ZHCSSS9A march   2023  – august 2023 AM62A3 , AM62A3-Q1 , AM62A7 , AM62A7-Q1

PRODUCTION DATA  

  1.   1
  2. 特性
  3. 应用
  4. 说明
    1. 3.1 Functional Block Diagram
  5. Revision History
  6. Device Comparison
    1. 5.1 Related Products
  7. Terminal Configuration and Functions
    1. 6.1 Pin Diagrams
    2. 6.2 Pin Attributes
      1.      12
      2.      13
    3. 6.3 Signal Descriptions
      1.      15
      2. 6.3.1  CPSW3G
        1. 6.3.1.1 MAIN Domain
          1.        18
          2.        19
          3.        20
          4.        21
      3. 6.3.2  CPTS
        1. 6.3.2.1 MAIN Domain
          1.        24
      4. 6.3.3  CSI-2
        1. 6.3.3.1 MAIN Domain
          1.        27
      5. 6.3.4  DDRSS
        1. 6.3.4.1 MAIN Domain
          1.        30
      6. 6.3.5  DSS
        1. 6.3.5.1 MAIN Domain
          1.        33
      7. 6.3.6  ECAP
        1. 6.3.6.1 MAIN Domain
          1.        36
          2.        37
          3.        38
      8. 6.3.7  Emulation and Debug
        1. 6.3.7.1 MAIN Domain
          1.        41
        2. 6.3.7.2 MCU Domain
          1.        43
      9. 6.3.8  EPWM
        1. 6.3.8.1 MAIN Domain
          1.        46
          2.        47
          3.        48
          4.        49
      10. 6.3.9  EQEP
        1. 6.3.9.1 MAIN Domain
          1.        52
          2.        53
          3.        54
      11. 6.3.10 GPIO
        1. 6.3.10.1 MAIN Domain
          1.        57
          2.        58
        2. 6.3.10.2 MCU Domain
          1.        60
      12. 6.3.11 GPMC
        1. 6.3.11.1 MAIN Domain
          1.        63
      13. 6.3.12 I2C
        1. 6.3.12.1 MAIN Domain
          1.        66
          2.        67
          3.        68
          4.        69
        2. 6.3.12.2 MCU Domain
          1.        71
        3. 6.3.12.3 WKUP Domain
          1.        73
      14. 6.3.13 MCAN
        1. 6.3.13.1 MAIN Domain
          1.        76
        2. 6.3.13.2 MCU Domain
          1.        78
          2.        79
      15. 6.3.14 MCASP
        1. 6.3.14.1 MAIN Domain
          1.        82
          2.        83
          3.        84
      16. 6.3.15 MCSPI
        1. 6.3.15.1 MAIN Domain
          1.        87
          2.        88
          3.        89
        2. 6.3.15.2 MCU Domain
          1.        91
          2.        92
      17. 6.3.16 MDIO
        1. 6.3.16.1 MAIN Domain
          1.        95
      18. 6.3.17 MMC
        1. 6.3.17.1 MAIN Domain
          1.        98
          2.        99
          3.        100
      19. 6.3.18 OSPI
        1. 6.3.18.1 MAIN Domain
          1.        103
      20. 6.3.19 Power Supply
        1.       105
      21. 6.3.20 Reserved
        1.       107
      22. 6.3.21 System and Miscellaneous
        1. 6.3.21.1 Boot Mode Configuration
          1. 6.3.21.1.1 MAIN Domain
            1.         111
        2. 6.3.21.2 Clock
          1. 6.3.21.2.1 MCU Domain
