SWCU191 February   2022 CC1311P3 , CC1311R3 , CC2651P3 , CC2651R3 , CC2651R3SIPA

 

  1. 1 Read This First
    1.     About This Manual
    2.     Devices
    3.     Register, Field, and Bit Calls
    4.     Related Documentation
    5. 1.1 Trademarks
  2. 2 Architectural Overview
    1. 2.1 Target Applications
    2. 2.2 Overview
    3. 2.3 Functional Overview
      1. 2.3.1  Arm® Cortex®-M4
        1. 2.3.1.1 Processor Core
        2. 2.3.1.2 System Timer (SysTick)
        3. 2.3.1.3 Nested Vector Interrupt Controller (NVIC)
        4. 2.3.1.4 System Control Block
      2. 2.3.2  On-Chip Memory
        1. 2.3.2.1 SRAM
        2. 2.3.2.2 Flash Memory
        3. 2.3.2.3 ROM
      3. 2.3.3  Radio
      4. 2.3.4  Security Core
      5. 2.3.5  General-Purpose Timers
        1. 2.3.5.1 Watchdog Timer
        2. 2.3.5.2 Always-On Domain
      6. 2.3.6  Direct Memory Access
      7. 2.3.7  System Control and Clock
      8. 2.3.8  Serial Communication Peripherals
        1. 2.3.8.1 UART
        2. 2.3.8.2 I2C
        3. 2.3.8.3 I2S
        4. 2.3.8.4 SSI
      9. 2.3.9  Programmable I/Os
      10. 2.3.10 Analog Peripherals
      11. 2.3.11 Random Number Generator
      12. 2.3.12 cJTAG and JTAG
      13. 2.3.13 Power Supply System
        1. 2.3.13.1 Supply System
          1. 2.3.13.1.1 VDDS
          2. 2.3.13.1.2 VDDR
          3. 2.3.13.1.3 Digital Core Supply
          4. 2.3.13.1.4 Other Internal Supplies
        2. 2.3.13.2 DC/DC Converter
  3. 3 Arm® Cortex®-M4 Processor
    1. 3.1 Arm® Cortex®-M4 Processor Introduction
    2. 3.2 Block Diagram
    3. 3.3 Overview
      1. 3.3.1 System-Level Interface
      2. 3.3.2 Integrated Configurable Debug
      3. 3.3.3 Trace Port Interface Unit
      4. 3.3.4 Arm® Cortex®-M4 System Component Details
    4. 3.4 Programming Model
      1. 3.4.1 Processor Mode and Privilege Levels for Software Execution
      2. 3.4.2 Stacks
      3. 3.4.3 Exceptions and Interrupts
      4. 3.4.4 Data Types
    5. 3.5 Arm® Cortex®-M4 Core Registers
      1. 3.5.1 Core Register Map
      2. 3.5.2 Core Register Descriptions
        1. 3.5.2.1  Cortex®General-Purpose Register 0 (R0)
        2. 3.5.2.2  Cortex® General-Purpose Register 1 (R1)
        3. 3.5.2.3  Cortex® General-Purpose Register 2 (R2)
        4. 3.5.2.4  Cortex® General-Purpose Register 3 (R3)
        5. 3.5.2.5  Cortex® General-Purpose Register 4 (R4)
        6. 3.5.2.6  Cortex® General-Purpose Register 5 (R5)
        7. 3.5.2.7  Cortex® General-Purpose Register 6 (R6)
        8. 3.5.2.8  Cortex® General-Purpose Register 7 (R7)
        9. 3.5.2.9  Cortex® General-Purpose Register 8 (R8)
        10. 3.5.2.10 Cortex® General-Purpose Register 9 (R9)
        11. 3.5.2.11 Cortex® General-Purpose Register 10 (R10)
        12. 3.5.2.12 Cortex® General-Purpose Register 11 (R11)
        13. 3.5.2.13 Cortex® General-Purpose Register 12 (R12)
        14. 3.5.2.14 Stack Pointer (SP)
        15. 3.5.2.15 Link Register (LR)
        16. 3.5.2.16 Program Counter (PC)
        17. 3.5.2.17 Program Status Register (PSR)
        18. 3.5.2.18 Priority Mask Register (PRIMASK)
        19. 3.5.2.19 Fault Mask Register (FAULTMASK)
        20. 3.5.2.20 Base Priority Mask Register (BASEPRI)
        21. 3.5.2.21 Control Register (CONTROL)
    6. 3.6 Instruction Set Summary
      1. 3.6.1 Arm® Cortex®-M4 Instructions
      2. 3.6.2 Load and Store Timings
      3. 3.6.3 Binary Compatibility With Other Cortex® Processors
    7. 3.7 Arm® Cortex®-M4 Processor Registers
      1. 3.7.1 CPU_DWT Registers
      2. 3.7.2 CPU_FPB Registers
      3. 3.7.3 CPU_ITM Registers
      4. 3.7.4 CPU_SCS Registers
      5. 3.7.5 CPU_TPIU Registers
  4. 4 Memory Map
    1. 4.1 Memory Map
  5. 5 Arm® Cortex®-M4 Peripherals
    1. 5.1 Arm® Cortex®-M4 Peripherals Introduction
    2. 5.2 Functional Description
      1. 5.2.1 SysTick
      2. 5.2.2 NVIC
        1. 5.2.2.1 Level-Sensitive and Pulse Interrupts
        2. 5.2.2.2 Hardware and Software Control of Interrupts
      3. 5.2.3 SCB
      4. 5.2.4 ITM
      5. 5.2.5 FPB
      6. 5.2.6 TPIU
      7. 5.2.7 DWT
  6. 6 Interrupts and Events
    1. 6.1 Exception Model
      1. 6.1.1 Exception States
      2. 6.1.2 Exception Types
      3. 6.1.3 Exception Handlers
      4. 6.1.4 Vector Table
      5. 6.1.5 Exception Priorities
      6. 6.1.6 Interrupt Priority Grouping
      7. 6.1.7 Exception Entry and Return
        1. 6.1.7.1 Exception Entry
        2. 6.1.7.2 Exception Return
    2. 6.2 Fault Handling
      1. 6.2.1 Fault Types
      2. 6.2.2 Fault Escalation and Hard Faults
      3. 6.2.3 Fault Status Registers and Fault Address Registers
      4. 6.2.4 Lockup
    3. 6.3 Event Fabric
      1. 6.3.1 Introduction
      2. 6.3.2 Event Fabric Overview
        1. 6.3.2.1 Registers
    4. 6.4 AON Event Fabric
      1. 6.4.1 Common Input Event List
      2. 6.4.2 Event Subscribers
        1. 6.4.2.1 Wake-Up Controller (WUC)
        2. 6.4.2.2 Real-Time Clock
        3. 6.4.2.3 MCU Event Fabric
    5. 6.5 MCU Event Fabric
      1. 6.5.1 Common Input Event List
      2. 6.5.2 Event Subscribers
        1. 6.5.2.1 System CPU
        2. 6.5.2.2 NMI
        3. 6.5.2.3 Freeze
    6. 6.6 AON Events
    7. 6.7 Interrupts and Events Registers
      1. 6.7.1 AON_EVENT Registers
      2. 6.7.2 EVENT Registers
  7. 7 JTAG Interface
    1. 7.1  Top-Level Debug System
    2. 7.2  cJTAG
      1. 7.2.1 cJTAG Commands
        1. 7.2.1.1 Mandatory Commands
      2. 7.2.2 Programming Sequences
        1. 7.2.2.1 Opening Command Window
        2. 7.2.2.2 Changing to 4-Pin Mode
        3. 7.2.2.3 Close Command Window
    3. 7.3  ICEPick
      1. 7.3.1 Secondary TAPs
        1. 7.3.1.1 Slave DAP (CPU DAP)
        2. 7.3.1.2 Ordering Slave TAPs and DAPs
      2. 7.3.2 ICEPick Registers
        1. 7.3.2.1 IR Instructions
        2. 7.3.2.2 Data Shift Register
        3. 7.3.2.3 Instruction Register
        4. 7.3.2.4 Bypass Register
        5. 7.3.2.5 Device Identification Register
        6. 7.3.2.6 User Code Register
        7. 7.3.2.7 ICEPick Identification Register
        8. 7.3.2.8 Connect Register
