SLVSNH6 November 2026 DP83TC1104-Q1
PRODUCTION DATA
Table 8-3 lists the memory-mapped registers for the DP83TC1104x registers. All register offset addresses not listed in Table 8-3 should be considered as reserved locations and the register contents should not be modified.
| Offset | Acronym | Register Name | Section |
|---|---|---|---|
| 0h | BMCR | IEEE Control Register | Section 8.2.1 |
| 1h | BMSR | IEEE Status Register | Section 8.2.2 |
| 2h | PHYIDR1 | PHY Identification Register - 1 | Section 8.2.3 |
| 3h | PHYIDR2 | PHY Identification Register - 2 | Section 8.2.4 |
| 10h | PHYSTS | PHY Status Register | Section 8.2.5 |
| 11h | PHYSCR | Software Control Register | Section 8.2.6 |
| 12h | MISR1 | Interrupt Register -1 | Section 8.2.7 |
| 13h | MISR2 | Interrupt Register -2 | Section 8.2.8 |
| 15h | RECR | RX Error Count Register | Section 8.2.9 |
| 16h | BISCR | BIST Control Register | Section 8.2.10 |
| 17h | MISR4 | Interrupt Register -4 | Section 8.2.11 |
| 18h | MISR3 | Interrupt Register -3 | Section 8.2.12 |
| 19h | REG_19 | PHY Address Status Register | Section 8.2.13 |
| 1Ah | REG_1A | Receive Symbol Status Register | Section 8.2.14 |
| 1Bh | TC10_ABORT_REG | TC10 Abort Register | Section 8.2.15 |
| 1Eh | CDCR | TDR Run Status Register | Section 8.2.16 |
| 1Fh | PHYRCR | Reset Control Register | Section 8.2.17 |
| 133h | Register_133 | CnS Status Register | Section 8.2.18 |
| 134h | Register_134 | Start of Stream Delimiter Count Register | Section 8.2.19 |
| 135h | Register_135 | End of Stream Delimiter Count Register | Section 8.2.20 |
| 17Fh | Register_17F | WUR WUP Configuration Register | Section 8.2.21 |
| 181h | Register_181 | LPS Received Count Register | Section 8.2.22 |
| 182h | Register_182 | WUR Received Count Register | Section 8.2.23 |
| 184h | LPS_CFG | Low Power Configuration Register - 0 | Section 8.2.24 |
| 18Bh | LPS_CFG2 | Low Power Configuration Register - 2 | Section 8.2.25 |
| 18Ch | LPS_CFG3 | Low Power Configuration Register - 3 | Section 8.2.26 |
| 18Dh | LINK_FAIL_CNT | Link Fail Count Register | Section 8.2.27 |
| 18Eh | LPS_STATUS | Low Power Status Register | Section 8.2.28 |
| 1A0h | PCF | PHY Control Frame Configuration Register | Section 8.2.29 |
| 1A2h | MISC1 | SA DA Configuration Register | Section 8.2.30 |
| 1A3h | PPM0 | PPM Monitor Config Register - 0 | Section 8.2.31 |
| 1A4h | PPM1 | PPM Monitor Config Register - 1 | Section 8.2.32 |
| 1A5h | PPM2 | PPM Monitor Config Register - 2 | Section 8.2.33 |
| 1A6h | PPM3 | PPM Monitor Config Register - 3 | Section 8.2.34 |
| 1A7h | PPM4 | PPM Monitor Config Register - 4 | Section 8.2.35 |
| 1A8h | PPM5 | PPM Monitor Config Register - 5 | Section 8.2.36 |
| 1A9h | PPM6 | PPM Monitor Config Register - 6 | Section 8.2.37 |
| 1AAh | PPM7 | PPM Monitor Config Register - 7 | Section 8.2.38 |
| 1ADh | PPM10 | PPM Monitor Config Register - 10 | Section 8.2.39 |
| 1AEh | PPM11 | PPM Monitor Config Register - 11 | Section 8.2.40 |
| 1AFh | PPM12 | PPM Monitor Config Register - 12 | Section 8.2.41 |
| 1BEh | fwu_reg_3 | Fast Wake Up Register - 3 | Section 8.2.42 |
| 1D2h | spare_reg_tc10 | Fast Wake Up Spare Register | Section 8.2.43 |
| 306h | TDR_CFG5 | TDR Configuration Register - 5 | Section 8.2.44 |
| 310h | TDR_TC1 | TDR Status Register | Section 8.2.45 |
| 402h | ANA_LD_CTRL_3 | VDDIO Level Status Register | Section 8.2.46 |
| 430h | A2D_REG_48 | RGMII ID Control Register | Section 8.2.47 |
| 440h | A2D_REG_64 | ESD Event Count Register - 0 | Section 8.2.48 |
| 442h | A2D_REG_66 | ESD Event Count Register - 1 | Section 8.2.49 |
| 444h | A2D_REG_68 | TC10 Force Control Register | Section 8.2.50 |
| 450h | LEDS_CFG_1 | LED Configuration Register - 1 | Section 8.2.51 |
| 451h | LEDS_CFG_2 | LED Configuration Register - 2 | Section 8.2.52 |
| 452h | IO_MUX_CFG_1 | IO Multiplexing Register - 1 | Section 8.2.53 |
| 453h | IO_MUX_CFG_2 | IO Multiplexing Register - 2 | Section 8.2.54 |
| 456h | IO_MUX_CFG | xMII Impedance Control Register | Section 8.2.55 |
| 45Dh | CHIP_SOR_1 | Strap Status Register | Section 8.2.56 |
| 45Fh | LED1_CLKOUT_ANA_CTRL | CLKOUT and LED_1 Control Register | Section 8.2.57 |
| 460h | IMPEDANCE_CTRL_0 | Impedance Control Register - 0 | Section 8.2.58 |
| 4EEh | LINKUP_TIMER_1 | Link Up Timer Register - 1 | Section 8.2.59 |
| 4EFh | LINKUP_TIMER_2 | Link Up Timer Register - 2 | Section 8.2.60 |
| 523h | TX_PR_FILT_CTRL | MDI Transmit Force Register | Section 8.2.61 |
| 551h | PG_REG_1 | CRS_DV Control Register | Section 8.2.62 |
| 553h | PG_REG_4 | Auto-Polarity Correction Control Register | Section 8.2.63 |
| 561h | TC1_LINK_FAIL_LOSS | TC1 Link Fail Count Register | Section 8.2.64 |
| 562h | TC1_LINK_TRAINING_TIME | TC1 Link Training Time Register | Section 8.2.65 |
| 563h | NO_LINK_TH | No Link Interrupt TimeThreshold Register | Section 8.2.66 |
| 5A0h | DITH_CTRL_0 | Dithering Control Register - 0 | Section 8.2.67 |
| 5A1h | DITH_CTRL_1 | Dithering Control Register - 1 | Section 8.2.68 |
| 5A8h | DITH_RFI_EN_CTRL | Dithering Enable Register | Section 8.2.69 |
| 600h | RGMII_CTRL | RGMII Control Register | Section 8.2.70 |
| 601h | RGMII_FIFO_STATUS | RGMII FIFO Status Register | Section 8.2.71 |
| 602h | RGMII_CLK_SHIFT_CTRL | RGMII Shift Control Register | Section 8.2.72 |
| 608h | SGMII_CTRL_1 | SGMII Control Register - 1 | Section 8.2.73 |
| 60Ah | SGMII_STATUS | SGMII Status Register | Section 8.2.74 |
| 60Ch | SGMII_CTRL_2 | SGMII Control Register - 2 | Section 8.2.75 |
| 60Dh | SGMII_FIFO_STATUS | SGMII FIFO Status Register | Section 8.2.76 |
| 618h | PRBS_STATUS_1 | PRBS Status Register - 1 | Section 8.2.77 |
| 619h | PRBS_CTRL_1 | PRBS Control Register - 1 | Section 8.2.78 |
| 61Ah | PRBS_CTRL_2 | PRBS Control Register - 2 | Section 8.2.79 |
| 61Bh | PRBS_CTRL_3 | PRBS Control Register - 3 | Section 8.2.80 |
| 61Ch | PRBS_STATUS_2 | PRBS Status Register - 2 | Section 8.2.81 |
| 61Dh | PRBS_STATUS_3 | PRBS Status Register - 3 | Section 8.2.82 |
| 61Eh | PRBS_STATUS_4 | PRBS Status Register - 4 | Section 8.2.83 |
| 620h | PRBS_STATUS_5 | PRBS Status Register - 5 | Section 8.2.84 |
| 622h | PRBS_STATUS_6 | PRBS Status Register - 6 | Section 8.2.85 |
| 623h | PRBS_STATUS_7 | PRBS Status Register - 7 | Section 8.2.86 |
| 624h | PRBS_CTRL_4 | PRBS Control Register - 4 | Section 8.2.87 |
| 625h | PATTERN_CTRL_1 | BIST Pattern Control Register - 1 | Section 8.2.88 |
| 626h | PATTERN_CTRL_2 | BIST Pattern Control Register - 2 | Section 8.2.89 |
| 627h | PATTERN_CTRL_3 | BIST Pattern Control Register - 3 | Section 8.2.90 |
| 628h | PMATCH_CTRL_1 | BIST Match Control Register - 1 | Section 8.2.91 |
| 629h | PMATCH_CTRL_2 | BIST Match Control Register - 2 | Section 8.2.92 |
| 62Ah | PMATCH_CTRL_3 | BIST Match Control Register - 3 | Section 8.2.93 |
| 638h | PKT_CRC_STAT | BIST CRC Status Register | Section 8.2.94 |
| 639h | TX_PKT_CNT_1 | xMII TX Packet Count Register - 1 | Section 8.2.95 |
| 63Ah | TX_PKT_CNT_2 | xMII TX Packet Count Register - 2 | Section 8.2.96 |
| 63Bh | TX_PKT_CNT_3 | xMII TX Packet Count Register - 3 | Section 8.2.97 |
| 63Ch | RX_PKT_CNT_1 | xMII RX Packet Count Register - 1 | Section 8.2.98 |
| 63Dh | RX_PKT_CNT_2 | xMII RX Packet Count Register - 2 | Section 8.2.99 |
| 63Eh | RX_PKT_CNT_3 | xMII RX Packet Count Register - 3 | Section 8.2.100 |
| 648h | RMII_CTRL_1 | RMII Control Register | Section 8.2.101 |
| 649h | RMII_STATUS_1 | RMII FIFO Status Register | Section 8.2.102 |
| D00h | PTP_CTL | PTP Control Register | Section 8.2.103 |
| D01h | PTP_TDR | PTP Time Data Register | Section 8.2.104 |
| D02h | PTP_STS | PTP Status Register | Section 8.2.105 |
| D03h | PTP_TSTS | PTP Trigger Status Register | Section 8.2.106 |
| D04h | PTP_RATEL | PTP Rate Low Register | Section 8.2.107 |
| D05h | PTP_RATEH | PTP Rate High Register | Section 8.2.108 |
| D08h | PTP_TXTS | PTP Transmit Timestamp Register | Section 8.2.109 |
| D09h | PTP_RXTS | PTP Receive Timestamp Register | Section 8.2.110 |
| D0Ah | PTP_ESTS | PTP Event Status Register | Section 8.2.111 |
| D0Bh | PTP_EDATA | PTP Event Data Register | Section 8.2.112 |
| D0Bh | PTP_EDATA_ES | PTP Event Data Register Event Status | Section 8.2.113 |
| D10h | PTP_TRIG | PTP Trigger Configuration Register | Section 8.2.114 |
| D11h | PTP_EVNT | PTP Event Configuration Register | Section 8.2.115 |
| D12h | PTP_TXCFG0 | PTP Transmit Configuration Register 0 | Section 8.2.116 |
| D13h | PTP_TXCFG1 | PTP Transmit Configuration Register 1 | Section 8.2.117 |
| D14h | PSF_CFG0 | PHY Status Frame Configuration Register 0 | Section 8.2.118 |
| D15h | PTP_RXCFG0 | PTP Receive Configuration Register 0 | Section 8.2.119 |
| D16h | PTP_RXCFG1 | PTP Receive Configuration Register 1 | Section 8.2.120 |
| D17h | PTP_RXCFG2 | PTP Receive Configuration Register 2 | Section 8.2.121 |
| D18h | PTP_RXCFG3 | PTP Receive Configuration Register 3 | Section 8.2.122 |
| D19h | PTP_RXCFG4 | PTP Receive Configuration Register 4 | Section 8.2.123 |
| D1Ah | PTP_TRDL | PTP Temporary Rate Duration Low Register | Section 8.2.124 |
| D1Bh | PTP_TRDH | PTP Temporary Rate Duration High Register | Section 8.2.125 |
| D1Ch | PTP_EVNT_TSU_CFG | Event Timestamp Storage Configuration | Section 8.2.126 |
| D20h | PTP_COC | PTP Clock Output Control Register | Section 8.2.127 |
| D21h | PSF_CFG1 | Phy Status Frame Configuration Register 1 | Section 8.2.128 |
| D22h | PSF_CFG2 | Phy Status Frame Configuration Register 2 | Section 8.2.129 |
| D23h | PSF_CFG3 | Phy Status Frame Configuration Register 3 | Section 8.2.130 |
| D24h | PSF_CFG4 | Phy Status Frame Configuration Register 4 | Section 8.2.131 |
| D26h | PTP_INTCTL | PTP Interrupt Control Register | Section 8.2.132 |
| D27h | PTP_CLKSRC | PTP Clock Source Register | Section 8.2.133 |
| D28h | PTP_ETYPE | PTP Ethernet Type Register | Section 8.2.134 |
| D29h | PTP_OFF | PTP Offset Register | Section 8.2.135 |
| D2Bh | PTP_RXHASH | PTP Receive Hash Register | Section 8.2.136 |
| D30h | PTP_EVENT_GPIO_SEL | PTP Event GPIO selection | Section 8.2.137 |
| D32h | TX_SMD_GPIO_CTL | TX path SMD detection and GPIO control | Section 8.2.138 |
| D33h | SCH_CTL_1 | Scheduler control 1 | Section 8.2.139 |
| D34h | SCH_CTL_2 | Scheduler control 2 | Section 8.2.140 |
| D35h | FREQ_CTL_1 | Base frequency control 1 | Section 8.2.141 |
| D36h | FREQ_CTL_2 | Base frequency control 2 | Section 8.2.142 |
| D37h | PTP_RATEL_ACC_ONLY | PTP Rate ACC only LSB Register | Section 8.2.143 |
| D38h | PTP_RATEH_ACC_ONLY | PTP Rate ACC only MSB Register and enable | Section 8.2.144 |
| D39h | PTP_PLL_CTL | PTP_PLL control register | Section 8.2.145 |
| D3Ah | PTP_PLL_RD_1 | PTP timestamp read register 1 | Section 8.2.146 |
| D3Bh | PTP_PLL_RD_2 | PTP timestamp read register 2 | Section 8.2.147 |
| D3Ch | PTP_PLL_RD_3 | PTP timestamp read register 3 | Section 8.2.148 |
| D3Dh | PTP_PLL_RD_4 | PTP timestamp read register 4 | Section 8.2.149 |
| D3Eh | PTP_PLL_RD_5 | PTP timestamp read register 5 | Section 8.2.150 |
| D3Fh | PTP_PLL_RD_6 | PTP timestamp read register 6 | Section 8.2.151 |
| D40h | PTP_ONESTEP_OFF | PTP ONESTEP OFFSET register | Section 8.2.152 |
| D41h | PTP_PLL_FORCE_CTRL_1 | PTP_PLL Force control 1 | Section 8.2.153 |
| D42h | PTP_PLL_FORCE_CTRL_2 | PTP_PLL Force control 2 | Section 8.2.154 |
| D43h | PTP_PLL_FORCE_CTRL_3 | PTP_PLL Force control 3 | Section 8.2.155 |
| D45h | PTP_PSF_VLAN_CFG_1 | PSF VLAN Configuration 1 | Section 8.2.156 |
| D46h | PTP_PSF_VLAN_CFG_2 | PSF VLAN Configuration 2 | Section 8.2.157 |
| D47h | PTP_PSF_VLAN_CFG_3 | PSF VLAN Configuration 3 | Section 8.2.158 |
| DE0h | PTP_LAT_COMP_CTRL | PTP Latency Compensation Control | Section 8.2.159 |
| DF0h | PTP_DEBUG_SEL | PTP Debug Select | Section 8.2.160 |
| 1000h | MMD1_PMA_CTRL_1 | Section 8.2.161 | |
| 1001h | MMD1_PMA_STATUS_1 | Section 8.2.162 | |
| 1007h | MMD1_PMA_STAUS_2 | Section 8.2.163 | |
| 100Bh | MMD1_PMA_EXT_ABILITY_1 | Section 8.2.164 | |
| 1012h | MMD1_PMA_EXT_ABILITY_2 | Section 8.2.165 | |
| 1834h | MMD1_PMA_CTRL_2 | Section 8.2.166 | |
| 1836h | MMD1_PMA_TEST_MODE_CTRL | Section 8.2.167 | |
| 3000h | MMD3_PCS_CTRL_1 | Section 8.2.168 | |
| 3001h | MMD3_PCS_Status_1 | Section 8.2.169 |
Complex bit access types are encoded to fit into small table cells. Table 8-4 shows the codes that are used for access types in this section.
