CC2650 器件是一款面向 Bluetooth Smart、 ZigBee和 6LoWPAN，以及 ZigBee RF4CE 远程控制 应用的无线 MCU。
此器件属于 CC26xx 系列的经济高效型超低功耗 2.4GHz RF 器件。它具有极低的有源 RF 和 MCU 电流以及低功耗模式流耗，可确保卓越的电池使用寿命，适合小型纽扣电池供电以及在能源采集型应用中 使用。
CC2650 器件含有一个 32 位 ARM Cortex-M3 处理器（与主处理器工作频率同为 48MHz），并且具有丰富的外设功能集，其中包括一个独特的超低功耗传感器控制器。此传感器控制器非常适合连接外部传感器，还适合用于在系统其余部分处于睡眠模式的情况下自主收集模拟和数字数据。因此，CC2650 器件成为 广泛的 工业、消费类电子和医疗产品中各类应用的理想选择。
Bluetooth 低能耗控制器和 IEEE 802.15.4 MAC 嵌入在 ROM 中，并在 ARM Cortex-M0 处理器上单独运行。此架构可改善整体系统性能和功耗，并释放闪存以供应用。
Bluetooth Smart 和 ZigBee 协议栈可从 www.ti.com.cn 免费获取。
如需其他信息或资源，请点击以下任一标题进入详情页面查看（如有）。
SimpleLink™ 低功耗 Bluetooth® CC2650 模块 BoosterPack 插件模块是一种快速简便的方法，可将低功耗蓝牙添加到 LaunchPad™ 开发套件中。只需将 CC2650 模块 BoosterPack 套件插入 MSP432™ 微控制器 (MCU) LaunchPad 套件，即可开始使用！此处提供了用于开始开发的软件示例。
CC2650 模块 BoosterPack 套件配有无线网络处理器软件，该软件允许您使用简单 UART 接口将低功耗蓝牙连接添加到任何应用。模块 BoosterPack 套件还包含一个 JTAG 连接，用于对 CC2650 (...)
μISP 既可以连接到主机 PC（内置 RS-232、USB 和 LAN 连接），也可以在独立模式下运行。
只需按下 START 按钮或通过某些 TTL 控制线，即可在独立模式下执行编程周期。
其紧凑的尺寸和多功能性便于集成到生产环境、手动和自动流程中。
SimpleLink™ CC2650 评估模块套件是 CC2650 开发套件的插件套件。此套件中包括的 CC2650 器件是 SimpleLink 超低功耗无线 MCU 平台的超集器件，因此还可用于评估 SimpleLink 蓝牙智能 CC2640 无线 MCU 和 6LoWPAN/ZigBee® CC2630 无线 MCU。此套件包括两个 CC2650 评估模块和一份入门指南。
CC2650EMK-7ID 评估模块包含无线 MCU 并显示采用 7x7mm 封装、内部偏置和差分射频输出（型号 7ID）的射频布局版本。
CC2650EMK-5XD 评估模块包含无线 MCU 并显示采用 5x5 mm (...)
XDS200 是用于调试 TI 嵌入式器件的调试探针（仿真器）。对于大多数器件，建议使用较新、成本较低的 XDS110 (www.ti.com/tool/TMDSEMU110-U)。XDS200 在单个仓体中支持更广泛的标准（IEEE1149.1、IEEE1149.7、SWD）。所有 XDS 调试探针在所有具有嵌入式跟踪缓冲器 (ETB) 的 Arm® 和 DSP 处理器中均支持内核和系统跟踪。
XDS200 通过 TI 20 引脚连接器（带有适用于 TI 14 引脚、Arm Cortex® 10 引脚和 Arm 20 引脚的多个适配器）连接到目标板，并通过 USB2.0 高速 (...)
Lauterbach TRACE32® 工具是一套先进的硬件和软件组件，开发人员可通过它分析、优化和认证 TI 的许多无线连接芯片。这套全球知名的嵌入式系统调试解决方案是所有开发阶段（从器件前开发一直到产品认证和现场故障排除）的理想解决方案： 完整的片上断点支持；运行时存储器访问；闪存编程和基准测试计数器。所有功能均可脚本化，使开发人员能够反复执行相同的测试序列。Lauterbach 工具直观的模块化设计可为工程师提供当今最高的可用性能，并提供可随需求变化而调整和扩展的系统。经认证的工具资质认证支持套件 (TQSK) 提供了一种便捷而全面的方法来鉴定 TRACE32® (...)