      3. 7.3.3 Router Scan Chain
      4. 7.3.4 TAP Routing Registers
        1. 7.3.4.1 ICEPick Control Block
          1. 7.3.4.1.1 All0s Register
          2. 7.3.4.1.2 ICEPick Control Register
          3. 7.3.4.1.3 Linking Mode Register
        2. 7.3.4.2 Test TAP Linking Block
          1. 7.3.4.2.1 Secondary Test TAP Register
        3. 7.3.4.3 Debug TAP Linking Block
          1. 7.3.4.3.1 Secondary Debug TAP Register
    4. 7.4  ICEMelter
    5. 7.5  Serial Wire Viewer (SWV)
    6. 7.6  Halt In Boot (HIB)
    7. 7.7  Debug and Shutdown
    8. 7.8  Debug Features Supported Through WUC TAP
    9. 7.9  Profiler Register
    10. 7.10 Boundary Scan
  8. 8 Power, Reset and Clock Management (PRCM)
    1. 8.1 Introduction
    2. 8.2 System CPU Mode
    3. 8.3 Supply System
      1. 8.3.1 Internal DC/DC Converter and Global LDO
    4. 8.4 Digital Power Partitioning
      1. 8.4.1 MCU_VD
        1. 8.4.1.1 MCU_VD Power Domains
      2. 8.4.2 AON_VD
        1. 8.4.2.1 AON_VD Power Domains
    5. 8.5 Clock Management
      1. 8.5.1 System Clocks
        1. 8.5.1.1 Controlling the Oscillators
      2. 8.5.2 Clocks in MCU_VD
        1. 8.5.2.1 Clock Gating
        2. 8.5.2.2 Scaler to GPTs
        3. 8.5.2.3 Scaler to WDT
      3. 8.5.3 Clocks in AON_VD
    6. 8.6 Power Modes
      1. 8.6.1 Start-Up State
      2. 8.6.2 Active Mode
      3. 8.6.3 Idle Mode
      4. 8.6.4 Standby Mode
      5. 8.6.5 Shutdown Mode
    7. 8.7 Reset
      1. 8.7.1 System Resets
        1. 8.7.1.1 Clock Loss Detection
        2. 8.7.1.2 Software-Initiated System Reset
        3. 8.7.1.3 Warm Reset Converted to System Reset
      2. 8.7.2 Reset of the MCU_VD Power Domains and Modules
      3. 8.7.3 Reset of AON_VD
    8. 8.8 PRCM Registers
      1. 8.8.1 OSC_DIG Registers
      2. 8.8.2 PRCM Registers
      3. 8.8.3 AON_PMCTL Registers
  9. 9 Versatile Instruction Memory System (VIMS)
    1. 9.1 Introduction
    2. 9.2 VIMS Configurations
      1. 9.2.1 VIMS Modes
        1. 9.2.1.1 GPRAM Mode
        2. 9.2.1.2 Off Mode
        3. 9.2.1.3 Cache Mode
      2. 9.2.2 VIMS FLASH Line Buffers
      3. 9.2.3 VIMS Arbitration
      4. 9.2.4 VIMS Cache TAG Prefetch
    3. 9.3 VIMS Software Remarks
      1. 9.3.1 FLASH Program or Update
      2. 9.3.2 VIMS Retention
        1. 9.3.2.1 Mode 1
        2. 9.3.2.2 Mode 2
        3. 9.3.2.3 Mode 3
    4. 9.4 ROM
    5. 9.5 FLASH
      1. 9.5.1 FLASH Memory Protection
      2. 9.5.2 Memory Programming
      3. 9.5.3 FLASH Memory Programming
      4. 9.5.4 Power Management Requirements
    6. 9.6 ROM Functions
    7. 9.7 VIMS Registers
      1. 9.7.1 FLASH Registers
      2. 9.7.2 VIMS Registers
  10. 10SRAM
    1. 10.1 Introduction
    2. 10.2 Main Features
    3. 10.3 Data Retention
    4. 10.4 Parity and SRAM Error Support
    5. 10.5 SRAM Auto-Initialization
    6. 10.6 Parity Debug Behavior
    7. 10.7 SRAM Registers
      1. 10.7.1 SRAM Registers
  11. 11Bootloader
    1. 11.1 Bootloader Functionality
      1. 11.1.1 Bootloader Disabling
      2. 11.1.2 Bootloader Backdoor
    2. 11.2 Bootloader Interfaces
      1. 11.2.1 Packet Handling
        1. 11.2.1.1 Packet Acknowledge and Not-Acknowledge Bytes
      2. 11.2.2 Transport Layer
        1. 11.2.2.1 UART Transport
          1. 11.2.2.1.1 UART Baud Rate Automatic Detection
        2. 11.2.2.2 SSI Transport
      3. 11.2.3 Serial Bus Commands
        1. 11.2.3.1  COMMAND_PING
        2. 11.2.3.2  COMMAND_DOWNLOAD
        3. 11.2.3.3  COMMAND_SEND_DATA
        4. 11.2.3.4  COMMAND_SECTOR_ERASE
        5. 11.2.3.5  COMMAND_GET_STATUS
        6. 11.2.3.6  COMMAND_RESET
        7. 11.2.3.7  COMMAND_GET_CHIP_ID
        8. 11.2.3.8  COMMAND_CRC32
        9. 11.2.3.9  COMMAND_BANK_ERASE
        10. 11.2.3.10 COMMAND_MEMORY_READ
        11. 11.2.3.11 COMMAND_MEMORY_WRITE
        12. 11.2.3.12 COMMAND_SET_CCFG
        13. 11.2.3.13 COMMAND_DOWNLOAD_CRC
  12. 12Device Configuration
    1. 12.1 Customer Configuration (CCFG)
    2. 12.2 CCFG Registers
      1. 12.2.1 CCFG Registers
    3. 12.3 Factory Configuration (FCFG)
    4. 12.4 FCFG Registers
      1. 12.4.1 FCFG1 Registers
  13. 13Cryptography
    1. 13.1 AES Cryptoprocessor Introduction
    2. 13.2 Functional Description
      1. 13.2.1 Debug Capabilities
      2. 13.2.2 Exception Handling
    3. 13.3 Power Management and Sleep Modes
    4. 13.4 Hardware Description
      1. 13.4.1 AHB Slave Bus
      2. 13.4.2 AHB Master Bus
      3. 13.4.3 Interrupts
    5. 13.5 Module Description
      1. 13.5.1 Introduction
      2. 13.5.2 Module Memory Map
      3. 13.5.3 DMA Controller
        1. 13.5.3.1 Internal Operation
        2. 13.5.3.2 Supported DMA Operations
      4. 13.5.4 Master Control and Select Module
        1. 13.5.4.1 Algorithm Select Register
          1. 13.5.4.1.1 Algorithm Select
        2. 13.5.4.2 Master Transfer Protection
          1. 13.5.4.2.1 Master Transfer Protection Control
        3. 13.5.4.3 Software Reset
      5. 13.5.5 AES Engine
        1. 13.5.5.1 Second Key Registers (Internal, But Clearable)
        2. 13.5.5.2 AES Initialization Vector (IV) Registers
        3. 13.5.5.3 AES I/O Buffer Control, Mode, and Length Registers
        4. 13.5.5.4 Data Input and Output Registers
        5. 13.5.5.5 TAG Registers
      6. 13.5.6 Key Area Registers
        1. 13.5.6.1 Key Write Area Register
        2. 13.5.6.2 Key Written Area Register
        3. 13.5.6.3 Key Size Register
        4. 13.5.6.4 Key Store Read Area Register
    6. 13.6 AES Module Performance
      1. 13.6.1 Introduction
      2. 13.6.2 Performance for DMA-Based Operations
    7. 13.7 Programming Guidelines
      1. 13.7.1 One-Time Initialization After a Reset
      2. 13.7.2 DMAC and Master Control
        1. 13.7.2.1 Regular Use
        2. 13.7.2.2 Interrupting DMA Transfers
        3. 13.7.2.3 Interrupts, Hardware, and Software Synchronization
      3. 13.7.3 Encryption and Decryption
        1. 13.7.3.1 Key Store
          1. 13.7.3.1.1 Load Keys From External Memory
        2. 13.7.3.2 Basic AES Modes
          1. 13.7.3.2.1 AES-ECB
          2. 13.7.3.2.2 AES-CBC
          3. 13.7.3.2.3 AES-CTR
