ZHCSGZ6A October   2017  – February 2025 TPS6508700

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics: Total Current Consumption
    6. 5.6  Electrical Characteristics: Reference and Monitoring System
    7. 5.7  Electrical Characteristics: Buck Controllers
    8. 5.8  Electrical Characteristics: Synchronous Buck Converters
    9. 5.9  Electrical Characteristics: LDOs
    10. 5.10 Electrical Characteristics: Load Switches
    11. 5.11 Digital Signals: I2C Interface
    12. 5.12 Digital Input Signals (CTLx)
    13. 5.13 Digital Output Signals (IRQB, GPOx)
    14. 5.14 Timing Requirements
    15. 5.15 Switching Characteristics
    16. 5.16 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 SMPS Voltage Regulators
      1. 6.3.1 Controller Overview
      2. 6.3.2 Converter Overview
      3. 6.3.3 Dynamic Voltage Scaling
      4. 6.3.4 Current Limit
    4. 6.4 LDO Regulators and Load Switches
      1. 6.4.1 VTT LDO
      2. 6.4.2 LDOA1–LDOA3
      3. 6.4.3 Load Switches
    5. 6.5 Power Good Information (PGOOD or PG) and GPO Pins
    6. 6.6 Power Sequencing and Voltage-Rail Control
      1. 6.6.1 Power-Up and Power-Down Sequencing
      2. 6.6.2 Emergency Shutdown
    7. 6.7 Device Functional Modes
      1. 6.7.1 Off Mode
      2. 6.7.2 Standby Mode
      3. 6.7.3 Active Mode
    8. 6.8 I2C Interface
      1. 6.8.1 F/S-Mode Protocol
    9. 6.9 Register Maps
      1. 6.9.1  Register Map Summary
      2. 6.9.2  DEVICEID: PMIC Device and Revision ID Register (offset = 1h) [reset = 10h]
      3. 6.9.3  IRQ: PMIC Interrupt Register (offset = 2h) [reset = 0h]
      4. 6.9.4  IRQ_MASK: PMIC Interrupt Mask Register (offset = 3h) [reset = FFh]
      5. 6.9.5  PMICSTAT: PMIC Status Register (offset = 4h) [reset = 0h]
      6. 6.9.6  SHUTDNSRC: PMIC Shut-Down Event Register (offset = 5h) [reset = 0h]
      7. 6.9.7  BUCK2CTRL: BUCK2 Control Register (offset = 21h) [reset = 50h]
      8. 6.9.8  BUCK3DECAY: BUCK3 Decay Control Register (offset = 22h) [reset = 70h]
      9. 6.9.9  BUCK3VID: BUCK3 VID Register (offset = 23h) [reset = 70h]
      10. 6.9.10 BUCK3SLPCTRL: BUCK3 Sleep Control VID Register (offset = 24h) [reset = 70h]
      11. 6.9.11 BUCK4CTRL: BUCK4 Control Register (offset = 25h) [reset = Dh]
      12. 6.9.12 BUCK5CTRL: BUCK5 Control Register (offset = 26h) [reset = Dh]
      13. 6.9.13 BUCK6CTRL: BUCK6 Control Register (offset = 27h) [reset = Dh]
      14. 6.9.14 LDOA2CTRL: LDOA2 Control Register (offset = 28h) [reset = Ch]
      15. 6.9.15 LDOA3CTRL: LDOA3 Control Register (offset = 29h) [reset = 3Ch]
      16. 6.9.16 DISCHCTRL1: Discharge Control1 Register (offset = 40h) [reset = 55h]
      17. 6.9.17 DISCHCTRL2: Discharge Control2 Register (offset = 41h) [reset = 55h]
      18. 6.9.18 DISCHCTRL3: Discharge Control3 Register (offset = 42h) [reset = 15h]
      19. 6.9.19 PG_DELAY1: Power Good Delay1 Register (offset = 43h) [reset = 0h]
      20. 6.9.20 FORCESHUTDN: Force Emergency Shutdown Control Register (offset = 91h) [reset = 0h]
      21. 6.9.21 BUCK2SLPCTRL: BUCK2 Sleep Control Register (offset = 93h) [reset = 50h]
      22. 6.9.22 BUCK4VID: BUCK4 VID Register (offset = 94h) [reset = 20h]
      23. 6.9.23 BUCK4SLPVID: BUCK4 Sleep VID Register (offset = 95h) [reset = 20h]
      24. 6.9.24 BUCK5VID: BUCK5 VID Register (offset = 96h) [reset = 70h]
      25. 6.9.25 BUCK5SLPVID: BUCK5 Sleep VID Register (offset = 97h) [reset = E8h]
      26. 6.9.26 BUCK6VID: BUCK6 VID Register (offset = 98h) [reset = E8h]
      27. 6.9.27 BUCK6SLPVID: BUCK6 Sleep VID Register (offset = 99h) [reset = E8h]
      28. 6.9.28 LDOA2VID: LDOA2 VID Register (offset = 9Ah) [reset = FFh]
      29. 6.9.29 LDOA3VID: LDOA3 VID Register (offset = 9Bh) [reset = AAh]
      30. 6.9.30 BUCK123CTRL: BUCK1-3 Control Register (offset = 9Ch) [reset = 7h]
      31. 6.9.31 PG_DELAY2: Power Good Delay2 Register (offset = 9Dh) [reset = 21h]
      32. 6.9.32 SWVTT_DIS: SWVTT Disable Register (offset = 9Fh) [reset = E0h]
      33. 6.9.33 I2C_RAIL_EN1: VR Pin Enable Override1 Register (offset = A0h) [reset = 80h]
      34. 6.9.34 I2C_RAIL_EN2/GPOCTRL: VR Pin Enable Override2/GPO Control Register (offset = A1h) [reset = 89h]
      35. 6.9.35 PWR_FAULT_MASK1: VR Power Fault Mask1 Register (offset = A2h) [reset = C0h]
      36. 6.9.36 PWR_FAULT_MASK2: VR Power Fault Mask2 Register (offset = A3h) [reset = 3Fh]
      37. 6.9.37 GPO1PG_CTRL1: GPO1 PG Control1 Register (offset = A4h) [reset = C2h]
      38. 6.9.38 GPO1PG_CTRL2: GPO1 PG Control2 Register (offset = A5h) [reset = AFh]
      39. 6.9.39 GPO4PG_CTRL1: GPO4 PG Control1 Register (offset = A6h) [reset = 0h]
      40. 6.9.40 GPO4PG_CTRL2: GPO4 PG Control2 Register (offset = A7h) [reset = 0h]
      41. 6.9.41 GPO2PG_CTRL1: GPO2 PG Control1 Register (offset = A8h) [reset = C0h]
      42. 6.9.42 GPO2PG_CTRL2: GPO2 PG Control2 Register (offset = A9h) [reset = 2Fh]
      43. 6.9.43 GPO3PG_CTRL1: GPO3 PG Control1 Register (offset = AAh) [reset = 0h]
      44. 6.9.44 GPO3PG_CTRL2: GPO3 PG Control2 Register (offset = ABh) [reset = 0h]
      45. 6.9.45 MISCSYSPG Register (offset = ACh) [reset = FFh]
      46. 6.9.46 LDOA1CTRL: LDOA1 Control Register (offset = AEh) [reset = 7Dh]
      47. 6.9.47 PG_STATUS1: Power Good Status1 Register (offset = B0h) [reset = 0h]
      48. 6.9.48 PG_STATUS2: Power Good Status2 Register (offset = B1h) [reset = 0h]
      49. 6.9.49 PWR_FAULT_STATUS1: Power Fault Status1 Register (offset = B2h) [reset = 0h]
      50. 6.9.50 PWR_FAULT_STATUS2: Power Fault Status2 Register (offset = B3h) [reset = 0h]
      51. 6.9.51 TEMPCRIT: Temperature Fault Status Register (offset = B4h) [reset = 0h]
      52. 6.9.52 TEMPHOT: Temperature Hot Status Register (offset = B5h) [reset = 0h]
      53. 6.9.53 OC_STATUS: Overcurrent Fault Status Register (offset = B6h) [reset = 0h]
  8. 7 Applications, Implementation, and Layout
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Controller Design Procedure
          1. 7.2.2.1.1 Controller With External Feedback Resistor
          2. 7.2.2.1.2 Selecting the Inductor
          3. 7.2.2.1.3 Selecting the Output Capacitors
          4. 7.2.2.1.4 Selecting the FETs
          5. 7.2.2.1.5 Bootstrap Capacitor
          6. 7.2.2.1.6 Setting the Current Limit
          7. 7.2.2.1.7 Selecting the Input Capacitors
        2. 7.2.2.2 Converter Design Procedure
          1. 7.2.2.2.1 Selecting the Inductor
          2. 7.2.2.2.2 Selecting the Output Capacitors
          3. 7.2.2.2.3 Selecting the Input Capacitors
        3. 7.2.2.3 LDO Design Procedure
      3. 7.2.3 Application Curves
      4. 7.2.4 Layout
        1. 7.2.4.1 Layout Guidelines
        2. 7.2.4.2 Layout Example
    3. 7.3 Power Supply Coupling and Bulk Capacitors
    4. 7.4 Dos and Don'ts
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 接收文档更新通知
    4. 8.4 支持资源
    5. 8.5 Trademarks
    6. 8.6 静电放电警告
    7. 8.7 术语表
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