            1.         114
          2. 6.3.21.2.2 WKUP Domain
            1.         116
        3. 6.3.21.3 System
          1. 6.3.21.3.1 MAIN Domain
            1.         119
          2. 6.3.21.3.2 MCU Domain
            1.         121
          3. 6.3.21.3.3 WKUP Domain
            1.         123
        4. 6.3.21.4 VMON
          1.        125
      23. 6.3.22 TIMER
        1. 6.3.22.1 MAIN Domain
          1.        128
        2. 6.3.22.2 MCU Domain
          1.        130
        3. 6.3.22.3 WKUP Domain
          1.        132
      24. 6.3.23 UART
        1. 6.3.23.1 MAIN Domain
          1.        135
          2.        136
          3.        137
          4.        138
          5.        139
          6.        140
          7.        141
        2. 6.3.23.2 MCU Domain
          1.        143
        3. 6.3.23.3 WKUP Domain
          1.        145
      25. 6.3.24 USB
        1. 6.3.24.1 MAIN Domain
          1.        148
          2.        149
    4. 6.4 Pin Connectivity Requirements
  8. Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Power-On Hours (POH)
    4. 7.4  Recommended Operating Conditions
    5. 7.5  Operating Performance Points
    6. 7.6  Power Consumption Summary
    7. 7.7  Electrical Characteristics
      1. 7.7.1 I2C Open-Drain, and Fail-Safe (I2C OD FS) Electrical Characteristics
      2. 7.7.2 Fail-Safe Reset (FS RESET) Electrical Characteristics
      3. 7.7.3 High-Frequency Oscillator (HFOSC) Electrical Characteristics
      4. 7.7.4 Low-Frequency Oscillator (LFXOSC) Electrical Characteristics
      5. 7.7.5 SDIO Electrical Characteristics
      6. 7.7.6 LVCMOS Electrical Characteristics
      7. 7.7.7 CSI-2 (D-PHY) Electrical Characteristics
      8. 7.7.8 USB2PHY Electrical Characteristics
      9. 7.7.9 DDR Electrical Characteristics
    8. 7.8  VPP Specifications for One-Time Programmable (OTP) eFuses
      1. 7.8.1 Recommended Operating Conditions for OTP eFuse Programming
      2. 7.8.2 Hardware Requirements
      3. 7.8.3 Programming Sequence
      4. 7.8.4 Impact to Your Hardware Warranty
    9. 7.9  Thermal Resistance Characteristics
      1. 7.9.1 Thermal Resistance Characteristics for AMB Package
    10. 7.10 Timing and Switching Characteristics
      1. 7.10.1 Timing Parameters and Information
      2. 7.10.2 Power Supply Requirements
        1. 7.10.2.1 Power Supply Slew Rate Requirement
        2. 7.10.2.2 Power Supply Sequencing
          1. 7.10.2.2.1 Power-Up Sequencing
          2. 7.10.2.2.2 Power-Down Sequencing
          3. 7.10.2.2.3 Partial IO Power Sequencing
      3. 7.10.3 System Timing
        1. 7.10.3.1 Reset Timing
        2. 7.10.3.2 Error Signal Timing
        3. 7.10.3.3 Clock Timing
      4. 7.10.4 Clock Specifications
        1. 7.10.4.1 Input Clocks / Oscillators
          1. 7.10.4.1.1 MCU_OSC0 Internal Oscillator Clock Source
            1. 7.10.4.1.1.1 Load Capacitance
            2. 7.10.4.1.1.2 Shunt Capacitance