          4. 13.7.3.2.4 Programming Sequence With DMA Data
        3. 13.7.3.3 CBC-MAC
          1. 13.7.3.3.1 Programming Sequence for CBC-MAC
        4. 13.7.3.4 AES-CCM
          1. 13.7.3.4.1 Programming Sequence for AES-CCM
      4. 13.7.4 Exceptions Handling
        1. 13.7.4.1 Soft Reset
        2. 13.7.4.2 External Port Errors
        3. 13.7.4.3 Key Store Errors
    8. 13.8 Conventions and Compliances
      1. 13.8.1 Conventions Used in This Manual
        1. 13.8.1.1 Terminology
        2. 13.8.1.2 Formulas and Nomenclature
      2. 13.8.2 Compliance
    9. 13.9 Cryptography Registers
      1. 13.9.1 CRYPTO Registers
  14. 14I/O Controller (IOC)
    1. 14.1  Introduction
    2. 14.2  IOC Overview
    3. 14.3  I/O Mapping and Configuration
      1. 14.3.1 Basic I/O Mapping
      2. 14.3.2 Mapping AUXIOs to DIO Pins
      3. 14.3.3 Control External LNA/PA (Range Extender) With I/Os
      4. 14.3.4 Map the 32 kHz System Clock (LF Clock) to DIO
    4. 14.4  Edge Detection on DIO Pins
      1. 14.4.1 Configure DIO as GPIO Input to Generate Interrupt on EDGE DETECT
    5. 14.5  Unused I/O Pins
    6. 14.6  GPIO
    7. 14.7  I/O Pin Capability
    8. 14.8  Peripheral PORTIDs
    9. 14.9  I/O Pins
      1. 14.9.1 Input/Output Modes
        1. 14.9.1.1 Physical Pin
        2. 14.9.1.2 Pin Configuration
    10. 14.10 IOC Registers
      1. 14.10.1 AON_IOC Registers
      2. 14.10.2 GPIO Registers
      3. 14.10.3 IOC Registers
  15. 15Micro Direct Memory Access (µDMA)
    1. 15.1 μDMA Introduction
    2. 15.2 Block Diagram
    3. 15.3 Functional Description
      1. 15.3.1  Channel Assignments
      2. 15.3.2  Priority
      3. 15.3.3  Arbitration Size
      4. 15.3.4  Request Types
        1. 15.3.4.1 Single Request
        2. 15.3.4.2 Burst Request
      5. 15.3.5  Channel Configuration
      6. 15.3.6  Transfer Modes
        1. 15.3.6.1 Stop Mode
        2. 15.3.6.2 Basic Mode
        3. 15.3.6.3 Auto Mode
        4. 15.3.6.4 Ping-Pong
        5. 15.3.6.5 Memory Scatter-Gather Mode
        6. 15.3.6.6 Peripheral Scatter-Gather Mode
      7. 15.3.7  Transfer Size and Increments
      8. 15.3.8  Peripheral Interface
      9. 15.3.9  Software Request
      10. 15.3.10 Interrupts and Errors
    4. 15.4 Initialization and Configuration
      1. 15.4.1 Module Initialization
      2. 15.4.2 Configuring a Memory-to-Memory Transfer
        1. 15.4.2.1 Configure the Channel Attributes
        2. 15.4.2.2 Configure the Channel Control Structure
        3. 15.4.2.3 Start the Transfer
    5. 15.5 µDMA Registers
      1. 15.5.1 μDMA Registers
  16. 16Timers
    1. 16.1 General-Purpose Timers
    2. 16.2 Block Diagram
    3. 16.3 Functional Description
      1. 16.3.1 GPTM Reset Conditions
      2. 16.3.2 Timer Modes
        1. 16.3.2.1 One-Shot or Periodic Timer Mode
        2. 16.3.2.2 Input Edge-Count Mode
        3. 16.3.2.3 Input Edge-Time Mode
        4. 16.3.2.4 PWM Mode
        5. 16.3.2.5 Wait-for-Trigger Mode
      3. 16.3.3 Synchronizing GPT Blocks
      4. 16.3.4 Accessing Concatenated 16- and 32-Bit GPTM Register Values
    4. 16.4 Initialization and Configuration
      1. 16.4.1 One-Shot and Periodic Timer Modes
      2. 16.4.2 Input Edge-Count Mode
      3. 16.4.3 Input Edge-Timing Mode
      4. 16.4.4 PWM Mode
      5. 16.4.5 Producing DMA Trigger Events
    5. 16.5 GPTM Registers
      1. 16.5.1 GPT Registers
  17. 17Real-Time Clock (RTC)
    1. 17.1 Introduction
    2. 17.2 Functional Specifications
      1. 17.2.1 Functional Overview
      2. 17.2.2 Free-Running Counter
      3. 17.2.3 Channels
        1. 17.2.3.1 Capture and Compare
      4. 17.2.4 Events
    3. 17.3 RTC Register Information
      1. 17.3.1 Register Access
      2. 17.3.2 Entering Sleep and Wakeup From Sleep
      3. 17.3.3 AON_RTC:SYNC Register
    4. 17.4 RTC Registers
      1. 17.4.1 AON_RTC Registers
  18. 18Watchdog Timer (WDT)
    1. 18.1 Introduction
    2. 18.2 Functional Description
    3. 18.3 Initialization and Configuration
    4. 18.4 WDT Registers
      1. 18.4.1 WDT Registers
  19. 19True Random Number Generator (TRNG)
    1. 19.1 Introduction
    2. 19.2 Block Diagram
    3. 19.3 TRNG Software Reset
    4. 19.4 Interrupt Requests
    5. 19.5 TRNG Operation Description
      1. 19.5.1 TRNG Shutdown
      2. 19.5.2 TRNG Alarms
      3. 19.5.3 TRNG Entropy
    6. 19.6 TRNG Low-Level Programing Guide
      1. 19.6.1 Initialization
        1. 19.6.1.1 Interfacing Modules
        2. 19.6.1.2 TRNG Main Sequence
        3. 19.6.1.3 TRNG Operating Modes
          1. 19.6.1.3.1 Polling Mode
          2. 19.6.1.3.2 Interrupt Mode
    7. 19.7 TRNG Registers
      1. 19.7.1 TRNG Registers
  20. 20AUX Domain Peripherals
    1. 20.1 Introduction
      1. 20.1.1 AUX Block Diagram
    2. 20.2 Power and Clock Management
      1. 20.2.1 Operational Modes
        1. 20.2.1.1 Dual-Rate AUX Clock
      2. 20.2.2 Use Scenarios
        1. 20.2.2.1 MCU
      3. 20.2.3 SCE Clock Emulation
    3. 20.3 Digital Peripheral Modules
      1. 20.3.1 Overview
        1. 20.3.1.1 DDI Control-Configuration
      2. 20.3.2 AIODIO
        1. 20.3.2.1 Introduction
        2. 20.3.2.2 Functional Description
          1. 20.3.2.2.1 Mapping to DIO Pins
          2. 20.3.2.2.2 Configuration
          3. 20.3.2.2.3 GPIO Mode
          4. 20.3.2.2.4 Input Buffer
          5. 20.3.2.2.5 Data Output Source
      3. 20.3.3 SMPH
        1. 20.3.3.1 Introduction
        2. 20.3.3.2 Functional Description
        3. 20.3.3.3 Semaphore Allocation in TI Software
      4. 20.3.4 Time-to-Digital Converter (TDC)
        1. 20.3.4.1 Introduction
        2. 20.3.4.2 Functional Description
          1. 20.3.4.2.1 Command
          2. 20.3.4.2.2 Conversion Time Configuration
          3. 20.3.4.2.3 Status and Result
          4. 20.3.4.2.4 Clock Source Selection
            1. 20.3.4.2.4.1 Counter Clock
            2. 20.3.4.2.4.2 Reference Clock
          5. 20.3.4.2.5 Start and Stop Events
          6. 20.3.4.2.6 Prescaler
        3. 20.3.4.3 Supported Measurement Types
          1. 20.3.4.3.1 Measure Pulse Width
          2. 20.3.4.3.2 Measure Frequency