| Access Type | Code | Description |
|---|---|---|
| Read Type | ||
| R | R | Read |
| R-0 | R -0 | Read Returns 0s |
| RC | R C | Read to Clear |
| RH | R H | Read Set or cleared by hardware |
| Write Type | ||
| W | W | Write |
| W1S | W 1S | Write 1 to set |
| WSC | W | Write |
| Reset or Default Value | ||
| -n | Value after reset or the default value | |
BMCR is shown in Figure 8-1 and described in Table 8-5.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| MII Reset | MII Loopback Enable | Speed Select | Auto-Negotiation Enable | IEEE Power Down Enable | MAC Isolate Enable | RESERVED | Duplex Mode Select |
| R-0/W1S-0h | R/W-0h | R-1h | R-0h | R/W-0h | R/W-0h | R-0h | R-1h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | ||||||
| R-0h | R-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | MII Reset | R-0/W1S | 0h | 1b = Digital in reset and all MII regs
(0x0 - 0xF) reset to default 0b = No reset This bit is auto-cleared |
| 14 | MII Loopback Enable | R/W | 0h | 1b = Enable MII loopback 0b = Disable MII loopback When xMII loopback mode is activated, the transmitted data presented on xMII TXD is looped back to xMII RXD internally. There is no LINK indication generated when xMII loopback is enabled. |
| 13 | Speed Select | R | 1h | 1b= 100Mb/s 0b = Reserved |
| 12 | Auto-Negotiation Enable | R | 0h | Auto-Negotiation: Not supported on this device |
| 11 | IEEE Power Down Enable | R/W | 0h | This bit can be programmed to enter and
exit IEEE power down mode This bit provide status when using INT_N as power down pin 1b = Power down mode 0b = Normal mode |
| 10 | MAC Isolate Enable | R/W | 0h | 1b = Isolate mode (No output from PHY
to MAC) 0b = Normal mode |
| 9 | RESERVED | R | 0h | Reserved |
| 8 | Duplex Mode Select | R | 1h | 1b = Full duplex 0b = Half duplex |
| 7 | RESERVED | R | 0h | Reserved |
| 6-0 | RESERVED | R | 0h | Reserved |
BMSR is shown in Figure 8-2 and described in Table 8-6.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| 100Base-T4 Support | 100Base-X Full Duplex Support | 100Base-X Half Duplex Support | 10Mbps Full Duplex Support | 10Mbps Half Duplex Support | RESERVED | ||
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | SMI Preamble Suppresion | RESERVED | RESERVED | Auto-Negotiation Ability | Link status (Latch Low) | Jabber detect | Extended Register Capability |
| R-0h | R-1h | R-0h | R-0h | R-0h | RH-0h | RC-0h | R-1h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | 100Base-T4 Support | R | 0h | 0b = PHY doesn't support 100BASE-T4 |
| 14 | 100Base-X Full Duplex Support | R | 0h | 0b = PHY doesn't support full duplex 100BASE-X |
| 13 | 100Base-X Half Duplex Support | R | 0h | 0b = PHY doesn't support half duplex 100BASE-X |
| 12 | 10Mbps Full Duplex Support | R | 0h | 0b = PHY doesn't support 10Mb/s in full duplex mode |
| 11 | 10Mbps Half Duplex Support | R | 0h | 0b = PHY doesn't support 10Mb/s in half duplex mode |
| 10-7 | RESERVED | R | 0h | Reserved |
| 6 | SMI Preamble Suppresion | R | 1h | 1b = PHY will accept management frames
with preamble suppressed. 0b = PHY will not accept management frames with preamble suppressed |
| 5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3 | Auto-Negotiation Ability | R | 0h | 0b = PHY doesn't Auto-Negotiation |
| 2 | Link status (Latch Low) | RH | 0h | 1b = Link is up 0b = Link is down atleast once |
| 1 | Jabber detect | RC | 0h | 1b = Jabber condition detected 0b = No Jabber condition detected |
| 0 | Extended Register Capability | R | 1h | 1b = Extended register capabilities 0b = Basic register set capabilities only |
PHYIDR1 is shown in Figure 8-3 and described in Table 8-7.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Organizationally Unique Identifier 1 | |||||||
| R-2000h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Organizationally Unique Identifier 1 | |||||||
| R-2000h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Organizationally Unique Identifier 1 | R | 2000h | Unique Identifier for the part |
PHYIDR2 is shown in Figure 8-4 and described in Table 8-8.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Unique Identifier 2 | Model Number | ||||||
| R-28h | R-2Bh | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Model Number | Revision Number | ||||||
| R-2Bh | R-2h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-10 | Unique Identifier 2 | R | 28h | Unique Identifier for the part |
| 9-4 | Model Number | R | 2Bh | Unique Identifier for the part |
| 3-0 | Revision Number | R | 2h | Unique Identifier for the part |
PHYSTS is shown in Figure 8-5 and described in Table 8-9.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | Descrambler Lock Status (Latch Low) | RESERVED |
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | RH-0h | R-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Interrupt Pin Status | RESERVED | RESERVED | RESERVED | MII Loopback Status | Duplex Mode Status | RESERVED | Link Status (Latch Low) Non-Clear on Read |
| R-0h | R-0h | R-0h | R-0h | R-0h | R-1h | R-0h | R-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | RESERVED | R | 0h | Reserved |
| 13 | RESERVED | R | 0h | Reserved |
| 12 | RESERVED | R | 0h | Reserved |
| 11 | RESERVED | R | 0h | Reserved |
| 10 | RESERVED | R | 0h | Reserved |
| 9 | Descrambler Lock Status (Latch Low) | RH | 0h | 1b = Descrambler is locked 0b = Descrmabler is unlocked atleast once |
| 8 | RESERVED | R | 0h | Reserved |
| 7 | Interrupt Pin Status | R | 0h | Interrupts pin status, cleared on
reading 0x12 1b = Interrupts pin not set 0b = Interrupt pin had been set |
| 6 | RESERVED | R | 0h | Reserved |
| 5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3 | MII Loopback Status | R | 0h | 1b = MII loopback enabled 0b = MII loopback disabled |
| 2 | Duplex Mode Status | R | 1h | 1b = Full duplex 0b = Half duplex |
| 1 | RESERVED | R | 0h | Reserved |
| 0 | Link Status (Latch Low) Non-Clear on Read | R | 0h | Non-Clear on Read Latch Low link
status 1b = link is up 0b = link is down atleast once Status is cleared on reading reg0x1 |
PHYSCR is shown in Figure 8-6 and described in Table 8-10.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | SGMII Soft Reset | MAC Isolate for PHY_ADDR 0x00 | RMII TX FIFO Depth | ||
| R-0h | R-0h | R-0h | R/WSC-0h | R/W-0h | R/W-1h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | Interrupt Polarity | Force Interrupt | Interrupts Enable | Interrupt Pin Configuration | ||
| R-0h | R-0h | R/W-1h | R/W-0h | R/W-1h | R/W-1h | ||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | RESERVED | R | 0h | Reserved |
| 13-12 | RESERVED | R | 0h | Reserved |
| 11 | SGMII Soft Reset | R/WSC | 0h | SGMII Digital Reset This bit is auto-cleared |
| 10 | MAC Isolate for PHY_ADDR 0x00 | R/W | 0h | MAC Isolate is enabled only if PHY
address is 0x00 Reg0x0[10] works for all PHY addresses including 0x00 1b = Isolate mode (No output from PHY to MAC) 0b = Normal mode |
| 9-8 | RMII TX FIFO Depth | R/W | 1h | 00b = 4 nibbles 01b = 5 nibbles 10b = 6 nibbles 11b = 8 nibbles |
| 7 | RESERVED | R | 0h | Reserved |
| 6-4 | RESERVED | R | 0h | Reserved |
| 3 | Interrupt Polarity | R/W | 1h | 1b = Active low 0b = Active high |
| 2 | Force Interrupt | R/W | 0h | 1b = Force interrupt pin |
| 1 | Interrupts Enable | R/W | 1h | 1b = Enable interrupts 0b = Disable interrupts |
| 0 | Interrupt Pin Configuration | R/W | 1h | 1b = Configure INT_N pin is as
interrupt output pin 0b = Configure INT_N pin as power down input pin |
MISR1 is shown in Figure 8-7 and described in Table 8-11.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Energy Detect Change Status | Link Status Change Status | Wake on LAN Status | ESD Fault Detected Status | Training Done Status | RESERVED | RX Error Counter Half Full Status |
| R-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | R-0h | RC-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Energy Detect Change Indication | Link Status Change Indication | Wake on LAN Indication | ESD Fault Detected Indication | Training Done Indication | RESERVED | RX Error Counter Half Full Indication |
| R-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R-0h | R/W-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | Energy Detect Change Status | RC | 0h | Status is changed to 1 when there is a
change of MDI Energy detection output Status is cleared on read of this register |
| 13 | Link Status Change Status | RC | 0h | Status is changed to 1 when there is a
change of link status Status is cleared on read of this register |
| 12 | Wake on LAN Status | RC | 0h | Status is changed to 1 when WOL is is
received Status is cleared on read of this register |
| 11 | ESD Fault Detected Status | RC | 0h | Status is changed to 1 when ESD fault
is detected Status is cleared on read of this register |
| 10 | Training Done Status | RC | 0h | Status is changed to 1 when training is
done Status is cleared on read of this register |
| 9 | RESERVED | R | 0h | Reserved |
| 8 | RX Error Counter Half Full Status | RC | 0h | Status is changed to 1 when RX Error
Counter in 0x15 is half full Status is cleared on read of this register |
| 7 | RESERVED | R | 0h | Reserved |
| 6 | Energy Detect Change Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 5 | Link Status Change Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 4 | Wake on LAN Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 3 | ESD Fault Detected Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 2 | Training Done Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 1 | RESERVED | R | 0h | Reserved |
| 0 | RX Error Counter Half Full Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
MISR2 is shown in Figure 8-8 and described in Table 8-12.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Under Voltage Status | Over Voltage Status | RESERVED | RESERVED | Over Temperature Status | RESERVED | Data Polarity Change Status | Jabber Detect Status |
| RC-0h | RC-0h | R-0h | R-0h | RC-0h | R-0h | RC-0h | RC-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Under Voltage Indication | Over Voltage Indication | RESERVED | RESERVED | RESERVED | RESERVED | Data Polarity Change Indication | Jabber Detect Indication |
| R/W-0h | R/W-0h | R-0h | R-0h | R-0h | R-0h | R/W-0h | R/W-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Under Voltage Status | RC | 0h | Status is changed to 1 when Under
Voltage is detected Status is cleared on read of this register |
| 14 | Over Voltage Status | RC | 0h | Status is changed to 1 when Over
Voltage is detected Status is cleared on read of this register |
| 13 | RESERVED | R | 0h | Reserved |
| 12 | RESERVED | R | 0h | Reserved |
| 11 | Over Temperature Status | RC | 0h | Status is changed to 1 when Over
Temperature is detected Status is cleared on read of this register |
| 10 | RESERVED | R | 0h | Reserved |
| 9 | Data Polarity Change Status | RC | 0h | Status is changed to 1 when MDI lines
polairty change is detected Status is cleared on read of this register |
| 8 | Jabber Detect Status | RC | 0h | Status is changed to 1 when jabber is
detected Status is cleared on read of this register |
| 7 | Under Voltage Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 6 | Over Voltage Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2 | RESERVED | R | 0h | Reserved |
| 1 | Data Polarity Change Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 0 | Jabber Detect Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
RECR is shown in Figure 8-9 and described in Table 8-13.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RX Error Count | |||||||
| RC-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RX Error Count | |||||||
| RC-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | RX Error Count | RC | 0h | RX_ER Counter: When a valid carrier is presented (only while RX_DV is set), and there is at least one occurrence of an invalid data symbol, this 16-bit counter increments for each receive error detected. The RX_ER counter does not count in xMII loopback mode. The counter stops when it reaches its maximum count (0xFFFF). When the counter exceeds half-full (0x7FFF), an interrupt is generated. This register is cleared on read. |
BISCR is shown in Figure 8-10 and described in Table 8-14.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | RESERVED | ||||
| R-0h | R-0h | R-0h | R-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Data Transmission to MDI in xMII Loopback | Loopback Mode | PCS Loopback Enable | RESERVED | |||
| R-0h | R/W-0h | R/W-0h | R/W-0h | R-0h | |||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-11 | RESERVED | R | 0h | Reserved |
| 10 | RESERVED | R | 0h | Reserved |
| 9 | RESERVED | R | 0h | Reserved |
| 8 | RESERVED | R | 0h | Reserved |
| 7 | RESERVED | R | 0h | Reserved |
| 6 | Data Transmission to MDI in xMII Loopback | R/W | 0h | 0b = Suppress data to MDI during xMII
loopback 1b = Transmit data to MDI during xMII loopback |
| 5-2 | Loopback Mode | R/W | 0h | Enable Loopbacks other than PCS
loopback. 0x16[1] should be 0 0001b = Digital Loopback 0010b = Analog Loopback 0100b = Reverse Loopback 1000b = External Loopback |
| 1 | PCS Loopback Enable | R/W | 0h | 0b = Disable PCS Loopback 1b = Enable PCS Loopback |
| 0 | RESERVED | R | 0h | Reserved |
MISR4 is shown in Figure 8-11 and described in Table 8-15.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | PPM Monitor Unlock Status | RESERVED | |||||
| R-0h | R-0h | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | PPM Monitor Unlock Indication | RESERVED | |||||
| R-0h | R/W-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-12 | RESERVED | R | 0h | Reserved |
| 11 | PPM Monitor Unlock Status | R | 0h | Status is changed to 1 when PPM Monitor unlocks Status is cleared on read of this register |
| 10-4 | RESERVED | R | 0h | Reserved |
| 3 | PPM Monitor Unlock Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 2-0 | RESERVED | R | 0h | Reserved |
MISR3 is shown in Figure 8-12 and described in Table 8-16.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | No Link Status | Sleep Fail Status | Power-On Reset Done Status | No Frame Status | WUR Received Status | Remote Wake-up Indication | LPS Received Status |
| R-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | No Link Indication | Sleep Fail Indication | Power-On Reset Done Indication | No Frame Indication | WUR Received Indication | RESERVED | LPS Received Indication |
| R-0h | R/W-0h | R/W-1h | R/W-1h | R/W-0h | R/W-1h | R-0h | R/W-1h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | No Link Status | RC | 0h | Status is changed to 1 when Link has
not been observed within time programmed in 0x563
after training starts Status is cleared on read of this register |
| 13 | Sleep Fail Status | RC | 0h | Status is changed to 1 when Sleep
Negotiation Fails Status is cleared on read of this register |
| 12 | Power-On Reset Done Status | RC | 0h | Status is changed to 1 Power-On Reset
is done after the the supplies are up Status is cleared on read of this register |
| 11 | No Frame Status | RC | 0h | Status is changed to 1 when No frame is
detected until Status is cleared on read of this register |
| 10 | WUR Received Status | RC | 0h | Status is changed to 1 when WUR command
is received from link partner Status is cleared on read of this register |
| 9 | Remote Wake-up Indication | RC | 0h | Status is 1 after power-up if device is
woken-up remotely Status is cleared on read of this register |
| 8 | LPS Received Status | RC | 0h | Status is changed to 1 when LPS command
is received from link partner Status is cleared on read of this register |
| 7 | RESERVED | R | 0h | Reserved |
| 6 | No Link Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 5 | Sleep Fail Indication | R/W | 1h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 4 | Power-On Reset Done Indication | R/W | 1h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 3 | No Frame Indication | R/W | 0h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 2 | WUR Received Indication | R/W | 1h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
| 1 | RESERVED | R | 0h | Reserved |
| 0 | LPS Received Indication | R/W | 1h | 1b = Enable indication on INT_N pin if
corresponding Interrupt Status is set 0b = Indication is disabled |
REG_19 is shown in Figure 8-13 and described in Table 8-17.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | ||
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | PHY Address | ||||||
| R-0h | R-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-14 | RESERVED | R | 0h | Reserved |
| 13 | RESERVED | R | 0h | Reserved |
| 12 | RESERVED | R | 0h | Reserved |
| 11 | RESERVED | R | 0h | Reserved |
| 10 | RESERVED | R | 0h | Reserved |
| 9-5 | RESERVED | R | 0h | Reserved |
| 4-0 | PHY Address | R | 0h | PHY Address latched from straps |
REG_1A is shown in Figure 8-14 and described in Table 8-18.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Data Polarity Status | RESERVED | Jabber Detect Disable | ||||
| R-0h | R-0h | R-0h | R/W-0h | ||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-5 | RESERVED | R | 0h | Reserved |
| 4 | Data Polarity Status | R | 0h | 0b = Normal Polarity 1b = Reverse Polarity |
| 3-1 | RESERVED | R | 0h | Reserved |
| 0 | Jabber Detect Disable | R/W | 0h | 0b = Jabber detection is enabled 1b =Jabber detection is disabled |
TC10_ABORT_REG is shown in Figure 8-15 and described in Table 8-19.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Sleep Abort through GPIO | Sleep Abort | |||||
| R-0h | R/W-0h | R/W-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-2 | RESERVED | R | 0h | Reserved |
| 1 | Sleep Abort through GPIO | R/W | 0h | Sleep can be aborted by driving high on GPIO 1b = Use LED_1 for Sleep Abort 0b = GPIO is not used for Sleep Abort |
| 0 | Sleep Abort | R/W | 0h | This bit to be set 1 to abort the
sleep Cleared on transition to normal mode |
CDCR is shown in Figure 8-16 and described in Table 8-20.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| TDR Start | TDR Auto-Run Enable | RESERVED | |||||
| RH/W1S-0h | R/W-0h | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | TDR Done Status | TDR Fail status | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | TDR Start | RH/W1S | 0h | 1b = Start TDR Bit is cleared after TDR run is complete |
| 14 | TDR Auto-Run Enable | R/W | 0h | 1b = Start TDR automatically on link
down 0b = Start TDR manually using 0x1E[15] |
| 13-2 | RESERVED | R | 0h | Reserved |
| 1 | TDR Done Status | R | 0h | 1b = TDR done 0b = TDR on-going or not initiated |
| 0 | TDR Fail status | R | 0h | When TDR Done Status is 1, this bit
indicates if TDR ran successfully 1b = TDR run failed 0b = TDR ran successfully |
PHYRCR is shown in Figure 8-17 and described in Table 8-21.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Hard Reset | Soft Reset | RESERVED | RESERVED | ||||
| R-0/W1S-0h | R-0/W1S-0h | R-0h | R-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | RESERVED | ||||
| R-0h | R-0h | R-0h | R-0h | ||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Hard Reset | R-0/W1S | 0h | Resets Digital Core and Register
File This bet is self clearing |
