ZHCSPB0 april   2023 LM5171-Q1

ADVANCE INFORMATION  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Bias Supplies and Voltage Reference (VCC, VDD, and VREF)
      2. 7.3.2  Undervoltage Lockout (UVLO) and Controller Enable or Disable
      3. 7.3.3  High Voltage Inputs (HV1, HV2)
      4. 7.3.4  Current Sense Amplifier
      5. 7.3.5  Control Commands
        1. 7.3.5.1 Channel Enable Commands (EN1, EN2)
        2. 7.3.5.2 Direction Command (DIR1 and DIR2)
        3. 7.3.5.3 Channel Current Setting Commands (ISET1 and ISET2)
      6. 7.3.6  Channel Current Monitor (IMON1, IMON2)
        1. 7.3.6.1 Individual Channel Current Monitor
        2. 7.3.6.2 Multiphase Total Current Monitoring
      7. 7.3.7  Cycle-by-Cycle Peak Current Limit (IPK)
      8. 7.3.8  Inner Current Loop Error Amplifier
      9. 7.3.9  Outer Voltage Loop Error Amplifier
      10. 7.3.10 Soft Start, Diode Emulation, and Forced PWM Control (SS/DEM1 and SS/DEM2)
        1. 7.3.10.1 Soft-Start Control by the SS/DEM Pins
        2. 7.3.10.2 DEM Programming
        3. 7.3.10.3 FPWM Programming and Dynamic FPWM and DEM Change
        4. 7.3.10.4 SS Pin as the Restart Timer
      11. 7.3.11 Gate Drive Outputs, Dead Time Programming and Adaptive Dead Time (HO1, HO2, LO1, LO2, DT/SD)
      12. 7.3.12 Emergent Latched Shutdown (DT/SD)
      13. 7.3.13 PWM Comparator
      14. 7.3.14 Oscillator (OSC)
      15. 7.3.15 Synchronization to an External Clock (SYNCI, SYNCO)
      16. 7.3.16 Overvoltage Protection (OVP)
      17. 7.3.17 Multiphase Configurations (SYNCO, OPT)
        1. 7.3.17.1 Multiphase in Star Configuration
        2. 7.3.17.2 Daisy-Chain Configurations for 2, 3, or 4 Phases parallel operations
        3. 7.3.17.3 Daisy-Chain configuration for 6 or 8 phases parallel operation
      18. 7.3.18 Thermal Shutdown
    4. 7.4 Programming
      1. 7.4.1 Dynamic Dead Time Adjustment
      2. 7.4.2 UVLO Programming
    5. 7.5 I2C Serial Interface
      1. 7.5.1 REGFIELD Registers
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Small Signal Model
        1. 8.1.1.1 Current Loop Small Signal Model
        2. 8.1.1.2 Current Loop Compensation
        3. 8.1.1.3 Voltage Loop Small Signal Model
        4. 8.1.1.4 Voltage Loop Compensation
    2. 8.2 Typical Application
      1. 8.2.1 60-A, Dual-Phase, 48-V to 12-V Bidirectional Converter
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1  Determining the Duty Cycle
          2. 8.2.1.2.2  Oscillator Programming
          3. 8.2.1.2.3  Power Inductor, RMS and Peak Currents
          4. 8.2.1.2.4  Current Sense (RCS)
          5. 8.2.1.2.5  Current Setting Limits (ISETx)
          6. 8.2.1.2.6  Peak Current Limit
          7. 8.2.1.2.7  Power MOSFETS
          8. 8.2.1.2.8  Bias Supply
          9. 8.2.1.2.9  Boot Strap
          10. 8.2.1.2.10 OVP
          11. 8.2.1.2.11 Dead Time
          12. 8.2.1.2.12 Channel Current Monitor (IMONx)
          13. 8.2.1.2.13 UVLO Pin Usage
          14. 8.2.1.2.14 HVx Pin Configuration
          15. 8.2.1.2.15 Loop Compensation
          16. 8.2.1.2.16 Soft Start
          17. 8.2.1.2.17 PWM to ISET Pins
        3. 8.2.1.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Examples
  9. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
    2. 9.2 接收文档更新通知
    3. 9.3 支持资源
    4. 9.4 Trademarks
    5. 9.5 静电放电警告
    6. 9.6 术语表
  10. 10Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.5 Electrical Characteristics

Typical values correspond to TJ = 25°C. Minimum and maximum limits apply over TJ = –40°C to 150°C. Unless otherwise stated, FOSC = 100 kHz; VVCC = 10 V; VHV1 = VHV2 = VHV-Port = 48V and VLV-Port = 12 V.
