ZHCSTD3B June   2022  – October 2023 BQ756506-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 说明（续）
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Power Supplies
        1. 8.3.1.1 AVAO_REF and AVDD_REF
        2. 8.3.1.2 LDOIN
        3. 8.3.1.3 AVDD
        4. 8.3.1.4 DVDD
        5. 8.3.1.5 CVDD and NEG5V
        6. 8.3.1.6 TSREF
      2. 8.3.2 Measurement System
        1. 8.3.2.1 Main ADC
          1. 8.3.2.1.1 Cell Voltage Measurements
            1. 8.3.2.1.1.1 Analog Front End
            2. 8.3.2.1.1.2 VC Channel Measurements
            3. 8.3.2.1.1.3 Post-ADC Digital LPF
            4. 8.3.2.1.1.4 SRP and SRN Measurements
          2. 8.3.2.1.2 Temperature Measurements
            1. 8.3.2.1.2.1 DieTemp1 Measurement
            2. 8.3.2.1.2.2 GPIOs and TSREF Measurements
          3. 8.3.2.1.3 Main ADC Operation Control
            1. 8.3.2.1.3.1 Operation Modes and Status
        2. 8.3.2.2 AUX ADC
          1. 8.3.2.2.1 AUX Cell Voltage Measurements
            1. 8.3.2.2.1.1 AUX Analog Front End
            2. 8.3.2.2.1.2 CB and Current Sense Channel Measurements
          2. 8.3.2.2.2 AUX Temperature Measurements
            1. 8.3.2.2.2.1 DieTemp2 Measurement
            2. 8.3.2.2.2.2 AUX GPIO Measurements
          3. 8.3.2.2.3 MISC Measurements
          4. 8.3.2.2.4 AUX ADC Operation Control
        3. 8.3.2.3 Synchronization Between MAIN and AUX ADC Measurements
        4. 8.3.2.4 CS ADC
      3. 8.3.3 Cell Balancing
        1. 8.3.3.1 Set Up Cell Balancing
          1. 8.3.3.1.1 Step 1: Determine Balancing Channels
          2. 8.3.3.1.2 Step 2: Select Balancing Control Methods
          3. 8.3.3.1.3 Step 3a: Balancing Thermal Management
          4. 8.3.3.1.4 Step 3b: Option to Stop On Cell Voltage Threshold
          5. 8.3.3.1.5 Step 3c: Option to Stop at Fault
        2. 8.3.3.2 Cell Balancing in SLEEP Mode
        3. 8.3.3.3 Pause and Stop Cell Balancing
          1. 8.3.3.3.1 Cell Balancing Pause
          2. 8.3.3.3.2 Cell Balancing Stop
          3. 8.3.3.3.3 Remaining CB Time
      4. 8.3.4 Integrated Hardware Protectors
        1. 8.3.4.1 OVUV Protectors
          1. 8.3.4.1.1 OVUV Operation Modes
          2. 8.3.4.1.2 OVUV Control and Status
            1. 8.3.4.1.2.1 OVUV Control
            2. 8.3.4.1.2.2 OVUV Status
        2. 8.3.4.2 OTUT Protector
          1. 8.3.4.2.1 OTUT Operation Modes
          2. 8.3.4.2.2 OTUT Control and Status
            1. 8.3.4.2.2.1 OTUT Control
            2. 8.3.4.2.2.2 OTUT Status
      5. 8.3.5 GPIO Configuration
      6. 8.3.6 Communication, OTP, Diagnostic Control
        1. 8.3.6.1 Communication
          1. 8.3.6.1.1 Serial Interface
            1. 8.3.6.1.1.1 UART Physical Layer
