ZHCSP40B October   2021  – June 2022 LMX2571-EP

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Timing Diagrams
    8. 6.8 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Differences Between the LMX2571 and LMX2571-EP
      2. 7.3.2  Reference Oscillator Input
      3. 7.3.3  R-Dividers and Multiplier
      4. 7.3.4  PLL Phase Detector and Charge Pump
        1. 7.3.4.1 CPout Pin Charge Pump Current
        2. 7.3.4.2 Charge Pump Current When Using External VCO
      5. 7.3.5  PLL N-Divider and Fractional Circuitry
      6. 7.3.6  Partially Integrated Loop Filter
      7. 7.3.7  Low-Noise, Fully Integrated VCO
      8. 7.3.8  External VCO Support
      9. 7.3.9  Programmable RF Output Divider
      10. 7.3.10 Programmable RF Output Buffer
      11. 7.3.11 Integrated TX, RX Switch
      12. 7.3.12 Power Down
      13. 7.3.13 Lock Detect
      14. 7.3.14 FSK Modulation
      15. 7.3.15 FastLock
      16. 7.3.16 Register Readback
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation Mode
      2. 7.4.2 Duplex Mode
      3. 7.4.3 FSK Mode
    5. 7.5 Programming
      1. 7.5.1 Recommended Initial Power on Programming Sequence
      2. 7.5.2 Recommended Sequence for Changing Frequencies
    6. 7.6 Register Maps
      1. 7.6.1  R60 Register (offset = 3Ch) [reset = 4000h]
      2. 7.6.2  R58 Register (offset = 3Ah) [reset = C00h]
      3. 7.6.3  R53 Register (offset = 35h) [reset = 2802h]
      4. 7.6.4  R47 Register (offset = 2Fh) [reset = 0h]
      5. 7.6.5  R46 Register (offset = 2Eh) [reset = 1Ah]
      6. 7.6.6  R42 Register (offset = 2Ah) [reset = 210h]
      7. 7.6.7  R41 Register (offset = 29h) [reset = 810h]
      8. 7.6.8  R40 Register (offset = 28h) [reset = 101Ch]
      9. 7.6.9  R39 Register (offset = 27h) [reset = 11F0h]
      10. 7.6.10 R35 Register (offset = 23h) [reset = 647h]
      11. 7.6.11 R34 Register (offset = 22h) [reset = 1000h]
      12. 7.6.12 R33 Register (offset = 21h) [reset = 0h]
      13. 7.6.13 R25 to R32 Register (offset = 19h to 20h) [reset = 0h]
      14. 7.6.14 R24 Register (offset = 18h) [reset = 10h]
      15. 7.6.15 R23 Register (offset = 17h) [reset = 10A4h]
      16. 7.6.16 R22 Register (offset = 16h) [reset = 8584h]
      17. 7.6.17 R21 Register (offset = 15h) [reset = 101h]
      18. 7.6.18 R20 Register (offset = 14h) [reset = 28h]
      19. 7.6.19 R19 Register (offset = 13h) [reset = 0h]
      20. 7.6.20 R18 Register (offset = 12h) [reset = 0h]
      21. 7.6.21 R17 Register (offset = 11h) [reset = 0h]
      22. 7.6.22 R9 to R16 Register (offset = 9h to 10h) [reset = 0h]
      23. 7.6.23 R8 Register (offset = 8h) [reset = 10h]
      24. 7.6.24 R7 Register (offset = 7h) [reset = 10A4h]
      25. 7.6.25 R6 Register (offset = 6h) [reset = 8584h]
      26. 7.6.26 R5 Register (offset = 5h) [reset = 101h]
      27. 7.6.27 R4 Register (offset = 4h) [reset = 28h]
      28. 7.6.28 R3 Register (offset = 3h) [reset = 0h]
      29. 7.6.29 R2 Register (offset = 2h) [reset = 0h]
      30. 7.6.30 R1 Register (offset = 1h) [reset = 0h]
      31. 7.6.31 R0 Register (offset = 0h) [reset = 3h]
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1  Direct Digital FSK Modulation
      2. 8.1.2  Frequency and Output Port Switching
      3. 8.1.3  OSCin Configuration
      4. 8.1.4  Register R0 F1F2_INIT, F1F2_MODE Usage
      5. 8.1.5  FastLock With External VCO
      6. 8.1.6  OSCin Slew Rate
      7. 8.1.7  RF Output Buffer Power Control
      8. 8.1.8  RF Output Buffer Type
      9. 8.1.9  MULT Multiplier
      10. 8.1.10 Integrated VCO
    2. 8.2 Typical Applications
      1. 8.2.1 Synthesizer Duplex Mode
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Synthesizer Duplex Mode Application Curves
      2. 8.2.2 PLL Duplex Mode
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
        3. 8.2.2.3 PLL Duplex Mode Application Curves
      3. 8.2.3 Synthesizer/PLL Duplex Mode
        1. 8.2.3.1 Design Requirements
        2. 8.2.3.2 Detailed Design Procedure
        3. 8.2.3.3 Synthesizer/PLL Duplex Mode Application Curves
    3. 8.3 Do's and Don'ts
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Development Support
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 接收文档更新通知
    4. 11.4 支持资源
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 术语表
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.6.31 R0 Register (offset = 0h) [reset = 3h]

Figure 7-37 R0 Register
1514131211109876543210
00RESETPOWERDOWN00F1F2_INIT0F1F2_MODEF1F2_SEL00001FCAL_EN
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-1hR/W-1h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 7-36 R0 Register Field Descriptions
BITFIELDTYPERESETDESCRIPTION
15-14R/W0h

Program 0h to this field.

13RESETR/W0h

Resets all the registers to the default values. This bit is self-clearing.
0 = Normal operation
1 = Reset

12POWERDOWNR/W0h

Powers down the device. When the device comes out of the powered down state, either by resuming this bit to zero or by pulling back CE pin HIGH (if it was powered down by CE pin), it is required that register R0 with FCAL_EN = 1 be programmed again to re-calibrate the device. A 100-µs wait-time is recommended before programming R0.
0 = Normal operation
1 = Power down

11R/W0h

Program this field to 0h.

10R/W0h

Program this field to 0h.

9F1F2_INITR/W0h

Toggling this bit re-calibrates F1F2 if F1, F2 are modified after calibration. This bit is not self-clear, so it is required to clear the bit value after use. See Section 8.1.4 for details.
0 = Clear bit value
1 = Re-calibrate

8R/W0h

Program this field to 0h.

7F1F2_MODER/W0h

Calibrates F1 and F2 during device initialization (initial power on programming). Even if this bit is not set, F1-F2 switching is still possible but the first switching time will not be optimized because either F1 or F2 will only be calibrated. If F1-F2 switching is not required, set this bit to zero. See Section 8.1.4 for details.
0 = Disable F1F2 calibration
1 = Enable F1F2 calibration

6F1F2_SELR/W0h

Selects F1 or F2 configuration registers.
0 = F1 registers
1 = F2 registers

5-1R/W1h

Program 1h to this field.

0FCAL_ENR/W1h

Activates all kinds of calibrations, suggest keep it enabled all the time. If it is desired that the R0 register be programmed without activating this calibration, then this bit can be set to zero.
0 = Disabled
1 = Enabled