          2. 7.10.4.1.2 MCU_OSC0 LVCMOS Digital Clock Source
          3. 7.10.4.1.3 WKUP_LFOSC0 Internal Oscillator Clock Source
          4. 7.10.4.1.4 WKUP_LFOSC0 LVCMOS Digital Clock Source
          5. 7.10.4.1.5 WKUP_LFOSC0 Not Used
        2. 7.10.4.2 Output Clocks
        3. 7.10.4.3 PLLs
        4. 7.10.4.4 Recommended System Precautions for Clock and Control Signal Transitions
      5. 7.10.5 Peripherals
        1. 7.10.5.1  CPSW3G
          1. 7.10.5.1.1 CPSW3G MDIO Timing
          2. 7.10.5.1.2 CPSW3G RMII Timing
          3. 7.10.5.1.3 CPSW3G RGMII Timing
        2. 7.10.5.2  CPTS
        3. 7.10.5.3  CSI-2
        4. 7.10.5.4  DDRSS
        5. 7.10.5.5  DSS
        6. 7.10.5.6  ECAP
        7. 7.10.5.7  Emulation and Debug
          1. 7.10.5.7.1 Trace
          2. 7.10.5.7.2 JTAG
        8. 7.10.5.8  EPWM
        9. 7.10.5.9  EQEP
        10. 7.10.5.10 GPIO
        11. 7.10.5.11 GPMC
          1. 7.10.5.11.1 GPMC and NOR Flash — Synchronous Mode
          2. 7.10.5.11.2 GPMC and NOR Flash — Asynchronous Mode
          3. 7.10.5.11.3 GPMC and NAND Flash — Asynchronous Mode
        12. 7.10.5.12 I2C
        13. 7.10.5.13 MCAN
        14. 7.10.5.14 MCASP
        15. 7.10.5.15 MCSPI
          1. 7.10.5.15.1 MCSPI — Controller Mode
          2. 7.10.5.15.2 MCSPI — Peripheral Mode
        16. 7.10.5.16 MMCSD
          1. 7.10.5.16.1 MMC0 - eMMC/SD/SDIO Interface
            1. 7.10.5.16.1.1  Legacy SDR Mode
            2. 7.10.5.16.1.2  High Speed SDR Mode
            3. 7.10.5.16.1.3  HS200 Mode
            4. 7.10.5.16.1.4  Default Speed Mode
            5. 7.10.5.16.1.5  High Speed Mode
            6. 7.10.5.16.1.6  UHS–I SDR12 Mode
            7. 7.10.5.16.1.7  UHS–I SDR25 Mode
            8. 7.10.5.16.1.8  UHS–I SDR50 Mode
            9. 7.10.5.16.1.9  UHS–I DDR50 Mode
            10. 7.10.5.16.1.10 UHS–I SDR104 Mode
          2. 7.10.5.16.2 MMC1/MMC2 - SD/SDIO Interface
            1. 7.10.5.16.2.1 Default Speed Mode
            2. 7.10.5.16.2.2 High Speed Mode
            3. 7.10.5.16.2.3 UHS–I SDR12 Mode
            4. 7.10.5.16.2.4 UHS–I SDR25 Mode
            5. 7.10.5.16.2.5 UHS–I SDR50 Mode
            6. 7.10.5.16.2.6 UHS–I DDR50 Mode
            7. 7.10.5.16.2.7 UHS–I SDR104 Mode
        17. 7.10.5.17 OSPI
          1. 7.10.5.17.1 OSPI0 PHY Mode
            1. 7.10.5.17.1.1 OSPI0 With PHY Data Training
            2. 7.10.5.17.1.2 OSPI0 Without Data Training
              1. 7.10.5.17.1.2.1 OSPI0 PHY SDR Timing
              2. 7.10.5.17.1.2.2 OSPI0 PHY DDR Timing
          2. 7.10.5.17.2 OSPI0 Tap Mode
            1. 7.10.5.17.2.1 OSPI0 Tap SDR Timing
            2. 7.10.5.17.2.2 OSPI0 Tap DDR Timing
        18. 7.10.5.18 Timers
        19. 7.10.5.19 UART
        20. 7.10.5.20 USB
  9. Detailed Description
    1. 8.1 Overview
    2. 8.2 Processor Subsystems
      1. 8.2.1 Arm Cortex-A53 Subsystem
      2. 8.2.2 Device/Power Manager
      3. 8.2.3 MCU Arm Cortex-R5F Subsystem