          3. 20.3.4.3.3 Measure Time Between Edges of Different Events Sources
            1. 20.3.4.3.3.1 Asynchronous Counter Start – Ignore 0 Stop Events
            2. 20.3.4.3.3.2 Synchronous Counter Start – Ignore 0 Stop Events
            3. 20.3.4.3.3.3 Asynchronous Counter Start – Ignore Stop Events
            4. 20.3.4.3.3.4 Synchronous Counter Start – Ignore Stop Events
          4. 20.3.4.3.4 Pulse Counting
      5. 20.3.5 Timer01
        1. 20.3.5.1 Introduction
        2. 20.3.5.2 Functional Description
    4. 20.4 Analog Peripheral Modules
      1. 20.4.1 Overview
        1. 20.4.1.1 ADI Control-Configuration
        2. 20.4.1.2 Block Diagram
      2. 20.4.2 Analog-to-Digital Converter (ADC)
        1. 20.4.2.1 Introduction
        2. 20.4.2.2 Functional Description
          1. 20.4.2.2.1 Input Selection and Scaling
          2. 20.4.2.2.2 Reference Selection
          3. 20.4.2.2.3 ADC Sample Mode
          4. 20.4.2.2.4 ADC Clock Source
          5. 20.4.2.2.5 ADC Trigger
          6. 20.4.2.2.6 Sample FIFO
          7. 20.4.2.2.7 µDMA Interface
          8. 20.4.2.2.8 Resource Ownership and Usage
      3. 20.4.3 COMPA
        1. 20.4.3.1 Introduction
        2. 20.4.3.2 Functional Description
          1. 20.4.3.2.1 Input Selection
          2. 20.4.3.2.2 Reference Selection
          3. 20.4.3.2.3 LPM Bias and COMPA Enable
          4. 20.4.3.2.4 Resource Ownership and Usage
      4. 20.4.4 COMPB
        1. 20.4.4.1 Introduction
        2. 20.4.4.2 Functional Description
          1. 20.4.4.2.1 Input Selection
          2. 20.4.4.2.2 Reference Selection
          3. 20.4.4.2.3 Resource Ownership and Usage
            1. 20.4.4.2.3.1 System CPU Wakeup
      5. 20.4.5 Reference DAC
        1. 20.4.5.1 Introduction
        2. 20.4.5.2 Functional Description
          1. 20.4.5.2.1 Reference Selection
          2. 20.4.5.2.2 Output Voltage Control and Range
          3. 20.4.5.2.3 Sample Clock
            1. 20.4.5.2.3.1 Automatic Phase Control
            2. 20.4.5.2.3.2 Manual Phase Control
            3. 20.4.5.2.3.3 Operational Mode Dependency
          4. 20.4.5.2.4 Output Selection
            1. 20.4.5.2.4.1 Buffer
            2. 20.4.5.2.4.2 External Load
            3. 20.4.5.2.4.3 COMPA_REF
            4. 20.4.5.2.4.4 COMPB_REF
          5. 20.4.5.2.5 LPM Bias
          6. 20.4.5.2.6 Resource Ownership and Usage
      6. 20.4.6 ISRC
        1. 20.4.6.1 Introduction
        2. 20.4.6.2 Functional Description
          1. 20.4.6.2.1 Programmable Current
          2. 20.4.6.2.2 Voltage Reference
          3. 20.4.6.2.3 ISRC Enable
          4. 20.4.6.2.4 Temperature Dependency
          5. 20.4.6.2.5 Resource Ownership and Usage
    5. 20.5 Event Routing and Usage
      1. 20.5.1 AUX Event Bus
        1. 20.5.1.1 Event Signals
        2. 20.5.1.2 Event Subscribers
          1. 20.5.1.2.1 Event Detection
            1. 20.5.1.2.1.1 Detection of Asynchronous Events
            2. 20.5.1.2.1.2 Detection of Synchronous Events
      2. 20.5.2 Event Observation on External Pin
      3. 20.5.3 Events From MCU Domain
      4. 20.5.4 Events to MCU Domain
      5. 20.5.5 Events From AON Domain
      6. 20.5.6 Events to AON Domain
      7. 20.5.7 µDMA Interface
    6. 20.6 AUX Domain Peripheral Registers
      1. 20.6.1 ADI_4_AUX Registers
      2. 20.6.2 AUX_AIODIO Registers
      3. 20.6.3 AUX_EVCTL Registers
      4. 20.6.4 AUX_SMPH Registers
      5. 20.6.5 AUX_TDC Registers
      6. 20.6.6 AUX_TIMER01 Registers
      7. 20.6.7 AUX_ANAIF Registers
      8. 20.6.8 AUX_SYSIF Registers
  21. 21Battery Monitor and Temperature Sensor (BATMON)
    1. 21.1 Introduction
    2. 21.2 Functional Description
    3. 21.3 BATMON Registers
      1. 21.3.1 AON_BATMON Registers
  22. 22Universal Asynchronous Receiver/Transmitter (UART)
    1. 22.1 Introduction
    2. 22.2 Block Diagram
    3. 22.3 Signal Description
    4. 22.4 Functional Description
      1. 22.4.1 Transmit and Receive Logic
      2. 22.4.2 Baud-rate Generation
      3. 22.4.3 Data Transmission
      4. 22.4.4 Modem Handshake Support
        1. 22.4.4.1 Signaling
        2. 22.4.4.2 Flow Control
          1. 22.4.4.2.1 Hardware Flow Control (RTS and CTS)
          2. 22.4.4.2.2 Software Flow Control (Modem Status Interrupts)
      5. 22.4.5 FIFO Operation
      6. 22.4.6 Interrupts
      7. 22.4.7 Loopback Operation
    5. 22.5 Interface to DMA
    6. 22.6 Initialization and Configuration
    7. 22.7 UART Registers
      1. 22.7.1 UART Registers
  23. 23Synchronous Serial Interface (SSI)
    1. 23.1 Introduction
    2. 23.2 Block Diagram
    3. 23.3 Signal Description
    4. 23.4 Functional Description
      1. 23.4.1 Bit Rate Generation
      2. 23.4.2 FIFO Operation
        1. 23.4.2.1 Transmit FIFO
        2. 23.4.2.2 Receive FIFO
      3. 23.4.3 Interrupts
      4. 23.4.4 Frame Formats
        1. 23.4.4.1 Texas Instruments Synchronous Serial Frame Format
        2. 23.4.4.2 Motorola SPI Frame Format
          1. 23.4.4.2.1 SPO Clock Polarity Bit
          2. 23.4.4.2.2 SPH Phase-Control Bit
        3. 23.4.4.3 Motorola SPI Frame Format With SPO = 0 and SPH = 0
        4. 23.4.4.4 Motorola SPI Frame Format With SPO = 0 and SPH = 1
        5. 23.4.4.5 Motorola SPI Frame Format With SPO = 1 and SPH = 0
        6. 23.4.4.6 Motorola SPI Frame Format With SPO = 1 and SPH = 1
        7. 23.4.4.7 MICROWIRE Frame Format
    5. 23.5 DMA Operation
    6. 23.6 Initialization and Configuration
    7. 23.7 SSI Registers
      1. 23.7.1 SSI Registers
  24. 24Inter-Integrated Circuit (I2C)
    1. 24.1 Introduction
    2. 24.2 Block Diagram
    3. 24.3 Functional Description
      1. 24.3.1 I2C Bus Functional Overview
        1. 24.3.1.1 Start and Stop Conditions
        2. 24.3.1.2 Data Format With 7-Bit Address
        3. 24.3.1.3 Data Validity
        4. 24.3.1.4 Acknowledge
        5. 24.3.1.5 Arbitration
      2. 24.3.2 Available Speed Modes
        1. 24.3.2.1 Standard and Fast Modes
      3. 24.3.3 Interrupts
        1. 24.3.3.1 I2C Master Interrupts
        2. 24.3.3.2 I2C Slave Interrupts