| 14 | Soft Reset | R-0/W1S | 0h | Resets Digital Core but Register File
is not reset This bit is self clearing |
| 13 | RESERVED | R | 0h | Reserved |
| 12-8 | RESERVED | R | 0h | Reserved |
| 7 | RESERVED | R | 0h | Reserved |
| 6 | RESERVED | R | 0h | Reserved |
| 5 | RESERVED | R | 0h | Reserved |
| 4-0 | RESERVED | R | 0h | Reserved |
Register_133 is shown in Figure 8-18 and described in Table 8-22.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Link Up Status | PHY Control In Send Data Mode | Link Status | RESERVED | |||
| R-0h | R-0h | R-0h | R-0h | R-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | Descrambler Lock Status | Local Receiver Status | Remote Receiver Status |
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | Link Up Status | R | 0h | Link Up status as defined by CnS |
| 13 | PHY Control In Send Data Mode | R | 0h | PHY Control In Send Data Status |
| 12 | Link Status | R | 0h | Link Status set by Link Monitor |
| 11-8 | RESERVED | R | 0h | Reserved |
| 7 | RESERVED | R | 0h | Reserved |
| 6 | RESERVED | R | 0h | Reserved |
| 5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2 | Descrambler Lock Status | R | 0h | Descrambler lock status |
| 1 | Local Receiver Status | R | 0h | Local receiver status |
| 0 | Remote Receiver Status | R | 0h | Remote receiver status |
Register_134 is shown in Figure 8-19 and described in Table 8-23.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Bad SSD Count | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Bad SSD Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Bad SSD Count | R | 0h | Number of BAD SSD symbols received |
Register_135 is shown in Figure 8-20 and described in Table 8-24.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Bad ESD Count | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Bad ESD Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Bad ESD Count | R | 0h | Number of BAD ESD symbols received |
Register_17F is shown in Figure 8-21 and described in Table 8-25.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| WUR from WAKE pin | WUP Enable | RESERVED | |||||
| R/W-0h | R/W-1h | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Wake Pulse Threshold | |||||||
| R/W-28h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | WUR from WAKE pin | R/W | 0h | Enable WUR transmission when a pulse is
transmitted on WAKE pin 1b = Enable sending WUR Threshold of WAKE pulse width can be configured through 0x17F[7:0] |
| 14 | WUP Enable | R/W | 1h | Enable WUP transmission after local
wake 1b = WUP transmission is enabled 0b = WUP transmission is disabled This option can be effectively used when PHY powers-up in Standby mode through strap |
| 13-8 | RESERVED | R | 0h | Reserved |
| 7-0 | Wake Pulse Threshold | R/W | 28h | Width of WAKE pulse in microseconds required to initiate WUR during an active link |
Register_181 is shown in Figure 8-22 and described in Table 8-26.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RX LPS Count | ||||||
| R-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RX LPS Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-10 | RESERVED | R | 0h | Reserved |
| 9-0 | RX LPS Count | R | 0h | Indicates number of LPS codes received |
Register_182 is shown in Figure 8-23 and described in Table 8-27.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RX WUR Count | ||||||
| R-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RX WUR Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-10 | RESERVED | R | 0h | Reserved |
| 9-0 | RX WUR Count | R | 0h | Indicates number of WUR codes received |
LPS_CFG is shown in Figure 8-24 and described in Table 8-28.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | ||
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | Wake Forward Force | Wake Forward Pulse Width | Wake Forward Enable | RESERVED | |
| R-0h | R-0h | R-0h | R/W-0h | R/W-0h | R/W-1h | R-0h | |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14-13 | RESERVED | R | 0h | Reserved |
| 12 | RESERVED | R | 0h | Reserved |
| 11-10 | RESERVED | R | 0h | Reserved |
| 9 | RESERVED | R | 0h | Reserved |
| 8-7 | RESERVED | R | 0h | Reserved |
| 6 | RESERVED | R | 0h | Reserved |
| 5 | RESERVED | R | 0h | Reserved |
| 4 | Wake Forward Force | R/W | 0h | 1b = Force pulse on WAKE pin Pulse Width is confgurable by bits [3:2] The bit is self-cleared |
| 3-2 | Wake Forward Pulse Width | R/W | 0h | Configures the pulse width on WAKE pin
for wake-forwarding 00b = 50us 01b = 500us 10b = 2ms 11b = 20ms |
| 1 | Wake Forward Enable | R/W | 1h | Enable Wake Forwarding on WAKE pin on
reception of WUR Command 0b = Enable Wake forwarding 1b = Disable Wake forwarding |
| 0 | RESERVED | R | 0h | Reserved |
LPS_CFG2 is shown in Figure 8-25 and described in Table 8-29.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | Stop Sleep Negotiation on Link Down | Stop Sleep Negotiation on Activity | RESERVED | RESERVED | TC10 Disable |
| R-0h | R-0h | R-0h | R/W-1h | R/W-1h | R-0h | R-0h | R/W-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Autonomous Mode | Transition To Standby | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED |
| R-0h | R/W-1h | R/W-0h | R-0h | R-0h | R-0h | R-0h | R-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | RESERVED | R | 0h | Reserved |
| 13 | RESERVED | R | 0h | Reserved |
| 12 | Stop Sleep Negotiation on Link Down | R/W | 1h | 1b = Stop Sleep Negotiation if link goes down during negotiation |
| 11 | Stop Sleep Negotiation on Activity | R/W | 1h | 1b = Stop Sleep Negotiation when activity from MAC is observed in SLEEP_ACK state |
| 10 | RESERVED | R | 0h | Reserved |
| 9 | RESERVED | R | 0h | Reserved |
| 8 | TC10 Disable | R/W | 0h | 1b = Disable TC10 0b = Enable TC10 Default value is decided by RX_CLK strap |
| 7 | RESERVED | R | 0h | Reserved |
| 6 | Autonomous Mode | R/W | 1h | 1b = PHY entered normal mode on power
up 0b = PHY entered standby mode on power up Default value is decided by LED_1 strap This bit is cleared post link up. |
| 5 | Transition To Standby | R/W | 0h | 1b = Enable normal to standby
transition on over temperature/over voltage/under
voltage 0b = Disable normal to standby transition on over temperature/over voltage/under voltage |
| 4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2 | RESERVED | R | 0h | Reserved |
| 1 | RESERVED | R | 0h | Reserved |
| 0 | RESERVED | R | 0h | Reserved |
LPS_CFG3 is shown in Figure 8-26 and described in Table 8-30.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Power State Entry | ||||||
| R-0h | RH/W1S-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Power State Entry | |||||||
| RH/W1S-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-9 | RESERVED | R | 0h | Reserved |
| 8-0 | Power State Entry | RH/W1S | 0h | 00000001b = Normal command 00000010b = Sleep request 00010000b = Standby command 10000000b = WUR command |
LINK_FAIL_CNT is shown in Figure 8-27 and described in Table 8-31.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Link Losses Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | RESERVED | R | 0h | Reserved |
| 7-0 | Link Losses Count | R | 0h | TI Custom Link Loss Counter: Count incremented on fall edge of Link Status Count cleared on read of this register |
LPS_STATUS is shown in Figure 8-28 and described in Table 8-32.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Power State Status | ||||||
| R-0h | R-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-7 | RESERVED | R | 0h | Reserved |
| 6-0 | Power State Status | R | 0h | 00000001b = Sleep Mode 00000010b = Standby Mode 00000100b = Normal Mode 00001000b = Sleep Ack 00010000b = Sleep Req 00100000b = Sleep Fail 01000000b = Sleep Silent |
PCF is shown in Figure 8-29 and described in Table 8-33.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | PHY Control Frames Error Status | PHY Control Frames Ok Status | RESERVED | PHY Control Frames Destination Address | |||
| R-0h | R-0h | R-0h | R-0h | R/W-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PHY Control Frames Interrupt | PHY Control Frames Broadcast Disable | PHY Control Frames Buffer Size | PHY Control Frames Enable | ||||
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | ||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | PHY Control Frames Error Status | R | 0h | Indicates an error was detected in a PCF Frame since the last read of this register. This bit will be cleared on read. |
| 13 | PHY Control Frames Ok Status | R | 0h | Indicates a PCF Frame has completed without error since the last read of this register. This bit will be cleared on read. |
| 12-9 | RESERVED | R | 0h | Reserved |
| 8 | PHY Control Frames Destination Address | R/W | 0h | Select MAC Destination Address for Phy
Control Frames: 0: Use Mac Address [08 00 17 0B 6B 0F] 1: Use Mac Address [08 00 17 00 00 00] The device will also recognize packets with the above address with the Multicast bit set (i.e. 09 00 17) |
| 7-6 | PHY Control Frames Interrupt | R/W | 0h | PCF Interrupt Control and Status: Bit 7 - Enable indication of PCF Frame Error Status on INT_N pin Bit 6 - Enable indication of PCF Frame OK Status on INT_N pin Status is available in 0x1A0[14:13] |
| 5 | PHY Control Frames Broadcast Disable | R/W | 0h | By default, the device will accept broadcast Phy Control Frames which have a Phy address field of 0x1F. If this bit is set to a 1, the Phy Control Frame must have a Phy Address field that exactly matches the device Phy Address. |
| 4-1 | PHY Control Frames Buffer Size | R/W | 0h | Determines the buffer size for transmit to allow Phy Control Frame detection. All packets will be delayed as they pass through this buffer. If set to 0, packets will not be delayed and Phy Control frames will be truncated after the Destination Address field |
| 0 | PHY Control Frames Enable | R/W | 0h | Enables Register writes using Phy Control Frames |
MISC1 is shown in Figure 8-30 and described in Table 8-34.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Swap DA SA | RESERVED | RESERVED | RESERVED | |||
| R-0h | R/W-0h | R-0h | R-0h | R-0h | |||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-7 | RESERVED | R | 0h | Reserved |
| 6 | Swap DA SA | R/W | 0h | 1b = Swap Destination Address and Source Address fields of the packet for debug |
| 5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3-0 | RESERVED | R | 0h | Reserved |
PPM0 is shown in Figure 8-31 and described in Table 8-35.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Monitor Clock Count [15:0] | |||||||
| R/W-F423h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Monitor Clock Count [15:0] | |||||||
| R/W-F423h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Monitor Clock Count [15:0] | R/W | F423h | Lower 16 bits of Monitor clock counter
in PPM Monitor Monitor Clock Count = Refresh period/monitor clock period Refresh period can be any common multiple of monitor and reference clock periods |
PPM1 is shown in Figure 8-32 and described in Table 8-36.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Monitor Clock Count [31:16] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Monitor Clock Count [31:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Monitor Clock Count [31:16] | R/W | 0h | Higher 16 bits of Monitor clock counter
in PPM Monitor Monitor Clock Count = Refresh period/monitor clock period Refresh period can be any common multiple of monitor and reference clock periods |
PPM2 is shown in Figure 8-33 and described in Table 8-37.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Reference Clock Count [15:0] | |||||||
| R/W-30D3h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Reference Clock Count [15:0] | |||||||
| R/W-30D3h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Reference Clock Count [15:0] | R/W | 30D3h | Lower 16 bits of Reference clock
counter in PPM Monitor Reference Clock Count = Refresh period/reference clock period Refresh period can be any common multiple of monitor and reference clock periods |
PPM3 is shown in Figure 8-34 and described in Table 8-38.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Reference Clock Count [31:16] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Reference Clock Count [31:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Reference Clock Count [31:16] | R/W | 0h | Higher 16 bits of Reference clock
counter in PPM Monitor Reference Clock Count = Refresh period/reference clock period Refresh period can be any common multiple of monitor and reference clock periods |
PPM4 is shown in Figure 8-35 and described in Table 8-39.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PPM Monitor Interrupt Threshold Count - 1 [15:0] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PPM Monitor Interrupt Threshold Count - 1 [15:0] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PPM Monitor Interrupt Threshold Count - 1 [15:0] | R/W | 0h | Lower 16 bits of PPM Monitor Interrupt
Threshold Count - 1: PPM Monitor Interrupt Threshold Count -1 = Monitor Clock Count * PPM beyond which interrupt should be flagged |
PPM5 is shown in Figure 8-36 and described in Table 8-40.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PPM Monitor Interrupt Threshold Count - 1 [31:16] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PPM Monitor Interrupt Threshold Count - 1 [31:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PPM Monitor Interrupt Threshold Count - 1 [31:16] | R/W | 0h | Higher 16 bits of PPM Monitor Interrupt
Threshold Count -1: PPM Monitor Interrupt Threshold Count -1 = Monitor Clock Count * PPM beyond which interrupt should be flagged |
PPM6 is shown in Figure 8-37 and described in Table 8-41.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PPM Monitor Interrupt Threshold Count - 2 [15:0] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PPM Monitor Interrupt Threshold Count - 2 [15:0] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PPM Monitor Interrupt Threshold Count - 2 [15:0] | R/W | 0h | Lower 16 bits of PPM Monitor Interrupt
Threshold Count - 2: PPM Monitor Interrupt Threshold Count -2 = Monitor Clock Count |
PPM7 is shown in Figure 8-38 and described in Table 8-42.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PPM Monitor Interrupt Threshold Count - 2 [31:16] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PPM Monitor Interrupt Threshold Count - 2 [31:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PPM Monitor Interrupt Threshold Count - 2 [31:16] | R/W | 0h | Higher 16 bits of PPM Monitor Interrupt
Threshold Count -2: PPM Monitor Interrupt Threshold Count -2 = Monitor Clock Count |
PPM10 is shown in Figure 8-39 and described in Table 8-43.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PPM Monitor Output [15:0] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PPM Monitor Output [15:0] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PPM Monitor Output [15:0] | R/W | 0h | PPM Monitor output If 0x01AE[15] = 0, ppm offset is negative, if 0x01AE[15] = 1, ppm offset is positive PPM offset of monitor clock = {0x01AE[14:0],0x01AD[15:0]}/ {0x01A4, 0x01A3} |
PPM11 is shown in Figure 8-40 and described in Table 8-44.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PPM Monitor Output [31:16] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PPM Monitor Output [31:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PPM Monitor Output [31:16] | R/W | 0h | PPM Monitor output If 0x01AE[15] = 0, ppm offset is negative, if 0x01AE[15] = 1, ppm offset is positive PPM offset of monitor clock = {0x01AE[14:0],0x01AD[15:0]}/ {0x01A4, 0x01A3} |
PPM12 is shown in Figure 8-41 and described in Table 8-45.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PPM Monitor External Clock Select | PPM Monitor Enable | Reference Clock Select for PPM Monitor | Monitor Clock Select for PPM Monitor | ||||
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Monitor Clock Select for PPM Monitor | RESERVED | RESERVED | |||||
| R/W-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-14 | RESERVED | R/W | 0h | Reserved |
| 13 | PPM Monitor Enable | R/W | 0h | Enable for PPM monitor:
|
| 12-9 | Reference Clock Select for PPM Monitor | R/W | 0h | Selects the reference clock for the PPM
monitor
|
| 8-5 | Monitor Clock Select for PPM Monitor | R/W | 0h | Selects the monitor clock for the PPM
monitor
|
| 4-2 | RESERVED | R | 0h | Reserved |
| 1-0 | RESERVED | R | 0h | Reserved |
fwu_reg_3 is shown in Figure 8-42 and described in Table 8-46.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | Fast Wake-Up Memory Load Enable | Fast Wake-Up Load Trigger | Fast Wake-Up Memory Reset | |||
| R-0h | R-0h | R/W-0h | R/W-0h | R/W-1h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | ||||||
| R-0h | R-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-12 | RESERVED | R | 0h | Reserved |
| 11 | RESERVED | R | 0h | Reserved |
| 10 | Fast Wake-Up Memory Load Enable | R/W | 0h | Program this bit to 1 to enable loading register address and data into the memory |
| 9 | Fast Wake-Up Load Trigger | R/W | 0h | Program this bit to 1 after programming
Register Address and Data in 0x1BC and 0x1BD This bit is auto-clearing |
| 8 | Fast Wake-Up Memory Reset | R/W | 1h |
|
| 7-2 | RESERVED | R | 0h | Reserved |
| 1-0 | RESERVED | R | 0h | Reserved |
spare_reg_tc10 is shown in Figure 8-43 and described in Table 8-47.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Configure Fast Wake-Up | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Configure Fast Wake-Up | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Configure Fast Wake-Up | R/W | 0h | To enable fast wake-up Memory
program 0x01D2 = 0x0004 0x01D2 = 0x0014 0x01D2 = 0x0004 |
TDR_CFG5 is shown in Figure 8-44 and described in Table 8-48.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | TDR Half Open Detect Enable | RESERVED | |||||
| R-0h | R/W-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-5 | RESERVED | R | 0h | Reserved |
| 4 | TDR Half Open Detect Enable | R/W | 0h | 1b = Enbales half open detection 0b = Disables half open detection |
| 3-0 | RESERVED | R | 0h | Reserved |
TDR_TC1 is shown in Figure 8-45 and described in Table 8-49.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Half Open Detect Status | ||||||
| R-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Fault Detect Status | Fault Type | TDR Fault Location | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-9 | RESERVED | R | 0h | Reserved |
| 8 | Half Open Detect Status | R | 0h | 1b = Half wire open detected 0b = Half wire open not detected |
| 7 | Fault Detect Status | R | 0h | 1b = Fault detected in cable 0b = No Fault detected in cable |
| 6 | Fault Type | R | 0h | 0b = Short to GND, supply, or between
MDI pins 1b = Open. Applicable to both 1-wire and 2-wire open faults |
| 5-0 | TDR Fault Location | R | 0h | Fault location in meters (Valid only if Fault Detect Status = 1) |
ANA_LD_CTRL_3 is shown in Figure 8-46 and described in Table 8-50.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| VDDIO Supply Level | RESERVED | RESERVED | RESERVED | RESERVED | |||
| R-0h | R-0h | R-0h | R-0h | R-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-14 | VDDIO Supply Level | R | 0h | VDDIO Level Detected by the PHY: 00b = 1.8V VDDIO 01b = 2.5V VDDIO 11b = 3.3V VDDIO |
