ZHCSEW6G may   2013  – november 2020 DS90UB913A-Q1

PRODUCTION DATA  

  1.   1
  2. 1特性
  3. 2应用
  4. 3说明
  5. 4Revision History
  6.   Device Comparison Table
  7. 5Pin Configuration and Functions
    1.     Pin Functions: DS90UB913A-Q1 Serializer
  8. 6Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Recommended Serializer Timing For PCLK
    7. 6.7  AC Timing Specifications (SCL, SDA) - I2C-Compatible
    8. 6.8  Bidirectional Control Bus DC Timing Specifications (SCL, SDA) - I2C-Compatible
    9. 6.9  Timing Diagrams
    10. 6.10 Serializer Switching Characteristics
    11. 6.11 Typical Characteristics
  9. 7Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Serial Frame Format
      2. 7.3.2 Line Rate Calculations for the DS90UB913A/914A
      3. 7.3.3 Error Detection
      4. 7.3.4 Synchronizing Multiple Cameras
      5. 7.3.5 General Purpose I/O (GPIO) Descriptions
      6. 7.3.6 LVCMOS VDDIO Option
      7. 7.3.7 Pixel Clock Edge Select (TRFB / RRFB)
      8. 7.3.8 Power Down
    4. 7.4 Device Functional Modes
      1. 7.4.1 DS90UB913A/914A Operation with External Oscillator as Reference Clock
      2. 7.4.2 DS90UB913A/914A Operation with Pixel Clock from Imager as Reference Clock
      3. 7.4.3 MODE Pin on Serializer
      4. 7.4.4 Internal Oscillator
      5. 7.4.5 Built In Self Test
      6. 7.4.6 BIST Configuration and Status
      7. 7.4.7 Sample BIST Sequence
    5. 7.5 Programming
      1. 7.5.1 Programmable Controller
      2. 7.5.2 Description of Bidirectional Control Bus and I2C Modes
      3. 7.5.3 I2C Pass-Through
      4. 7.5.4 Slave Clock Stretching
      5. 7.5.5 ID[x] Address Decoder on the Serializer
      6. 7.5.6 Multiple Device Addressing
    6. 7.6 Register Maps
  10.   Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Power Over Coax
      2. 8.1.2 Power-Up Requirements and PDB Pin
      3. 8.1.3 AC Coupling
      4. 8.1.4 Transmission Media
    2. 8.2 Typical Applications
      1. 8.2.1 Coax Application
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
      2. 8.2.2 STP Application
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
        3. 8.2.2.3 Application Curves
  11.   Power Supply Recommendations
  12. 8Layout
    1. 8.1 Layout Guidelines
      1. 8.1.1 Interconnect Guidelines
    2. 8.2 Layout Example
  13. 9Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
  14.   Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MINNOMMAXUNIT
Supply Voltage (VDD_n)1.711.81.89V
LVCMOS Supply VoltageVDDIO= 1.8 V1.711.81.89V
VDDIO= 3.3 V33.33.6
VDDIO= 2.8 V2.522.83.08
Supply Noise(1)VDD_n = 1.8 V25mVp-p
VDDIO = 1.8 V25
VDDIO = 3.3 V50
Power-Over-Coax Supply Noiseƒ = 30 Hz - 1 KHz, trise > 100 µs
Measured differentially between DOUT+ and DOUT– (coax mode only)		10mVp-p
ƒ = 1 KHz - 50 MHz
Measured differentially between DOUT+ and DOUT- (coax mode only)		10mVp-p
Operating Free Air Temperature (TA)–4025105°C
PCLK Clock Frequency10-bit mode50100MHz
12-bit HF mode37.575MHz
12-bit LF mode2550MHz
External Clock Input Frequency to GPO310-bit mode2550MHz
12-bit HF mode2550MHz
12-bit LF mode2550MHz
(1) Supply noise testing was done with minimum capacitors (as shown on Figure 8-9, Figure 8-5 on the PCB. A sinusoidal signal is AC coupled to the VDD_n (1.8 V) supply with amplitude = 25 mVp-p measured at the device VDD_n pins. Bit error rate testing of input to the Ser and output of the Des with 10-meter cable shows no error when the noise frequency on the Ser is less than 1 MHz. The Des on the other hand shows no error when the noise frequency is less than 750 kHz.