      4. 24.3.4 Loopback Operation
      5. 24.3.5 Command Sequence Flow Charts
        1. 24.3.5.1 I2C Master Command Sequences
        2. 24.3.5.2 I2C Slave Command Sequences
    4. 24.4 Initialization and Configuration
    5. 24.5 I2C Registers
      1. 24.5.1 I2C Registers
  25. 25Inter-IC Sound (I2S)
    1. 25.1 Introduction
    2. 25.2 Block Diagram
    3. 25.3 Signal Description
    4. 25.4 Functional Description
      1. 25.4.1 Dependencies
        1. 25.4.1.1 System CPU Deep-Sleep Mode
      2. 25.4.2 Pin Configuration
      3. 25.4.3 Serial Format Configuration
      4. 25.4.4 I2S
        1. 25.4.4.1 Register Configuration
      5. 25.4.5 Left-Justified (LJF)
        1. 25.4.5.1 Register Configuration
      6. 25.4.6 Right-Justified (RJF)
        1. 25.4.6.1 Register Configuration
      7. 25.4.7 DSP
        1. 25.4.7.1 Register Configuration
      8. 25.4.8 Clock Configuration
        1. 25.4.8.1 Internal Audio Clock Source
        2. 25.4.8.2 External Audio Clock Source
    5. 25.5 Memory Interface
      1. 25.5.1 Sample Word Length
      2. 25.5.2 Channel Mapping
      3. 25.5.3 Sample Storage in Memory
      4. 25.5.4 DMA Operation
        1. 25.5.4.1 Start-Up
        2. 25.5.4.2 Operation
        3. 25.5.4.3 Shutdown
    6. 25.6 Samplestamp Generator
      1. 25.6.1 Samplestamp Counters
      2. 25.6.2 Start-Up Triggers
      3. 25.6.3 Samplestamp Capture
      4. 25.6.4 Achieving Constant Audio Latency
    7. 25.7 Error Detection
    8. 25.8 Usage
      1. 25.8.1 Start-Up Sequence
      2. 25.8.2 Shutdown Sequence
    9. 25.9 I2S Registers
      1. 25.9.1 I2S Registers
  26. 26Radio
    1. 26.1  RF Core
      1. 26.1.1 High-Level Description and Overview
    2. 26.2  Radio Doorbell
      1. 26.2.1 Special Boot Process
      2. 26.2.2 Command and Status Register and Events
      3. 26.2.3 RF Core Interrupts
        1. 26.2.3.1 RF Command and Packet Engine Interrupts
        2. 26.2.3.2 RF Core Hardware Interrupts
        3. 26.2.3.3 RF Core Command Acknowledge Interrupt
      4. 26.2.4 Radio Timer
        1. 26.2.4.1 Compare and Capture Events
        2. 26.2.4.2 Radio Timer Outputs
        3. 26.2.4.3 Synchronization With Real-Time Clock
    3. 26.3  RF Core HAL
      1. 26.3.1 Hardware Support
      2. 26.3.2 Firmware Support
        1. 26.3.2.1 Commands
        2. 26.3.2.2 Command Status
        3. 26.3.2.3 Interrupts
        4. 26.3.2.4 Passing Data
        5. 26.3.2.5 Command Scheduling
          1. 26.3.2.5.1 Triggers
          2. 26.3.2.5.2 Conditional Execution
          3. 26.3.2.5.3 Handling Before Start of Command
        6. 26.3.2.6 Command Data Structures
          1. 26.3.2.6.1 Radio Operation Command Structure
        7. 26.3.2.7 Data Entry Structures
          1. 26.3.2.7.1 Data Entry Queue
          2. 26.3.2.7.2 Data Entry
          3. 26.3.2.7.3 Pointer Entry
          4. 26.3.2.7.4 Partial Read RX Entry
        8. 26.3.2.8 External Signaling
      3. 26.3.3 Command Definitions
        1. 26.3.3.1 Protocol-Independent Radio Operation Commands
          1. 26.3.3.1.1  CMD_NOP: No Operation Command
          2. 26.3.3.1.2  CMD_RADIO_SETUP: Set Up Radio Settings Command
          3. 26.3.3.1.3  CMD_FS_POWERUP: Power Up Frequency Synthesizer
          4. 26.3.3.1.4  CMD_FS_POWERDOWN: Power Down Frequency Synthesizer
          5. 26.3.3.1.5  CMD_FS: Frequency Synthesizer Controls Command
          6. 26.3.3.1.6  CMD_FS_OFF: Turn Off Frequency Synthesizer
          7. 26.3.3.1.7  CMD_RX_TEST: Receiver Test Command
          8. 26.3.3.1.8  CMD_TX_TEST: Transmitter Test Command
          9. 26.3.3.1.9  CMD_SYNC_STOP_RAT: Synchronize and Stop Radio Timer Command
          10. 26.3.3.1.10 CMD_SYNC_START_RAT: Synchronously Start Radio Timer Command
          11. 26.3.3.1.11 CMD_COUNT: Counter Command
          12. 26.3.3.1.12 CMD_SCH_IMM: Run Immediate Command as Radio Operation
          13. 26.3.3.1.13 CMD_COUNT_BRANCH: Counter Command With Branch of Command Chain
          14. 26.3.3.1.14 CMD_PATTERN_CHECK: Check a Value in Memory Against a Pattern
        2. 26.3.3.2 Protocol-Independent Direct and Immediate Commands
          1. 26.3.3.2.1  CMD_ABORT: ABORT Command
          2. 26.3.3.2.2  CMD_STOP: Stop Command
          3. 26.3.3.2.3  CMD_GET_RSSI: Read RSSI Command
          4. 26.3.3.2.4  CMD_UPDATE_RADIO_SETUP: Update Radio Settings Command
          5. 26.3.3.2.5  CMD_TRIGGER: Generate Command Trigger
          6. 26.3.3.2.6  CMD_GET_FW_INFO: Request Information on the Firmware Being Run
          7. 26.3.3.2.7  CMD_START_RAT: Asynchronously Start Radio Timer Command
          8. 26.3.3.2.8  CMD_PING: Respond With Interrupt
          9. 26.3.3.2.9  CMD_READ_RFREG: Read RF Core Register
          10. 26.3.3.2.10 CMD_SET_RAT_CMP: Set RAT Channel to Compare Mode
          11. 26.3.3.2.11 CMD_SET_RAT_CPT: Set RAT Channel to Capture Mode
          12. 26.3.3.2.12 CMD_DISABLE_RAT_CH: Disable RAT Channel
          13. 26.3.3.2.13 CMD_SET_RAT_OUTPUT: Set RAT Output to a Specified Mode
          14. 26.3.3.2.14 CMD_ARM_RAT_CH: Arm RAT Channel
          15. 26.3.3.2.15 CMD_DISARM_RAT_CH: Disarm RAT Channel
          16. 26.3.3.2.16 CMD_SET_TX_POWER: Set Transmit Power
          17. 26.3.3.2.17 CMD_SET_TX20_POWER: Set Transmit Power of the 20 dBm PA
          18. 26.3.3.2.18 CMD_UPDATE_FS: Set New Synthesizer Frequency Without Recalibration (Depricated)
          19. 26.3.3.2.19 CMD_MODIFY_FS: Set New Synthesizer Frequency Without Recalibration
          20. 26.3.3.2.20 CMD_BUS_REQUEST: Request System BUS Available for RF Core
      4. 26.3.4 Immediate Commands for Data Queue Manipulation
        1. 26.3.4.1 CMD_ADD_DATA_ENTRY: Add Data Entry to Queue
        2. 26.3.4.2 CMD_REMOVE_DATA_ENTRY: Remove First Data Entry From Queue
        3. 26.3.4.3 CMD_FLUSH_QUEUE: Flush Queue
        4. 26.3.4.4 CMD_CLEAR_RX: Clear All RX Queue Entries
        5. 26.3.4.5 CMD_REMOVE_PENDING_ENTRIES: Remove Pending Entries From Queue
    4. 26.4  Data Queue Usage
      1. 26.4.1 Operations on Data Queues Available Only for Internal Radio CPU Operations