| 13 | RESERVED | R | 0h | Reserved |
| 12 | RESERVED | R | 0h | Reserved |
| 11-10 | RESERVED | R | 0h | Reserved |
| 9-8 | RESERVED | R | 0h | Reserved |
| 7-4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2-0 | RESERVED | R | 0h | Reserved |
A2D_REG_48 is shown in Figure 8-47 and described in Table 8-51.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RGMII TX Shift Delay | |||||
| R-0h | R-0h | R/W-7h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RGMII RX Shift Delay | RESERVED | ||||||
| R/W-7h | R-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-13 | RESERVED | R | 0h | Reserved |
| 12 | RESERVED | R | 0h | Reserved |
| 11-8 | RGMII TX Shift Delay | R/W | 7h | Controls Internal Delay in RGMII mode
in Steps of 312.5ps Delay = ((Bit[7:4] in decimal) + 1)*312.5ps |
| 7-4 | RGMII RX Shift Delay | R/W | 7h | Controls Internal Delay in RGMII mode
in Steps of 312.5ps Delay = ((Bit[7:4] in decimal) + 1)*312.5ps |
| 3-0 | RESERVED | R | 0h | Reserved |
A2D_REG_64 is shown in Figure 8-48 and described in Table 8-52.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | ||||||
| R-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | ESD Event Counter Disable | ||
| R-0h | R-0h | R-0h | R-0h | R-0h | R/W-1h | ||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14-5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2 | RESERVED | R | 0h | Reserved |
| 1 | RESERVED | R | 0h | Reserved |
| 0 | ESD Event Counter Disable | R/W | 1h | 1b = Disable ESD Counter 0b = Enable ESD Counter This bit should be toggled to clear the ESD counter |
A2D_REG_66 is shown in Figure 8-49 and described in Table 8-53.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | ESD Event Count | RESERVED | |||||
| R-0h | R-0h | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14-9 | ESD Event Count | R | 0h | Field gives the number of ESD events on the copper channel |
| 8 | RESERVED | R | 0h | Reserved |
| 7-5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3-0 | RESERVED | R | 0h | Reserved |
A2D_REG_68 is shown in Figure 8-50 and described in Table 8-54.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Sleep Force Value | Sleep Force Enable | WAKE pin Force Value | WAKE pin Force Enable | |||
| R-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | |||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-4 | RESERVED | R | 0h | Reserved |
| 3 | Sleep Force Value | R/W | 0h | 1b = Force Sleep when Sleep Force Enable is set to 1 |
| 2 | Sleep Force Enable | R/W | 0h | 1b = Sleep Force Enable (Sleep Force Value has to be set) |
| 1 | WAKE pin Force Value | R/W | 0h | Force value on WAKE pin when WAKE pin
Force Enable is set 1b = High 0b = Low |
| 0 | WAKE pin Force Enable | R/W | 0h | 1b = Enable Force control of WAKE pin |
LEDS_CFG_1 is shown in Figure 8-51 and described in Table 8-55.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Disable LED Stretching | LED Blink Rate | RESERVED | ||||
| R-0h | R/W-0h | R/W-2h | R/W-6h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| LED_1 Options | RESERVED | ||||||
| R/W-1h | R/W-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | Disable LED Stretching | R/W | 0h | 0b = LED pulses are stretched according
to the blink rate in 'LED Blink Rate' field 1b = LED pulses are directly connected to RX_DV(for RX activity) and TX_CTRL(for TX Activity) |
| 13-12 | LED Blink Rate | R/W | 2h | Blink Rate of the LED when configured
for activity 00b = 20Hz (50ms) 01b = 10Hz (100ms) 10b = 5Hz (200ms) 11b = 2Hz (500ms) |
| 11-8 | RESERVED | R/W | 6h | Reserved |
| 7-4 | LED_1 Options | R/W | 1h | 0x0 : link OK 0x1 : link OK + blink on TX/RX activity 0x2 : link OK + blink on TX activity 0x3 : link OK + blink on RX activity 0x4 : link OK + 100Base-T1 Leader 0x5 : link OK + 100Base-T1 Follower 0x6 : TX/RX activity with stretch option 0x7 : Reserved 0x8 : Reserved 0x9 : Link lost (remains on until register 0x1 is read) 0xB : xMII TX/RX Error with stretch option |
| 3-0 | RESERVED | R/W | 0h | Reserved |
LEDS_CFG_2 is shown in Figure 8-52 and described in Table 8-56.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | |||
| R-0h | R-0h | R-0h | R-0h | R/W-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | LED_1 Force Enable | LED_1 Force Value | LED_1 Polarity | RESERVED | RESERVED | RESERVED |
| R/W-0h | R/W-1h | R/W-0h | R/W-0h | R/W-1h | R/W-0h | R/W-0h | R/W-1h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | RESERVED | R | 0h | Reserved |
| 13 | RESERVED | R | 0h | Reserved |
| 12-9 | RESERVED | R | 0h | Reserved |
| 8 | RESERVED | R/W | 0h | Reserved |
| 7 | RESERVED | R/W | 0h | Reserved |
| 6 | RESERVED | R/W | 1h | Reserved |
| 5 | LED_1 Force Enable | R/W | 0h | 1b = Force 'LED_1 Force Value' on LED_1 pin |
| 4 | LED_1 Force Value | R/W | 0h | When LED_1 Force Enable is set, this
bit decides the output of LED_1 0b = Low 1b = High |
| 3 | LED_1 Polarity | R/W | 1h | Polarity of LED_1: 0b = Active Low polarity 1b = Active High polarity Default value is decided by the strap on LED_1. If the strap is placed to supply, LED_1 polarity is 0, else LED_1 polarity is 1. |
| 2 | RESERVED | R/W | 0h | Reserved |
| 1 | RESERVED | R/W | 0h | Reserved |
| 0 | RESERVED | R/W | 1h | Reserved |
IO_MUX_CFG_1 is shown in Figure 8-53 and described in Table 8-57.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | LED_1 Confguration | ||||
| R-0h | R-0h | R-0h | R/W-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | RESERVED | ||||
| R-0h | R-0h | R-0h | R/W-0h | ||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14-12 | RESERVED | R | 0h | Reserved |
| 11 | RESERVED | R | 0h | Reserved |
| 10-8 | LED_1 Configuration | R/W | 0h | 000b = (default: LINK) 010b = WoL 011b = Under-Voltage indication 110b = ESD 111b = interrupt |
| 7 | RESERVED | R | 0h | Reserved |
| 6-4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2-0 | RESERVED | R/W | 0h | Reserved |
IO_MUX_CFG_2 is shown in Figure 8-54 and described in Table 8-58.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Enable TX_ER on LED_1 | RESERVED | RESERVED | |||||
| R/W-0h | R-0h | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | CLKOUT Configuration | |||||
| R-0h | R-0h | R/W-1h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Enable TX_ER on LED_1 | R/W | 0h | Configures LED_1 pin to TX_ER |
| 14-9 | RESERVED | R | 0h | Reserved |
| 8 | RESERVED | R | 0h | Reserved |
| 7-4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2-0 | CLKOUT Configuration | R/W | 1h | 000b = (default: LINK) 010b = WoL 011b = Under-Voltage indication 110b = ESD 111b = interrupt |
IO_MUX_CFG is shown in Figure 8-55 and described in Table 8-59.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | RESERVED | Impedance Control - RX pins | |||
| R-0h | R-0h | R-0h | R-0h | R/W-1h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Impedance Control - RX pins | Impedance Control - TX_CLK | ||||||
| R/W-1h | R/W-1h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-14 | RESERVED | R | 0h | Reserved |
| 13 | RESERVED | R | 0h | Reserved |
| 12-11 | RESERVED | R | 0h | Reserved |
| 10 | RESERVED | R | 0h | Reserved |
| 9-5 | Impedance Control - RX pins | R/W | 1h | Impedance control for RX_CLK,
RX_D[3:0], RX_CTRL, RX_ER 1h = Slew Mode -1 2h = Slew Mode -2 3h = Slew Mode -3 4h = Slew Mode -4 5h = Slew Mode -5 6h = Slew Mode -6 7h = Slew Mode -7 |
| 4-0 | Impedance Control - TX_CLK | R/W | 1h | 1h = Slew Mode -1 2h = Slew Mode -2 3h = Slew Mode -3 4h = Slew Mode -4 5h = Slew Mode -5 6h = Slew Mode -6 7h = Slew Mode -7 |
CHIP_SOR_1 is shown in Figure 8-56 and described in Table 8-60.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | LED_1 Strap | RX_D3 Strap | RESERVED | RESERVED | RESERVED | RXD3 Strap |
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RXD2 Strap | RXD1 Strap | RXD0 Strap | RXCLK Strap | RXER Strap | RXDV Strap | ||
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | ||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | RESERVED | R | 0h | Reserved |
| 13 | LED_1 Strap | R | 0h | LED_1 strap sampled at power up |
| 12 | RX_D3 Strap | R | 0h | RX_D3 strap sampled at power up |
| 11 | RESERVED | R | 0h | Reserved |
| 10 | RESERVED | R | 0h | Reserved |
| 9 | RESERVED | R | 0h | Reserved |
| 8 | RXD3 Strap | R | 0h | RX_D3 strap sampled at reset |
| 7 | RXD2 Strap | R | 0h | RX_D2 strap sampled at power up or reset |
| 6 | RXD1 Strap | R | 0h | RX_D1 strap sampled at power up or reset |
| 5 | RXD0 Strap | R | 0h | RX_D0 strap sampled at power up or reset |
| 4 | RXCLK Strap | R | 0h | RX_CLK strap sampled at power up or reset |
| 3-2 | RXER Strap | R | 0h | RX_ER strap sampled at power up or reset |
| 1-0 | RXDV Strap | R | 0h | RX_DV strap sampled at power up or reset |
LED1_CLKOUT_ANA_CTRL is shown in Figure 8-57 and described in Table 8-61.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | |||||
| R-0h | R-0h | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | LED_1 Mux Control | CLKOUT Mux Control | ||||
| R-0h | R-0h | R/W-3h | R/W-0h | ||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | RESERVED | R | 0h | Reserved |
| 13-5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3-2 | RESERVED | R/W | 3h |
Reserved |
| 1-0 |
CLKOUT Mux Control | R/W | 0h |
00b = 25MHz XI Clock for daisy chaining |
IMPEDANCE_CTRL_0 is shown in Figure 8-58 and described in Table 8-62.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Impedance Control - CLKOUT | ||||||
| R-0h | R/W-1h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Impedance Control - LED_1 | ||||||
| R-0h | R/W-1h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-13 | RESERVED | R | 0h | Reserved |
| 12-8 | Impedance Control - CLKOUT | R/W | 1h | 1h = Slew Mode -1 2h = Slew Mode -2 3h = Slew Mode -3 4h = Slew Mode -4 5h = Slew Mode -5 6h = Slew Mode -6 7h = Slew Mode -7 |
| 7-5 | RESERVED | R | 0h | Reserved |
| 4-0 | Impedance Control - LED_1 | R/W | 1h | 1h = Slew Mode -1 2h = Slew Mode -2 3h = Slew Mode -3 4h = Slew Mode -4 5h = Slew Mode -5 6h = Slew Mode -6 7h = Slew Mode -7 |
LINKUP_TIMER_1 is shown in Figure 8-59 and described in Table 8-63.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Link Up Timer [15:0] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Link Up Timer [15:0] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Link Up Timer [15:0] | R | 0h | Link Up timer calculated from Power-up
or Soft Reset or Link Down whichever comes later Link Up time (in ns) = Link Up Timer [31:0]*40 |
LINKUP_TIMER_2 is shown in Figure 8-60 and described in Table 8-64.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Link Up Timer [31:16] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Link Up Timer [31:16] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Link Up Timer [31:16] | R | 0h | Link Up timer calculated from Power-up
or Soft Reset or Link Down whichever comes later Link Up time (in ns) = Link Up Timer [31:0]*40 |
TX_PR_FILT_CTRL is shown in Figure 8-61 and described in Table 8-65.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | MDI Polarity Invert | MDI Transmit Disable | ||||
| R-0h | R-0h | R/W-0h | R/W-0h | ||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-3 | RESERVED | R | 0h | Reserved |
| 2 | RESERVED | R | 0h | Reserved |
| 1 | MDI Polarity Invert | R/W | 0h | 1b = Invert polarity on MDI transmit side |
| 0 | MDI Transmit Disable | R/W | 0h | 1b = Disable Transmit on MDI 0b = Enable Transmit on MDI |
PG_REG_1 is shown in Figure 8-62 and described in Table 8-66.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RMII CRS_DV Config | RESERVED | |||||
| R-0h | R/W-1h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-5 | RESERVED | R | 0h | Reserved |
| 4 | RMII CRS_DV Config | R/W | 1h | Configure Pin 15 as RX_DV or CRS_DV:
1b = Pin15 is CRS_DV 0b = Pin 15 is RX_DV |
| 3-0 | RESERVED | R | 0h | Reserved |
PG_REG_4 is shown in Figure 8-63 and described in Table 8-67.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Force Receive Polarity Force Enable | Receive Polairty Force Value | RESERVED | ||||
| R-0h | R/W-0h | R/W-0h | R-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-14 | RESERVED | R | 0h | Reserved |
| 13 | Force Receive Polarity Force Enable | R/W | 0h | 0x0553[13:12] = 2'b10 : Disable
Auto-Polarity Correction and force no polairty
inversion 0x0553[13:12] = 2'b11 : Disable Auto-Polarity Correction and force polairty inversion |
| 12 | Receive Polairty Force Value | R/W | 0h | 0x0553[13:12] = 2'b10 : Disable
Auto-Polarity Correction and force no polairty
inversion 0x0553[13:12] = 2'b11 : Disable Auto-Polarity Correction and force polairty inversion |
| 11-0 | RESERVED | R | 0h | Reserved |
TC1_LINK_FAIL_LOSS is shown in Figure 8-64 and described in Table 8-68.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Link Losses | Link Failures | ||||||
| R-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Link Failures | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-10 | Link Losses | R | 0h | Number of Link Losses as defined in TC1 since last power cycle |
| 9-0 | Link Failures | R | 0h | Link Failures as defined in TC1 Number of Link Failures (including RX errors, Bad SSD, Bad ESD, Bad SQI) not causing a link down |
TC1_LINK_TRAINING_TIME is shown in Figure 8-65 and described in Table 8-69.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Communication Ready | RESERVED | ||||||
| R-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Link Training Time | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Communication Ready | R | 0h | Communication ready as defined in
TC1 1b = PHY is ready for communication |
| 14-8 | RESERVED | R | 0h | Reserved |
| 7-0 | Link Training Time | R | 0h | Link Training Time measured in milliseconds measured from soft reset |
NO_LINK_TH is shown in Figure 8-66 and described in Table 8-70.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| No Link Timer Threshold | |||||||
| R/W-96h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | RESERVED | R | 0h | Reserved |
| 7-0 | No Link Timer Threshold | R/W | 96h | Time Threshold in milliseconds for No Link Interrupt |
DITH_CTRL_0 is shown in Figure 8-67 and described in Table 8-71.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | Dithering Direction |
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R/W-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | ||||||
| R-0h | R-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | RESERVED | R | 0h | Reserved |
| 13 | RESERVED | R | 0h | Reserved |
| 12 | RESERVED | R | 0h | Reserved |
| 11 | RESERVED | R | 0h | Reserved |
| 10 | RESERVED | R | 0h | Reserved |
| 9 | RESERVED | R | 0h | Reserved |
| 8 | Dithering Direction | R/W | 0h | Selects type of Sawtooth profile
|
| 7-4 | RESERVED | R | 0h | Reserved |
| 3-0 | RESERVED | R | 0h | Reserved |
DITH_CTRL_1 is shown in Figure 8-68 and described in Table 8-72.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Dithering Frequency Step | |||||||
| R/W-64h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Dithering Modulation Period | |||||||
| R/W-Dh | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | Dithering Frequency Step | R/W | 64h | Configure the maximum frequency offset
for dithering 0x05A1[15:8] = (Required (delta(f)/f) *217)/(0x5A1[7:0]) Default delta(f)/f = 1% delta(f)/f should be limitied to ≤ 2% |
| 7-0 | Dithering Modulation Period | R/W | Dh | Configures the modulation period for
dithering 0x5A1[7:0] = Dithering Modulation Period / 640ns) Default Modulation Period = 13*640ns = 8.34 us |
DITH_RFI_EN_CTRL is shown in Figure 8-69 and described in Table 8-73.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Dithering Profile | RESERVED | Dithering Enable | MAC Interface Dithering Enable | Core Clocks Dithering Enable | RESERVED | ||
| R/W-0h | R-0h | R/W-1h | R/W-1h | R/W-0h | R-0h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-14 | Dithering Profile | R/W | 0h | Select Dithering Frequency Profile
|
| 13 | RESERVED | R | 0h | Reserved |
| 12 | Dithering Enable | R/W | 1h | 1b = Enable Clock Dithering Engine |
| 11 | MAC Interface Dithering Enable | R/W | 1h | 1b = Enable dithering of RMII, RGMII, MII MAC Interface Outputs |
| 10 | Core Clocks Dithering Enable | R/W | 0h | 1b = Enable dithering for Internal Digital clocks |
| 9-0 | RESERVED | R | 0h | Reserved |
RGMII_CTRL is shown in Figure 8-70 and described in Table 8-74.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RGMII TX FIFO Half Full Threshold | RGMII Enable | Invert RGMII TX Data Lines | Invert RGMII RX Data Lines | RESERVED | ||
| R-0h | R/W-2h | R/W-Xh | R/W-0h | R/W-0h | R-0h | ||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-7 | RESERVED | R | 0h | Reserved |
| 6-4 | RGMII TX FIFO Half Full Threshold | R/W | 2h | RGMII TX sync FIFO half full threshold |
| 3 | RGMII Enable | R/W | 0h | 1b = RGMII enable 0b = RGMII disable Default value is latched from straps |
| 2 | Invert RGMII TX Data Lines | R/W | 0h | 1b = Invert RGMII TXD[3:0] TX_D3 to TX_D0 TX_D2 to TX_D1 TX_D1 to TX_D2 TX_D0 to TX_D3 |
| 1 | Invert RGMII RX Data Lines | R/W | 0h | 1b = Invert RGMII RXD[3:0] RX_D3 to RX_D0 RX_D2 to RX_D1 RX_D1 to RX_D2 RX_D0 to RX_D3 |
| 0 | RESERVED | R | 0h | Reserved |
RGMII_FIFO_STATUS is shown in Figure 8-71 and described in Table 8-75.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RGMII TX FIFO Full Error | RGMII TX FIFO Empty Error | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-2 | RESERVED | R | 0h | Reserved |
| 1 | RGMII TX FIFO Full Error | R | 0h | 1b = RGMII TX full error has been
indicated 0b = No empty fifo error This bit is only cleared on device reset |
| 0 | RGMII TX FIFO Empty Error | R | 0h | 1b = RGMII TX empty error has been
indicated 0b = No empty fifo error This bit is only cleared on device reset |
RGMII_CLK_SHIFT_CTRL is shown in Figure 8-72 and described in Table 8-76.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RGMII RX Shift | RGMII TX Shift | |||||
| R-0h | R/W-Xh | R/W-Xh | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-2 | RESERVED | R | 0h | Reserved |
| 1 | RGMII RX Shift | R/W | 0h | 0b = clock and data are aligned 1b = clock is internally delayed by value programmed in DLL RX Shift Delay |
| 0 | RGMII TX Shift | R/W | 0h | 0b = clock and data are aligned 1b = clock is internally delayed by value programmed in DLL TX Shift Delay |
SGMII_CTRL_1 is shown in Figure 8-73 and described in Table 8-77.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| SGMII TX Error Disable | RESERVED | RESERVED | SGMII Enable | SGMII TX Polairty Invert | |||
| R/W-0h | R-0h | R-0h | R/W-Xh | R/W-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| SGMII TX Polairty Invert | RESERVED | RESERVED | RESERVED | RESERVED | SGMII Auto Negotiation Enable | ||
| R/W-0h | R-0h | R-0h | R-0h | R-0h | R/W-1h | ||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | SGMII TX Error Disable | R/W | 0h | 1b = Disable SGMII TX Error
indication 0b = Enable SGMII TX Error indication |
| 14 | RESERVED | R | 0h | Reserved |
| 13-10 | RESERVED | R | 0h | Reserved |
