SLVSNH6 November   2026 DP83TC1104-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
    1. 5.1 Pin Power Domain
    2. 5.2 Pin States
    3. 5.3 Pin Multiplexing
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Timing Diagrams
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 MAC Security Features
      2. 7.3.2 IEEE802.1AS Features
        1. 7.3.2.1 PTP Clock Configuration
          1. 7.3.2.1.1 PTP Reference Clock
          2. 7.3.2.1.2 PTP Synchronized Clock (Wall Clock)
            1. 7.3.2.1.2.1 PTP Time Read or Write
            2. 7.3.2.1.2.2 PTP Clock Initialization
            3. 7.3.2.1.2.3 PTP Clock Adjustment
            4. 7.3.2.1.2.4 PTP Clock Output
              1. 7.3.2.1.2.4.1 One Pulse Per Second (PPS) Output
          3. 7.3.2.1.3 PTP Time Registers
        2. 7.3.2.2 Packet Timestamps
          1. 7.3.2.2.1 Transmit (Egress) Packet Parser and Timestamp
          2. 7.3.2.2.2 Receive (Ingress) Packet Parser and Timestamp
          3. 7.3.2.2.3 PTP Transmit and Receive Timestamp Registers
        3. 7.3.2.3 Event Triggering and Timestamping
          1. 7.3.2.3.1 Event Triggering (Output)
            1. 7.3.2.3.1.1 Trigger Initialization
          2. 7.3.2.3.2 Event Timestamp (Input)
            1. 7.3.2.3.2.1 Timestamp Storage and Reading
          3. 7.3.2.3.3 Event Capture and Output Trigger Registers
        4. 7.3.2.4 PTP Interrupts
        5. 7.3.2.5 PTP I/O Configuration
      3. 7.3.3 TC10 Sleep Wake-up
        1. 7.3.3.1 Functions of the PHY for TC10 Support
          1. 7.3.3.1.1 Transition from Sleep to Wake-up Mode
            1. 7.3.3.1.1.1 Local Wake Detection
            2. 7.3.3.1.1.2 WUP Transmission and Reception
          2. 7.3.3.1.2 Wake Forwarding
          3. 7.3.3.1.3 Transition to Sleep - Sleep Negotiation
            1. 7.3.3.1.3.1 Sleep Ack
            2. 7.3.3.1.3.2 Sleep Request
            3. 7.3.3.1.3.3 Sleep Silent
            4. 7.3.3.1.3.4 Sleep Fail
            5. 7.3.3.1.3.5 Sleep
            6. 7.3.3.1.3.6 Force Sleep
        2. 7.3.3.2 Power Supply Networks for Sleep Applications
        3. 7.3.3.3 Configuration for Non-TC10 Applications
          1. 7.3.3.3.1 Hardware Configuration
          2. 7.3.3.3.2 Software Configuration
        4. 7.3.3.4 Miscellaneous Sleep Features
          1. 7.3.3.4.1 WUR Initiation Through WAKE Pin
          2. 7.3.3.4.2 Programmable Wake-Forward Pulse Duration
        5. 7.3.3.5 Fast Wake-up
          1. 7.3.3.5.1 Procedure To Program The Memory:
      4. 7.3.4 PPM Monitor
        1. 7.3.4.1 Configuring Interrupt for PPM Monitor Unlock
      5. 7.3.5 Clock Dithering
        1. 7.3.5.1 Impact of Dithering MAC Interface:
      6. 7.3.6 Diagnostic Toolkit
        1. 7.3.6.1 Signal Quality Indicator
        2. 7.3.6.2 Electrostatic Discharge Sensing
        3. 7.3.6.3 Time Domain Reflectometry
        4. 7.3.6.4 BIST and Loopback Modes
          1. 7.3.6.4.1 Data Generator and Checker
          2. 7.3.6.4.2 xMII Loopback
            1. 7.3.6.4.2.1 Enable Loopback
            2. 7.3.6.4.2.2 Enable Data Generator/Checker for MAC Side
            3. 7.3.6.4.2.3 Check Incoming Data From MAC Side
            4. 7.3.6.4.2.4 Enable Data Generator/Checker for Cable Side
            5. 7.3.6.4.2.5 Check Data for Cable Side
            6. 7.3.6.4.2.6 Other System Requirements
          3. 7.3.6.4.3 PCS Loopback
            1. 7.3.6.4.3.1 Enable Loopback
            2. 7.3.6.4.3.2 Enable Data Generator/Checker for MAC Side
            3. 7.3.6.4.3.3 Check Incoming Data From MAC Side
            4. 7.3.6.4.3.4 Enable Data Generator/Checker for Cable Side
            5. 7.3.6.4.3.5 Check Data for Cable Side
            6. 7.3.6.4.3.6 Other System Requirements
          4. 7.3.6.4.4 Digital Loopback
            1. 7.3.6.4.4.1 Enable Loopback
            2. 7.3.6.4.4.2 Enable Data Generator/Checker for MAC Side
            3. 7.3.6.4.4.3 Check Incoming Data From MAC Side
            4. 7.3.6.4.4.4 Enable Data Generator/Checker for Cable Side
            5. 7.3.6.4.4.5 Check Data for Cable Side
            6. 7.3.6.4.4.6 Other System Requirements
          5. 7.3.6.4.5 Analog Loopback
            1. 7.3.6.4.5.1 Enable Loopback
            2. 7.3.6.4.5.2 Enable Data Generator/Checker for MAC Side
            3. 7.3.6.4.5.3 Check Incoming Data From MAC Side
            4. 7.3.6.4.5.4 Enable Data Generator/Checker for Cable Side
            5. 7.3.6.4.5.5 Check Data for Cable Side
            6. 7.3.6.4.5.6 Other System Requirements
          6. 7.3.6.4.6 Reverse Loopback
            1. 7.3.6.4.6.1 Enable Loopback
            2. 7.3.6.4.6.2 Enable Data Generator/Checker for MAC Side
            3. 7.3.6.4.6.3 Check Incoming Data From MAC Side
            4. 7.3.6.4.6.4 Enable Data Generator/Checker for Cable Side
            5. 7.3.6.4.6.5 Check Data for Cable Side
            6. 7.3.6.4.6.6 Other System Requirements
      7. 7.3.7 Compliance Test Modes
        1. 7.3.7.1 Test Mode 1
        2. 7.3.7.2 Test Mode 2
        3. 7.3.7.3 Test Mode 4
        4. 7.3.7.4 Test Mode 5
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power Modes
        1. 7.4.1.1 Power Down
        2. 7.4.1.2 Reset
        3. 7.4.1.3 Standby
        4. 7.4.1.4 Normal
        5. 7.4.1.5 Sleep
      2. 7.4.2 Media Dependent Interface
        1. 7.4.2.1 100BASE-T1 Leader and 100BASE-T1 Follower Configuration
        2. 7.4.2.2 Auto-Polarity Detection and Correction
        3. 7.4.2.3 Jabber Detection
        4. 7.4.2.4 Interleave Detection
      3. 7.4.3 MAC Interfaces
        1. 7.4.3.1 Media Independent Interface
        2. 7.4.3.2 Reduced Media Independent Interface
        3. 7.4.3.3 Reduced Gigabit Media Independent Interface
        4. 7.4.3.4 Serial Gigabit Media Independent Interface
      4. 7.4.4 Serial Management Interface
        1. 7.4.4.1 Extended Register Space Access
        2. 7.4.4.2 Write Operation (No Post Increment)
        3. 7.4.4.3 Read Operation (No Post Increment)
        4. 7.4.4.4 Write Operation (Post Increment)
        5. 7.4.4.5 Read Operation (Post Increment)
    5. 7.5 Output Slew Control
    6. 7.6 Programming
      1. 7.6.1 Strap Configuration
      2. 7.6.2 LED Configuration
  9. 8 Register Maps
    1. 8.1 Register Access Summary
    2. 8.2 DP83TC1104x Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Physical Medium Attachment
          1. 9.2.1.1.1 Common-Mode Choke Recommendations
      2. 9.2.2 Detailed Design Procedure
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Signal Traces
        2. 9.4.1.2 Return Path
        3. 9.4.1.3 Metal Pour
        4. 9.4.1.4 PCB Layer Stacking
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Community Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)

