ZHCSIP5 August   2018 PGA305

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     Device Images
      1.      PAG305 简化方框图
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics – Reverse Voltage Protection
    6. 6.6  Electrical Characteristics – Regulators
    7. 6.7  Electrical Characteristics – Internal Reference
    8. 6.8  Electrical Characteristics – Bridge Sensor Supply
    9. 6.9  Electrical Characteristics – Temperature Sensor Supply
    10. 6.10 Electrical Characteristics – Internal Temperature Sensor
    11. 6.11 Electrical Characteristics – P Gain (Chopper Stabilized)
    12. 6.12 Electrical Characteristics – P Analog-to-Digital Converter
    13. 6.13 Electrical Characteristics – T Gain (Chopper Stabilized)
    14. 6.14 Electrical Characteristics – T Analog-to-Digital Converter
    15. 6.15 Electrical Characteristics – One-Wire Interface
    16. 6.16 I2C Interface
    17. 6.17 Electrical Characteristics – DAC Output
    18. 6.18 Electrical Characteristics – DAC Gain
    19. 6.19 Electrical Characteristics – Non-Volatile Memory
    20. 6.20 Electrical Characteristics – Diagnostics
    21. 6.21 Operating Characteristics
    22. 6.22 I2C Interface Timing Requirements
    23. 6.23 Timing Diagram
    24. 6.24 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Reverse-Voltage Protection Block
      2. 7.3.2  Linear Regulators
      3. 7.3.3  Internal Reference
        1. 7.3.3.1 High-Voltage Reference
        2. 7.3.3.2 Accurate Reference
      4. 7.3.4  BRG+ to BRG– Supply for the Resistive Bridge
      5. 7.3.5  ITEMP Supply for the Temperature Sensor
      6. 7.3.6  Internal Temperature Sensor
      7. 7.3.7  P Gain
      8. 7.3.8  P Analog-to-Digital Converter
        1. 7.3.8.1 P Sigma-Delta Modulator for P ADC
        2. 7.3.8.2 P Decimation Filter for P ADC
      9. 7.3.9  T Gain
      10. 7.3.10 T Analog-to-Digital Converter
        1. 7.3.10.1 T Sigma-Delta Modulator for T ADC
        2. 7.3.10.2 T Decimation Filters for T ADC
      11. 7.3.11 P GAIN and T GAIN Calibration
      12. 7.3.12 One-Wire Interface (OWI)
        1. 7.3.12.1 Overview of OWI
        2. 7.3.12.2 Activating and Deactivating the OWI Interface
          1. 7.3.12.2.1 Activating OWI Communication
          2. 7.3.12.2.2 Deactivating OWI Communication
        3. 7.3.12.3 OWI Protocol
          1. 7.3.12.3.1 OWI Frame Structure
            1. 7.3.12.3.1.1 Standard Field Structure
            2. 7.3.12.3.1.2 Frame Structure
            3. 7.3.12.3.1.3 Sync Field
            4. 7.3.12.3.1.4 Command Field
            5. 7.3.12.3.1.5 Data Fields
          2. 7.3.12.3.2 OWI Commands
            1. 7.3.12.3.2.1 OWI Write Command
            2. 7.3.12.3.2.2 OWI Read Initialization Command
            3. 7.3.12.3.2.3 OWI Read-Response Command
            4. 7.3.12.3.2.4 OWI Burst-Write Command (EEPROM Cache Access)
            5. 7.3.12.3.2.5 OWI Burst Read Command (EEPROM Cache Access)
          3. 7.3.12.3.3 OWI Operations
            1. 7.3.12.3.3.1 Write Operation
            2. 7.3.12.3.3.2 Read Operation
            3. 7.3.12.3.3.3 EEPROM Burst Write
            4. 7.3.12.3.3.4 EEPROM Burst Read
        4. 7.3.12.4 OWI Communication-Error Status
      13. 7.3.13 I2C Interface
        1. 7.3.13.1 Overview of I2C Interface
        2. 7.3.13.2 Clocking Details of I2C Interface
        3. 7.3.13.3 I2C Interface Protocol
        4. 7.3.13.4 PGA305 I2C Runtime Commands