              1. 8.3.6.1.1.1.1 UART Transmitter
              2. 8.3.6.1.1.1.2 UART Receiver
              3. 8.3.6.1.1.1.3 COMM CLEAR
            2. 8.3.6.1.1.2 Command and Response Protocol
              1. 8.3.6.1.1.2.1 Transaction Frame Structure
                1. 8.3.6.1.1.2.1.1 Frame Initialization Byte
                2. 8.3.6.1.1.2.1.2 Device Address Byte
                3. 8.3.6.1.1.2.1.3 Register Address Bytes
                4. 8.3.6.1.1.2.1.4 Data Bytes
                5. 8.3.6.1.1.2.1.5 CRC Bytes
                6. 8.3.6.1.1.2.1.6 Calculating Frame CRC Value
                7. 8.3.6.1.1.2.1.7 Verifying Frame CRC
              2. 8.3.6.1.1.2.2 Transaction Frame Examples
                1. 8.3.6.1.1.2.2.1 Single Device Read/Write
          2. 8.3.6.1.2 Communication Timeout
            1. 8.3.6.1.2.1 Short Communication Timeout
            2. 8.3.6.1.2.2 Long Communication Timeout
          3. 8.3.6.1.3 SPI Controller
          4. 8.3.6.1.4 SPI Loopback
        2. 8.3.6.2 Fault Handling
          1. 8.3.6.2.1 Fault Status Hierarchy
            1. 8.3.6.2.1.1 Debug Registers
          2. 8.3.6.2.2 Fault Masking and Reset
            1. 8.3.6.2.2.1 Fault Masking
            2. 8.3.6.2.2.2 Fault Reset
          3. 8.3.6.2.3 Fault Signaling
        3. 8.3.6.3 Nonvolatile Memory
          1. 8.3.6.3.1 OTP Page Status
          2. 8.3.6.3.2 OTP Programming
        4. 8.3.6.4 Diagnostic Control/Status
          1. 8.3.6.4.1 Power Supplies Check
            1. 8.3.6.4.1.1 Power Supply Diagnostic Check
            2. 8.3.6.4.1.2 Power Supply BIST
          2. 8.3.6.4.2 Thermal Shutdown and Warning Check
            1. 8.3.6.4.2.1 Thermal Shutdown
            2. 8.3.6.4.2.2 Thermal Warning
          3. 8.3.6.4.3 Oscillators Watchdog
          4. 8.3.6.4.4 OTP Error Check
            1. 8.3.6.4.4.1 OTP CRC Test and Faults
            2. 8.3.6.4.4.2 OTP Margin Read
            3. 8.3.6.4.4.3 Error Check and Correct (ECC) OTP
          5. 8.3.6.4.5 Integrated Hardware Protector Check
            1. 8.3.6.4.5.1 Parity Check
            2. 8.3.6.4.5.2 OVUV and OTUT DAC Check
            3. 8.3.6.4.5.3 OVUV Protector BIST
            4. 8.3.6.4.5.4 OTUT Protector BIST
          6. 8.3.6.4.6 Diagnostic Through ADC Comparison
            1. 8.3.6.4.6.1 Cell Voltage Measurement Check
            2. 8.3.6.4.6.2 Temperature Measurement Check
            3. 8.3.6.4.6.3 Cell Balancing FETs Check
            4. 8.3.6.4.6.4 VC and CB Open Wire Check
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power Modes
        1. 8.4.1.1 SHUTDOWN Mode
          1. 8.4.1.1.1 Exit SHUTDOWN Mode
          2. 8.4.1.1.2 Enter SHUTDOWN Mode
        2. 8.4.1.2 SLEEP Mode