SYMBOL PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
HV Port (HV1, HV2)
ISHUTDOWN1 HV1 pin current in shutdown mode VUVLO = 0 V 10 µA
ISHUTDOWN2 HV2 pin current in shutdown mode VUVLO = 0 V 10 µA
IOPERATING HV1 and HV2 pin current in operating VUVLO > 2.6 V, VVCC > 9 V 1 mA
VCC Bias Supply (VCC)
VVCC_reg VCC LDO regulation setting point VHV1 > 10V 8.55 9 9.45 V
VCCUVLO VCC under voltage detection VCC falling 7.7 8 8.2 V
VCCHYS VCC UVLO hysteresis VCC rising 8.2 8.5 8.7 V
IVCC_SD VCC sink current in shutdown mode VUVLO = 0 V, VVCC=10 V 20 µA
IVCC_SB VCC sink current in standby: no switching VUVLO > 2.6 V, VVCC > 9 V, EN1=EN2=0 V 10 mA
VDD Analog Bias Supply (VDD)
VVDD VDD voltage VUVLO > 2.6 V, VVCC > 9 V 4.75 5 5.25 V
VDDUV VDD undervoltage detection VDD falling 4.25 4.5 4.75 V
VDDHYS VDD UVLO hysteresis VDD rising above VDDUV 0.1 0.2 0.3 V
IVDD VDD source current limit VVDD = 4.6 V 10 mA
VOLTAGE REFERENCE (VREF)
VREF Voltage reference VUVLO > 2.6 V, VVCC > 9 V, VVDD > VDDUV 3.465 3.500 3.535 V
IVREF VREF source current limit VVREF = 3.5V 2 mA
Master ON/OFF Control (UVLO)
VUVLO_TH UVLO release threshold UVLO voltage rising 2.4 2.5 2.6 V
IHYS UVLO hysteresis current UVLO source current when VUVLO > 2.6 V 21 25 29 µA
VRES UVLO shutdown and IC reset voltage threshold UVLO voltage falling 1 1.25 1.5 V
UVLO shutdown release  UVLO voltage rising above VRES 0.15 0.25 0.35 V
tUVLO UVLO 2.5V threshold glitch filter UVLO voltage both rising and falling 2.5 µs
tVRES UVLO 1.25V VRES threshold glitch filter  5 10 µs
UVLO internal pull-down current 100 nA
Enable Inputs EN1 and EN2
VIL Enable input low state The driver outputs disabled 1.0 V
VIH Enable input high state The driver outputs enabled 2.0 V
Internal pulldown impedance EN1, EN2 logic inputs internal pulldown resistor 1 MegΩ
EN glitch filter time (the rising and falling edges) 2.5 µs
DIRECTION COMMANDS (DIR1, DIR2)
VDIR1, VDIR2 Command for current flowing from LV-Port to HV-Port (boost mode 12 V to 48 V), for CH-1 and CH-2, respectively Actively pulled low by external circuit 1 V
VDIR1, VDIR2 Command for current flowing from HV-Port to LV-Port (buck mode 48 V to 12 V), for CH-1 and CH-2, respectively Actively pulled high by external circuit 2 V
VDIR1, VDIR2 Standby (invalid DIR command) DIR pin (DIR1 or DIR2) neither active High nor active Low 1.5 V
DIR glitch filter (the rising and falling edges) Both Rising and Falling Edges 10 µs
ISET INPUTS (ISET1, ISET2)
ISET internal dc offset voltage 0.99 1.0 1.01 V
GISET Gain of the regulated inductor DC current sense voltage to ISET voltage |VCSA – VCSB| = 50 mV 24.75 25 25.25 mV/V
ISET internal pull-down current sink 75 200 nA