        1. 26.4.1.1 PROC_ALLOCATE_TX: Allocate TX Entry for Reading
        2. 26.4.1.2 PROC_FREE_DATA_ENTRY: Free Allocated Data Entry
        3. 26.4.1.3 PROC_FINISH_DATA_ENTRY: Finish Use of First Data Entry From Queue
        4. 26.4.1.4 PROC_ALLOCATE_RX: Allocate RX Buffer for Storing Data
        5. 26.4.1.5 PROC_FINISH_RX: Commit Received Data to RX Data Entry
      2. 26.4.2 Radio CPU Usage Model
        1. 26.4.2.1 Receive Queues
        2. 26.4.2.2 Transmit Queues
    5. 26.5  IEEE 802.15.4
      1. 26.5.1 IEEE 802.15.4 Commands
        1. 26.5.1.1 IEEE 802.15.4 Radio Operation Command Structures
        2. 26.5.1.2 IEEE 802.15.4 Immediate Command Structures
        3. 26.5.1.3 Output Structures
        4. 26.5.1.4 Other Structures and Bit Fields
      2. 26.5.2 Interrupts
      3. 26.5.3 Data Handling
        1. 26.5.3.1 Receive Buffers
        2. 26.5.3.2 Transmit Buffers
      4. 26.5.4 Radio Operation Commands
        1. 26.5.4.1 RX Operation
          1. 26.5.4.1.1 Frame Filtering and Source Matching
            1. 26.5.4.1.1.1 Frame Filtering
            2. 26.5.4.1.1.2 Source Matching
          2. 26.5.4.1.2 Frame Reception
          3. 26.5.4.1.3 ACK Transmission
          4. 26.5.4.1.4 End of Receive Operation
          5. 26.5.4.1.5 CCA Monitoring
        2. 26.5.4.2 Energy Detect Scan Operation
        3. 26.5.4.3 CSMA-CA Operation
        4. 26.5.4.4 Transmit Operation
        5. 26.5.4.5 Receive Acknowledgment Operation
        6. 26.5.4.6 Abort Background-Level Operation Command
      5. 26.5.5 Immediate Commands
        1. 26.5.5.1 Modify CCA Parameter Command
        2. 26.5.5.2 Modify Frame-Filtering Parameter Command
        3. 26.5.5.3 Enable or Disable Source Matching Entry Command
        4. 26.5.5.4 Abort Foreground-Level Operation Command
        5. 26.5.5.5 Stop Foreground-Level Operation Command
        6. 26.5.5.6 Request CCA and RSSI Information Command
    6. 26.6  Bluetooth® low energy
      1. 26.6.1 Bluetooth® low energy Commands
        1. 26.6.1.1 Command Data Definitions
          1. 26.6.1.1.1 Bluetooth® low energy Command Structures
        2. 26.6.1.2 Parameter Structures
        3. 26.6.1.3 Output Structures
        4. 26.6.1.4 Other Structures and Bit Fields
      2. 26.6.2 Interrupts
    7. 26.7  Data Handling
      1. 26.7.1 Receive Buffers
      2. 26.7.2 Transmit Buffers
    8. 26.8  Radio Operation Command Descriptions
      1. 26.8.1  Bluetooth® 5 Radio Setup Command
      2. 26.8.2  Radio Operation Commands for Bluetooth® low energy Packet Transfer
      3. 26.8.3  Coding Selection for Coded PHY
      4. 26.8.4  Parameter Override
      5. 26.8.5  Link Layer Connection
      6. 26.8.6  Slave Command
      7. 26.8.7  Master Command
      8. 26.8.8  Legacy Advertiser
        1. 26.8.8.1 Connectable Undirected Advertiser Command
        2. 26.8.8.2 Connectable Directed Advertiser Command
        3. 26.8.8.3 Nonconnectable Advertiser Command
        4. 26.8.8.4 Scannable Undirected Advertiser Command
      9. 26.8.9  Bluetooth® 5 Advertiser Commands
        1. 26.8.9.1 Common Extended Advertising Packets
        2. 26.8.9.2 Extended Advertiser Command
        3. 26.8.9.3 Secondary Channel Advertiser Command
      10. 26.8.10 Scanner Commands
        1. 26.8.10.1 Scanner Receiving Legacy Advertising Packets on Primary Channel
        2. 26.8.10.2 Scanner Receiving Extended Advertising Packets on Primary Channel
        3. 26.8.10.3 Scanner Receiving Extended Advertising Packets on Secondary Channel
        4. 26.8.10.4 ADI Filtering
        5. 26.8.10.5 End of Scanner Commands
      11. 26.8.11 Initiator Command
        1. 26.8.11.1 Initiator Receiving Legacy Advertising Packets on Primary Channel
        2. 26.8.11.2 Initiator Receiving Extended Advertising Packets on Primary Channel
        3. 26.8.11.3 Initiator Receiving Extended Advertising Packets on Secondary Channel
        4. 26.8.11.4 Automatic Window Offset Insertion
        5. 26.8.11.5 End of Initiator Commands
      12. 26.8.12 Generic Receiver Command
      13. 26.8.13 PHY Test Transmit Command
      14. 26.8.14 Whitelist Processing
      15. 26.8.15 Backoff Procedure
      16. 26.8.16 AUX Pointer Processing
      17. 26.8.17 Dynamic Change of Device Address
    9. 26.9  Immediate Commands
      1. 26.9.1 Update Advertising Payload Command
    10. 26.10 Proprietary Radio
      1. 26.10.1 Packet Formats
      2. 26.10.2 Commands
        1. 26.10.2.1 Command Data Definitions
          1. 26.10.2.1.1 Command Structures
        2. 26.10.2.2 Output Structures
        3. 26.10.2.3 Other Structures and Bit Fields
      3. 26.10.3 Interrupts
      4. 26.10.4 Data Handling
        1. 26.10.4.1 Receive Buffers
        2. 26.10.4.2 Transmit Buffers
      5. 26.10.5 Radio Operation Command Descriptions
        1. 26.10.5.1 End of Operation
        2. 26.10.5.2 Proprietary Mode Setup Command
          1. 26.10.5.2.1 IEEE 802.15.4g Packet Format
        3. 26.10.5.3 Transmitter Commands
          1. 26.10.5.3.1 Standard Transmit Command, CMD_PROP_TX
          2. 26.10.5.3.2 Advanced Transmit Command, CMD_PROP_TX_ADV
        4. 26.10.5.4 Receiver Commands
          1. 26.10.5.4.1 Standard Receive Command, CMD_PROP_RX
          2. 26.10.5.4.2 Advanced Receive Command, CMD_PROP_RX_ADV
        5. 26.10.5.5 Carrier-Sense Operation
          1. 26.10.5.5.1 Common Carrier-Sense Description
          2. 26.10.5.5.2 Carrier-Sense Command, CMD_PROP_CS
          3. 26.10.5.5.3 Sniff Mode Receiver Commands, CMD_PROP_RX_SNIFF and CMD_PROP_RX_ADV_SNIFF
      6. 26.10.6 Immediate Commands
        1. 26.10.6.1 Set Packet Length Command, CMD_PROP_SET_LEN
        2. 26.10.6.2 Restart Packet RX Command, CMD_PROP_RESTART_RX
    11. 26.11 Radio Registers
      1. 26.11.1 RFC_RAT Registers
      2. 26.11.2 RFC_DBELL Registers
      3. 26.11.3 RFC_PWR Registers
        1.       Revision History

3.6.1 Arm® Cortex®-M4 Instructions

The processor implements the ARMv7-M Thumb instruction set. Table 3-25 lists the Arm® Cortex®-M4 instructions and their cycle counts. The cycle counts are based on a system with zero wait states.