          1. 8.4.1.2.1 Exit SLEEP Mode
          2. 8.4.1.2.2 Enter SLEEP Mode
        3. 8.4.1.3 ACTIVE Mode
          1. 8.4.1.3.1 Exit ACTIVE Mode
          2. 8.4.1.3.2 Enter ACTIVE Mode From SHUTDOWN Mode
          3. 8.4.1.3.3 Enter ACTIVE Mode From SLEEP Mode
      2. 8.4.2 Device Reset
      3. 8.4.3 Ping
        1. 8.4.3.1 Ping
    5. 8.5 Register Maps
      1. 8.5.1 OTP Shadow Register Summary
      2. 8.5.2 Read/Write Register Summary
      3. 8.5.3 Read-Only Register Summary
      4. 8.5.4 Register Field Descriptions
        1. 8.5.4.1  Device Addressing Setup
          1. 8.5.4.1.1 DIR0_ADDR_OTP
          2. 8.5.4.1.2 DIR1_ADDR_OTP
          3. 8.5.4.1.3 CUST_MISC1 through CUST_MISC8
          4. 8.5.4.1.4 DIR0_ADDR
          5. 8.5.4.1.5 DIR1_ADDR
        2. 8.5.4.2  Device ID and Scratch Pad
          1. 8.5.4.2.1 PARTID
          2. 8.5.4.2.2 DEV_REVID
          3. 8.5.4.2.3 DIE_ID1 through DIE_ID9
        3. 8.5.4.3  General Configuration and Control
          1. 8.5.4.3.1  DEV_CONF
          2. 8.5.4.3.2  ACTIVE_CELL
          3. 8.5.4.3.3  PWR_TRANSIT_CONF
          4. 8.5.4.3.4  COMM_TIMEOUT_CONF
          5. 8.5.4.3.5  TX_HOLD_OFF
          6. 8.5.4.3.6  COMM_CTRL
          7. 8.5.4.3.7  CONTROL1
          8. 8.5.4.3.8  CONTROL2
          9. 8.5.4.3.9  CUST_CRC_HI
          10. 8.5.4.3.10 CUST_CRC_LO
          11. 8.5.4.3.11 CUST_CRC_RSLT_HI
          12. 8.5.4.3.12 CUST_CRC_RSLT_LO
        4. 8.5.4.4  Operation Status
          1. 8.5.4.4.1 DIAG_STAT
          2. 8.5.4.4.2 ADC_STAT1
          3. 8.5.4.4.3 ADC_STAT2
          4. 8.5.4.4.4 GPIO_STAT
          5. 8.5.4.4.5 BAL_STAT
          6. 8.5.4.4.6 DEV_STAT
        5. 8.5.4.5  ADC Configuration and Control
          1. 8.5.4.5.1  ADC_CONF1
          2. 8.5.4.5.2  ADC_CONF2
          3. 8.5.4.5.3  MAIN_ADC_CAL1
          4. 8.5.4.5.4  MAIN_ADC_CAL2
          5. 8.5.4.5.5  AUX_ADC_CAL1
          6. 8.5.4.5.6  AUX_ADC_CAL2
          7. 8.5.4.5.7  CS_ADC_CAL1
          8. 8.5.4.5.8  CS_ADC_CAL2
          9. 8.5.4.5.9  ADC_CTRL1
          10. 8.5.4.5.10 ADC_CTRL2
          11. 8.5.4.5.11 ADC_CTRL3
        6. 8.5.4.6  ADC Measurement Results
          1. 8.5.4.6.1  VCELL6_HI/LO
          2. 8.5.4.6.2  VCELL5_HI/LO
          3. 8.5.4.6.3  VCELL4_HI/LO
          4. 8.5.4.6.4  VCELL3_HI/LO
          5. 8.5.4.6.5  VCELL2_HI/LO
          6. 8.5.4.6.6  VCELL1_HI/LO
          7. 8.5.4.6.7  MAIN_CURRENT_HI/LO
          8. 8.5.4.6.8  CURRENT_HI/MID/LO
          9. 8.5.4.6.9  TSREF_HI/LO
          10. 8.5.4.6.10 GPIO1_HI/LO
          11. 8.5.4.6.11 GPIO2_HI/LO
          12. 8.5.4.6.12 GPIO3_HI/LO
          13. 8.5.4.6.13 GPIO4_HI/LO
          14. 8.5.4.6.14 GPIO5_HI/LO
          15. 8.5.4.6.15 GPIO6_HI/LO