    3. 8.3 Accelerators and Coprocessors
      1. 8.3.1 C7xV-256 Deep Learning Accelerator
      2. 8.3.2 Vision Pre-processing Accelerator
      3. 8.3.3 JPEG Encoder
      4. 8.3.4 Video Accelerator
    4. 8.4 Other Subsystems
      1. 8.4.1 Dual Clock Comparator (DCC)
      2. 8.4.2 Data Movement Subsystem (DMSS)
      3. 8.4.3 Memory Cyclic Redundancy Check (MCRC)
      4. 8.4.4 Peripheral DMA Controller (PDMA)
      5. 8.4.5 Real-Time Clock (RTC)
    5. 8.5 Peripherals
      1. 8.5.1  Gigabit Ethernet Switch (CPSW3G)
      2. 8.5.2  Camera Serial Interface Receiver (CSI_RX_IF)
      3. 8.5.3  Display Subsystem (DSS)
      4. 8.5.4  Enhanced Capture (ECAP)
      5. 8.5.5  Error Location Module (ELM)
      6. 8.5.6  Enhanced Pulse Width Modulation (EPWM)
      7. 8.5.7  Error Signaling Module (ESM)
      8. 8.5.8  Enhanced Quadrature Encoder Pulse (EQEP)
      9. 8.5.9  General-Purpose Interface (GPIO)
      10. 8.5.10 General-Purpose Memory Controller (GPMC)
      11. 8.5.11 Global Timebase Counter (GTC)
      12. 8.5.12 Inter-Integrated Circuit (I2C)
      13. 8.5.13 Modular Controller Area Network (MCAN)
      14. 8.5.14 Multichannel Audio Serial Port (MCASP)
      15. 8.5.15 Multichannel Serial Peripheral Interface (MCSPI)
      16. 8.5.16 Multi-Media Card Secure Digital (MMCSD)
      17. 8.5.17 Octal Serial Peripheral Interface (OSPI)
      18. 8.5.18 Timers
      19. 8.5.19 Universal Asynchronous Receiver/Transmitter (UART)
      20. 8.5.20 Universal Serial Bus Subsystem (USBSS)
  10. Applications, Implementation, and Layout
    1. 9.1 Device Connection and Layout Fundamentals
      1. 9.1.1 Power Supply
        1. 9.1.1.1 Power Supply Designs
        2. 9.1.1.2 Power Distribution Network Implementation Guidance
      2. 9.1.2 External Oscillator
      3. 9.1.3 JTAG, EMU, and TRACE
      4. 9.1.4 Unused Pins
    2. 9.2 Peripheral- and Interface-Specific Design Information
      1. 9.2.1 DDR Board Design and Layout Guidelines
      2. 9.2.2 OSPI/QSPI/SPI Board Design and Layout Guidelines
        1. 9.2.2.1 No Loopback, Internal PHY Loopback, and Internal Pad Loopback
        2. 9.2.2.2 External Board Loopback
        3. 9.2.2.3 DQS (only available in Octal SPI devices)
      3. 9.2.3 USB VBUS Design Guidelines
      4. 9.2.4 System Power Supply Monitor Design Guidelines
      5. 9.2.5 High Speed Differential Signal Routing Guidance
      6. 9.2.6 Thermal Solution Guidance
    3. 9.3 Clock Routing Guidelines
      1. 9.3.1 Oscillator Routing
  11. 10Device and Documentation Support
    1. 10.1 Device Nomenclature
      1. 10.1.1 Standard Package Symbolization
      2. 10.1.2 Device Naming Convention
    2. 10.2 Tools and Software
    3. 10.3 Documentation Support
    4. 10.4 支持资源
    5. 10.5 Trademarks
    6. 10.6 静电放电警告
    7. 10.7 术语表
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Packaging Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • AMB|484
散热焊盘机械数据 (封装 | 引脚)
订购信息