6.9.52 TEMPHOT: Temperature Hot Status Register (offset = B5h) [reset = 0h]

TEMPHOT is shown in Figure 6-65 and described in Table 6-59.

Return to Summary Table.

Asserted when an internal temperature sensor detects rise of die temperature above the HOT temperature threshold (THOT). There are 5 temperature sensors across the die.

Figure 6-65 TEMPHOT Register
76543210
RESERVEDDIE_HOTVTT_HOTTOP-RIGHT_HOTTOP-LEFT_HOTBOTTOM-RIGHT_HOT
R-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 6-59 TEMPHOT Field Descriptions
BitFieldTypeResetDescription
7-5RESERVEDR0h
4DIE_HOTR/W0h

Temperature of rest of die has exceeded THOT.

0h = Not asserted.

1h = Asserted. The host to write 1 to clear.

3VTT_HOTR/W0h

Temperature of VTT LDO has exceeded THOT.

0h = Not asserted.

1h = Asserted. The host to write 1 to clear.

2TOP-RIGHT_HOTR/W0h

Temperature of Top-Right has exceeded THOT. Top-Right corner of die from top view given pin1 is in Top-Left corner.

0h = Not asserted.

1h = Asserted. The host to write 1 to clear.

1TOP-LEFT_HOTR/W0h

Temperature of Top-Left has exceeded THOT. Top-Left corner of die from top view given pin1 is in Top-Left corner.

0h = Not asserted.

1h = Asserted. The host to write 1 to clear.

0BOTTOM-RIGHT_HOTR/W0h

Temperature of Bottom-Right has exceeded THOT. Bottom-Right corner of die from top view given pin1 is in Top-Left corner.

0h = Not asserted.

1h = Asserted. The host to write 1 to clear.