          16. 8.5.4.6.16 GPIO7_HI/LO
          17. 8.5.4.6.17 GPIO8_HI/LO
          18. 8.5.4.6.18 DIETEMP1_HI/LO
          19. 8.5.4.6.19 DIETEMP2_HI/LO
          20. 8.5.4.6.20 AUX_CELL_HI/LO
          21. 8.5.4.6.21 AUX_GPIO_HI/LO
          22. 8.5.4.6.22 AUX_BAT_HI/LO
          23. 8.5.4.6.23 AUX_REFL_HI/LO
          24. 8.5.4.6.24 AUX_VBG2_HI/LO
          25. 8.5.4.6.25 AUX_AVAO_REF_HI/LO
          26. 8.5.4.6.26 AUX_AVDD_REF_HI/LO
          27. 8.5.4.6.27 AUX_OV_DAC_HI/LO
          28. 8.5.4.6.28 AUX_UV_DAC_HI/LO
          29. 8.5.4.6.29 AUX_OT_OTCB_DAC_HI/LO
          30. 8.5.4.6.30 AUX_UT_DAC_HI/LO
          31. 8.5.4.6.31 AUX_VCBDONE_DAC_HI/LO
          32. 8.5.4.6.32 AUX_VCM_HI/LO
          33. 8.5.4.6.33 REFOVDAC_HI/LO
          34. 8.5.4.6.34 DIAG_MAIN_HI/LO
          35. 8.5.4.6.35 DIAG_AUX_HI/LO
        7. 8.5.4.7  Balancing Configuration, Control and Status
          1. 8.5.4.7.1 CB_CELL6_CTRL through CB_CELL1_CTRL
          2. 8.5.4.7.2 VCB_DONE_THRESH
          3. 8.5.4.7.3 OTCB_THRESH
          4. 8.5.4.7.4 BAL_CTRL1
          5. 8.5.4.7.5 BAL_CTRL2
          6. 8.5.4.7.6 BAL_CTRL3
          7. 8.5.4.7.7 CB_COMPLETE2
          8. 8.5.4.7.8 BAL_TIME
        8. 8.5.4.8  Protector Configuration and Control
          1. 8.5.4.8.1 OV_THRESH
          2. 8.5.4.8.2 UV_THRESH
          3. 8.5.4.8.3 UV_DISABLE2
          4. 8.5.4.8.4 OTUT_THRESH
          5. 8.5.4.8.5 OVUV_CTRL
          6. 8.5.4.8.6 OTUT_CTRL
        9. 8.5.4.9  GPIO Configuration
          1. 8.5.4.9.1 GPIO_CONF1
          2. 8.5.4.9.2 GPIO_CONF2
          3. 8.5.4.9.3 GPIO_CONF3
          4. 8.5.4.9.4 GPIO_CONF4
        10. 8.5.4.10 SPI Controller
          1. 8.5.4.10.1 SPI_CONF
          2. 8.5.4.10.2 SPI_EXE
          3. 8.5.4.10.3 SPI_TX3, SPI_TX2, and SPI_TX1
          4. 8.5.4.10.4 SPI_RX3, SPI_RX2, and SPI_RX1
        11. 8.5.4.11 Diagnostic Control
          1. 8.5.4.11.1 DIAG_OTP_CTRL
          2. 8.5.4.11.2 DIAG_COMM_CTRL
          3. 8.5.4.11.3 DIAG_PWR_CTRL
          4. 8.5.4.11.4 DIAG_CBFET_CTRL2
          5. 8.5.4.11.5 DIAG_COMP_CTRL1
          6. 8.5.4.11.6 DIAG_COMP_CTRL2
          7. 8.5.4.11.7 DIAG_COMP_CTRL3
          8. 8.5.4.11.8 DIAG_COMP_CTRL4
          9. 8.5.4.11.9 DIAG_PROT_CTRL
        12. 8.5.4.12 Fault Configuration and Reset
          1. 8.5.4.12.1 FAULT_MSK1
          2. 8.5.4.12.2 FAULT_MSK2
          3. 8.5.4.12.3 FAULT_RST1
          4. 8.5.4.12.4 FAULT_RST2
        13. 8.5.4.13 Fault Status
          1. 8.5.4.13.1  FAULT_SUMMARY
          2. 8.5.4.13.2  FAULT_COMM1
          3. 8.5.4.13.3  FAULT_OTP
          4. 8.5.4.13.4  FAULT_SYS
          5. 8.5.4.13.5  FAULT_PROT1
          6. 8.5.4.13.6  FAULT_PROT2
          7. 8.5.4.13.7  FAULT_OV2