Within the assembler syntax, depending on the operation, the <op2> field can be replaced with one of the following options:

  • A simple register specifier, for example 
    Rm
  • An immediate shifted register, for example 
    Rm, LSL #4
  • A register shifted register, for example 
    Rm, LSL Rs
  • An immediate value, for example 
    #0xE000E000

For brevity, not all load and store addressing modes are shown. See the ARMv7-M Architecture Reference Manual for more information.

Table 3-25 uses the following abbreviations in the Cycles column:

    PThe number of cycles required for a pipeline refill. This ranges from 1 to 3 depending on the alignment and width of the target instruction, and whether the processor manages to speculate the address early.
    BThe number of cycles required to perform the barrier operation. For DSB and DMB, the minimum number of cycles is zero. For ISB, the minimum number of cycles is equivalent to the number required for a pipeline refill.
    NThe number of registers in the register list to be loaded or stored, including PC or LR.
    WThe number of cycles spent waiting for an appropriate event.
Table 3-25 Arm® Cortex®-M4 Instruction Set Summary
OperationDescriptionAssemblerCycles
MoveRegister
MOV Rd, <op2>
1
16-bit immediate
MOVW Rd, #<imm>
1
Immediate into top
MOVT Rd, #<imm>
1
To PC
MOV PC, Rm
1 + P
AddAdd
ADD Rd, Rn, <op2>
1
Add to PC
ADD PC, PC, Rm
1 + P
Add with carry
ADC Rd, Rn, <op2>
1
Form address
ADR Rd, <label>
1
SubtractSubtract
SUB Rd, Rn, <op2>
1
Subtract with borrow
SBC Rd, Rn, <op2>
1
Reverse
RSB Rd, Rn, <op2>
1
MultiplyMultiply
MUL Rd, Rn, Rm
1
Multiply accumulate
MLA Rd, Rn, Rm
1
Multiply subtract
MLS Rd, Rn, Rm
1
Long signed
SMULL RdLo, RdHi, Rn, Rm
1
Long unsigned
UMULL RdLo, RdHi, Rn, Rm
1
Long signed accumulate
SMLAL RdLo, RdHi, Rn, Rm
1
Long unsigned accumulate
UMLAL RdLo, RdHi, Rn, Rm
1
DivideSigned
SDIV Rd, Rn, Rm
2 to 12(1)
Unsigned
UDIV Rd, Rn, Rm
2 to 12(1)
SaturateSigned
SSAT Rd, #<imm>, <op2>
1
Unsigned
USAT Rd, #<imm>, <op2>
1
CompareCompare
CMP Rn, <op2>
1
Negative
CMN Rn, <op2>
1
LogicalAND
AND Rd, Rn, <op2>
1
Exclusive OR
EOR Rd, Rn, <op2>
1
OR
ORR Rd, Rn, <op2>
1
OR NOT
ORN Rd, Rn, <op2>
1
Bit clear
BIC Rd, Rn, <op2>
1
Move NOT
MVN Rd, <op2>
1
AND test
TST Rn, <op2>
1
Exclusive OR test
TEQ Rn, <op1>
1
ShiftLogical shift left
LSL Rd, Rn, #<imm>
1
Logical shift left
LSL Rd, Rn, Rs
1
Logical shift right
LSR Rd, Rn, #<imm>
1
Logical shift right
LSR Rd, Rn, Rs
1
Arithmetic shift right
ASR Rd, Rn, #<imm>
1
Arithmetic shift right
ASR Rd, Rn, Rs
1
RotateRotate right
ROR Rd, Rn, #<imm>
1
Rotate right
ROR Rd, Rn, Rs
1
With extension
RRX Rd, Rn
1
CountLeading zeroes
CLZ Rd, Rn
1
LoadWord
LDR Rd, [Rn, <op2>]
2(2)
To PC
LDR PC, [Rn, <op2>]
2(2) + P
Halfword
LDRH Rd, [Rn, <op2>]
2(2)
Byte
LDRB Rd, [Rn, <op2>]
2(2)
Signed halfword
LDRSH Rd, [Rn, <op2>]
2(2)
Signed byte
LDRSB Rd, [Rn, <op2>]
2(2)
User word
LDRT Rd, [Rn, #<imm>]
2(2)
User halfword
LDRHT Rd, [Rn, #<imm>]
2(2)
User byte
LDRBT Rd, [Rn, #<imm>]
2(2)
User signed halfword
LDRSHT Rd, [Rn, #<imm>]
2(2)
User signed byte
LDRSBT Rd, [Rn, #<imm>]
2(2)
PC relative
LDR Rd,[PC, #<imm>]
2(2)
Doubleword
LDRD Rd, Rd, [Rn, #<imm>]
1 + N
Multiple
LDM Rn, {<reglist>}
1 + N
Multiple including PC
LDM Rn, {<reglist>, PC}
1 + N + P
StoreWord
STR Rd, [Rn, <op2>]
2(2)
Halfword
STRH Rd, [Rn, <op2>]
2(2)
Byte
STRB Rd, [Rn, <op2>]
2(2)
Signed halfword
STRSH Rd, [Rn, <op2>]
2(2)
Signed byte
STRSB Rd, [Rn, <op2>]
2(2)
User word
STRT Rd, [Rn, #<imm>]
2(2)
User halfword
STRHT Rd, [Rn, #<imm>]
2(2)
User byte
STRBT Rd, [Rn, #<imm>]
2(2)
User signed halfword
STRSHT Rd, [Rn, #<imm>]
2(2)
User signed byte
STRSBT Rd, [Rn, #<imm>]
2(2)
Doubleword
STRD Rd, Rd, [Rn, #<imm>]
1 + N
Multiple
STM Rn, {<reglist>}
1 + N
PushPush
PUSH {<reglist>}
1 + N
Push with link register
PUSH {<reglist>, LR}
1 + N
PopPop
POP {<reglist>}
1 + N
Pop and return
POP {<reglist>, PC}
1 + N + P
SemaphoreLoad exclusive
LDREX Rd, [Rn, #<imm>]
2
Load exclusive half
LDREXH Rd, [Rn]
2
Load exclusive byte
LDREXB Rd, [Rn]
2
Store exclusive
STREX Rd, Rt, [Rn,#<imm>]
2
Store exclusive half
STREXH Rd, Rt, [Rn]
2
Store exclusive byte
STREXB Rd, Rt, [Rn]
2
Clear exclusive monitor
CLREX
1
BranchConditional
B<cc> <label>
1 or 1 + P(3)
Unconditional
B <label>
1 + P
With link
BL <label>
1 + P
With exchange
BX Rm
1 + P
With link and exchange
BLX Rm
1 + P
Branch if zero
CBZ Rn, <label>
1 or 1 + P(3)
Branch if nonzero
CBNZ Rn, <label>
1 or 1 + P(3)
Byte table branch
TBB [Rn, Rm]
2 + P
Halfword table branch
TBH [Rn, Rm, LSL#1]
2 + P
State changeSupervisor call
SVC #<imm>
–
If-then-else
IT... <cond>
1(4)
Disable interrupts
CPSID <flags>
1 or 2
Enable interrupts
CPSIE <flags>
1 or 2
Read special register
MRS Rd, <specreg>
1 or 2
Write special register
MSR <specreg>, Rn
1 or 2
Breakpoint
BKPT #<imm>
–
ExtendSigned halfword to word
SXTH Rd, <op2>
1
Signed byte to word
SXTB Rd, <op2>
1
Unsigned halfword
UXTH Rd, <op2>
1
Unsigned byte
UXTB Rd, <op2>
1
Bit fieldExtract unsigned
UBFX Rd, Rn, #<imm>, #<imm>
1
Extract signed
SBFX Rd, Rn, #<imm>, #<imm>
1
Clear
BFC Rd, Rn, #<imm>, #<imm>
1
Insert
BFI Rd, Rn, #<imm>, #<imm>
1
ReverseBytes in word
REV Rd, Rm
1
Bytes in both halfwords
REV16 Rd, Rm
1
Signed bottom halfword
REVSH Rd, Rm
1
Bits in word
RBIT Rd, Rm
1
HintSend event
SEV
1
Wait for event
WFE
1 + W
Wait for interrupt
WFI
1 + W
No operation
NOP
1
BarriersInstruction synchronization
ISB
1 + B
Data memory
DMB
1 + B
Data synchronization
DSB <flags>
1 + B
(1) Division operations terminate when the divide calculation completes, with the number of cycles required dependent on the values of the input operands. Division operations are interruptible, meaning that an operation can be abandoned when an interrupt occurs, with worst case latency of one cycle, and restarted when the interrupt completes.
