SLVSNH6 November 2026 DP83TC1104-Q1
PRODUCTION DATA
The DP83TC1104x-Q1 uses functional pins as strap options to place the device into specific modes of operation. The values of these pins are sampled at power up and hardware reset (through either the RESET pin or register access). Some strap pins support three levels and some strap pins support two levels, which are described in greater detail below. PHY address straps, RX_CTRL/RX_DV and RX_ER, are 3-level straps while all other straps are two levels. Configuration of the device can be done through strapping or through serial management interface.
Because strap pins are functional pins after reset is deasserted, do not connect the strap pins directly to VDDIO or GND. Either pullup resistors, pulldown resistors, or both are required for proper operation.
Rpulldn value is included in the Electrical Characteristics table of the datasheet.
| MODE(3) | IDEAL RH (kΩ) (VDDIO = 3.3V)(1) | IDEAL RH (kΩ) (VDDIO = 2.5V)(2) | IDEAL RH (kΩ) (VDDIO = 1.8V)(1) |
|---|---|---|---|
| 1 | OPEN | OPEN | OPEN |
| 2 | 13 | 12 | 4 |
| 3 | 4.5 | 2 | 0.8 |
The following table describes the PHY configuration bootstraps:
| STRAP NO. | PIN NAME |
PIN NO. | DOMAIN | DEFAULT MODE |
STRAP FUNCTION | DESCRIPTION | ||
|---|---|---|---|---|---|---|---|---|
| 0 | RX_CTRL / RX_DV | 25 | VDDIO | 1 | MODE | PHY_AD[0] | PHY_AD[2] | PHY_AD: PHY Address ID |
| 1 | 0 | 0 | ||||||
| 2 | 0 | 1 | ||||||
| 3 | 1 | 1 | ||||||
| 1 | RX_ER | 19 | VDDIO | 1 | MODE | PHY_AD[1] | PHY_AD[3] | PHY_AD: PHY Address ID |
| 1 | 0 | 0 | ||||||
| 2 | 0 | 1 | ||||||
| 3 | 1 | 1 | ||||||
| 2 | RX_D0 | 24 | VDDIO | 1 | MODE | MAC[0] | MAC: MAC Interface Selection | |
| 1 | 0 | |||||||
| 2 | 1 | |||||||
| 3 | RX_D1 | 23 | VDDIO | 1 | MODE | MAC[1] | MAC: MAC Interface Selection | |
| 1 | 0 | |||||||
| 2 | 1 | |||||||
| 4 | RX_D2 | 21 | VDDIO | 1 | MODE | MAC[2] | MAC: MAC Interface Selection | |
| 1 | 0 | |||||||
| 2 | 1 | |||||||
| 5 | LED_1 | 17 | VDDIO | 1 | MODE | AUTO | AUTO: Autonomous
Disable This is the default strap pin for controlling AUTO feature. |
|
| 1 | 0 | |||||||
| 2 | 1 | |||||||
| 6 | RX_CLK | 26 | VDDIO | 1 | MODE | TC10 | TC10 Disable: This pin strap decides if TC10 must be enabled or disabled | |
| 1 | 0 | |||||||
| 2 | 1 | |||||||
| STRAP NO. | PIN NAME |
PIN NO. | DOMAIN | DEFAULT MODE |
STRAP FUNCTION | DESCRIPTION | ||
|---|---|---|---|---|---|---|---|---|
| 0 | STRAP_0 | 25 | VDDIO | 1 | MODE | PHY_AD[0] | PHY_AD[2] | PHY_AD: PHY Address ID |
| 1 | 0 | 0 | ||||||
| 2 | 0 | 1 | ||||||
| 3 | 1 | 1 | ||||||
| 1 | STRAP_1 | 19 | VDDIO | 1 | MODE | PHY_AD[1] | PHY_AD[3] | PHY_AD: PHY Address ID |
| 1 | 0 | 0 | ||||||
| 2 | 0 | 1 | ||||||
| 3 | 1 | 1 | ||||||
| 2 | LED_1 | 17 | VDDIO | 1 | MODE | AUTO | AUTO: Autonomous
Disable This is the default strap pin for controlling AUTO feature. |
|
| 1 | 0 | |||||||
| 2 | 1 | |||||||
| AUTO | DESCRIPTION |
|---|---|
| 0 | Autonomous Mode, PHY able to establish link after power-up |
| 1 | Managed Mode, PHY must be allowed to establish link after power-up based on register write |
| TC10 | DESCRIPTION |
|---|---|
| 0 | TC10 is enabled |
| 1 | TC10 is disabled. This strap prevents PHY from transition to sleep mode. |
| MAC[2] | MAC[1] | MAC[0] | DESCRIPTION |
|---|---|---|---|
| 0 | 0 | 0 | Reserved |
| 0 | 0 | 1 | MII |
| 0 | 1 | 0 | RMII Follower(1) |
| 0 | 1 | 1 | RMII Leader |
| 1 | 0 | 0 | RGMII (Align Mode) |
| 1 | 0 | 1 | RGMII (TX Internal Delay Mode) |
| 1 | 1 | 0 | RGMII (TX and RX Internal Delay Mode) |
| 1 | 1 | 1 | RGMII (RX Internal Delay Mode) |
| PHY_AD[3:0] | STRAP_0 MODE | STRAP_1 MODE | DESCRIPTION Section 7.6.1 |
|---|---|---|---|
| 0000 | 1 | 1 | PHY Address: b0000 (0x0) |
| 0001 | - | - | NA |
| 0010 | - | - | NA |
| 0011 | - | - | NA |
| 0100 | 2 | 1 | PHY Address: b0100 (0x4) |
| 0101 | 3 | 1 | PHY Address: b0101 (0x5) |
| 0110 | - | - | NA |
| 0111 | - | - | NA |
| 1000 | 1 | 2 | PHY Address: b1000 (0x8) |
| 1001 | - | - | NA |
| 1010 | 1 | 3 | PHY Address: b1010 (0xA) |
| 1011 | - | - | NA |
| 1100 | 2 | 2 | PHY Address: b1010 (0xC) |
| 1101 | 3 | 2 | PHY Address: b1011 (0xD) |
| 1110 | 2 | 3 | PHY Address: b1110 (0xE) |
| 1111 | 3 | 3 | PHY Address: b1111 (0xF) |