TASKING’s Debug, Trace, and Test tools offer comprehensive solutions for efficient debugging, tracing, and testing of TI's embedded systems. The scalable TASKING BlueBox debuggers allow users to easily flash, debug, and test across TI's portfolio. Development on TI hardware is made even easier with (...)
该新天线套件可用于进行真实测试，从而找到适合您应用的最佳天线！该天线套件包括 16 根天线（频率从 169MHz 到 2.4GHz），其中包括 PCB 天线、螺旋天线和芯片天线，以及 868/915MHz 结合 2.4GHz 的双频带天线。
此天线套件有一根 uSMA(JSC) 电缆，可以连接无线 LaunchPad 开发套件和 SensorTag。以下套件与 JSC 连接器兼容：
该套件还包含 uSMA(JSC)-SMA 连接器，用于将套件或天线连接到标准 SMA 连接器。
(...)
通过低功耗蓝牙连接到云，在 3 分钟内在线获得传感器数据。SensorTag 开箱即可使用，带有 iOS 和 Android 应用，无需编程经验即可开始操作。
全新的 SensorTag 基于 CC2650 无线 MCU，功耗比此前的低功耗蓝牙产品低 75%。因此，SensorTag 可由电池供电，而且一个纽扣电池可以工作多年。
低功耗蓝牙 SensorTag 包含 (...)
凭借 SimpleLink™ CC2650 无线微控制器 (MCU) LaunchPad 套件将您的 LaunchPad™ 开发套件推向云端。
CC2650 LaunchPad 套件采用 SimpleLink 超低功耗 CC26xx 系列器件，轻松实现与 LaunchPad 套件生态系统的低功耗蓝牙连接。该 LaunchPad (...)
AP6000, launched by Acroview, is a universal programmer designed to support TI ICs across all series. Leveraging Acroview's highly skilled algorithm R&D engineering team, it delivers the fastest chip support speed in the industry.The AP6000 is capable of programming 8 chips simultaneously, and (...)
AP8000 is a leading technology platform of Universal Programming developed by Acroview. We have an accomplished team of algorithm R&D engineers, to offer the fastest chip support software development service among the industry. The AP8000 can support the programming of 8 chips simultaneously. (...)
WriteNow! 系列系统内编程器是编程行业的突破性产品。该系列编程器支持来自不同制造商的众多器件（微控制器、存储器、CPLD 和其他可编程器件），并具有紧凑的尺寸，方便与 ATE/固定装置集成。它们可独立运行，也可连接到主机 PC（内置 RS-232、LAN 和 USB 连接），并附带易于使用的软件实用程序。
This royalty-free BLE-Stack for TI’s SimpleLink™ Bluetooth® Low Energy family of ARM® Cortex®-M3 based wireless microcontrollers (MCUs) includes full-featured Bluetooth 4.2 and Bluetooth 5 certified stacks with all necessary software, sample applications and documentation to (...)
To download the free tools download click the "Get Software" button above. By subscribing, we will be able to notify you of updates when they become available and provide instructions on how to perform the update.
CCStudio™ IDE is part of TI's extensive CCStudio™ development tool ecosystem. It is an integrated development environment (IDE) for TI's microcontrollers, processors, wireless connectivity devices and radar sensors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize (...)
Sensor Controller Studio is used to write, test and debug code for the CC26xx/CC13xx Sensor Controller, enabling ultra-low power application design. The tool generates an interface driver consisting of C source files with the firmware image, associated definitions, and generic functions that allow (...)
SysConfig is a configuration tool designed to simplify hardware and software configuration challenges to accelerate software development.
SysConfig is available as part of the Code Composer Studio™ integrated development environment as well as a standalone application. Additionally SysConfig (...)
The SimpleLink™ SDK Bluetooth Plugin is a companion software package that enables the use of a Bluetooth Network Processor (NWP) on a Host SimpleLink platform. This software package supports the MSP432P4, MSP432E4, and CC32xx devices as Host platforms, and the CC2650MODA, CC2640, and CC26x2R1 as (...)
SmartRF Flash Programmer 2 can be used to program the flash memory in Texas Instruments ARM based low-power RF wireless MCUs over the debug and serial interfaces. Check the list of supported products for compatibility. Uniflash can also be used to program any SimpleLink product.
SmartRF Flash (...)