Register Access Summary

There are two different methods for accessing registers within the field. Direct register access method is only allowed for the first 32 registers (0x0 through 0x1F). Registers beyond 0x1F must be accessed by use of the Indirect Method (Extended Register Space) described in Section 7.4.4.1.

Table 8-1 MMD Register Space Division
MMD REGISTER SPACEREGISTER ADDRESS RANGE
MMD1F0x0000 - 0x0FFF
MMD10x1000 - 0x1FFF
MMD30x3000 - 0x3FFF
Note: For MMD1 and MMD3, the most significant nibble of the register address is used to denote the respective MMD space. This nibble must be ignored during actual register access operation. For example, to access register 0x1836, use 0x1 as the MMD indicator and 0x0836 as the register address.
Table 8-2 Register Access Summary
REGISTER FIELDREGISTER ACCESS METHODS
0x0 through 0x1FDirect Access
Indirect Access, MMD1F = '11111'
Example: to read register 0x17 in MMD1F field with no post increment
Step 1) write 0x1F to register 0xD
Step 2) write 0x17 to register 0xE
Step 3) write 0x401F to register 0xD
Step 4) read register 0xE
MMD1F Field
0x20 - 0xFFF
Indirect Access, MMD1F = '11111'
Example: to read register 0x462 in MMD1F field with no post increment
Step 1) write 0x1F to register 0xD
Step 2) write 0x462 to register 0xE
Step 3) write 0x401F to register 0xD
Step 4) read register 0xE
MMD1 Field
0x0 - 0xFFF
Indirect Access, MMD1 = '00001'
Example: to read register 0x7 in MMD1 field (register 0x1007) with no post increment
Step 1) write 0x1 to register 0xD
Step 2) write 0x7 to register 0xE
Step 3) write 0x4001 to register 0xD
Step 4) read register 0xE