Output Current Monitor (IMON1, IMON2)
Gain of IMON1 and IMON2 current source versus channel current sense voltage |CSA-CSB| = 50 mV,  CONFIG = 'Inductor current monitor", VDIR > 2V 1.98 2 2.02 µA/mV
Gain of IMON1 and IMON2 current source versus channel current sense voltage |CSA-CSB| = 50 mV,  CONFIG = 'Inductor current monitor",  VDIR < 1 V 1.98 2 2.02 uA/mV
Gain of IMON1 and IMON2 current source versus channel current sense voltage |CSA-CSB| = 50 mV,  CONFIG = 'Output current monitor", VDIR < 1 V, Duty cycle = 0.75 0.475 0.5 0.525 uA/mV
Gain of IMON1 and IMON2 current source versus channel current sense voltage |CSA-CSB| = 10 mV,  CONFIG = 'Inductor current monitor", VDIR > 2V 1.98 2 2.02 uA/mV
Gain of IMON1 and IMON2 current source versus channel current sense voltage |CSA-CSB| = 10 mV,  CONFIG = 'Inductor current monitor",  VDIR < 1 V 1.98 2 2.02 uA/mV
Gain of IMON1 and IMON2 current source versus channel current sense voltage |CSA-CSB| = 10 mV,  CONFIG = 'Output current monitor", VDIR < 1 V, Duty cycle = 0.75 0.475 0.5 0.525 uA/mV
IMON1 and IMON2 DC offset current |CSA-CSB| = 0mV 47.5 50 52.5 µA
CURRENT SENSE AMPLIFIER (BOTH CHANNELS)
GCS_BK1 Gain of amplifier output to current sense voltage in buck mode |VCSA – VCSB| = 50 mV, VDIR > 2 V 39.6 40 40.4 V/V
GCS_BST1 Gain of  amplifier output to current sense voltage in boost mode |VCSA – VCSB| = 50 mV, VDIR < 1 V 39.6 40 40.4 V/V
GCS_BK2 Gain of amplifier output to current sense voltage in buck mode |VCSA – VCSB| = 10 mV, VDIR > 2 V 39.2 40 40.8 V/V
GCS_BST2 Gain of amplifier output to current sense voltage in boost mode |VCSA – VCSB| = 10 mV, VDIR < 1 V 39.2 40 40.8 V/V
BW_cs Amplifier Bandwidth 10 MHz
TRANSCONDUCTION AMPLIFIER (COMP1, COMP2)
Gm Transconductance 100 µA/V
ICOMP Output source current limit VISET = 4 V, |VCSA – VCSB| = 0 mV 250 µA
Output sink current limit VISET = 0 V, VCSA – VCSB = 50 mV in the buck mode, or VCSA – VCSB = -50 mV in the boost mode -250 µA
BWgm Amplifier Bandwidth 10 MHz
VOLTAGE LOOP ERROR AMPLIFIERS (VSET, LVFB, LVERR, HVFB, HVERR)
AOL Open loop gain VVCC > 9 V, VVDD > VDDUV 80 dB
FBW Unity gain bandwidth 2 MHz
VOS Input offset voltage 1 mV
VERR_MIN Minimum amplifier output voltage Sourcing 2 mA 4 V
VERR_MAX Maximum amplifier output voltage Sinking 2 mA 0.5 V
PWM Comparator
COMP to output delay 50 ns
COMP to PWM comparator offset 1 V
TOFF_MIN Minimum off time 100 150 ns
PEAK CURRENT LIMIT (IPK)
GIPK_BK1 Gain from current sense voltage to cycle-by-cycle limit threshold voltage given at IPK pin, in buck mode VIPK = 3 V, VDIR >2 V 45 50 55 mV/V
