ZHCSNC8A February   2021  – March 2021 TPS541620

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Fixed-Frequency, Internally Compensated Advanced-Current-Mode Control
      2. 7.3.2  Enable and UVLO
      3. 7.3.3  Internal LDO
      4. 7.3.4  Pre-biased Output Start-up
      5. 7.3.5  Current Sharing
      6. 7.3.6  Frequency Selection and Minimum On-Time and Off-Time
      7. 7.3.7  Ramp Compensation Selection
      8. 7.3.8  Soft Start
      9. 7.3.9  Remote Sense Function
      10. 7.3.10 Adjustable Output Voltage
      11. 7.3.11 Power Good
      12. 7.3.12 Overcurrent Protection
      13. 7.3.13 Overvoltage and Undervoltage Protection
      14. 7.3.14 Overtemperature Protection
      15. 7.3.15 Frequency Synchronization
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation Mode
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application - Dual Independent Outputs
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Switching Frequency
        2. 8.2.2.2  Output Inductor Selection
        3. 8.2.2.3  Output Capacitor
        4. 8.2.2.4  Input Capacitor
        5. 8.2.2.5  Output Voltage Resistors Selection
        6. 8.2.2.6  Adjustable Undervoltage Lockout
        7. 8.2.2.7  Bootstrap Capacitor Selection
        8. 8.2.2.8  BP5 Capacitor Selection
        9. 8.2.2.9  PGOOD Pullup Resistor
        10. 8.2.2.10 Current Limit
        11. 8.2.2.11 Soft-Start Time Selection
        12. 8.2.2.12 MODE1 and MODE2 Pins
      3. 8.2.3 Application Curves
      4. 8.2.4 Typical Application - 2-Phase Operation
        1. 8.2.4.1 Design Requirements
        2. 8.2.4.2 Detailed Design Procedure
          1. 8.2.4.2.1  Switching Frequency
          2. 8.2.4.2.2  Output Inductor Selection
          3. 8.2.4.2.3  Output Capacitor
          4. 8.2.4.2.4  Input Capacitor
          5. 8.2.4.2.5  Output Voltage Resistors Selection
          6. 8.2.4.2.6  Adjustable Undervoltage Lockout
          7. 8.2.4.2.7  Bootstrap Capacitor Selection
          8. 8.2.4.2.8  BP5 Capacitor Selection
          9. 8.2.4.2.9  PGOOD Pullup Resistor
          10. 8.2.4.2.10 Current Limit
          11. 8.2.4.2.11 Soft-Start Time Selection
          12. 8.2.4.2.12 MODE1 Pin
        3. 8.2.4.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
      1. 10.2.1 Thermal Performance
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 第三方产品免责声明
    2. 11.2 接收文档更新通知
    3. 11.3 支持资源
    4. 11.4 Trademarks
    5. 11.5 静电放电警告
    6. 11.6 术语表
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.3.6 Frequency Selection and Minimum On-Time and Off-Time

Switching frequency for the TPS541620 can be configured through the MODE2 pin on the device. The options available to you are the following:

  • 500 kHz
  • 1 MHz
  • 1.5 MHz
  • 2.0 MHz
Selecting the appropriate resistor from Table 7-1 sets one of the four options, as well as the ramp capacitor value for compensation.

The device has a minimum on-time of 40 ns (typ.) and a minimum off-time of 150 ns (typ.). Pay attention in applications with minimum duty cycle at high input voltage and maximum duty cycle at low input voltage. The minimum on-time and minimum off-time constrain the output voltage regulation in steady state operation. The device pulse skips if the input voltage, output voltage, and switching frequency require an on-time that is smaller than the minimum controllable on-time of 40 ns. Similarly, the device will operate in dropout when the input voltage, output voltage, and switching frequency require a lower off-time than the controllable off-time of 150 ns. The user must always stay away from operating beyond Ton_min and Toff_min conditions.