无线微处理器
超低功耗传感器控制器
低功耗
无线协议支持
高性能无线电
法规遵从性
MCU 外设
信息安全机制
开发工具和软件
工作温度范围
封装
SimpleLink™ CC1312R7 器件是一款多协议 Sub-1GHz 无线微控制器 (MCU)，支持以下协议：IEEE 802.15.4g、支持 IPv6 的智能对象 (6LoWPAN)、 mioty 、 Wi-SUN 、专有系统（包括 TI 15.4-Stack (Sub-1GHz)）和通过动态多协议管理器 (DMM) 驱动器实现的并发多协议。 CC1312R7 基于 Arm® Cortex® M4F 主处理器，针对电网基础设施、楼宇自动化、零售自动化、 个人电子产品和医疗应用中的低功耗无线通信和高级传感功能进行了优化。
CC1312R7 具有由 Arm® Cortex® M0 驱动的软件定义无线电，支持多个物理层和射频标准。器件支持在 287MHz 至 351MHz、359MHz 至 527MHz、861MHz 至 1054MHz 以及 1076MHz 至 1315MHz 频带内运行。通过动态多协议管理器 (DMM) 驱动程序，可在运行时完成 PHY 和频带切换。 CC1312R7 具有高效的内置 PA，在电流消耗为 24.9mA 时 TX 支持 +14dBm 的输出功率。在 RX 中且在数据速率为 2.5kbps 的 SimpleLink™ 远距离模式下，该器件具有 -121dBm 的灵敏度和 88dB 的屏蔽性能 (±10MHz)。
在保持 144KB RAM 时， CC1312R7 具有 0.9µA 的低待机电流。除了 Cortex® M4F 主处理器，该器件还具有能够实现快速唤醒功能的自主式超低功耗传感器控制器 CPU。例如，传感器控制器能够在系统电流为 1µA 时进行 1Hz ADC 采样。
CC1312R7 具有低 SER（软错误率）FIT（时基故障），可延长运行寿命。SRAM 奇偶校验功能始终开启，可更大程度地降低因潜在辐射事件导致的损坏风险。许多客户对产品生命周期的要求为 10 至 15 年或者更久，为了达到这一目标，TI 制定了产品生命周期政策，对产品的寿命和供货连续性作出承诺。
CC1312R7 器件是 SimpleLink™ MCU 平台的一部分，包括 Wi-Fi®、低功耗 Bluetooth®、Thread、Zigbee、Wi-SUN®、Amazon Sidewalk、mioty®、Sub-1GHz MCU 和主机 MCU。 CC1312R7 是可扩展产品系列（闪存为 32KB 至 704KB）的一部分，具有引脚对引脚兼容的封装选项。通用 SimpleLink™ CC13xx 和 CC26xx 软件开发套件 (SDK) 及 SysConfig 系统配置工具支持产品系列中各器件之间的迁移。SDK 随附了丰富的软件栈、应用示例和 SimpleLink™ Academy 培训课程。有关更多信息，请查看无线连接。
如需其他信息或资源，请点击以下任一标题进入详情页面查看（如有）。
BDE Technology, Inc. 是 TI 认证的第三方模块提供商。BDE 的模块基于 TI 的 CC1XXX 低于 1GHz 无线连接产品，使客户能够缩短开发周期、减少设计不确定性、降低产品成本并高效发布具有竞争力的产品。BDE 专门向全球 OEM、系统集成商、设备制造商和解决方案提供商提供超低功耗无线通信技术，如 Amazon Sidewalk、Wi-SUN、mioty 和无线 M-Bus。
Lauterbach TRACE32® 工具是一套先进的硬件和软件组件，开发人员可通过它分析、优化和认证 TI 的许多无线连接芯片。这套全球知名的嵌入式系统调试解决方案是所有开发阶段（从器件前开发一直到产品认证和现场故障排除）的理想解决方案： 完整的片上断点支持；运行时存储器访问；闪存编程和基准测试计数器。所有功能均可脚本化，使开发人员能够反复执行相同的测试序列。Lauterbach 工具直观的模块化设计可为工程师提供当今最高的可用性能，并提供可随需求变化而调整和扩展的系统。经认证的工具资质认证支持套件 (TQSK) 提供了一种便捷而全面的方法来鉴定 TRACE32® (...)