| 9 | SGMII Enable | R/W | 0h | 1b = SGMII enable 0b = SGMII disable Default value is latched from straps If both SGMII and RGMII are enabled, SGMII take precedence |
| 8 | SGMII TX Polairty Invert | R/W | 0h | 1b = Invert SGMII RX_D[3:2] polarity |
| 7 | SGMII TX Polairty Invert | R/W | 0h | 1b = Invert SGMII TX_D[1:0] polarity |
| 6-5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2-1 | RESERVED | R | 0h | Reserved |
| 0 | SGMII Auto Negotiation Enable | R/W | 1h | 1b = Enable SGMII Auto-Negotaition 0b = Disable SGMII Auto-Negotiation |
SGMII_STATUS is shown in Figure 8-74 and described in Table 8-78.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | SGMII Page Received | SGMII Link Status | SGMII Auto Negotiation Status | Word Boundary Align Indication | Word Boundary Sync Status | ||
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | ||||||
| R-0h | R-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-13 | RESERVED | R | 0h | Reserved |
| 12 | SGMII Page Received | R | 0h | 1b = A new auto neg page received 0b = No new auto neg page received |
| 11 | SGMII Link Status | R | 0h | 1b = SGMII link up 0b = SGMII link down |
| 10 | SGMII Auto Negotiation Status | R | 0h | 1b = SGMII autoneg completed |
| 9 | Word Boundary Align Indication | R | 0h | 1b = Aligned |
| 8 | Word Boundary Sync Status | R | 0h | 1b = sync achieved 0b = sync not achieved |
| 7-4 | RESERVED | R | 0h | Reserved |
| 3-0 | RESERVED | R | 0h | Reserved |
SGMII_CTRL_2 is shown in Figure 8-75 and described in Table 8-79.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | ||||||
| R-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | SGMII TX FIFO Half Full Threshold | SGMII RX FIFO Half Full Threshold | ||||
| R-0h | R-0h | R/W-4h | R/W-4h | ||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-9 | RESERVED | R | 0h | Reserved |
| 8 | RESERVED | R | 0h | Reserved |
| 7 | RESERVED | R | 0h | Reserved |
| 6 | RESERVED | R | 0h | Reserved |
| 5-3 | SGMII TX FIFO Half Full Threshold | R/W | 4h | SGMII TX sync FIFO half full threshold |
| 2-0 | SGMII RX FIFO Half Full Threshold | R/W | 4h | SGMII RX sync FIFO half full threshold |
SGMII_FIFO_STATUS is shown in Figure 8-76 and described in Table 8-80.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | SGMII RX FIFO Full Error | SGMII RX FIFO Empty Error | SGMII TX FIFO Full Error | SGMII TX FIFO Empty Error | |||
| R-0h | RC-0h | RC-0h | RC-0h | RC-0h | |||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-4 | RESERVED | R | 0h | Reserved |
| 3 | SGMII RX FIFO Full Error | RC | 0h | 1b = SGMII RX fifo full error has been
indicated 0b = No error indication |
| 2 | SGMII RX FIFO Empty Error | RC | 0h | 1b = SGMII RX fifo empty error has been
indicated 0b = No error indication |
| 1 | SGMII TX FIFO Full Error | RC | 0h | 1b = SGMII TX fifo full error has been
indicated 0b = No error indication |
| 0 | SGMII TX FIFO Empty Error | RC | 0h | 1b = SGMII TX fifo empty error has been
indicated 0b = No error indication |
PRBS_STATUS_1 is shown in Figure 8-77 and described in Table 8-81.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PRBS Error Overflow Counter | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | RESERVED | R | 0h | Reserved |
| 7-0 | PRBS Error Overflow Counter | R | 0h | Holds number of error counter overflow
that received by the PRBS checker. Value in this register is locked when write is done to register prbs_status_6 bit[0] or bit[1]. Counter stops on 0xFF. Note: when PRBS counters work in single mode, overflow counter is not active |
PRBS_CTRL_1 is shown in Figure 8-78 and described in Table 8-82.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | Send Packet | RESERVED | PRBS Check Select | |||
| R-0h | R-0h | R-0/W1S-0h | R-0h | R/W-5h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | PRBS Transmit Select | PRBS Count Mode | PRBS Checker Enable | PRBS Generation Enable | PRBS or Packet Generation Enable | ||
| R-0h | R/W-7h | R/W-0h | R/W-1h | R/W-0h | R/W-0h | ||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-14 | RESERVED | R | 0h | Reserved |
| 13 | RESERVED | R | 0h | Reserved |
| 12 | Send Packet | R-0/W1S | 0h | Enables generating MAC packet with
fix/incremental data with CRC (0x619[0] has to be set and 0x619[1] has to be clear) Cleared automatically when pkt_done is set 1b = Transmit MAC packet with CRC 0b = Stop MAC packet |
| 11 | RESERVED | R | 0h | Reserved |
| 10-8 | PRBS Check Select | R/W | 5h | Selects the direction of PRBS checker
reception 000b = Checker receives from RGMII TX 001b = Checker receives SGMII TX 101b = Checker receives from MDI RX |
| 7 | RESERVED | R | 0h | Reserved |
| 6-4 | PRBS Transmit Select | R/W | 7h | Selects the direction of PRBS
transmission 000b = PRBS transmits to RGMII RX 001b = PRBS transmits to SGMII RX 101b = PRBS transmits to MDI TX |
| 3 | PRBS Count Mode | R/W | 0h | 1b = Continuous mode, when one of the
PRBS counters reaches max value, pulse is generated
and counter starts counting from zero again 0b = Single mode, When one of the PRBS counters reaches max value, PRBS checker stops counting. |
| 2 | PRBS Checker Enable | R/W | 1h | Enable PRBS checker (to receive
data) To be enabled for counters in 0x63C, 0x63D, 0x63E to work 1b = Enable PRBS checker |
| 1 | PRBS Generation Enable | R/W | 0h | If 0x619[0] is set, 1b = Transmits PRBS packet 0b = Transmits non-PRBS packet (PRBS checker is also disabled in this case) |
| 0 | PRBS or Packet Generation Enable | R/W | 0h | 1b = Enable packet/PRBS generator 0b = Disable packet/PRBS generator |
PRBS_CTRL_2 is shown in Figure 8-79 and described in Table 8-83.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Packet Length | |||||||
| R/W-5DCh | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Packet Length | |||||||
| R/W-5DCh | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Packet Length | R/W | 5DCh | Sets packet length (in bytes) between the PRBS packets or non-PRBS packets generated |
PRBS_CTRL_3 is shown in Figure 8-80 and described in Table 8-84.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PRBS IPG | |||||||
| R/W-7Dh | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | RESERVED | R | 0h | Reserved |
| 7-0 | PRBS IPG | R/W | 7Dh | Sets IPG (in bytes) between the PRBS packets or non-PRBS packets generated |
PRBS_STATUS_2 is shown in Figure 8-81 and described in Table 8-85.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PRBS Checker Byte Count | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PRBS Checker Byte Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PRBS Checker Byte Count | R | 0h | Holds number of total bytes that
received by the PRBS checker Value in register is locked when 0x620[0] or 0x620[1] are written When PRBS Count Mode set to zero, count stops on 0xFFFF This counter is cleared if this counter is read after programming 0x620[1]=1 |
PRBS_STATUS_3 is shown in Figure 8-82 and described in Table 8-86.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PRBS Checker Packet Count-1 | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PRBS Checker Packet Count-1 | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PRBS Checker Packet Count-1 | R | 0h | Holds Bits [15:0] of number of total
packets received by the PRBS checker Value in register is locked when 0x620[0] or 0x620[1] are written When PRBS Count Mode set to zero, count stops on 0xFFFFFFFF This counter is cleared if 0x61D,0x61E are read in the same order, after programming 0x620[1]=1 |
PRBS_STATUS_4 is shown in Figure 8-83 and described in Table 8-87.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PRBS Checker Packet Count-2 | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PRBS Checker Packet Count-2 | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PRBS Checker Packet Count-2 | R | 0h | Holds Bits [31:16] of number of total
packets received by the PRBS checker Value in register is locked when 0x620[0] or 0x620[1] are written When PRBS Count Mode set to zero, count stops on 0xFFFFFFFF This counter is cleared if 0x61D,0x61E are read in the same order, after programming 0x620[1]=1 |
PRBS_STATUS_5 is shown in Figure 8-84 and described in Table 8-88.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | MAC Packet Gen Done | MAC Packet Gen Busy | PRBS Checker Packet Count Overflow Status | PRBS Checker Byte Count Overflow Status | PRBS Lock | ||
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PRBS Error Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-13 | RESERVED | R | 0h | Reserved |
| 12 | MAC Packet Gen Done | R | 0h | Set when all MAC packets with CRC are
transmitted 1b = MAC packets transmission completed 0b = MAC packet transmission in progress |
| 11 | MAC Packet Gen Busy | R | 0h | 1b = Packet generator is in process 0b = Packet generator is not in process |
| 10 | PRBS Checker Packet Count Overflow Status | R | 0h | If PRBS Checker Packet Count overflows,
this status bit is set to 1 This overflow status is cleared after clearing PRBS byte counter using 0x620[1] |
| 9 | PRBS Checker Byte Count Overflow Status | R | 0h | If PRBS Checker Byte Count overflows,
this status bit is set to 1 This overflow status is cleared after clearing PRBS byte counter using 0x620[1] |
| 8 | PRBS Lock | R | 0h | 1b = PRBS checker is locked and synced with the received stream |
| 7-0 | PRBS Error Count | R | 0h | Writing 1 to bit0 locks all PRBS
counters Writing 1 to bit1 locks all PRBS counters and clears the counters on read of those specific registers Bits [1:0] are self-cleared after write Reading Bits[7:0] after writing bit0/bit1, gives the number of error bits received by PRBS checker When PRBS Count Mode set to zero, count stops on 0xFF |
PRBS_STATUS_6 is shown in Figure 8-85 and described in Table 8-89.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PRBS Packer Error Count-1 | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PRBS Packer Error Count-1 | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PRBS Packer Error Count-1 | R | 0h | Holds Bits [15:0] of number of total
packets received with error by the PRBS checker Value in register is locked when 0x620[0] or 0x620[1] are written When PRBS Count Mode set to zero, count stops on 0xFFFFFFFF This counter is cleared if 0x622,0x623 are read in the same order, after programming 0x620[1]=1 |
PRBS_STATUS_7 is shown in Figure 8-86 and described in Table 8-90.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PRBS Packer Error Count-2 | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PRBS Packer Error Count-2 | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PRBS Packer Error Count-2 | R | 0h | Holds Bits [31:16] of number of total
packets received with error by the PRBS checker Value in register is locked when 0x620[0] or 0x620[1] are written When PRBS Count Mode set to zero, count stops on 0xFFFFFFFF This counter is cleared if 0x622,0x623 are read in the same order, after programming 0x620[1]=1 |
PRBS_CTRL_4 is shown in Figure 8-87 and described in Table 8-91.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| MAC Packet Data | |||||||
| R/W-55h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| MAC Packet Mode | Pattern Length in MAC Packets | Packet Count for MAC packets Mode | |||||
| R/W-0h | R/W-2h | R/W-1h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | MAC Packet Data | R/W | 55h | Fixed data to be sent when MAC Packet Mode is set to Fixed mode |
| 7-6 | MAC Packet Mode | R/W | 0h | 00b = Incremental 01b = Fixed 10b = PRBS 11b = PRBS |
| 5-3 | Pattern Length in MAC Packets | R/W | 2h | MAC Packets have Destination Address,
Source Address, Programmed Pattern,
PRBS/Fixed/Incremental Data The length of Programmed Pattern can be confgured through this register. Pattern can be programmed through 0x625,0x626,0x627 000b = 6 bytes 001b = 1 bytes 010b = 2 bytes 011b = 3 bytes 100b = 4 bytes 101b = 5 bytes 110b = 6 bytes 111b = 6 bytes |
| 2-0 | Packet Count for MAC packets Mode | R/W | 1h | 000b = 1 packet 001b = 10 packets 010b = 100 packets 011b = 1000 packets 100b = 10000 packets 101b = 100000 packets 110b = 1000000 packets 111b = Continuous packets |
PATTERN_CTRL_1 is shown in Figure 8-88 and described in Table 8-92.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Pattern in MAC Packets [15:0] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Pattern in MAC Packets [15:0] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Pattern in MAC Packets [15:0] | R/W | 0h | Bytes 0,1 of programmable pattern in MAC packets |
PATTERN_CTRL_2 is shown in Figure 8-89 and described in Table 8-93.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Pattern in MAC Packets [31:16] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Pattern in MAC Packets [31:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Pattern in MAC Packets [31:16] | R/W | 0h | Bytes 2,3 of programmable pattern in MAC packets |
PATTERN_CTRL_3 is shown in Figure 8-90 and described in Table 8-94.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Pattern in MAC Packets [47:32] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Pattern in MAC Packets [47:32] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Pattern in MAC Packets [47:32] | R/W | 0h | Bytes 4,5 of programmable pattern in MAC packets |
PMATCH_CTRL_1 is shown in Figure 8-91 and described in Table 8-95.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Destination Address in MAC Packets [15:0] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Destination Address in MAC Packets [15:0] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Destination Address in MAC Packets [15:0] | R/W | 0h | Destination Address field in the generated MAC packets |
PMATCH_CTRL_2 is shown in Figure 8-92 and described in Table 8-96.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Destination Address in MAC Packets [31:16] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Destination Address in MAC Packets [31:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Destination Address in MAC Packets [31:16] | R/W | 0h | Destination Address field in the generated MAC packets |
PMATCH_CTRL_3 is shown in Figure 8-93 and described in Table 8-97.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Destination Address in MAC Packets [47:32] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Destination Address in MAC Packets [47:32] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Destination Address in MAC Packets [47:32] | R/W | 0h | Destination Address field in the generated MAC packets |
PKT_CRC_STAT is shown in Figure 8-94 and described in Table 8-98.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RX Bad CRC | TX Bad CRC | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-2 | RESERVED | R | 0h | Reserved |
| 1 | RX Bad CRC | R | 0h | 1b = CRC error detected in the packet received from the MDI receiver |
| 0 | TX Bad CRC | R | 0h | 1b = CRC error detected in the packet transmitted on MDI transmitter |
TX_PKT_CNT_1 is shown in Figure 8-95 and described in Table 8-99.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| TX Packet Count [15:0] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| TX Packet Count [15:0] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | TX Packet Count [15:0] | R | 0h | Lower 16 bits of TX packets from MAC
counter Note : Register is cleared when 0x639, 0x63A, 0x63B are read in sequence |
TX_PKT_CNT_2 is shown in Figure 8-96 and described in Table 8-100.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| TX Packet Count [31:16] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| TX Packet Count [31:16] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | TX Packet Count [31:16] | R | 0h | Upper 16 bits of TX packets from MAC
counter Note : Register is cleared when 0x639, 0x63A, 0x63B are read in sequence |
TX_PKT_CNT_3 is shown in Figure 8-97 and described in Table 8-101.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| TX Error Packet Count | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| TX Error Packet Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | TX Error Packet Count | R | 0h | TX packets from MAC with CRC error
counter Note : Register is cleared when 0x639, 0x63A, 0x63B are read in sequence |
RX_PKT_CNT_1 is shown in Figure 8-98 and described in Table 8-102.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RX Packet Count [15:0] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RX Packet Count [15:0] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | RX Packet Count [15:0] | R | 0h | Lower 16 bits of RX packets received
from MDI Note : Register is cleared when 0x63C, 0x63D, 0x63E are read in sequence |
RX_PKT_CNT_2 is shown in Figure 8-99 and described in Table 8-103.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RX Packet Count [31:16] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RX Packet Count [31:16] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | RX Packet Count [31:16] | R | 0h | Upper 16 bits of RX packets received
from MDI Note : Register is cleared when 0x63C, 0x63D, 0x63E are read in sequence |
RX_PKT_CNT_3 is shown in Figure 8-100 and described in Table 8-104.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RX Error Packet Count | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RX Error Packet Count | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | RX Error Packet Count | R | 0h | Rx packet w error (CRC error)
counter Note : Register is cleared when 0x63C, 0x63D, 0x63E are read in sequence |
RMII_CTRL_1 is shown in Figure 8-101 and described in Table 8-105.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | RESERVED | RMII Half Full Threshold | |||||
| R-0h | R-0h | R/W-2h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RMII Half Full Threshold | RMII Enable | RESERVED | RMII Follower Enable | RESERVED | RESERVED | RMII Rev1.0 Enable | RMII Enhanced Mode Enable |
| R/W-2h | R/W-Xh | R-0h | R/W-Xh | R-0h | R-0h | R/W-0h | R/W-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-11 | RESERVED | R | 0h | Reserved |
| 10 | RESERVED | R | 0h | Reserved |
| 9-7 | RMII Half Full Threshold | R/W | 2h | FIFO Half Full Threshold in nibbles for the RMII Rx FIFO |
| 6 | RMII Enable | R/W | 0h | 1b = RMII Enable |
| 5 | RESERVED | R | 0h | Reserved |
| 4 | RMII Follower Enable | R/W | 0h | 1b = RMII Follower mode is enabled Not recommended to configure this bit. Can be used as a status bit |
| 3 | RESERVED | R | 0h | Reserved |
| 2 | RESERVED | R | 0h | Reserved |
| 1 | RMII Rev1.0 Enable | R/W | 0h | 1b = Enable RMII rev1.0 |
| 0 | RMII Enhanced Mode Enable | R/W | 0h | 1b = Enable RMII Enhanced mode |
RMII_STATUS_1 is shown in Figure 8-102 and described in Table 8-106.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RMII FIFO Empty Error | RMII FIFO Full Error | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-2 | RESERVED | R | 0h | Reserved |
| 1 | RMII FIFO Empty Error | R | 0h | Clear on read bit RMII fifo undeflow error status |
| 0 | RMII FIFO Full Error | R | 0h | Clear on Read bit RMII fifo overflow status |
PTP_CTL is shown in Figure 8-103 and described in Table 8-107.
Return to the Summary Table.