(2) Neighboring load and store single instructions can pipeline their address and data phases but in some cases such as 32-bit opcodes aligned on odd halfword boundaries they might not pipeline optimally.
(3) Conditional branch completes in a single cycle if the branch is not taken.
(4) An IT instruction can be folded onto a preceding 16-bit Thumb instruction, enabling execution in zero cycles.

Table 3-26 lists the DSP instructions that the Arm® Cortex®-M4 processor implements.

Table 3-26 Arm® Cortex®-M4 DSP Instruction Set Summary
OperationDescriptionAssemblerCycles
Multiply32 bit multiply with 32 most significant bit accumulate
SMMLA
1
32 bit multiply with 32 most significant bit subtract
SMMLS
1
32 bit multiply returning 32 most significant bits
SMMUL
1
32 bit multiply with rounded 32 most significant bit accumulate
SMMLAR
1
32 bit multiply with rounded 32 most significant bit subtract
SMMLSR
1
32 bit multiply returning rounded 32 most significant bits
SMMULR
1
Signed multiplyQ setting 16 bit signed multiply with 32 bit accumulate, bottom by bottom
SMLABB
1
Q setting 16 bit signed multiply with 32 bit accumulate, bottom by top
SMLABT
1
16 bit signed multiply with 64 bit accumulate, bottom by bottom
SMLALBB
1
16 bit signed multiply with 64 bit accumulate, bottom by top
SMLALBT
1
Dual 16 bit signed multiply with single 64 bit accumulator
SMLALD{X}
1
16 bit signed multiply with 64 bit accumulate, top by bottom
SMLALTB
1
16 bit signed multiply with 64 bit accumulate, top by top
SMLALTT
1
16 bit signed multiply yielding 32 bit result, bottom by bottom
SMULBB
1
16 bit signed multiply yielding 32 bit result, bottom by top
SMULBT
1
16 bit signed multiply yielding 32 bit result, top by bottom
SMULTB
1
16 bit signed multiply yielding 32 bit result, top by top
SMULTT
1
16 bit by 32 bit signed multiply returning 32 most significant bits, bottom
SMULWB
1
16 bit by 32 bit signed multiply returning 32 most significant bits, top
SMULWT
1
Dual 16 bit signed multiply returning difference
SMUSD{X}
1
Q setting 16 bit signed multiply with 32 bit accumulate, top by bottom
SMLATB
1
Q setting 16 bit signed multiply with 32 bit accumulate, top by top
SMLATT
1
Q setting dual 16 bit signed multiply with single 32 bit accumulator
SMLAD{X}
1
Q setting 16 bit by 32 bit signed multiply with 32 bit accumulate, bottom
SMLAWB
1
Q setting 16 bit by 32 bit signed multiply with 32 bit accumulate, top
SMLAWT
1
Q setting dual 16 bit signed multiply subtract with 32 bit accumulate
SMLSD{X}
1
Q setting dual 16 bit signed multiply subtract with 64 bit accumulate
SMLSLD{X}
1
Q setting sum of dual 16 bit signed multiply
SMUAD{X}
1
Unsigned multiply32 bit unsigned multiply with double 32 bit accumulation yielding 64 bit result
UMAAL
1
SaturateQ setting dual 16 bit saturate
SSAT16
1
Q setting dual 16 bit unsigned saturate
USAT16
1
Packing and unpackingPack halfword top with shifted bottom
PKHTB
Pack half word bottom with shifted top
PKHBT
1
Extract 8 bits and sign extend to 32 bits
SXTB
1
Dual extract 8 bits and sign extend each to 16 bits
SXTB16
1
Extract 16 bits and sign extend to 32 bits
SXTH
1
Extract 8 bits and zero-extend to 32 bits
UXTB
1
Dual extract 8 bits and zero-extend to 16 bits
UXTB16
1
Extract 16 bits and zero-extend to 32 bits
UXTH
1
Extract 8 bit to 32 bit unsigned addition
UXTAB
1
Dual extracted 8 bit to 16 bit unsigned addition
UXTAB16
1
Extracted 16 bit to 32 bit unsigned addition
UXTAH
1
Extracted 8 bit to 32 bit signed addition
SXTAB
1
Dual extracted 8 bit to 16 bit signed addition
SXTAB16
1
Extracted 16 bit to 32 bit signed addition
SXTAH
1
Miscellaneous data processingSelect bytes based on GE bits
SEL
1
Unsigned sum of quad 8 bit unsigned absolute difference
USAD8
1
Unsigned sum of quad 8 bit unsigned absolute difference with 32 bit accumulate
USADA8
1
AdditionDual 16 bit unsigned saturating addition
UQADD16
1
Quad 8 bit unsigned saturating addition
UQADD8
1
Q setting saturating add
QADD
1
Q setting dual 16 bit saturating add
QADD16
1
Q setting quad 8 bit saturating add
QADD8
1
Q setting saturating double and add
QDADD
1
GE setting quad 8 bit signed addition
SADD8
1
GE setting dual 16 bit signed addition
SADD16
1
Dual 16 bit signed addition with halved results
SHADD16
1
Quad 8 bit signed addition with halved results
SHADD8
1
GE setting dual 16 bit unsigned addition
UADD16
1
GE setting quad 8 bit unsigned addition
UADD8
1
Dual 16 bit unsigned addition with halved results
UHADD16
1
Quad 8 bit unsigned addition with halved results
UHADD8
1
SubtractionQ setting saturating double and subtract
QDSUB
1
Dual 16 bit unsigned saturating subtraction
UQSUB16
1
Quad 8 bit unsigned saturating subtraction
UQSUB8
1
Q setting saturating subtract
QSUB
1
Q setting dual 16 bit saturating subtract
QSUB16
1
Q setting quad 8 bit saturating subtract
QSUB8
1
Dual 16 bit signed subtraction with halved results
SHSUB16
1
Quad 8 bit signed subtraction with halved results
SHSUB8
1
GE setting dual 16 bit signed subtraction
SSUB16
1
GE setting quad 8 bit signed subtraction
SSUB8
1
Dual 16 bit unsigned subtraction with halved results
UHSUB16
1
Quad 8 bit unsigned subtraction with halved results
UHSUB8
1
GE setting dual 16 bit unsigned subtract
USUB16
1
GE setting quad 8 bit unsigned subtract
USUB8
1
Parallel addition and subtractionDual 16 bit unsigned saturating addition and subtraction with exchange
UQASX
1
Dual 16 bit unsigned saturating subtraction and addition with exchange
UQSAX
1
GE setting dual 16 bit addition and subtraction with exchange
SASX
1
Q setting dual 16 bit add and subtract with exchange
QASX
1
Q setting dual 16 bit subtract and add with exchange
QSAX
1
Dual 16 bit signed addition and subtraction with halved results
SHASX
1
Dual 16 bit signed subtraction and addition with halved results
SHSAX
1
GE setting dual 16 bit signed subtraction and addition with exchange
SSAX
1
GE setting dual 16 bit unsigned addition and subtraction with exchange
UASX
1
Dual 16 bit unsigned addition and subtraction with halved results and exchange
UHASX
1
Dual 16 bit unsigned subtraction and addition with halved results and exchange
UHSAX
1
GE setting dual 16 bit unsigned subtract and add with exchange
USAX
1