System Power Supply Monitor Design Guidelines

The VMON_VSYS pin provides a way to monitor a system power supply. This system power supply is typically a single pre-regulated power source for the entire system and can be connected to the VMON_VSYS pin via and external resistor divider circuit. This system supply is monitored by comparing the external voltage divider output voltage to an internal voltage reference, where a power fail event is triggered when the voltage applied to VMON_VSYS drops below the internal reference voltage. The actual system power supply voltage trip point is determined by the system designer when selecting component values used to implement the external resistor voltage divider circuit.

When designing the resistor divider circuit the designer must understand various factors which contribute to variability in the system power supply monitor trip point. The first thing to consider is the initial accuracy of the VMON_VSYS input threshold which has a nominal value of 0.45 V, with a variation of ±3%. Precision 1% resistors with similar thermal coefficient are recommended for implementing the resistor voltage divider. This minimizes variability contributed by resistor value tolerances. Input leakage current associated with VMON_VSYS must also be considered since any current flowing into the pin creates a loading error on the voltage divider output. The VMON_VSYS input leakage current can be in the range of 10 nA to 2.5 µA when applying 0.45 V.

Note:

The resistor voltage divider shall be designed such that the output voltage never exceeds the maximum value defined in the Recommended Operating Conditions section, during normal operating conditions.

Figure 9-5 presents an example, where the system power supply is nominally 5 V and the maximum trigger threshold is 5 V - 10%, or 4.5 V.

For this example, the designer must understand which variables effect the maximum trigger threshold when selecting resistor values. A device which has a VMON_VSYS input threshold of 0.45 V + 3% needs to be considered when trying to design a voltage divider that doesn’t trip until the system supply drops 10%. The effect of resistor tolerance and input leakage also needs to be considered, but the contribution to the maximum trigger point is not obvious. When selecting component values which produce a maximum trigger voltage, the system designer must consider a condition where the value of R1 is 1% low and the value of R2 is 1% high combined with a condition where input leakage current for the VMON_VSYS pin is 2.5 µA. When implementing a resistor divider where R1 = 4.81 KΩ and R2 = 40.2 KΩ, the result is a maximum trigger threshold of 4.517 V.

Once component values have been selected to satisfy the maximum trigger voltage as described above, the system designer can determine the minimum trigger voltage by calculating the applied voltage that produces an output voltage of 0.45 V - 3% when the value of R1 is 1% high and the value of R2 is 1% low, and the input leakage current is 10 nA, or zero. Using an input leakage of zero with the resistor values given above, the result is a minimum trigger threshold of 4.013 V.

This example demonstrates a system power supply voltage trip point that ranges from 4.013 V to 4.517 V. Approximately 250 mV of this range is introduced by VMON_VSYS input threshold accuracy of ±3%, approximately 150 mV of this range is introduced by resistor tolerance of ±1%, and approximately 100 mV of this range is introduced by loading error when VMON_VSYS input leakage current is 2.5 µA.

The resistor values selected in this example produces approximately 100 µA of bias current through the resistor divider when the system supply is 4.5 V. The 100 mV of loading error mentioned above can be reduced to about 10 mV by increasing the bias current through the resistor divider to approximately 1 mA. So resistor divider bias current vs loading error is something the system designer needs to consider when selecting component values.

The system designer must also consider implementing a noise filter on the voltage divider output since VMON_VSYS has minimum hysteresis and a high-bandwidth response to transients. This can be done by installing a capacitor across R1 as shown in Figure 9-5. However, the system designer must determine the response time of this filter based on system supply noise and expected response to transient events.

GUID-04102B71-40CB-44F1-8A58-49A5ED8CD00E-low.gifFigure 9-5 System Supply Monitor Voltage Divider Circuit

VMON_1P8_SOC pin provides a way to monitor external 1.8 V power supplies. This pin must be connected directly to their respective power source. An internal resistor divider with software control is implemented inside the SoC for each of these pins. Software can program each internal resistor divider to create appropriate under voltage and over voltage interrupts.

VMON_3P3_SOC pin provides a way to monitor external 3.3 V power supplies. This pin must be connected directly to their respective power source. An internal resistor divider with software control is implemented inside the SoC for each of these pins. Software can program each internal resistor divider to create appropriate under voltage and over voltage interrupts.