GIPK_BK2 Gain from current sense voltage to cycle-by-cycle limit threshold voltage given at IPK pin, in buck mode VIPK = 1 V, VDIR >2 V 45 50 55 mV/V
GIPK_BST1 Gain from current sense voltage to cycle-by-cycle limit threshold voltage given at IPK pin, in boost mode VIPK = 3 V, VDIR <1 V 45 50 55 mV/V
GIPK_BST2 Gain from current sense voltage to cycle-by-cycle limit threshold voltage given at IPK pin, in boost mode VIPK = 1 V, VDIR <1 V 45 50 55 mV/V
OVER VOLTAGE PROTECTION (OVP)
OVP threshold 0.99 1 1.01 V
OVPHYS OVP Hysteresis 100 mV
tOVP OVP Glitch Filter 5 us
OSCILLATOR (OSC)
FOSC Oscillator frequency 1 ROSC = 41.5 kΩ, no external clock signal at SYNCI pin 90 100 110 kHz
Oscillator frequency 2 ROSC = 4.15 kΩ,  no external clock signal at SYNCI pin 900 1000 1100 kHz
VOSC OSC pin DC voltage OSC DC Level 1 V
SYNCHRONIZATION CLOCK INPUT (SYNCI)
VSYNIH SYNCI input threshold for high state 2 V
VSYNIL SYNCI input threshold for low state 1 V
Delay to establish synchronization 0.8 x FOSC < FSYNCI < 1.2 x Fosc 200 us
Internal pull-down impedance VSYNCI = 2.5 V 1000 kΩ
SYNCHRONIZATION CLOCK OUTPUT (SYNCO)
VSYNOH SYNCO high state 2.5 V
VSYNOL SYNCO low state 0.4 V
Sourcing current when SYNCO in high state VSYNCO = 2.5 V 1 mA
Sinking current when SYNCO in low state VSYNCO = 0.5 V 1 mA
SYNCO pulse width 80 100 120 ns
SYNCO pulse delay for multiphase daisy chain connection VOPT > 2 V, RSYNCO > 61.9 kΩ 90 Degree
VOPT < 1 V, RSYNCO > 61.9 kΩ 120 Degree
BOOTSTRAP (HB1, HB2)
VHB-UV Bootstrap undervoltage threshold (VHB – VSW) voltage rising 6 6.5 7 V
VHB-UV-HYS Bootstrap undervoltage hysteresis 0.5 V
IHB_LK Bootstrap quiescent current VHB – VSW = 10V, VHO – VSW = 0V 100 µA
HIGH SIDE GATE DRIVERS (HO1, HO2)
VOLH HO low-state output voltage IHO = 100 mA 0.1 V
VOHH HO high-state output voltage IHO = -100 mA, VOHH = VHB - VHO 0.15 V
HO rise time (10% to 90% pulse magnitude) CLD = 1000 pF 5 ns
HO fall time (90% to 10% pulse magnitude CLD = 1000 pF 4 ns
IOHH HO peak source current VHB – VSW = 10 V 4 A
IOLH HO peak sink current VHB – VSW = 10 V 5 A
LOW SIDE GATE DRIVERS (LO1, LO2)
VOLL LO low-state output voltage ILO = 100 mA 0.1 V
VOHL LO high-state output voltage ILO = -100 mA, VOHL = VVCC - VLO 0.15 V
LO rise time (10% to 90% pulse magnitude) CLD = 1000 pF 5 ns
LO fall time (90% to 10% pulse magnitude) CLD = 1000 pF 4 ns
IOHL LO peak source current VVCC = 10 V 4 A
IOLL LO peak sink current VVCC = 10 V 5 A
INTERLEAVE PHASE DELAY FROM CH-2 To CH-1 (OPT)
VOPTL OPT Input Low State OPT="0" 1.0 V
VOPTH OPT Input High State OPT="1" 2.0 V
HO2rising -HO1rising in the buck mode, or LO2rising -LO1rising in the boost mode OPT = "0" for 3 Phases in Daisy Chain Interleaving Operation 240 Degree