此 LaunchPad™ 开发套件用于加快 SimpleLink™ Sub-1GHz CC1312R7 无线 MCU 的开发速度。SIMPLELINK-LOWPOWER-SDK 软件开发套件提供软件支持。
Amazon Sidewalk 是一个安全可靠的社区网络，它使用 Amazon Sidewalk 桥接器（例如兼容的 Amazon Echo 和 Ring 设备）覆盖家庭、楼宇、整个社区甚至整个城市的用例，为物联网设备提供云连接。Amazon Sidewalk 使用低功耗 Bluetooth® 进行短距离通信，使用 Sub-1GHz 915MHz 频率覆盖更远的距离，从而实现家庭内外的低带宽和远距离连接。Amazon Sidewalk 利用所使用的数百万个 Sidewalk (...)
WA12XX 系列是 UHF 高性能数字无线麦克风系统，集成了无线麦克风、激光棒、PPT 翻页器和其他功能。它可以在环境中自动搜索干净的信道，以供使用、快速锁定信道并消除干扰。同时，它还配备了红外频率配对模式，可承受恶劣的使用环境。该系列产品在 UHF 频段运行，完全避免了来自 Wifi/2.4G/700MHz/5.8G 的干扰。
The SimpleLink™ Low Power SDKs support the CC13xx, CC23xx and CC26xx family of products. Together, these SDKs provide comprehensive software packages for the development of Sub-1 GHz and 2.4 GHz applications including support for Bluetooth® Low Energy, Mesh, Zigbee®, Matter, Thread, 802.15.4-based, (...)
The TI-15.4-Stack-Gateway-Linux Software Development Kit (SDK) provides a Linux software middleware for the TI 15.4-Stack companion solution. It includes a full Linux user-space software that runs on top of the TI Processor SDK for AM335x platform, which interfaces with the co-processor embedded (...)
Sensor Controller Studio is used to write, test and debug code for the CC26xx/CC13xx Sensor Controller, enabling ultra-low power application design. The tool generates an interface driver consisting of C source files with the firmware image, associated definitions, and generic functions that allow (...)
CCStudio™ SysConfig is part of TI's extensive CCStudio™ development ecosystem and is a configuration tool that simplifies hardware and software configuration challenges to accelerate software development.
SysConfig provides an intuitive graphical user interface for configuring pins, peripherals, (...)
The SmartRF Packet Sniffer is a PC software application that can display and store radio packets captured by a listening RF device. The capture device is connected to the PC via USB. Various RF protocols are supported. The Packet Sniffer filters and decodes packets and displays them in a convenient (...)
SmartRF™ Studio is a Windows application that helps designers of RF systems to easily evaluate the radio at an early stage in the design process for all TI CC1xxx and CC2xxx low-power RF devices. It simplifies generation of the configuration register values and commands, as well as practical (...)
To get started with the SimpleLink™ Sub-1GHz hardware design review process:
| 封装 | 引脚 | CAD 符号、封装和 3D 模型 |
|---|---|---|
| VQFN (RGZ) | 48 | Ultra Librarian |
推荐产品可能包含与 TI 此产品相关的参数、评估模块或参考设计。
SmartRF Studio 7 in Cloud TI Resource Explorer
Compressed source file archive
SmartRF™ Studio is a Windows application that can be used to evaluate and configure Low Power RF devices from Texas Instruments. The application helps designers of RF systems to easily evaluate the radio at an early stage in the design process. It is especially useful for generation of configuration register values and commands, and for practical testing and debugging of the RF system. SmartRF Studio can be used either as a standalone application or together with applicable evaluation boards or debug probes for the RF device.