This register provides basic controls for the PTP 802.1AS operation
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Trigger Select | Trigger Disable | Trigger Enable | ||||
| R-0h | R/W-0h | R/W-0h | R/W-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Trigger Read | Trigger Load | Read PTP Clock | Load PTP Clock | Step PTP Clock | PTP Enable | PTP Disable | PTP Reset |
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-13 | RESERVED | R | 0h | Reserved |
| 12-10 | Trigger Select | R/W | 0h | PTP Trigger Select: This field selects the Trigger for loading control information or for enabling the Trigger. 000b = Trigger-0 001b = Trigger-1 010b = Trigger-2 011b = Trigger-3 100b = Trigger-4 101b = Trigger-5 110b = Trigger-6 111b = Trigger-7 |
| 9 | Trigger Disable | R/W | 0h | Disable PTP Trigger: Setting this bit will disable the selected Trigger. This bit does not indicate Disable status for Triggers. The PTP Trigger Status Register should be used to determine Trigger Status. This bit is self-clearing and will always read back as 0. Disabling a Trigger will not disconnect it from a GPIO pin. The Trigger value will still be driven to the GPIO if the Trigger is assigned to a GPIO. |
| 8 | Trigger Enable | R/W | 0h | Enable PTP Trigger: Setting this bit will enable the selected Trigger. This bit does not indicate Enable status for Triggers. The PTP Trigger Status Register should be used to determine Trigger Status. This bit is self-clearing and will always read back as 0. |
| 7 | Trigger Read | R/W | 0h | Read PTP Trigger: Setting this bit will begin the Trigger Read process. The Trigger is selected based on the setting of the 'Trigger Select' bits in this register. Upon setting this bit, subsequent reads of the PTP_TDR register will return the Trigger Control values. This bit is self-clearing and will always read back as 0. |
| 6 | Trigger Load | R/W | 0h | Load PTP Trigger: Setting this bit will disable the selected Trigger and begin the Trigger load process. The Trigger is selected based on the setting of the 'Trigger Select' bits in this register. Upon setting this bit, subsequent writes to the PTP_TDR will set the Trigger Control fields for the selected Trigger. The Trigger Load is completed once all fields have been written, or the 'Trigger Enable' bit has been set in this register. This bit is self-clearing and will read back as 0 when the Trigger Load is completed either by writing all Trigger Control fields, or by setting the Trigger Enable. |
| 5 | Read PTP Clock | R/W | 0h | Read PTP Clock: Setting this bit will cause the device to sample the PTP Clock time value. The time value will be made available for reading through the PTP_TDR register. This bit is self-clearing and will always read back as 0. |
| 4 | Load PTP Clock | R/W | 0h | Load PTP Clock: Setting this bit will cause the device to load the PTP Clock time value from data previously written to the PTP_TDR register. This bit is self-clearing and will always read back as 0. |
| 3 | Step PTP Clock | R/W | 0h | Step PTP Clock: Setting this bit will cause the device to add a value to the PTP Clock. The value to be added is the value previously written to the PTP_TDR register. This bit is self-clearing and will always read back as 0. |
| 2 | PTP Enable | R/W | 0h | Enable PTP Clock: Setting this bit will enable the PTP Clock. Reading this bit will return the current enabled value. Writing a 0 to this bit will have no effect. |
| 1 | PTP Disable | R/W | 0h | Disable PTP Clock: Setting this bit will disable the PTP Clock. Writing a 0 to this bit will have no effect. This bit is self-clearing and will always read back as 0. |
| 0 | PTP Reset | R/W | 0h | Reset PTP Clock: Setting this bit will reset the PTP Clock and associated logic. In addition, the 802.1AS registers will be reset, with the exception of the PTP_COC and PTP_CLKSRC registers. Unlike other bits in this register, this bit is not self-clearing and must be written to 0 to release the clock and logic from reset. |
PTP_TDR is shown in Figure 8-104 and described in Table 8-108.
Return to the Summary Table.
This register provides a mechanism for reading and writing the 802.1AS Time and Trigger Control values. The function of this register is determined by controls in the PTP control register
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Time Data | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Time Data | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Time Data | R/W | 0h | Time Data: On Reads, successively returns 16-bit values of the Clock time or Trigger Control information as selected by controls in the PTP Control Register. Additional reads beyond the available fields will always return 0. On Writes, successively stores the 16-bit values of Clock time or Trigger Control Information as selected by controls in the PTP Control Register. |
PTP_STS is shown in Figure 8-105 and described in Table 8-109.
Return to the Summary Table.
This register provides basic status and interrupt control for the 802.1AS PTP operation.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | CRF RX Timestamp Ready | TX Timestamp Ready | RX Timestamp Ready | Trigger Done | Event Ready | ||
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | CRF RX Timestamp Ready Interrupt Enable | TX Timestamp Ready Interrupt Enable | RX Timestamp Ready Interrupt Enable | Trigger Done Interrupt Enable | Event Ready Enable | ||
| R-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | ||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-13 | RESERVED | R | 0h | Reserved |
| 12 | CRF RX Timestamp Ready | R | 0h | CRF receive Timestamp ready: A CRF Receive Timestamp is available for an inbound CRF Message. This bit will be cleared upon read of the Receive Timestamp if no other timestamps are ready. |
| 11 | TX Timestamp Ready | R | 0h | Transmit Timestamp Ready: A Transmit Timestamp is available for an outbound PTP Message. This bit will be cleared upon read of the Transmit Timestamp if no other timestamps are ready. |
| 10 | RX Timestamp Ready | R | 0h | Receive Timestamp Ready: A Receive Timestamp is available for an inbound PTP Message. This bit will be cleared upon read of the Receive Timestamp if no other timestamps are ready. |
| 9 | Trigger Done | R | 0h | PTP Trigger Done: A PTP Trigger has occurred. This bit will be cleared upon read. This bit will only be set if Trigger Notification is turned on for the Trigger through the Trigger Configuration Registers. Note that if periodic trigger is set, this interrupt will not get asserted unless the programmed trigger has resulted in a erroneous condition. If TRIG_IF_LATE bit is set, even an erroneous condition will not give out an interrupt |
| 8 | Event Ready | R | 0h | PTP Event Timestamp Ready: A PTP Event Timestamp is available. This bit will be cleared upon read of the PTP Event Status Register if no other event timestamps are ready. |
| 7-5 | RESERVED | R | 0h | Reserved |
| 4 | CRF RX Timestamp Ready Interrupt Enable | R/W | 0h | Enable CRF receive Timestamp
interrupt: Enable Interrupt on CRF Receive Timestamp Ready. |
| 3 | TX Timestamp Ready Interrupt Enable | R/W | 0h | Enable Transmit Timestamp Interrupt: Enable Interrupt on Transmit Timestamp Ready. |
| 2 | RX Timestamp Ready Interrupt Enable | R/W | 0h | Enable Receive Timestamp Interrupt: Enable Interrupt on Receive Timestamp Ready. |
| 1 | Trigger Done Interrupt Enable | R/W | 0h | Enable Trigger Interrupt: Enable Interrupt on Trigger Completion. |
| 0 | Event Ready Enable | R/W | 0h | Enable Event Interrupt: Enable Interrupt on Event Timestamp Ready. |
PTP_TSTS is shown in Figure 8-106 and described in Table 8-110.
Return to the Summary Table.
This register provides status of the 802.1AS PTP Triggers. The bits in this register indicate the current status for each of the Trigger modules. The error bits will be set if the associated notification enable (TRIG_NOTIFY) is set in the PTP Trigger Configuration Registers
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Trigger-7 Error Indication | Trigger-7 Active Status | Trigger-6 Error Indication | Trigger-6 Active Status | Trigger-5 Error Indication | Trigger-5 Active Status | Trigger-4 Error Indication | Trigger-4 Active Status |
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Trigger-3 Error Indication | Trigger-3 Active Status | Trigger-2 Error Indication | Trigger-2 Active Status | Trigger-1 Error Indication | Trigger-1 Active Status | Trigger-0 Error Indication | Trigger-0 Active Status |
| R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h | R-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Trigger-7 Error Indication | R | 0h | This bit indicates that the Trigger was
improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the
Trigger is disabled and/ or rearmed. |
| 14 | Trigger-7 Active Status | R | 0h | This bit indicates that the Trigger is
enabled and has not completed. |
| 13 | Trigger-6 Error Indication | R | 0h | This bit indicates that the Trigger was
improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the
Trigger is disabled and/ or rearmed. |
| 12 | Trigger-6 Active Status | R | 0h | This bit indicates that the Trigger is
enabled and has not completed. |
| 11 | Trigger-5 Error Indication | R | 0h | This bit indicates that the Trigger was
improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the
Trigger is disabled and/ or rearmed. |
| 10 | Trigger-5 Active Status | R | 0h | This bit indicates that the Trigger is
enabled and has not completed. |
| 9 | Trigger-4 Error Indication | R | 0h | This bit indicates that the Trigger was
improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the
Trigger is disabled and/ or rearmed. |
| 8 | Trigger-4 Active Status | R | 0h | This bit indicates that the Trigger is
enabled and has not completed. |
| 7 | Trigger-3 Error Indication | R | 0h | This bit indicates that the Trigger was
improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the
Trigger is disabled and/ or rearmed. |
| 6 | Trigger-3 Active Status | R | 0h | This bit indicates that the Trigger is
enabled and has not completed. |
| 5 | Trigger-2 Error Indication | R | 0h | This bit indicates that the Trigger was
improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the
Trigger is disabled and/ or rearmed. |
| 4 | Trigger-2 Active Status | R | 0h | This bit indicates that the Trigger is
enabled and has not completed. |
| 3 | Trigger-1 Error Indication | R | 0h | This bit indicates that the Trigger was
improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the
Trigger is disabled and/ or rearmed. |
| 2 | Trigger-1 Active Status | R | 0h | This bit indicates the Trigger is
enabled and has not completed. |
| 1 | Trigger-0 Error Indication | R | 0h | This bit indicates that the Trigger was
improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the
Trigger is disabled and/ or rearmed. |
| 0 | Trigger-0 Active Status | R | 0h | This bit indicates that the Trigger is
enabled and has not completed. |
PTP_RATEL is shown in Figure 8-107 and described in Table 8-111.
Return to the Summary Table.
This register contains the low 16-bits of the PTP Rate control. The PTP Rate Control indicates a positive or negative adjustment to the reference clock period in units of 2-32ns. On each reference clock cycle, the PTP Clock will be adjusted by adding ref_clk_period +/- PTP_Rate. The PTP Rate should be written as PTP_RATEH, followed by PTP_RATEL. The rate will take effect on the write to the PTP_RATEL register
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Rate Control Low | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Rate Control Low | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Rate Control Low | R/W | 0h | PTP Rate Control Low 16-bits: Writing to this register will set the low 16-bits of the Rate Control value. The Rate Control value is in units of 2-32ns. Upon writing to this register, the full Rate Control value will be loaded to the device. |
PTP_RATEH is shown in Figure 8-108 and described in Table 8-112.
Return to the Summary Table.
This register contains the upper 10-bits of the 26-bit PTP Rate control. In addition, it contains a direction control to indicate whether the device is operating faster or slower than the reference clock frequency. When setting the PTP Rate, this register should be written first, followed by a write to the PTP_RATEL register. The rate will take effect on the write to the PTP_RATEL register.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Rate Direction | Temporary Rate Enable | RESERVED | PTP Rate Control High | ||||
| R/W-0h | R/W-0h | R-0h | R/W-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Rate Control High | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | PTP Rate Direction | R/W | 0h | The setting of this bit controls
whether the device will operate at a higher or lower
frequency than the reference clock.
|
| 14 | Temporary Rate Enable | R/W | 0h | PTP Temporary Rate: Setting this bit will cause the rate to be applied to the clock for the duration set in the PTP Temporary Rate Duration Register (PTP_TRD).
|
| 13-10 | RESERVED | R | 0h | Reserved |
| 9-0 | PTP Rate Control High | R/W | 0h | PTP Rate Control High 10-bits: Writing to this register will set the high 10-bits of the Rate Control value. The Rate Control value is in units of 2-32ns. |
PTP_TXTS is shown in Figure 8-109 and described in Table 8-113.
Return to the Summary Table.
This register provides a
mechanism for reading the Transmit Timestamp. The fields are read in the
following order:
Timestamp_ns [15:0];
Overflow_cnt[1:0], Timestamp_ns[29:16];
Timestamp_sec[15:0],
Timestamp_sec[31:16]
The Overflow_cnt value indicates if timestamps
were dropped due to an overflow of the Transmit Timestamp queue. The
overflow counter will stick at a value of three if additional timestamps
were missed.
Note:
Each
Transmit Timestamp information consists of Four reads. TXTS_RDY status
(0xD02, Bit-11) is required to be read to access the next available Transmit
Timestamp information.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP TX Timestamp | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP TX Timestamp | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP TX Timestamp | R | 0h | PTP Transmit Timestamp: Reading this register will return the Transmit Timestamp in four 16-bit reads. |
PTP_RXTS is shown in Figure 8-110 and described in Table 8-114.
Return to the Summary Table.
This register provides a
mechanism for reading the Receive Timestamp and identification information.
The fields are read in the following order:
Timestamp_ns [15:0]
Overflow_cnt[1:0], Timestamp_ns[29:16]
Timestamp_sec[15:0]
Timestamp_sec[31:16]
sequenceId[15:0]
messageType[3:0], source_hash[11:0]
The Overflow_cnt value indicates if timestamps
were dropped due to an overflow of the Transmit Timestamp queue. The
overflow counter will stick at a value of three if additional timestamps
were missed.
Note:
Each
Receive Timestamp information consists of Six reads. RXTS_RDY status (0xD02,
Bit-12) is required to be read to access the next available Receive
Timestamp information.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP RX Timestamp | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP RX Timestamp | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP RX Timestamp | R | 0h | PTP Receive Timestamp: Reading this register will return the Receive Timestamp and identification information in successive 16-bit reads. |
PTP_ESTS is shown in Figure 8-111 and described in Table 8-115.
Return to the Summary Table.
This register provides Status for the Event Timestamp unit. Reading this register provides status for the next Event Timestamp contained in the Event Data Register. If this register is 0, no Event Timestamp is available in the Event Data Register. Reading this register will automatically move to the next Event in the queue.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Events Missed Counter | ||||||
| R-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Event Timestamp Change Length | Event Edge Detected | Event Number Detected | Multiple Events Detected | PTP Event Detected | |||
| R-0h | R-0h | R-0h | R-0h | R-0h | |||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-11 | RESERVED | R | 0h | Reserved |
| 10-8 | Events Missed Counter | R | 0h | Number of Events Missed: Indicates number of events have been missed prior to this timestamp for the EVNT_NUM indicated. This count value will stick at 7 if more than 7 events are missed. |
| 7-6 | Event Timestamp Change Length | R | 0h | Event Timestamp Length: Indicates length of the Timestamp field in 16-bit words minus 1. Although all fields are available, this indicates how many of the fields contain data different from the previous Event Timestamp. This allows software to avoid reading more significant fields if they have not changed since the previous timestamp. This field is valid for both single and multiple events. The following shows the number of least significant fields which have new data for each setting
|
| 5 | Event Edge Detected | R | 0h | Event edge configuration: Indicates whether the event is a rise or falling event. If the 'Multiple Event Detected' bit is set to 1, this bit indicates the Rise/Fall direction for the event indicated by EVNT_NUM.
|
| 4-2 | Event Number Detected | R | 0h | Event Number: Indicates Event Timestamp Unit which detected an event. If the 'Multiple Event Detected' bit is 1, this indicates the lowest event number captured. If events have been missed prior to this timestamp, it indicates the lowest event number captured which had at least one missed event. |
| 1 | Multiple Events Detected | R | 0h | Multiple Event Detect: Indicates multiple events were detected at the same time. If multiple events are detected, an extended event status field is available as the first data read from the Event Data Register.
|
| 0 | PTP Event Detected | R | 0h | Indicates an Event has been detected by one of the Event Timestamp Units |
PTP_EDATA is shown in Figure 8-112 and described in Table 8-116.
Return to the Summary Table.
This register provides a
mechanism for reading the Event Timestamp and extended event status. If
present, the extended event status is read prior to reading the Event
Timestamp. Presence of the Extended Event Status field is indicated by the
MULT_EVNT bit in the PTP Event Status Register. The timestamp consists of
four 16-bit fields. This register contains a valid timestamp if the PTP_ESTS
register indicates an Event Timestamp is available. Not all fields have to
be read for each timestamp. For example, if the EVNT_TS_LEN indicates the
seconds field has not changed from the previous event, software may skip
that read. Reading the PTP_ESTS register will cause the device to move to
the next available timestamp.
The fields are
read in the following order:
Extended Event Status[15:0] (only available if
PTP_ESTS indicates detection of multiple events)
Timestamp_ns [15:0]
Timestamp_ns[29:16] (upper 2 bits are always
0)
Timestamp_sec[15:0]
Timestamp_sec[31:16]
For Extended Event Status, the following
definition is used for the PTP Event Data Register:
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Event Data | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Event Data | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Event Data | R | 0h | PTP Event Data register: For timestamp fields, the following definition is used for the PTP Event Data Register: PTP Event Timestamp: Reading this register will return 16-bits of the Event Timestamp. |
PTP_EDATA_ES is shown in Figure 8-113 and described in Table 8-117.
Return to the Summary Table.
Extended Event Status[15:0] register description
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Event-7 Rise | Event-7 Detect | Event-6 Rise | Event-6 Detect | Event-5 Rise | Event-5 Detect | Event-4 Rise | Event-4 Detect |
| RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Event-3 Rise | Event-3 Detect | Event-2 Rise | Event-2 Detect | Event-1 Rise | Event-1 Detect | Event-0 Rise | Event-0 Detect |
| RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h | RC-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Event-7 Rise | RC | 0h | Rise/Fall edge direction for Event 7: Indicates direction of Event 7
|
| 14 | Event-7 Detect | RC | 0h | Event 7 detected: Indicates Event 6 detected a rising or falling edge at the time contained in the PTP_EDATA register timestamp. |
| 13 | Event-6 Rise | RC | 0h | Rise/Fall edge direction for Event 6: Indicates direction of Event 6
|
| 12 | Event-6 Detect | RC | 0h | Event 6 detected: Indicates Event 6 detected a rising or falling edge at the time contained in the PTP_EDATA register timestamp. |
| 11 | Event-5 Rise | RC | 0h | Rise/Fall edge direction for Event 5: Indicates direction of Event 5
|
| 10 | Event-5 Detect | RC | 0h | Event 5 detected: Indicates Event 5 detected a rising or falling edge at the time contained in the PTP_EDATA register timestamp |
| 9 | Event-4 Rise | RC | 0h | Rise/Fall edge direction for Event 4: Indicates direction of Event 4
|
| 8 | Event-4 Detect | RC | 0h | Event 4 detected: Indicates Event 4 detected a rising or falling edge at the time contained in the PTP_EDATA register timestamp. |
| 7 | Event-3 Rise | RC | 0h | Rise/Fall edge direction for Event
3: Indicates direction of Event 3
|
| 6 | Event-3 Detect | RC | 0h | Event 3 detected: Indicates Event 3 detected a rising or falling edge at the time contained in the PTP_EDATA register timestamp. |
| 5 | Event-2 Rise | RC | 0h | Rise/Fall edge direction for Event 2: Indicates direction of Event 2
|
| 4 | Event-2 Detect | RC | 0h | Event 2 detected: Indicates Event 2 detected a rising or falling edge at the time contained in the PTP_EDATA register timestamp. |
| 3 | Event-1 Rise | RC | 0h | Rise/Fall edge direction for Event 1: Indicates direction of Event 1
|
| 2 | Event-1 Detect | RC | 0h | Event 1 detected: Indicates Event 1 detected a rising or falling edge at the time contained in the PTP_EDATA register timestamp. |
| 1 | Event-0 Rise | RC | 0h | Rise/Fall edge direction for Event 0: Indicates direction of Event 0
|
| 0 | Event-0 Detect | RC | 0h | Event 0 detected: Indicates Event 0 detected a rising or falling edge at the time contained in the PTP_EDATA register timestamp. |
PTP_TRIG is shown in Figure 8-114 and described in Table 8-118.
