。启用电芯 14 上的保护。 |
12 | Cell 13 Mode | 0 | 0 = VC13 和 VC12 之间电芯未连接。禁用电芯 13 上的保护。 1 = VC13 和 VC12 之间电芯已连接。启用电芯 13 上的保护。 |
11 | Cell 12 Mode | 0 | 0 = VC12 和 VC11 之间电芯未连接。禁用电芯 12 上的保护。 1 = VC12 和 VC11 之间电芯已连接。启用电芯 12 上的保护。 |
10 | Cell 11 Mode | 0 | 0 = VC11 和 VC10 之间电芯未连接。禁用电芯 11 上的保护。 1 = VC11 和 VC10 之间电芯已连接。启用电芯 11 上的保护。 |
9 | Cell 10 Mode | 0 | 0 = VC10 和 VC9 之间电芯未连接。禁用电芯 10 上的保护。 1 = VC10 和 VC9 之间电芯已连接。启用电芯 10 上的保护。 |
8 | Cell 9 Mode | 0 | 0 = VC9 和 VC8 之间电芯未连接。禁用电芯 9 上的保护。 1 = VC9 和 VC8 之间电芯已连接。启用电芯 9 上的保护。 |
7 | Cell 8 Mode | 0 | 0 = VC8 和 VC7 之间电芯未连接。禁用电芯 8 上的保护。 1 = VC8 和 VC7 之间电芯已连接。启用电芯 8 上的保护。 |
6 | Cell 7 Mode | 0 | 0 = VC7 和 VC6 之间电芯未连接。禁用电芯 7 上的保护。 1 = VC7 和 VC6 之间电芯已连接。启用电芯 7 上的保护。 |
5 | Cell 6 Mode | 0 | 0 = VC6 和 VC5 之间电芯未连接。禁用电芯 6 上的保护。 1 = VC6 和 VC5 之间电芯已连接。启用电芯 6 上的保护。 |
4 | Cell 5 Mode | 0 | 0 = VC5 和 VC4 之间电芯未连接。禁用电芯 5 上的保护。 1 = VC5 和 VC4 之间电芯已连接。启用电芯 5 上的保护。 |
3 | Cell 4 Mode | 0 | 0 = VC4 和 VC3 之间电芯未连接。禁用电芯 4 上的保护。 1 = VC4 和 VC3 之间电芯已连接。启用电芯 4 上的保护。 |
2 | Cell 3 Mode | 0 | 0 = VC3 和 VC2 之间电芯未连接。禁用电芯 3 上的保护。 1 = VC3 和 VC2 之间电芯已连接。启用电芯 3 上的保护。 |
1 | Cell 2 Mode | 0 | 0 = VC2 和 VC1 之间电芯未连接。禁用电芯 2 上的保护。 1 = VC2 和 VC1 之间电芯已连接。启用电芯 2 上的保护。 |
0 | Cell 1 Mode | 0 | 0 = VC1 和 VC0 之间电芯未连接。禁用 电芯 1 上的保护。 1 = VC1 和 VC0 之间电芯已连接。启用电芯 1 上的保护。 |