HO2rising -HO1rising in the buck mode, or LO2rising -LO1rising in the boost mode OPT= "1" for 1, 2, or 4 phases in Daisy Chain Interleaving Operation 180 Degree
Internal Pull down impedance 1 MegΩ
DEAD TIME and LATCHED SHUTDOWN (DT/SD)
tDT LO falling edge to HO rising edge delay RDT = 19.1 kΩ 50 ns
HO falling edge to LO rising edge delay RDT = 19.1 kΩ 50 ns
VDT DC voltage level for dead time programming 1.2 V
DC voltage level for adaptive dead time programming 3.1 V
VADPT HO-SW or LO-GND voltage threshold to enable cross output for adaptive dead time scheme VVCC > 9 V, (VHB – VSW) > 8 V, HO or LO voltage falling 1.5 V
tADPT LO falling edge to HO rising edge delay VDT = VVDD 40 ns
HO falling edge to LO rising edge delay VDT = VVDD 40 ns
tSD Latched shutdown glitch filter 1.875 2.5 3.125 µs
RSD Shutdown latch pulldown resistance Resistor in series with an external pull-down NFET 2 kΩ
SOFT START and FORCED PWM and DIODE EMULATION PRGRAMMING (SS/DEM1, SS/DEM2)
ISS SS charging current source during startup VSS  ≤ 3.3V,  VEN > 2 V, VUVLO > 2.5 V, DIR < 1 or DIR > 2 70 µA
ISS SS charging current source after startup VSS  ≥ 3.9V,  VEN > 2 V, VUVLO > 2.5 V, DIR < 1 or DIR > 2 50 µA
SS to gm input offset 1 V
RSS SS discharge device Rds(ON) VSS = 2 V 20 Ω
VSS_LOW SS discharge completion threshold Once it is discharged by internal logic 0.3 V
CONFIGURATIONS (CFG)
RCFG1 I2C Address: bXXXX000. IMON = Inductor Current 0 kΩ
RCFG2 I2C Address: bXXXX001. IMON = Inductor Current 0.316 0.324 kΩ
RCFG3 I2C Address: bXXXX010. IMON = Inductor Current 0.649 0.665 kΩ
RCFG4 I2C Address: bXXXX011. IMON = Inductor Current 1.1 1.13 kΩ
RCFG5 I2C Address: bXXXX100. IMON = Inductor Current 1.65 1.69 kΩ
RCFG6 I2C Address: bXXXX101. IMON = Inductor Current 2.43 2.49 kΩ
RCFG7 I2C Address: bXXXX110. IMON = Inductor Current 3.32 3.32,
3.4		 3.4 kΩ
RCFG8 I2C Address: bXXXX111. IMON = Inductor Current 4.53 4.64 kΩ
RCFG9 I2C Address: bXXXX111. IMON = Output Current 6.65 6.81 kΩ
RCFG10 I2C Address: bXXXX110. IMON = Output Current 10.2 10.5 kΩ
RCFG11 I2C Address: bXXXX101. IMON = Output Current 13.7 14.0 kΩ
RCFG12 I2C Address: bXXXX100. IMON = Output Current 18.7 19.1 kΩ
RCFG13 I2C Address: bXXXX011. IMON = Output Current 26.1 26.7 kΩ
RCFG14 I2C Address: bXXXX010. IMON = Output Current 37.4 38.3 kΩ
RCFG15 I2C Address: bXXXX001. IMON = Output Current 60.4 61.9 kΩ
RCFG16 I2C Address: bXXXX000. IMON = Output Current 95.3 97.6 kΩ
I2C INTERFACE (SLC, SDA)
VSDAL SDA input low state 1.0 V
VSDAH SDA input high state 2.0 V
VSCLL SCL input low state 1.0 V
VSCLH SCL input high state 2.0 V
Thermal Shutdown
TJ_SD Thermal shutdown 155 175 ℃
Thermal shutdown hysteresis 15 ℃