UniFlash is a software tool for programming on-chip flash on TI microcontrollers and wireless connectivity devices and on-board flash for TI processors. UniFlash provides both graphical and command-line interfaces.
UniFlash can be run from the cloud on the TI Developer Zone or downloaded and used (...)
The SmartRF Packet Sniffer is a PC software application that can display and store radio packets captured by a listening RF device. The capture device is connected to the PC via USB. Various RF protocols are supported. The Packet Sniffer filters and decodes packets and displays them in a convenient (...)
SensorTag 包括适用于低成本和低功耗无线物联网应用的开放式硬件和软件参考设计。SensorTag 随完整源代码一起提供，具有应用定制所需的所有内容以及用于移动应用的源代码示例。
The SmartRF Packet Sniffer is a PC software application that can display and store radio packets captured by a listening RF device. The capture device is connected to the PC via USB. Various RF protocols are supported. The Packet Sniffer filters and decodes packets and displays them in a convenient (...)
SmartRF™ Studio is a Windows application that helps designers of RF systems to easily evaluate the radio at an early stage in the design process for all TI CC1xxx and CC2xxx low-power RF devices. It simplifies generation of the configuration register values and commands, as well as practical (...)
The SimpleLink hardware design review process provides a way to get in touch, one-on-one, with a subject matter expert that can help review your design and provide valuable feedback. A simple three-step process for requesting a review as well as links to relevant technical documentation and (...)
申请审查 2.4GHz 硬件设计前，应在我们的 E2E 论坛上提交一般设计问题。
请确保您已准备好所需的文档，随硬件设计审查申请表一起发送：
| 封装 | 引脚 | CAD 符号、封装和 3D 模型 |
|---|---|---|
| VQFN (RGZ) | 48 | Ultra Librarian |
| VQFN (RHB) | 32 | Ultra Librarian |
| VQFN (RSM) | 32 | Ultra Librarian |
推荐产品可能包含与 TI 此产品相关的参数、评估模块或参考设计。
Archive Installers for Simplelink BLE 2 x SDK
This is version 2.2.8 of the TI Bluetooth® low energy protocol stack Software Development Kit (SDK). The BLE-Stack SDK allows for the development of single-mode Bluetooth low energy (BLE) applications on TI's first generation SimpleLink Bluetooth low energy CC2640 and Multi-Standard CC2650 wireless microcontroller units (MCUs) supporting version 5.1 of the Bluetooth specification with features defined by version 4.2 of the Bluetooth specification. The CC26x0 family of wireless MCUs includes a 32-bit Arm® Cortex™-M3 as the main application CPU running at 48 MHz, a dedicated Cortex-M0 processor for the radio / Physical Layer (PHY), and an autonomous Sensor Controller Engine for low-power sensing applications. The BLE protocol stack is built on top of the TI Real-time Operating System (TI-RTOS) which provides advanced power management and flexible peripheral driver capabilities allowing the development of highly optimized and power efficient standalone or network processor applications. The TI-RTOS SDK is installed during the BLE-Stack SDK installation.
Version 2.2.8 of the BLE-Stack is a maintenance update to TI's existing royalty-free Bluetooth low energy software protocol stack which is certified for Bluetooth specification version 5.1. This release includes support for all core specification version 4.2 Low Energy (LE) features as well as several development kits. This protocol stack update is in addition to support of all major Bluetooth LE core specification version 4.1 features, including support for up to 8 master or slave BLE connections. Please note that no Bluetooth 5 or Bluetooth 5.1 features are supported. A few examples of what can be created using the sample applications in this SDK and/or the additional resources found in the Examples section below include Bluetooth beacons incorporating the popular Apple iBeacon® and Eddystone™ formats, glucose, heart rate and fitness monitors, dongles for cable replacement via a BLE Serial Port Bridge and industrial motor monitors.
See What's New section for an overview of the changes included in this release. The Bluetooth core specification version 4.2 features supported in this release allow development of the most secure and power efficient products incorporating the Bluetooth low energy specification.
SmartRF Studio 7 in Cloud TI Resource Explorer
Compressed source file archive
SmartRF™ Studio is a Windows application that can be used to evaluate and configure Low Power RF devices from Texas Instruments. The application helps designers of RF systems to easily evaluate the radio at an early stage in the design process. It is especially useful for generation of configuration register values and commands, and for practical testing and debugging of the RF system. SmartRF Studio can be used either as a standalone application or together with applicable evaluation boards or debug probes for the RF device.
