ZHCSR89A December   2022  – August 2023 ADS131B23

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Timing Diagram
    9. 6.9 Typical Characteristics
  8. 7 Parameter Measurement Information
    1. 7.1 Offset Drift Measurement
    2. 7.2 Gain Drift Measurement
    3. 7.3 Noise Performance
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Naming Conventions
      2. 8.3.2 Precision Voltage References (REFA, REFB)
      3. 8.3.3 Clocking (MCLK, OSCM, OSCD)
      4. 8.3.4 ADC1y
        1. 8.3.4.1 ADC1y Input Multiplexer
        2. 8.3.4.2 ADC1y Programmable Gain Amplifier (PGA)
        3. 8.3.4.3 ADC1y ΔΣ Modulator
        4. 8.3.4.4 ADC1y Digital Filter
        5. 8.3.4.5 ADC1y Offset and Gain Calibration
        6. 8.3.4.6 ADC1y Conversion Data
      5. 8.3.5 ADC2y
        1. 8.3.5.1 ADC2y Input Multiplexer
        2. 8.3.5.2 ADC2y Programmable Gain Amplifier (PGA)
        3. 8.3.5.3 ADC2y ΔΣ Modulator
        4. 8.3.5.4 ADC2y Digital Filter
        5. 8.3.5.5 ADC2y Offset and Gain Calibration
        6. 8.3.5.6 ADC2y Sequencer
        7. 8.3.5.7 VCMy Buffers
        8. 8.3.5.8 ADC2y Measurement Configurations
        9. 8.3.5.9 ADC2y Conversion Data
      6. 8.3.6 General-Purpose Digital Inputs and Outputs (GPIO0 to GPIO4)
        1. 8.3.6.1 GPIOx PWM Output Configuration
        2. 8.3.6.2 GPIOx PWM Input Readback
      7. 8.3.7 General-Purpose Digital Inputs and Outputs (GPIO0A, GPIO1A, GPIO0B, GPIO1B)
      8. 8.3.8 Monitors and Diagnostics
        1. 8.3.8.1  Supply Monitors
        2. 8.3.8.2  Clock Monitors
        3. 8.3.8.3  Digital Monitors
          1. 8.3.8.3.1 Register Map CRC
          2. 8.3.8.3.2 Memory Map CRC
          3. 8.3.8.3.3 GPIO Readback
        4. 8.3.8.4  Communication Monitors
        5. 8.3.8.5  Fault Flags and Fault Masking
        6. 8.3.8.6  FAULT Pin
        7. 8.3.8.7  Diagnostics and Diagnostic Procedure
        8. 8.3.8.8  Indicators
        9. 8.3.8.9  Conversion and Sequence Counters
        10. 8.3.8.10 Supply Voltage Readback
        11. 8.3.8.11 Temperature Sensor (TSA)
        12. 8.3.8.12 Test DACs (TDACA, TDACB)
        13. 8.3.8.13 Open-Wire Detection
        14. 8.3.8.14 Missing Host Detection and MHD Pin
        15. 8.3.8.15 Overcurrent Comparators (OCCA, OCCB)
          1. 8.3.8.15.1 OCCA and OCCB Pins
          2. 8.3.8.15.2 Overcurrent Indication Response Time
    4. 8.4 器件功能模式
      1. 8.4.1 Power-Up and Reset
        1. 8.4.1.1 Power-On Reset (POR)
        2. 8.4.1.2 RESETn Pin
        3. 8.4.1.3 RESET Command
      2. 8.4.2 Operating Modes
        1. 8.4.2.1 Active Mode
        2. 8.4.2.2 Standby Mode
        3. 8.4.2.3 Power-Down Mode
      3. 8.4.3 ADC Conversion Modes
        1. 8.4.3.1 ADC1y Conversion Modes
          1. 8.4.3.1.1 Continuous-Conversion Mode
          2. 8.4.3.1.2 Single-Shot Conversion Mode
          3. 8.4.3.1.3 Global-Chop Mode
            1. 8.4.3.1.3.1 Overcurrent Indication Response Time in Global-Chop Mode
        2. 8.4.3.2 ADC2y Sequencer Operation and Sequence Modes
          1. 8.4.3.2.1 Continuous Sequence Mode
          2. 8.4.3.2.2 Single-Shot Sequence Mode
          3. 8.4.3.2.3 Synchronized Single-Shot Sequence Mode Based on ADC1y Conversion Starts
    5. 8.5 Programming
      1. 8.5.1 Serial Interface
        1. 8.5.1.1 Serial Interface Signals
          1. 8.5.1.1.1 Chip Select (CSn)
          2. 8.5.1.1.2 Serial Data Clock (SCLK)