        5. 7.3.13.5 PGA305 I2C Transfer Example
      14. 7.3.14 DAC Output
        1. 7.3.14.1 Ratiometric vs Absolute
      15. 7.3.15 DAC Gain
      16. 7.3.16 Memory
        1. 7.3.16.1 EEPROM Memory
          1. 7.3.16.1.1 EEPROM Cache
          2. 7.3.16.1.2 EEPROM Programming Procedure
          3. 7.3.16.1.3 EEPROM Programming Current
          4. 7.3.16.1.4 CRC
        2. 7.3.16.2 Control and Status Registers Memory
      17. 7.3.17 Diagnostics
        1. 7.3.17.1 Power Supply Diagnostics
        2. 7.3.17.2 Signal Chain Faults
          1. 7.3.17.2.1 P Gain and T Gain Input Faults
          2. 7.3.17.2.2 P Gain and T Gain Output Diagnostics
          3. 7.3.17.2.3 Masking Signal Chain Faults
          4. 7.3.17.2.4 Fault Detection Timing
      18. 7.3.18 Reading Diagnostics Information Through I2C
      19. 7.3.19 Digital Compensation and Filter
        1. 7.3.19.1 Digital Gain and Offset
        2. 7.3.19.2 TC and NL Correction
          1. 7.3.19.2.1 TC and NL Coefficients
            1. 7.3.19.2.1.1 No TC and NL Coefficients
          2. 7.3.19.2.2 TC Compensation Using the Internal Temperature Sensor
        3. 7.3.19.3 Clamping
        4. 7.3.19.4 Filter
      20. 7.3.20 Filter Coefficients
        1. 7.3.20.1 No Filtering
        2. 7.3.20.2 Filter Coefficients for P ADC Sampling Rate = 1024 µs
    4. 7.4 Device Functional Modes
      1. 7.4.1 Voltage Mode
      2. 7.4.2 Current Mode
    5. 7.5 Register Maps
      1. 7.5.1 Register Settings
      2. 7.5.2 Control and Status Registers
        1. 7.5.2.1  Digital Interface Control (M0 Address = 0x40000506) (DI Page Address = 0x2) (DI Page Offset = 0x06)
        2. 7.5.2.2  DAC_CTRL_STATUS (M0 Address: 0x40000538) (DI Page Address: 0x2) (DI Page Offset: 0x38)
        3. 7.5.2.3  DAC_CONFIG (EEPROM Address = 0x40000032) (DI Page Address: 0x2) (DI Page Offset: 0x39)
        4. 7.5.2.4  OP_STAGE_CTRL (EEPROM Address = 0x40000033) (DI Page Address: 0x2) (DI Page Offset: 0x3B)
        5. 7.5.2.5  BRDG_CTRL (EEPROM Address = 0x40000034) (DI Page Address: 0x2) (DI Page Offset: 0x46)
        6. 7.5.2.6  P_GAIN_SELECT (EEPROM Address = 0x40000035) (DI Page Address: 0x2) (DI Page Offset: 0x47)
        7. 7.5.2.7  T_GAIN_SELECT (EEPROM Address = 0x40000036) (DI Page Address: 0x2) (DI Page Offset: 0x48)
        8. 7.5.2.8  TEMP_CTRL (EEPROM Address = 0x40000037) (DI Page Address: 0x2) (DI Page Offset: 0x4C)
        9. 7.5.2.9  TEMP_SE (EEPROM Address = 0x4000003A)
        10. 7.5.2.10 DIAG_ENABLE (EEPROM Address = 0x40000056)
        11. 7.5.2.11 EEPROM_LOCK (EEPROM Address = 0x40000057)
        12. 7.5.2.12 AFEDIAG_CFG (EEPROM Address = 0x40000058)
        13. 7.5.2.13 AFEDIAG_MASK (EEPROM Address = 0x40000059)
        14. 7.5.2.14 ADC_24BIT_ENABLE (EEPROM Address = 0x40000068)
        15. 7.5.2.15 OFFSET_ENABLE (EEPROM Address = 0x40000069)
        16. 7.5.2.16 COMPENSATION_CONTROL (EEPROM Address = N/A) (DI Page Address: 0x0) (DI Page Offset: 0x0C)
        17. 7.5.2.17 EEPROM_PAGE_ADDRESS (EEPROM Address = N/A) (DI Page Address: 0x5) (DI Page Offset: 0x88)
        18. 7.5.2.18 EEPROM_CTRL (EEPROM Address = N/A) (DI Page Address: 0x5) (DI Page Offset: 0x89)
        19. 7.5.2.19 EEPROM_CRC (EEPROM Address = N/A) (DI Page Address: 0x5) (DI Page Offset: 0x8A)
        20. 7.5.2.20 EEPROM_STATUS (EEPROM Address = N/A) (DI Page Address: 0x5) (DI Page Offset: 0x8B)