This release adds the Power Estimator for CC23xx devices
Hardware Design Review Request Form for SimpleLink 2.4GHz Devices
查看产品详情页，验证是否能提供支持。
The Code Composer Studio™ IDE is a complete integrated suite that enables developers to create and debug applications of all Texas Instruments Embedded Processors (Sitara, DSP, Automotive, Keystone), Microcontrollers (SimpleLink™, C2000 Digital Control, MSP430, TM4C, Hercules), as well as Digital Power (UCD) and Programmable Gain Amplifier (PGA) devices.
CCS v20 is TI’s next generation Integrated Development Environment (IDE) based on Theia IDE framework. CCS v20.4.1 uses a modified version of the Theia-IDE framework and offers a user experience similar to Visual Studio Code™.
Zip file with Windows Installer and SW Manifest
Compressed source file archive
SmartRF Flash Programmer 2 can be used to program the flash memory in Texas Instruments ARM based low-power RF wireless MCUs over the debug and serial interfaces. The flash programmer includes both a graphical user interface and a command line interface.
Windows Installer for SimpleLink SDK BLE Plugin
macOS Installer for SimpleLink SDK BLE Plugin
Linux Installer for SimpleLink SDK BLE Plugin
SimpleLink SDK BLE Plugin User's Guide
The SimpleLink™ SDK BLE Plugin is a companion software package that enables the use of a Bluetooth radio on any standard MSP432P4 platform, MSP432E4 or CC32XX platform, and enables this two-chip solution to act as either a GAP Peripheral role or a GAP Central role. By having the ability to seamlessly and modularly add Bluetooth functionality (more specifically Bluetooth Low Energy/BLE) to an embedded system, a programmer can enable their embedded device to become a gateway to various IOT infrastructures.
For examples demonstrating the two-chip solution in a peripheral role, the plugin leverages the use of the TI Simple Application Processor (SAP) driver connected to a CC26xx Simple Network Processor (SNP) to provide a highly customizable hardware configuration. For software connectivity between the SAP and the SNP, an architecture agnostic HAL/Drivers layer is used to promote software portability and maximize collateral reuse.
For examples demonstrating the two-chip solution in a central role, communication between the NWP and the Host occurs through a UART serial interface using the Host Controller Interface (HCI) protocol. TI Vendor Specific HCI commands and a limited subset of Bluetooth LE HCI commands/events to implement a Bluetooth application. By using TI Vendor Specific commands and events, the application can communicate with and access the BLE stack.
SmartRF Packet Sniffer 2 includes software and firmware to capture and display over-the-air packets. The capture device is connected to the PC via USB. SmartRF Packet Sniffer 2 supports the CC13xx and CC26xx family of devices as capture device and uses Wireshark for packet display and filtering.
Please note that device revision C (1.1) of CC13x2/CC26x2 is no longer supported. Download SmartRF Packet Sniffer 2 v1.6.0 if you use CC13x2/CC26x2 device revision C (1.1).
UniFlash is a standalone tool used to program on-chip and external flash memory on TI MCUs and on-board flash memory for Sitara processors. UniFlash has a GUI, command line, and scripting interface. UniFlash is available free of charge.
None
Installer executable
Compressed archive
HTML document
Compressed source file archive
Sensor Controller Studio is used to write, test and debug code for the CC26xx/CC13xx Sensor Controller, allowing for ultra-low power application design.
The tool generates a Sensor Controller Interface driver, which is a set of C source files to be compiled into the System CPU (ARM Cortex-M3/M4) application. These source files contain the Sensor Controller firmware image and associated definitions, and generic functions that allow the System CPU application to control the Sensor Controller and exchange data.
The Sensor Controller is a small CPU core that is highly optimized for low power consumption and efficient peripheral operation. The Sensor Controller is located in the CC26xx/CC13xx auxiliary (AUX) power/clock domain, and can perform simple background tasks autonomously and independently of the System CPU and the MCU domain power state. Such tasks include but are not limited to:
The Sensor Controller is user programmable, using a simple programming language with syntax similar to C. This allows for sensor polling and other tasks to be specified as sequential algorithms, rather than static configuration of complex peripheral modules, timers, DMA, register programmable state machines, event routing and so on. The main advantages are:
The SysConfig tool is used configure TI software and hardware. For software configuration, SysConfig is used in conjunction with a TI SDK. For PinMux configuration, the tool may be used standalone.