          3. 8.5.1.1.3 Serial Data Input (SDI)
          4. 8.5.1.1.4 Serial Data Output (SDO)
          5. 8.5.1.1.5 Data Ready (DRDYn)
        2. 8.5.1.2 Serial Interface Communication Structure
          1. 8.5.1.2.1 SPI Communication Frames
          2. 8.5.1.2.2 SPI Communication Words
          3. 8.5.1.2.3 STATUS Word
          4. 8.5.1.2.4 Communication Cyclic Redundancy Check (CRC)
          5. 8.5.1.2.5 Commands
            1. 8.5.1.2.5.1 NULL (0000 0000 0000 0000b)
            2. 8.5.1.2.5.2 RESET (0000 0000 0001 0001b)
            3. 8.5.1.2.5.3 LOCK (0000 0101 0101 0101b)
            4. 8.5.1.2.5.4 UNLOCK (0000 0110 0101 0101b)
            5. 8.5.1.2.5.5 WREG (011a aaaa aaa0 0nnnb)
            6. 8.5.1.2.5.6 RREG (101a aaaa aaan nnnnb)
          6. 8.5.1.2.6 SCLK Counter
          7. 8.5.1.2.7 SPI Timeout
          8. 8.5.1.2.8 Reading ADC1A, ADC1B, and ADC2A Conversion Data
          9. 8.5.1.2.9 DRDYn Pin Behavior
    6. 8.6 Register Map
      1. 8.6.1 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Unused Inputs and Outputs
      2. 9.1.2 Minimum Interface Connections
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Current-Shunt Measurement
        2. 9.2.2.2 Battery-Pack Voltage Measurement
        3. 9.2.2.3 Shunt Temperature Measurement
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 Power-Supply Options
        1. 9.3.1.1 Single Unregulated External 4-V to 16-V Supply (3.3-V Digital I/O Levels)
        2. 9.3.1.2 Single Regulated External 3.3-V Supply (3.3-V Digital IO Levels)
        3. 9.3.1.3 Single Regulated External 5-V Supply (5-V Digital I/O Levels)
      2. 9.3.2 Power-Supply Sequencing
      3. 9.3.3 Power-Supply Decoupling
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10器件和文档支持
    1. 10.1 文档支持
      1. 10.1.1 相关文档
    2. 10.2 接收文档更新通知
    3. 10.3 支持资源
    4. 10.4 商标
    5. 10.5 静电放电警告
    6. 10.6 术语表
  12. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息
8.4.3.2.1 Continuous Sequence Mode

In continuous sequence mode, the ADC2y sequencer runs through the configured sequence over and over again until stopped by the host. Set the respective SEQ2y_START bit in the CONVERSION_CTRL register to start the sequencer of ADC2y. Setting the SEQ2y_START bit while the sequencer is running aborts the ongoing sequence run and restarts a new sequence run from the beginning. Use the SEQ2y_STOP bit to stop the sequencer of ADC2y. The currently ongoing sequence run is allowed to finish after the SEQ2y_STOP bit is set. After setting the SEQ2y_STOP bit, the SEQ2y_STOP bit reads back 1b until the sequencer stopped. Disabling ADC2y or putting the device into standby or power-down mode aborts the sequence run immediately.

The SEQ2y_START bits take priority over the SEQ2y_STOP bits. That means if both the SEQ2y_START and SEQ2y_STOP bits in the CONVERSION_CTRL register are set at the same time, then the sequencer starts a sequence run or aborts an ongoing sequence run and starts a new sequence run from the beginning.

The last conversion results of an ADC2y sequence run are still available for readout after the sequencer stopped. The conversion results of the sequencer are only cleared to 0000h after a device reset, when the ADC is disabled, when the device is in standby or power-down mode, or are overwritten when conversion results from a new sequence run become available.