        21. 7.5.2.21 EEPROM_CRC_STATUS (EEPROM Address = N/A) (DI Page Address: 0x5) (DI Page Offset: 0x8C)
        22. 7.5.2.22 EEPROM_CRC_VALUE (EEPROM Address = 0x4000007F) (DI Page Address: 0x5) (DI Page Offset: 0x8D)
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 4-mA to 20-mA Output With Internal Sense Resistor
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Calibration Tips
            1. 8.2.1.2.1.1 Programming the EEPROM for 4-mA to 20-mA Output
        3. 8.2.1.3 Application Curve
      2. 8.2.2 0- to 10-V Absolute Output With Internal Drive
        1. 8.2.2.1 Design Requirements
      3. 8.2.3 0- to 5-V Ratiometric Output With Internal Drive
        1. 8.2.3.1 Design Requirements
        2. 8.2.3.2 Detailed Design Procedure
          1. 8.2.3.2.1 Programmer Tips
            1. 8.2.3.2.1.1 Resetting the Microprocessor and Enable Digital Interface
            2. 8.2.3.2.1.2 Turning On the Accurate Reference Buffer (REFCAP Voltage)
            3. 8.2.3.2.1.3 Turning On DAC and DAC GAIN
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11器件和文档支持
    1. 11.1 接收文档更新通知
    2. 11.2 社区资源
    3. 11.3 商标
    4. 11.4 静电放电警告
    5. 11.5 术语表
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.5.1 Register Settings

Before the PAG305 device can be used in any application, the device must be configured by setting various control registers to the desired values. Table 19 lists all the registers that must be configured and their respective default configurations. Note that the registers are configured by writing to the appropriate EEPROM addresses listed in the Control and Status Registers section.

Table 19. Default Register Settings

REGISTER VALUE (HEX) DESCRIPTION
DIG_IF_CTRL 0x62 I2C Interface Enabled in Fast Mode (400kHz - 800kHz)
DAC_CONFIG 0x00 DAC is set for absolute voltage output.
OP_STAGE_CTRL 0x02 Output is configured for 0V - 5V absolute Voltage Output (DAC Gain 4V/V).
BRG_CTRL 0x01 Bridge excitation is set to 2.5 V.
P_GAIN_SELECT 0x80 P_GAIN is set to 5 V/V gain with Signal Inversion.
T_GAIN_SELECT 0x00 T_GAIN is set for 1.33 V/V gain without Signal Inversion.
TEMP_CTRL 0x40 ITEMP drive is disabled and T signal chain is set for VINT+ – VINT–.
TEMP_SE 0x00 T GAIN is in single-ended configuration.
NORMAL_LOW_LSB 0x67 DAC normal low output set to 0x0667. Must be updated during calibration
NORMAL_LOW_MSB 0x06 DAC normal low output set to 0x0667. Must be updated during calibration
NORMAL_HIGH_LSB 0x9A DAC normal high output set to 0x399A. Must be updated during calibration
NORMAL_HIGH_MSB 0x39 DAC normal high output set to 0x399A. Must be updated during calibration
LOW_CLAMP_LSB 0x34 DAC clamp low output set to 0x0334. Must be updated during calibration
LOW_CLAMP_MSB 0x03 DAC clamp low output set to 0x0334. Must be updated during calibration
HIGH_CLAMP_LSB 0xCF DAC clamp high output set to 0x3CCF. Must be updated during calibration
HIGH_CLAMP_MSB 0x3C DAC clamp high output set to 0x3CCF. Must be updated during calibration
DIAG_ENABLE 0x00 Application Diagnostics are Disabled (The device will not Reset on WatchDog Error or EEPROM CRC Error)
EEPROM_LOCK 0x00 EEPROM is unlocked.
AFEDIAG_CFG 0x07 Diagnostics pulldown (1 MΩ) and pullup (1 MΩ) resistors enabled, VINP_UV threshold = 10% and VINP_OV threshold = 70%
DIAG_ENABLE 0x00 Diagnostics are disabled.
AFEDIAG_MASK 0x21 VINP_OV and PGAIN_UV detection enabled
SERIAL_NUMBER_BYTE0-1-2-3 0x00000000 Serial number specified by customer