SLWU079D March   2012  – April 2016

 

  1.   TSW140x High Speed Data Capture/Pattern Generator Card
    1.     Trademarks
    2. 1 Functionality
      1. 1.1 ADC EVM Data Capture
      2. 1.2 DAC EVM Pattern Generator
    3. 2 Hardware Configuration
      1. 2.1 Power Connections
        1. 2.1.1 Output Power Regulators
      2. 2.2 Switches, Jumpers and Fuses
        1. 2.2.1 Switches and Pushbuttons
        2. 2.2.2 Jumpers
        3. 2.2.3 Fuses
      3. 2.3 LEDs
      4. 2.4 Connectors
        1. 2.4.1 Input LVDS ADC Interface Connector
        2. 2.4.2 JTAG Connector
        3. 2.4.3 Input CMOS ADC Interface Connector
        4. 2.4.4 Output LVDS Connector
        5. 2.4.5 Output CMOS DAC Interface Connector
        6. 2.4.6 USB I/O Connection
    4. 3 Software Start up
      1. 3.1 Installation Instructions
      2. 3.2 USB Interface and Drivers
      3. 3.3 Device ini Files
    5. 4 ADC Data Capture Software Operation
      1. 4.1 Testing a TSW1400 EVM with an ADS5281 EVM
      2. 4.2 Testing a TSW1400EVM with an ADS62P49EVM (CMOS Interface)
    6. 5 TSW1400 Pattern Generator Operation
      1. 5.1 Testing a TSW1400 EVM with a DAC3152 EVM
      2. 5.2 Loading DAC Firmware
      3. 5.3 Configuring TSW1400 for Pattern Generation
      4. 5.4 Testing a TSW1400 EVM with a DAC5688EVM (CMOS Interface)
    7. 6 TSW1405 Functional Description
      1. 6.1 Hardware Description
        1. 6.1.1 Power Connections
        2. 6.1.2 Pushbuttons
        3. 6.1.3 Jumpers
        4. 6.1.4 LEDs
      2. 6.2 Software Operation
        1. 6.2.1 Channel Selection
    8. 7 TSW1406 Functional Description
      1. 7.1 Hardware Description
        1. 7.1.1 Power Connections
        2. 7.1.2 Pushbuttons
        3. 7.1.3 Jumpers
        4. 7.1.4 LEDs
      2. 7.2 Software Operation
    9. 8 Revision History

3.3 Device ini Files

Included in the installation for the HSDC Pro GUI software is a subdirectory of ini files for each category of ADC and DAC that is supported by the TSW140x EVMs. TI strongly recommends that these files are not edited except at the factory. These files contain necessary information for the GUI software to properly configure the TSW140x EVM FPGA registers for proper operation with the desired ADC or DAC EVM. Some of the entries within the ini file are obvious, such as defining the bit resolution for a device as 11, 12, 14, or 16 bits. Other entries in the ini file define for the FPGA which LVDS pairs within the Samtec connector define the data bus, and correct operation may not be possible if these entries are edited. The use of ini files allows for new device types to be supported by the TSW140x EVM as they become available without having to modify, re-release, or re-install the HSDC Pro GUI software. New device types may be supported at a later date simply by adding a new ini file to the proper subdirectory.