Return to the Summary Table.
This register provides basic configuration for IEEE 802.1AS Triggers. To
write configuration to a trigger, set the TRIG_WR bit along with the
TRIG_SEL and other control information. To read configuration from a
trigger, set the TRIG_SEL ePTP_PLLding to the trigger desired, and set the
TRIG_WR bit to 0. The subsequent read of the PTP_TRIG register will return
the configuration information.
Note:
A Pulse is
seen in case toggle trigger is set with trig_if_late condition.
In trig_if_late condition, pulse trigger
doesnt give pulse of the configured width.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Trigger Pulse Select | Trigger Periodic Enable | Trigger If Late | Trigger Notification Enable | Tigger GPIO Select | |||
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Tigger Toggle Mode | RESERVED | Trigger Select | Trigger Configuration Write | ||||
| R/W-0h | R-0h | R/W-0h | R/W-0h | ||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Trigger Pulse Select | R/W | 0h | Trigger Pulse: Setting this bit will cause the trigger to generate a pulse rather than a single rising or falling edge. |
| 14 | Trigger Periodic Enable | R/W | 0h | Trigger Periodic: Setting this bit will cause the trigger to generate a periodic signal. If this bit is 0, the trigger will generate a single Pulse or Edge depending on the Trigger Control settings. |
| 13 | Trigger If Late | R/W | 0h | Trigger-if-late Control: Setting this bit will allow an immediate trigger in the event the trigger is programmed to a time value which is less than the current time. This provides a mechanism for generating an immediate trigger or to immediately begin generating a periodic signal. For a periodic signal, no notification will be generated if this bit is set and a late trigger occurs. This function should only be used for Trigger 0 or Trigger 1. This bit has to be programmed before loading the trigger (loading the timestamp). |
| 12 | Trigger Notification Enable | R/W | 0h | Trigger Notification Enable: Setting this bit will enable trigger status to be reported on completion of a trigger or on an error detection due to late trigger. If trigger interrupts are enabled, the notification will also result in an interrupt being generated. |
| 11-8 | Tigger GPIO Select | R/W | 0h | GPIO trigger output configuration: Setting this field to a non-zero value will connect the trigger to the associated GPIO pin.
|
| 7 | Tigger Toggle Mode | R/W | 0h | Trigger Toggle mode enable: Setting this bit will put the trigger into toggle mode. In toggle mode, the initial value will be ignored and the trigger output will be toggled at the trigger time. |
| 6-4 | RESERVED | R | 0h | Reserved |
| 3-1 | Trigger Select | R/W | 0h | Trigger Configuration Select: This field selects the trigger for configuration read or write. |
| 0 | Trigger Configuration Write | R/W | 0h | Trigger Configuration Write: Setting this bit will generate a Configuration Write to the selected trigger. This bit is self-clear bit and will always read back as 0. |
PTP_EVNT is shown in Figure 8-115 and described in Table 8-119.
Return to the Summary Table.
This register provides basic configuration for IEEE 802.1AS Events. To
write configuration to an Event Timestamp Unit, set the EVNT_WR bit along
with the EVNT_SEL and other control information. To read configuration from
an Event Timestamp Unit, set the EVNT_SEL ePTP_PLLding to the Event desired,
and set the EVNT_WR bit to 0. The subsequent read of the PTP_EVNT register
will return the configuration information.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Event Rise Detect Enable | Event Fall Detect Enable | Single Event Capture | Event GPIO Select | |||
| R-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Event Select | Event Configuration Write | |||||
| R-0h | R/W-0h | R/W-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | Event Rise Detect Enable | R/W | 0h | Event Rise Detect Enable: Enable detection of a rising edge transition on the selected event input. |
| 13 | Event Fall Detect Enable | R/W | 0h | Event Fall Detect Enable: Enable detection of a falling edge transition on the selected event input. |
| 12 | Single Event Capture | R/W | 0h | Single Event Capture: Setting this bit to a 1 will enable single event capture operation. The EVNT_RISE and EVNT_FALL enables will be cleared upon a valid event timestamp capture. |
| 11-8 | Event GPIO Select | R/W | 0h | GPIO event capture configuration: Setting this field to a non-zero value will connect the event to the associated GPIO pin. This field can also be used to capture events based on trigger outputs
|
| 7-4 | RESERVED | R | 0h | Reserved |
| 3-1 | Event Select | R/W | 0h | Event Select: This field selects the Event Timestamp Unit for configuration read or write. 000b = Event-0 001b = Event-1 010b = Event-2 011b = Event-3 100b = Event-4 101b = Event-5 110b = Event-6 111b = Event-7 |
| 0 | Event Configuration Write | R/W | 0h | Event Configuration Write: Setting this bit will generate a Configuration Write to the selected Event Timestamp Unit. |
PTP_TXCFG0 is shown in Figure 8-116 and described in Table 8-120.
Return to the Summary Table.
This register provides configuration for IEEE 802.1AS Transmit Timestamp
operation.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Sync Message One-Step Enable | TX TimeStamp Info Enable | Insert Delay Request | NTP Timestamp Enable | Ignore Two-Step Flag | Disable CRC One-Step | Checksum Coreection One-Step | IP Address Filter |
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h |
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Layer2 Timestamp Enable | IPv6 Timestamp Enable | IPv4 Timestamp Enable | PTP Version | Transmit Timestamp Enable | |||
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | |||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Sync Message One-Step Enable | R/W | 0h | Sync Message One-Step Enable: Enable automatic insertion of timestamp into transmit Sync Messages. Device will automatically parse message and insert the timestamp in the correct location. UDP checksum and CRC fields will be regenerated. |
| 14 | TX TimeStamp Info Enable | R/W | 0h | Enable latching of message type, hash value, sequence id along with Timestamp for transmit event packets and transmit these fields through PSF |
| 13 | Insert Delay Request | R/W | 0h | Insert Delay_Req timestamp in
Delay_Resp: If this bit is set to a 1, the device inserts the timestamp for transmitted Delay_Req messages into inbound Delay_Resp messages. The most recent timestamp will be used for any inbound Delay_Resp message. The receive timestamp insertion logic must be enabled through the PTP Receive Configuration Registers. |
| 12 | NTP Timestamp Enable | R/W | 0h | Enable Timestamping of NTP Packets: If this bit is set to 0, the device will check the UDP protocol field for a PTP Event message (value 319). If this bit is set to 1, the device will check the UDP protocol field for an NTP message (value 123). This setting applies to the transmit and receive packet parsing engines. |
| 11 | Ignore Two-Step Flag | R/W | 0h | Ignore Two_Step flag for One-Step
operation: If this bit is set to a 0, the device will not insert a timestamp if the Two_Step bit is set in the flags field of the PTP header. If this bit is set to 1, the device will insert a timestamp independent of the setting of the Two_Step flag. |
| 10 | Disable CRC One-Step | R/W | 0h | Disable checking of CRC for One-Step
operation: If this bit is set to a 0, the device will force a CRC error for One-Step operation if the incoming frame has a CRC error. If this bit is set to a 1, the device will send the One-Step frame with a valid CRC, even if the incoming CRC is invalid. |
| 9 | Checksum Coreection One-Step | R/W | 0h | Enable UDP Checksum correction for
One-Step Operation: Enables correction of the UDP checksum for messages which include insertion of the timestamp. The checksum is corrected by modifying the last two bytes of the UDP data. The last two bytes must be transmitted by the MAC as 0 's. This control must be set for proper IPv6/UDP One-Step operation. This control will have no effect for Layer2 Ethernet messages. |
| 8 | IP Address Filter | R/W | 0h | Enable IEEE 802.1AS defined IP address
filter: Enable filtering of UDP/IP Event messages using the IANA assigned IP Destination addresses. If this bit is set to 1, packets with IP Destination addresses which do not match the IANA assigned addresses will not be timestamped. This field affects operation for both IPv4 and IPv6. If this field is set to 0, IP destination addresses will be ignored. |
| 7 | Layer2 Timestamp Enable | R/W | 0h | Layer2 Timestamp Enable: Enables detection of IEEE 802.3/Ethernet encapsulated PTP event messages. |
| 6 | IPv6 Timestamp Enable | R/W | 0h | IPv6 Timestamp Enable: Enables detection of UDP/IPv6 encapsulated PTP event messages. |
| 5 | IPv4 Timestamp Enable | R/W | 0h | IPv4 Timestamp Enable: Enables detection of UDP/IPv4 encapsulated PTP event messages. |
| 4-1 | PTP Version | R/W | 0h | PTP Version: Enable Timestamp capture for a specific version of the IEEE 802.1AS specification. This field may be programmed to any value between 1 and 15 and allows support for future versions of the IEEE 802.1AS specification. A value of 0 will disable version checking (not recommended). |
| 0 | Transmit Timestamp Enable | R/W | 0h | Transmit Timestamp Enable: Enable Timestamp capture for Transmit. |
PTP_TXCFG1 is shown in Figure 8-117 and described in Table 8-121.
Return to the Summary Table.
This register provides data and mask fields to filter the first byte in a
PTP Message. This function will be disabled if all the mask bits are set to
0.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Trasmit Byte0 Mask | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Transmit Byte0 Data | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | Trasmit Byte0 Mask | R/W | 0h | Byte0 Mask: Bit mask to be used for matching Byte0 of the PTP Message. A one in any bit enables matching for the associated data bit. If no matching is required, all bits of the mask should be set to 0 |
| 7-0 | Transmit Byte0 Data | R/W | 0h | Byte0 Data: Data to be used for matching Byte0 of the PTP Message. |
PSF_CFG0 is shown in Figure 8-118 and described in Table 8-122.
Return to the Summary Table.
This register provides configuration for the Phy Status Frame function.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | PSF Termination Field Addition Enable | RESERVED | PSF MAC Source Address | PSF Minimum Preamble | |||
| R-0h | R/W-1h | R-0h | R/W-0h | R/W-7h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PSF Endian Control | PSF Packet Type | PSF Delivery Enable | PSF Error Delivery Enable | PSF TX Timestamp Enable | PSF RX Timestamp Enable | PSF Trigger Enable | PSF Event Enable |
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h |
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | PSF Termination Field Addition Enable | R/W | 1h | 1b = Enable addition of termination field for PSF packets |
| 13 | RESERVED | R | 0h | Reserved |
| 12-11 | PSF MAC Source Address | R/W | 0h | Phy Status Frame Mac Source Address:
|
| 10-8 | PSF Minimum Preamble | R/W | 7h | Phy Status Frame minimum preamble: Determines the minimum preamble bytes required for sending packets on the MII interface. It is recommended that this be set to the smallest value the MAC will tolerate. |
| 7 | PSF Endian Control | R/W | 0h | Phy Status Frame Endian control: For each 16-bit field in a Status Message, the data will normally be presented in network byte order (Most significant byte first). If this bit is set to a 1, the byte data fields will be reversed so that the least significant byte is first. |
| 6 | PSF Packet Type | R/W | 0h | This bit controls the type of packet
used for Phy Status Frames:
|
| 5 | PSF Delivery Enable | R/W | 0h | Phy Control Frame Read Phy Status Frame
enable: Enable Phy Status Frame delivery of Phy Control Frame read data. Data read via a Phy Control Frame will be returned in a Phy Status Frame. |
| 4 | PSF Error Delivery Enable | R/W | 0h | PSF Error Phy Status Frame enable: Enable Phy Status Frame delivery of Phy Status Frame Errors. This bit will not independently enable Phy Status Frame operation. One of the other enable bits must be set for Phy Status Frames to be generated. |
| 3 | PSF TX Timestamp Enable | R/W | 0h | Transmit Timestamp Phy Status Frame
enable: Enable Phy Status Frame delivery of Transmit Timestamps. |
| 2 | PSF RX Timestamp Enable | R/W | 0h | Receive Timestamp Phy Status Frame
enable: Enable Phy Status Frame delivery of Receive Timestamps. |
| 1 | PSF Trigger Enable | R/W | 0h | Trigger Phy Status Frame enable: Enable Phy Status Frame delivery of Trigger Status. |
| 0 | PSF Event Enable | R/W | 0h | Event Phy Status Frame enable: Enable Phy Status Frame delivery of Event Timestamps. |
PTP_RXCFG0 is shown in Figure 8-119 and described in Table 8-123.
Return to the Summary Table.
This register provides configuration for IEEE 802.1AS Receive Timestamp
operation.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Domain Match Enable | Alternate Leader Timestamp Enable | IP Address Data Select | User Programmed IP Address Filter Enable | PTP Receive Follower Only | IP Address Filters Enable | ||
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | ||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| L2 Timetamp Enable | IPv6 Timestamp Enable: | IPv4 Timestamp Enable: | RX PTP Version | Receive Timestamp Enable | |||
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | |||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Domain Match Enable | R/W | 0h | Domain Match Enable: If set to 1, the Receive Timestamp unit will require the domain Number field (octet 4) of the PTP Header to match the value programmed in the PTP_DOMAIN field of the PTP_RXCFG3 register. If set to 0, the Receive Timestamp will ignore the PTP_DOMAIN field. |
| 14 | Alternate Leader Timestamp Enable | R/W | 0h | Alternate Leader Timestamp Disable: Disables Timestamp generation if the Alternate_Leader flag is set.
|
| 13 | IP Address Data Select | R/W | 0h | IP Address data select: Selects portion of IP address accessible through the PTP_RXCFG2 register.
|
| 12 | User Programmed IP Address Filter Enable | R/W | 0h | Enable User-programmed IP address filter: Enable detection of UDP/IP Event messages using a programmable IP address. The IP Address is set using the PTP_RXCFG2 register. |
| 11 | PTP Receive Follower Only | R/W | 0h | Receive Follower Only: By default, the Receive Timestamp Unit will provide Timestamps for event messages meeting other requirements. Setting this bit to a 1 will prevent Delay_Req messages from being Timestamped by requiring that the Control Field (offset 32 in the PTP message) be set to a value other than 1. |
| 10-8 | IP Address Filters Enable | R/W | 0h | Enable IEEE 802.1AS defined IP address
filters: Enable detection of UDP/IP Event messages using the IANA assigned IP Destination addresses. This field affects operation for both IPv4 and IPv6. A Timestamp is captured for the PTP message if the IP destination address matches the following: bxx1 : Dest IP address is 224.0.1.129 bx1x : Dest IP address is 224.0.1.130 - 132 b1xx : Dest IP address is 224.0.0.107 |
| 7 | L2 Timetamp Enable | R/W | 0h | Layer2 Timestamp Enable: Enables detection of IEEE 802.3/Ethernet encapsulated PTP event messages. |
| 6 | IPv6 Timestamp Enable: | R/W | 0h | IPv6 Timestamp Enable: Enables detection of UDP/IPv6 encapsulated PTP event messages. |
| 5 | IPv4 Timestamp Enable: | R/W | 0h | IPv4 Timestamp Enable: Enables detection of UDP/IPv4 encapsulated PTP event messages. |
| 4-1 | RX PTP Version | R/W | 0h | PTP Version: Enable Timestamp capture for a specific version of the IEEE 802.1AS specification. This field may be programmed to any value between 1 and 15 and allows support for future versions of the IEEE 802.1AS specification.A value of 0 will disable version checking (not recommended). |
| 0 | Receive Timestamp Enable | R/W | 0h | Receive Timestamp Enable: Enable Timestamp capture for Receive. |
PTP_RXCFG1 is shown in Figure 8-120 and described in Table 8-124.
Return to the Summary Table.
This register provides data and mask fields to filter the first byte in a
PTP Message. This function will be disabled if all the mask bits are set to
0.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Receive Byte0 Mask | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Receive Byte0 Data | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | Receive Byte0 Mask | R/W | 0h | Byte0 Mask: Bit mask to be used for matching Byte0 of the Receive PTP Message. A one in any bit enables matching for the associated data bit.If no matching is required, all bits of the mask should be set to 0. |
| 7-0 | Receive Byte0 Data | R/W | 0h | Byte0 Data: Data to be used for matching Byte0 of the Receive PTP Message. |
PTP_RXCFG2 is shown in Figure 8-121 and described in Table 8-125.
Return to the Summary Table.
This register provides for programming an IP address to be used for
filtering packets to detect PTP Event Messages. Since the IPv4 address is
32-bits, to write an IP address, software must write two 16-bit values. The
USER_IP_SEL bit in the PTP_RXCFG0 register selects which octect of the IP
address are accessible through this register.
For example, to write an IP address of
224.0.1.129, software should do the following:
1. Set USER_IP_SEL bit in PTP_RXCFG0 register
to 0
2. Write 0xE000 (224.00) to PTP_RXCFG2
3. Set USER_IP_SEL bit in the PTP_RXCFG0
register to 1
4. Write 0x0181 (01.129) to PTP_RXCFG2
Reading this registerwill return the IP
address field selected by USER_IP_SEL.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Receive IP Address Data | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Receive IP Address Data | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Receive IP Address Data | R/W | 0h | Receive IP Address Data: 16-bits of the IP Address field to be read or written. The 'IP Address Data Select' bit in the PTP_RXCFG0 Register selects the portion of the IP address is to be read or written. - 'IP Address Data Select' in RX_CFG0 == 0 -> set MSB 2 bytes of IPv4/IPv6 Addr in PTP_RXCFG2 register in the normal byte format. - 'IP Address Data Select' in RX_CFG0 == 1 -> set LSB 2 bytes of IPv4/IPv6 Address in PTP_RXCFG2 register in the normal byte format. When IPv4, the complete ip address can be set, when IPv6 only MSB 2 bytes of the 16 byte address and LSB 2 bytes of the 16 byte address are compared. |
PTP_RXCFG3 is shown in Figure 8-122 and described in Table 8-126.
Return to the Summary Table.