          8. 8.5.4.13.8  FAULT_UV2
          9. 8.5.4.13.9  FAULT_OT
          10. 8.5.4.13.10 FAULT_UT
          11. 8.5.4.13.11 FAULT_COMP_GPIO
          12. 8.5.4.13.12 FAULT_COMP_VCCB2
          13. 8.5.4.13.13 FAULT_COMP_VCOW2
          14. 8.5.4.13.14 FAULT_COMP_CBOW2
          15. 8.5.4.13.15 FAULT_COMP_CBFET2
          16. 8.5.4.13.16 FAULT_COMP_MISC
          17. 8.5.4.13.17 FAULT_PWR1
          18. 8.5.4.13.18 FAULT_PWR2
          19. 8.5.4.13.19 FAULT_PWR3
        14. 8.5.4.14 Debug Control and Status
          1. 8.5.4.14.1 DEBUG_UART_RC
          2. 8.5.4.14.2 DEBUG_UART_RR_TR
          3. 8.5.4.14.3 DEBUG_UART_DISCARD
          4. 8.5.4.14.4 DEBUG_UART_VALID_HI/LO
          5. 8.5.4.14.5 DEBUG_OTP_SEC_BLK
          6. 8.5.4.14.6 DEBUG_OTP_DED_BLK
        15. 8.5.4.15 OTP Programming Control and Status
          1. 8.5.4.15.1 OTP_PROG_UNLOCK1A through OTP_PROG_UNLOCK1D
          2. 8.5.4.15.2 OTP_PROG_UNLOCK2A through OTP_PROG_UNLOCK2D
          3. 8.5.4.15.3 OTP_PROG_CTRL
          4. 8.5.4.15.4 OTP_ECC_TEST
          5. 8.5.4.15.5 OTP_ECC_DATAIN1 through OTP_ECC_DATAIN9
          6. 8.5.4.15.6 OTP_ECC_DATAOUT1 through OTP_ECC_DATAOUT9
          7. 8.5.4.15.7 OTP_PROG_STAT
          8. 8.5.4.15.8 OTP_CUST1_STAT
          9. 8.5.4.15.9 OTP_CUST2_STAT
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Application Circuits
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Cell Sensing and Balancing Inputs
          2. 9.2.1.2.2 Synchronize Voltage and Current Measurements
          3. 9.2.1.2.3 BAT and External NPN
          4. 9.2.1.2.4 Power Supplies, Reference Input
          5. 9.2.1.2.5 GPIO For Thermistor Inputs
          6. 9.2.1.2.6 Internal Balancing Current
          7. 9.2.1.2.7 UART, NFAULT
          8. 9.2.1.2.8 Current Sense Input
        3. 9.2.1.3 Application Curve
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Ground Planes
      2. 11.1.2 Bypass Capacitors for Power Supplies and Reference
      3. 11.1.3 Cell Voltage Sensing
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 第三方产品免责声明
    2. 12.2 接收文档更新通知
    3. 12.3 支持资源
    4. 12.4 Trademarks
    5. 12.5 静电放电警告
    6. 12.6 术语表
  14. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
8.5.4.11.7 DIAG_COMP_CTRL3
Address0x033C
RWBit 7Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1Bit 0
NameRSVDCBFET_CTRL_GOOW_SNK[1:0]COMP_ADC_SEL[2:0]COMP_ADC _GO
Reset00000000
RSVD =Reserved
CBFET_CTRL_GO =When this GO bit = 1, device turns on the CBFET configured and turns off whichever CBFET is clear in DIAG_CBFET_CTRL2 register. This GO action is executed only if CB is not running or it’s in pause, otherwise, CBFETs are controlled by regular CB control.