SmartRF Packet Sniffer 2 includes software and firmware to capture and display over-the-air packets. The capture device is connected to the PC via USB. SmartRF Packet Sniffer 2 supports the CC13xx and CC26xx family of devices as capture device and uses Wireshark for packet display and filtering.
Please note that device revision C (1.1) of CC13x2/CC26x2 is no longer supported. Download SmartRF Packet Sniffer 2 v1.6.0 if you use CC13x2/CC26x2 device revision C (1.1).
Hardware Design Review Request Form for SimpleLink Sub-1GHz Devices
None
Initial release of the SimpleLink CC13xx CC26xx Academy
Installer executable
Compressed archive
HTML document
Compressed source file archive
Sensor Controller Studio is used to write, test and debug code for the CC26xx/CC13xx Sensor Controller, allowing for ultra-low power application design.
The tool generates a Sensor Controller Interface driver, which is a set of C source files to be compiled into the System CPU (ARM Cortex-M3/M4) application. These source files contain the Sensor Controller firmware image and associated definitions, and generic functions that allow the System CPU application to control the Sensor Controller and exchange data.
The Sensor Controller is a small CPU core that is highly optimized for low power consumption and efficient peripheral operation. The Sensor Controller is located in the CC26xx/CC13xx auxiliary (AUX) power/clock domain, and can perform simple background tasks autonomously and independently of the System CPU and the MCU domain power state. Such tasks include but are not limited to:
The Sensor Controller is user programmable, using a simple programming language with syntax similar to C. This allows for sensor polling and other tasks to be specified as sequential algorithms, rather than static configuration of complex peripheral modules, timers, DMA, register programmable state machines, event routing and so on. The main advantages are:
TI 15.4-Stack is an IEEE 802.15.4-based software stack part of the SimpleLink Low Power F2 SDK that supports a Star network topology for wireless applications. TI 15.4-Stack provides a complete end-to-end wireless application development solution to reduce time and cost of getting your product to market.
The SimpleLink™ Low Power F2 Software Development Kit (SDK), formerly known as the CC13xx and CC26xx SDK, delivers components that enable engineers to develop applications on the Texas Instruments SimpleLink CC13xx and CC26xx family of wireless microcontrollers (MCUs). This software toolkit provides a cohesive and consistent software experience for all SimpleLink CC13xx and CC26xx wireless MCU users by packaging essential software components, such as a Bluetooth® Low Energy (LE) protocol stack supporting Bluetooth 5.2, Zigbee 3.0 compliant protocol suite, RF-Proprietary examples, TI 15.4 Stack, TI Wi-SUN FAN Stack, Amazon Sidewalk examples, as well as the TI-RTOS7 and FreeRTOS kernels and TI Drivers in one easy-to-use software package along with example applications and documentation. In addition, the Dynamic Multi-Protocol Manager (DMM) software component enables multiprotocol development on a single SimpleLink wireless MCU.
The SimpleLink MCU portfolio offers a single development environment that delivers flexible hardware, software, and tool options for customers developing wired and wireless applications. With 100 percent code reuse across host MCUs, Wi-Fi™, Bluetooth Low Energy, Sub-1GHz devices and more, choose the MCU or connectivity standard that fits your design. A one-time investment with the SimpleLink software development kit allows you to reuse often, opening the door to create unlimited applications. For more information, visit www.ti.com/simplelink.
This is version 8.32.00.07 of the SimpleLink Low Power F2 SDK. This SDK is also available on GitHub at https://github.com/TexasInstruments/simplelink-lowpower-f2-sdk .
The SysConfig tool is used configure TI software and hardware. For software configuration, SysConfig is used in conjunction with a TI SDK. For PinMux configuration, the tool may be used standalone.