ZHCSP40B October   2021  – June 2022 LMX2571-EP

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Timing Diagrams
    8. 6.8 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Differences Between the LMX2571 and LMX2571-EP
      2. 7.3.2  Reference Oscillator Input
      3. 7.3.3  R-Dividers and Multiplier
      4. 7.3.4  PLL Phase Detector and Charge Pump
        1. 7.3.4.1 CPout Pin Charge Pump Current
        2. 7.3.4.2 Charge Pump Current When Using External VCO
      5. 7.3.5  PLL N-Divider and Fractional Circuitry
      6. 7.3.6  Partially Integrated Loop Filter
      7. 7.3.7  Low-Noise, Fully Integrated VCO
      8. 7.3.8  External VCO Support
      9. 7.3.9  Programmable RF Output Divider
      10. 7.3.10 Programmable RF Output Buffer
      11. 7.3.11 Integrated TX, RX Switch
      12. 7.3.12 Power Down
      13. 7.3.13 Lock Detect
      14. 7.3.14 FSK Modulation
      15. 7.3.15 FastLock
      16. 7.3.16 Register Readback
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation Mode
      2. 7.4.2 Duplex Mode
      3. 7.4.3 FSK Mode
    5. 7.5 Programming
      1. 7.5.1 Recommended Initial Power on Programming Sequence
      2. 7.5.2 Recommended Sequence for Changing Frequencies
    6. 7.6 Register Maps
      1. 7.6.1  R60 Register (offset = 3Ch) [reset = 4000h]
      2. 7.6.2  R58 Register (offset = 3Ah) [reset = C00h]
      3. 7.6.3  R53 Register (offset = 35h) [reset = 2802h]
      4. 7.6.4  R47 Register (offset = 2Fh) [reset = 0h]
      5. 7.6.5  R46 Register (offset = 2Eh) [reset = 1Ah]
      6. 7.6.6  R42 Register (offset = 2Ah) [reset = 210h]
      7. 7.6.7  R41 Register (offset = 29h) [reset = 810h]
      8. 7.6.8  R40 Register (offset = 28h) [reset = 101Ch]
      9. 7.6.9  R39 Register (offset = 27h) [reset = 11F0h]
      10. 7.6.10 R35 Register (offset = 23h) [reset = 647h]
      11. 7.6.11 R34 Register (offset = 22h) [reset = 1000h]
      12. 7.6.12 R33 Register (offset = 21h) [reset = 0h]
      13. 7.6.13 R25 to R32 Register (offset = 19h to 20h) [reset = 0h]
      14. 7.6.14 R24 Register (offset = 18h) [reset = 10h]
      15. 7.6.15 R23 Register (offset = 17h) [reset = 10A4h]
      16. 7.6.16 R22 Register (offset = 16h) [reset = 8584h]
      17. 7.6.17 R21 Register (offset = 15h) [reset = 101h]
      18. 7.6.18 R20 Register (offset = 14h) [reset = 28h]
      19. 7.6.19 R19 Register (offset = 13h) [reset = 0h]
      20. 7.6.20 R18 Register (offset = 12h) [reset = 0h]
      21. 7.6.21 R17 Register (offset = 11h) [reset = 0h]
      22. 7.6.22 R9 to R16 Register (offset = 9h to 10h) [reset = 0h]
      23. 7.6.23 R8 Register (offset = 8h) [reset = 10h]
      24. 7.6.24 R7 Register (offset = 7h) [reset = 10A4h]
      25. 7.6.25 R6 Register (offset = 6h) [reset = 8584h]
      26. 7.6.26 R5 Register (offset = 5h) [reset = 101h]
      27. 7.6.27 R4 Register (offset = 4h) [reset = 28h]
      28. 7.6.28 R3 Register (offset = 3h) [reset = 0h]
      29. 7.6.29 R2 Register (offset = 2h) [reset = 0h]
      30. 7.6.30 R1 Register (offset = 1h) [reset = 0h]
      31. 7.6.31 R0 Register (offset = 0h) [reset = 3h]
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1  Direct Digital FSK Modulation
      2. 8.1.2  Frequency and Output Port Switching
      3. 8.1.3  OSCin Configuration
      4. 8.1.4  Register R0 F1F2_INIT, F1F2_MODE Usage
      5. 8.1.5  FastLock With External VCO
      6. 8.1.6  OSCin Slew Rate
      7. 8.1.7  RF Output Buffer Power Control
      8. 8.1.8  RF Output Buffer Type
      9. 8.1.9  MULT Multiplier
      10. 8.1.10 Integrated VCO
    2. 8.2 Typical Applications
      1. 8.2.1 Synthesizer Duplex Mode
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Synthesizer Duplex Mode Application Curves
      2. 8.2.2 PLL Duplex Mode
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
        3. 8.2.2.3 PLL Duplex Mode Application Curves
      3. 8.2.3 Synthesizer/PLL Duplex Mode
        1. 8.2.3.1 Design Requirements
        2. 8.2.3.2 Detailed Design Procedure
        3. 8.2.3.3 Synthesizer/PLL Duplex Mode Application Curves
    3. 8.3 Do's and Don'ts
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Development Support
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 接收文档更新通知
    4. 11.4 支持资源
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 术语表
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.2.2.2 Detailed Design Procedure

Again, we need to figure out all the frequencies in each functional block first.

GUID-7420F2BD-98A2-4849-888C-9641CCD11EEB-low.gifFigure 8-23 Frequency Plan in PLL Duplex Mode

Follow the previous example to determine all the necessary configurations. Table 8-10 is the summary in this example.

Table 8-10 PLL Duplex Mode Frequency Plan Summary
CONFIGURATION PARAMETERF1 (430 MHz)F2 (480 MHz)
Pre-divider11
MULT55
Post-divider33
PDF28 MHz28 MHz
VCO430 MHz480 MHz
N-divider15.3571428617.14285714
Ninteger1517
DEN12345671234567
NUM440917176367

To enable external VCO operation, set the following bits:

Table 8-11 PLL Duplex Mode Register Settings Summary
CONFIGURATION PARAMETERREGISTER BITSSETTING
Charge pump polarityEXTVCO_CP_POL0 = Positive
External VCO charge pump gainEXTVCO_CP_GAIN1 = 1x
Base charge pump currentEXTVCO_CP_IUP8 = 1250 µA
EXTVCO_CP_IDN8 = 1250 µA
Select PLL mode operationEXTVCO_SEL_F1, EXTVCO_SEL_F21 = External VCO
CHDIV3 dividerEXTVCO_CHDIV_F1, EXTVCO_CHDIV_F20 = Bypass

Make sure that register R0, FCAL_EN is set so that FastLock is enabled.

The loop bandwidth had been design to be around 4 kHz, while phase margin is about 40 degrees.