If CBFET are turned on by this GO bit, once CB is started or resume, the CBFET controls returns to the regular CB control (and not by this GO bit action)
OW_SNK[1:0] =Turns on current sink on VC pins, CB pins. Changes to these bits take effect immediately. Host MCU is responsible to turn on the correct sink current before performing open wire (OW) test and to turn off the sink current after OW test is completed.
00 = All VC, , CB pins current sink is off. SRP/N current source is off
01 = Turn on current sink on all VC pins
10 = Turn on current sink on all CB pins
11 = Turn on current source on SRP/N pins
COMP_ADC_SEL[2:0] =Enables the device diagnostic comparison through the ADC measurements. Host enables the corresponding ADCs in continuous mode before enabling this diagnostic. These bits are sampled when [COMP_ADC_GO] = 1.
000 = No ADC comparison is performed
001 = Cell voltage measurement check.
Device compares the cell channels specified by [AUX_CELL_SEL4:0] against the following criteria:
VCELL (from Main ADC) vs. AUXCELL (from AUX ADC) delta is less than [VCCB_THR4:0].
The [DRDY_VCCB] = 1 when this comparison is completed.
010 = Open wire (OW) check on VC pins.
MCU enables the current sink on all VC pins through the [OW_SNK1:0] before enabling this comparison. Device compares corresponding VC pins specified by ACTIVE_CELL register against the following criteria: VCELL (from Main ADC) is less than DIAG_COMP_CTRL2 [OW_THR3:0].
The [DRDY_VC_OW] = 1 when the comparison is completed.
011 = Open wire (OW) check on CB pins
MCU enables the current sink on all VC pins through the [OW_SNK1:0] before enabling this comparison. Device compares corresponding CB pins specified by [AUX_CELL_SEL4:0] against the following criteria: AUXCELL (from AUX ADC) is less than DIAG_COMP_CTRL2 [OW_THR3:0]. The [DRDY_CBOW] = 1 when the comparison is completed.
100 = CBFET check.
MCU preconfigures the following before starting this check:
  • Pause cell balancing if balancing is enabled.
  • Enable the CBFET configured by DIAG_CBFET_CTRL2 register.
  • Configure the [EXTD_CBFET] to decide if all CBFET returns to pause state (that is, turn off all CBFET) or remains their status as specified by DIAG_CBFET_CTRL2 register.
When this test starts, device will turn on CBFET specified by DIAG_CBFET_CTRL2 register and then compares the channel specified by [AUX_CELL_SEL4:0] with the following criteria:
AUXCELL (from AUX ADC) < 1/3 of VCELL (from Main ADC). [DRDY_CBFET] = 1 when the comparison is completed.
101 = GPIO measurement check (applies to GPIO configured as ADC and OTUT inputs or ADC only input).
Device compares main GPIO measurement vs. AUX GPIO measurements delta is less than [GPIO_THR2:0]. The [DRDY_GPIO] = 1 when the comparison is completed.
Other codes: No ADC comparison is performed
COMP_ADC_GO =Device starts diagnostic test specified by [COMP_ADC_SEL2:0] setting. When this bit is written to 1, the selected [COMP_ADC_SEL2:0] is sampled. Change of [COMP_ADC_SEL2:0] setting has no effect unless this GO bit is written to 1 again.
This bit is cleared to 0 in read.
0 = Ready. Writing 0 has no effect
1 = Star diagnostic selected by [COMP_ADC_SEL2:0]