ZHCSPB0 april   2023 LM5171-Q1

ADVANCE INFORMATION  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Bias Supplies and Voltage Reference (VCC, VDD, and VREF)
      2. 7.3.2  Undervoltage Lockout (UVLO) and Controller Enable or Disable
      3. 7.3.3  High Voltage Inputs (HV1, HV2)
      4. 7.3.4  Current Sense Amplifier
      5. 7.3.5  Control Commands
        1. 7.3.5.1 Channel Enable Commands (EN1, EN2)
        2. 7.3.5.2 Direction Command (DIR1 and DIR2)
        3. 7.3.5.3 Channel Current Setting Commands (ISET1 and ISET2)
      6. 7.3.6  Channel Current Monitor (IMON1, IMON2)
        1. 7.3.6.1 Individual Channel Current Monitor
        2. 7.3.6.2 Multiphase Total Current Monitoring
      7. 7.3.7  Cycle-by-Cycle Peak Current Limit (IPK)
      8. 7.3.8  Inner Current Loop Error Amplifier
      9. 7.3.9  Outer Voltage Loop Error Amplifier
      10. 7.3.10 Soft Start, Diode Emulation, and Forced PWM Control (SS/DEM1 and SS/DEM2)
        1. 7.3.10.1 Soft-Start Control by the SS/DEM Pins
        2. 7.3.10.2 DEM Programming
        3. 7.3.10.3 FPWM Programming and Dynamic FPWM and DEM Change
        4. 7.3.10.4 SS Pin as the Restart Timer
      11. 7.3.11 Gate Drive Outputs, Dead Time Programming and Adaptive Dead Time (HO1, HO2, LO1, LO2, DT/SD)
      12. 7.3.12 Emergent Latched Shutdown (DT/SD)
      13. 7.3.13 PWM Comparator
      14. 7.3.14 Oscillator (OSC)
      15. 7.3.15 Synchronization to an External Clock (SYNCI, SYNCO)
      16. 7.3.16 Overvoltage Protection (OVP)
      17. 7.3.17 Multiphase Configurations (SYNCO, OPT)
        1. 7.3.17.1 Multiphase in Star Configuration
        2. 7.3.17.2 Daisy-Chain Configurations for 2, 3, or 4 Phases parallel operations
        3. 7.3.17.3 Daisy-Chain configuration for 6 or 8 phases parallel operation
      18. 7.3.18 Thermal Shutdown
    4. 7.4 Programming
      1. 7.4.1 Dynamic Dead Time Adjustment
      2. 7.4.2 UVLO Programming
    5. 7.5 I2C Serial Interface
      1. 7.5.1 REGFIELD Registers
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Small Signal Model
        1. 8.1.1.1 Current Loop Small Signal Model
        2. 8.1.1.2 Current Loop Compensation
        3. 8.1.1.3 Voltage Loop Small Signal Model
        4. 8.1.1.4 Voltage Loop Compensation
    2. 8.2 Typical Application
      1. 8.2.1 60-A, Dual-Phase, 48-V to 12-V Bidirectional Converter
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1  Determining the Duty Cycle
          2. 8.2.1.2.2  Oscillator Programming
          3. 8.2.1.2.3  Power Inductor, RMS and Peak Currents
          4. 8.2.1.2.4  Current Sense (RCS)
          5. 8.2.1.2.5  Current Setting Limits (ISETx)
          6. 8.2.1.2.6  Peak Current Limit
          7. 8.2.1.2.7  Power MOSFETS
          8. 8.2.1.2.8  Bias Supply
          9. 8.2.1.2.9  Boot Strap
          10. 8.2.1.2.10 OVP
          11. 8.2.1.2.11 Dead Time
          12. 8.2.1.2.12 Channel Current Monitor (IMONx)
          13. 8.2.1.2.13 UVLO Pin Usage
          14. 8.2.1.2.14 HVx Pin Configuration
          15. 8.2.1.2.15 Loop Compensation
          16. 8.2.1.2.16 Soft Start
          17. 8.2.1.2.17 PWM to ISET Pins
        3. 8.2.1.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Examples
  9. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
    2. 9.2 接收文档更新通知
    3. 9.3 支持资源
    4. 9.4 Trademarks
    5. 9.5 静电放电警告
    6. 9.6 术语表
  10. 10Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.3.5.1 Channel Enable Commands (EN1, EN2)

These pins are two state function pins. EN1 and EN2 are independent command signals. EN1 controls CH-1, and EN2 controls CH-2.

  1. When the EN1 pin voltage is pulled above 2 V (logic state of 1), the HO1 and LO1 outputs of the same channel are enabled through soft start programmed by SS/DEM1.
  2. When the EN1 pin voltage is pulled below 1 V (logic state of 0), CH-1 controller is disabled and both HO1 and LO1 outputs are turned off, and SS/DEM1 is discharged.
  3. Similar behaviors for EN2, HO2 and LO2, and SS/DEM2 of CH-2.
  4. When the EN1 and EN2 pins are left open, an internal 1000-kΩ pulldown resistor sets them to the low state.
  5. The built-in 2.5-µs glitch filters prevent errant operation due to the noise on the EN1 and EN2 signals.