This register provides extended configuration for IEEE 802.1AS Receive
Timestamp operation.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RX Minimum IFG after Timestamp | Timestamp on Checksum Error | Timestamp on CRC Error | Append Timestamp | Insert Timestamp | |||
| R/W-Ch | R/W-0h | R/W-0h | R/W-0h | R/W-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Domain Matching Value | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-12 | RX Minimum IFG after Timestamp | R/W | Ch | Minimum Inter-frame Gap: When a Timestamp is appended to a PTP Message, the length of the packet may get extended. This could reduce the Inter-frame Gap (IFG) between packets by as much as 8-byte times (6400ns at 10Mb, 640ns at 100Mb, 64ns at 1G). This field sets a minimum on the IFG between packets in number of byte times. If the IFG is set larger than the actual IFG, Preamble bytes of the subsequent packet will get dropped. This value should be set to the lowest possible value that the attached MAC can support. |
| 11 | Timestamp on Checksum Error | R/W | 0h | Record Timestamp if UDP Checksum
Error: By default, Timestamps will be discarded for packets with UDP Checksum errors. If this bit is set, the Timestamp will be made available in the normal manner. |
| 10 | Timestamp on CRC Error | R/W | 0h | Record Timestamp if CRC Error: By default, Timestamps will be discarded for packets with CRC errors. If this bit is set, the Timestamp will be made available in the normal manner. |
| 9 | Append Timestamp | R/W | 0h | Enable Timestamp append for L2: For Layer 2 encapsulated PTP messages, if this bit is set, always append the Timestamp to end of the PTP message rather than inserted in unused message fields. This bit will be ignored if 'Insert Timestamp' is 0. In case of a CRF, this bit along with 0xD80[10] has to be set to 1 to append timestamp at the end of L2 CRF messgage. UDP packets has to be received with 10 extra bytes padded after CRF data samples for inserting 802.1AS timestamp (8-bytes) and UDP correction word (2-bytes). |
| 8 | Insert Timestamp | R/W | 0h | Enable Timestamp Insertion: Enables Timestamp insertion into a packet containing a PTP Event Message. If this bit is set, the Timestamp will not be available through the PTP Receive Timestamp Register. |
| 7-0 | PTP Domain Matching Value | R/W | 0h | PTP Domain Value: Value of the PTP Message domainNumber field. If PTP_RXCFG0:DOMAIN_EN is set to 1, the Receive Timestamp unit will only capture a Timestamp if the domainNumber in the receive PTP message matches the value in this field.If the DOMAIN_EN bit is set to 0, the domainNumber field will be ignored. |
PTP_RXCFG4 is shown in Figure 8-123 and described in Table 8-127.
Return to the Summary Table.
This register provides extended configuration for IEEE 802.1AS Receive
Timestamp operation. Timestamp insertion should be disabled using (via
PTP_RXCFG3[8]) prior to changing any of the fields in this register.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| IPV4 UDP Checksum Modify | Seconds Timestamp Enable | Seconds Timestamp Length | RX Timestamp nsec Field Offset | ||||
| R/W-0h | R/W-0h | R/W-0h | R/W-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RX Timestamp nsec Field Offset | RX Timestamp sec Field Offset | ||||||
| R/W-0h | R/W-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | IPV4 UDP Checksum Modify | R/W | 0h | Enable IPV4 UDP modification: When timestamp insertion is enabled, this bit controls how UDP checksums are handled for IPV4 PTP event messages. If set to a 0, the device will clear the UDP checksum. If a UDP checksum error is detected the device will force a CRC error. If set to a 1, the device will not clear the UDP checksum. Instead it will generate a 2-byte value to correct the UDP checksum and append this immediately following the PTP message. If an incoming UDP checksum error is detected, the device will cause a UDP checksum error in the modified field. This function should only be used if the incoming packets contain two extra bytes of UDP data following the PTP message. This should not be enabled for systems using version 1 of the IEEE 802.1AS specification. |
| 14 | Seconds Timestamp Enable | R/W | 0h | Enable Timestamp Seconds: Setting this bit to a 1 enables inserting a seconds field when Timestamp Insertion is enabled. If set to 0, only the nanoseconds portion of the Timestamp will be inserted in the packet. This bit will be ignored if 'Insert Timestamp' is 0. This bit is applicable for insertion of timestamps into both PTP and CRF packets. |
| 13-12 | Seconds Timestamp Length | R/W | 0h | Inserted Timestamp Seconds Length: For a PTP message, this field indicates the length of the Seconds field to be inserted in the PTP message. This field will be ignored if 'Insert Timestamp' is 0 or if TS_SEC_EN is 0. For a CRF packet, this field indicates the length of the seconds field to be inserted in the CRF message.This field will be ignored if mr_crf_ts_attach is 0 or if 'Seconds Timestamp Enable' is 0.
|
| 11-6 | RX Timestamp nsec Field Offset | R/W | 0h | Receive Timestamp Nanoseconds
offset: This field provides an offset to the Nanoseconds field when inserting a Timestamp into a received PTP message. If 'Append Timestamp' is set to 1, the offset indicates the offset prior to the end of the PTP message. If 'Append Timestamp' is set to 0, the offset indicates the byte offset from the beginning of the PTP message. This field will be ignored if 'Insert Timestamp' is 0. |
| 5-0 | RX Timestamp sec Field Offset | R/W | 0h | Receive Timestamp Seconds offset: This field provides an offset to the Seconds field when inserting a Timestamp into a received PTP message. If 'Append Timestamp' is set to 1, the offset indicates the offset prior to the end of the inserted Nanoseconds field. If 'Append Timestamp' is set to 0, the offset indicates the byte offset from the beginning of the PTP message.This field will be ignored if 'Insert Timestamp' is 0. |
PTP_TRDL is shown in Figure 8-124 and described in Table 8-128.
Return to the Summary Table.
This register contains the low 16-bits of the duration in clock cycles to
use the Temporary Rate as programmed in the PTP_RATEH and PTP_RATEL
registers. Since the Temporary Rate takes affect upon writing the PTP_RATEL
register, this register should be programmed before setting the Temporary
Rate. This register does not need to be reprogrammed for each use of the
Temporary Rate registers.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Temporary Rate Duration [15:10] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Temporary Rate Duration [15:10] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Temporary Rate Duration [15:10] | R/W | 0h | PTP Temporary Rate Duration Low
16-bits: This register sets the duration for the Temporary Rate in number of clock cycles. The actual Time duration is dependent on the value of the Temporary Rate. |
PTP_TRDH is shown in Figure 8-125 and described in Table 8-129.
Return to the Summary Table.
This register contains the high 10-bits of the duration in clock cycles to
use the Temporary Rate as programmed in the PTP_RATEH and PTP_RATEL
registers. Since the Temporary Rate takes affect upon writing the PTP_RATEL
register, this register should be programmed before setting the Temporary
Rate. This register does not need to be reprogrammed for each use of the
Temporary Rate registers.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Temporary Rate Duration [25:16] | ||||||
| R-0h | R/W-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Temporary Rate Duration [25:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-10 | RESERVED | R | 0h | Reserved |
| 9-0 | Temporary Rate Duration [25:16] | R/W | 0h | PTP Temporary Rate Duration High
10-bits: This register sets the duration for the Temporary Rate in number of clock cycles. The actual Time duration is dependent on the value of the Temporary Rate. |
PTP_EVNT_TSU_CFG is shown in Figure 8-126 and described in Table 8-130.
Return to the Summary Table.
This register provides configuration of storage of Event Timestamps and the transmission to Host using PSF
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Full Event Timestamp Storage Enable | ||||||
| R-0h | R/W-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-1 | RESERVED | R | 0h | Reserved |
| 0 | Full Event Timestamp Storage Enable | R/W | 0h | 1b = Enable storing of full timestamp for events independent of the change from the previous event timestamp |
PTP_COC is shown in Figure 8-127 and described in Table 8-131.
Return to the Summary Table.
This register provides configuration for the PTP clock-synchronized output
divide-by-N clock.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Clock Output Division Value | |||||||
| R/W-Ah | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | RESERVED | R | 0h | Reserved |
| 7-0 | PTP Clock Output Division Value | R/W | Ah | PTP Clock output Divide-by Value: This field sets the divide-by value for the 802.1AS sync output clock. The 802.1AS sync clock output is derived by dividing output clock of PTP_PLL PTP_PLL. Valid values range from 2 to 255 (0x02 to 0xFF), giving a nominal output frequency range of 125MHz down to 980.4kHz. Divide-by values of 0 and 1 are not valid and will stop the output clock. |
PSF_CFG1 is shown in Figure 8-128 and described in Table 8-132.
Return to the Summary Table.
This register provides configuration for the Phy Status Frame function.
Specifically, the 16-bit value in this register is used as the first 16-bits
of the PTP Header data for the Phy Status Frame.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | PTP Version Field | ||||||
| R-0h | R/W-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP TransportSpecific Field | PTP Message Type Field | ||||||
| R/W-0h | R/W-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-12 | RESERVED | R | 0h | PTP v2 reserved field: This field contains the reserved 4-bit field (at offset 1) to be sent in status packets from the Phy to the local MAC using the MII receive data interface. |
| 11-8 | PTP Version Field | R/W | 0h | PTP v2 versionPTP field: This field contains the versionPTP field to be sent in status packets from the Phy to the local MAC using the MII receive data interface. |
| 7-4 | PTP TransportSpecific Field | R/W | 0h | PTP v2 Header transportSpecific
field: This field contains the transportSpecific field to be sent in status packets from the Phy to the local MAC using the MII receive data interface. |
| 3-0 | PTP Message Type Field | R/W | 0h | PTP v2 messageType field: This field contains the messageType field to be sent in status packets from the Phy to the local MAC using the MII receive data interface. |
PSF_CFG2 is shown in Figure 8-129 and described in Table 8-133.
Return to the Summary Table.
This register provides configuration for the Phy Status Frame function.
Specifically, the 16-bit value in this register is used as the first 16-bits
of the IP Source address for an IPv4 Phy Status Frame.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| IP Source Address 1 | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| IP Source Address 0 | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | IP Source Address 1 | R/W | 0h | Second byte of IP source address: This field contains the second byte of the IP source address. |
| 7-0 | IP Source Address 0 | R/W | 0h | First byte of IP source address: This field contains the most significant byte of the IP source address. |
PSF_CFG3 is shown in Figure 8-130 and described in Table 8-134.
Return to the Summary Table.
This register provides configuration for the Phy Status Frame function.
Specifically, the 16-bit value in this register is used as the second
16-bits of the IP Source address for an IPv4 Phy Status Frame.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| IP Source Address 3 | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| IP Source Address 2 | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | IP Source Address 3 | R/W | 0h | Fourth byte of IP source address: This field contains the fourth byte of the IP source address. |
| 7-0 | IP Source Address 2 | R/W | 0h | Third byte of IP source address: This field contains the third byte of the IP source address. |
PSF_CFG4 is shown in Figure 8-131 and described in Table 8-135.
Return to the Summary Table.
This register provides configuration for the Phy Status Frame function.
Specifically, the 16-bit value in this register is used to assist in
computation of the IP checksum for an IPv4 Phy Status Frame.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| IP Checksum | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| IP Checksum | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | IP Checksum | R/W | 0h | IP Checksum: This field contains a precomputed value of ones-complement addition of all fixed values in the IP Header. The device will add the Total Length and Identification values to generate the final checksum. |
PTP_INTCTL is shown in Figure 8-132 and described in Table 8-136.
Return to the Summary Table.
This register provides configuration for the IEEE 802.1AS interrupt
function, allowing the PTP Interrupt to use any of the GPIO pins.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | PTP Interrupt GPIO Select | ||||||
| R-0h | R/W-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-4 | RESERVED | R | 0h | Reserved |
| 3-0 | PTP Interrupt GPIO Select | R/W | 0h | PTP Interrupt GPIO select: To enable interrupts on a GPIO pin, this field should be set to the required GPIO.
|
PTP_CLKSRC is shown in Figure 8-133 and described in Table 8-137.
Return to the Summary Table.
This register provides configuration for the reference clock source
driving the IEEE 802.1AS hardware logic. The source clock period is also
used by the 802.1AS nanoseconds clock adder to add the proper value every
reference clock cycle.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Clock Reference Select-1 | PTP Ref Clock Division Enable | PTP Clock Reference Select-2 | PTP Ref Clock Division Value | ||||
| R/W-0h | R/W-0h | R/W-0h | R/W-1h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Ref Clock Division Value | PTP Clock Source Period | ||||||
| R/W-1h | R/W-4h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-14 | PTP Clock Reference Select-1 | R/W | 0h | PTP Clock Source Select: Selects among possible sources for the PTP reference clock Mapping of {PTP Clock Reference Select-1, PTP Clock Reference Select-2} is as follows: b1000 : Reserved b1010 : Reserved b0000 : PLL 250M (not available in RMII Follower Mode) b0100 : PLL 125M (not available in RMII Follower Mode) b0010 : Clock from PTP_PLL (not available in RMII Follower Mode) b0001 : Recovered 200M b0101 : Recovered 100M |
| 13 | PTP Ref Clock Division Enable | R/W | 0h | Clock division enable: If set to 1, enables division of the PTP reference clock by a factor of value programmed in CLK_DIV_VAL. |
| 12-11 | PTP Clock Reference Select-2 | R/W | 0h | PTP Clock Source Select: Selects among possible sources for the PTP reference clock Mapping of {PTP Clock Reference Select-1, PTP Clock Reference Select-2} is as follows: b1000 : Reserved b1010 : Reserved b0000 : PLL 250M (not available in RMII Follower Mode) b0100 : PLL 125M (not available in RMII Follower Mode) b0010 : Clock from PTP_PLL (not available in RMII Follower Mode) b0001 : Recovered 200M b0101 : Recovered 100M |
| 10-7 | PTP Ref Clock Division Value | R/W | 1h | Clock division divider value: When the clock source selection is the Divide-by-N using 'PTP Ref Clock Division Enable', these bits are used as the N value. |
| 6-0 | PTP Clock Source Period | R/W | 4h | PTP Clock Source Period: This field configures the PTP clock source period in nanoseconds. Program the clock source period as > 2 |
PTP_ETYPE is shown in Figure 8-134 and described in Table 8-138.
Return to the Summary Table.
This register provides the Ethernet Type (Ethertype) field for PTP
transport over Ethernet (Layer2).
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP EtherType | |||||||
| R/W-F788h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP EtherType | |||||||
| R/W-F788h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP EtherType | R/W | F788h | PTP EtherType: This field contains the Ethernet Type field used to detect PTP messages transported over Ethernet layer 2. Program this register in reverse byte format. For example, the ethertype expected from PTP packets is 0x88F7 so 0xF788 is made as default value. |
PTP_OFF is shown in Figure 8-135 and described in Table 8-139.
Return to the Summary Table.
This register provides the byte offset to the PTP message in a Layer2
Ethernet frame.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Message Field Offset | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-8 | RESERVED | R | 0h | Reserved |
| 7-0 | PTP Message Field Offset | R/W | 0h | PTP Message Offset: This field contains the offset in bytes to the PTP Message from the preceding header. For Layer2, this is the offset from the Ethernet Type Field. For UDP/IP, it is the offset from the end of the UDP Header. |
PTP_RXHASH is shown in Figure 8-136 and described in Table 8-140.
Return to the Summary Table.
This register provides configuration for the source identity hash filter
of the PTP receive packet parser. If enabled, the receive parse logic will
deliver a receive timestamp only if the hash function on the ten octet
sourcePortIdentity field correctly matches the programmed value. The source
identity hash filter does not affect timestamp insertion.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Receive Hash Enable | Receive Hash | |||||
| R-0h | R/W-0h | R/W-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Receive Hash | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-13 | RESERVED | R | 0h | Reserved |
| 12 | Receive Hash Enable | R/W | 0h | Receive Hash Enable: Enables filtering of PTP messages based on the hash function on the ten octet sourcePortIdentity field. |
| 11-0 | Receive Hash | R/W | 0h | Receive Hash: This field contains the expected source identity hash value for incoming PTP event messages. |
PTP_EVENT_GPIO_SEL is shown in Figure 8-137 and described in Table 8-141.
Return to the Summary Table.
This register provides controls to make which IOs as inputs to enable
event timestamping on them.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | GPIO Event Enable | ||||||
| R-0h | R/W-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-5 | RESERVED | R | 0h | Reserved |
| 4-0 | GPIO Event Enable | R/W | 0h | GPIO Enable for PTP Event timestamping: Writing to these registers enables GPIOs for event timestamping by making them inputs Bit[0] = 1 : Reserved Bit[1] = 1 : LED_1 is set as input Bit[2] = 1 : RX_ER is set as input Bit[3] = 1 : CLKOUT is set as input Bit[4] = 1 : Reserved Bit[5] = 1 : Reserved Bit[6] = 1 : Reserved |
TX_SMD_GPIO_CTL is shown in Figure 8-138 and described in Table 8-142.
Return to the Summary Table.
This register controls Start mPacket Delimiter (SMD) detection on TX path
and GPIO configurtion for indicating the TX_SMD.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Dual VLAN Tag Parse Enable | RESERVED | RESERVED | RESERVED | ||||
| R/W-0h | R-0h | R-0h | R-0h | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | Dual VLAN Tag Parse Enable | R/W | 0h | 1b = Enable parsing of received packets with Dual VLAN tag |
| 14 | RESERVED | R | 0h | Reserved |
| 13-9 | RESERVED | R | 0h | Reserved |
| 8-5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3-0 | RESERVED | R | 0h | Reserved |
SCH_CTL_1 is shown in Figure 8-139 and described in Table 8-143.
Return to the Summary Table.
Contains LSB 16-bits of step rate used by scheduler for scheduling large
PPM adjustments.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Scheduler Step Rate [15:0] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Scheduler Step Rate [15:0] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Scheduler Step Rate [15:0] | R/W | 0h | Scheduler step rate for scheduling
large PPM adjustment lower 16-bits: Bit 15:0 of 24-bit rate step used by scheduler (applicable only during permanent rate change and micro scheduler is used for rate change in small steps), resolution is 2-32 ns. Calculate clock period from mr_base_freq[31:0] and then using desired step rate value in ppm, calculate step rate in ns. Scale the value by 2-32 to obtain value to programmed to mr_step_rate. |
SCH_CTL_2 is shown in Figure 8-140 and described in Table 8-144.
Return to the Summary Table.
Contains MSB 8-bits of step rate used by scheduler for scheduling large
PPM adjustments along with bypass options for PTP_PLL and accumulator.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Bypass Scheduler for PTP PLL | Bypass Scheduler for Timer | |||||
| R-0h | R/W-1h | R/W-1h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Scheduler Step Rate [23:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-10 | RESERVED | R | 0h | Reserved |
| 9 | Bypass Scheduler for PTP PLL | R/W | 1h | Bypass scheduler for PTP_PLL: Bypass scheduler controlled rate going to PTP_PLL (applicable only during permanent rate change). When this Bit is set and Bit 8 is not set, scheduler controlled rate adjustment is applied to the timer but PTP_PLL gets total PTP rate adjustment. When this bit as well as Bit 8 is set, scheduler based adjustment is bypassed. |
| 8 | Bypass Scheduler for Timer | R/W | 1h | Bypass scheduler for Timer: Bypass scheduler controlled rate going to timer (applicable only during permanent rate change). When this Bit is set and Bit 9 is not set, scheduler controlled rate adjustment is applied to PTP_PLL but timer gets total PTP rate adjustment. When this bit as well as Bit 9 is set, scheduler based adjustment is bypassed. |
| 7-0 | Scheduler Step Rate [23:16] | R/W | 0h | Scheduler step rate for scheduling
large PPM adjustment MSB 8-bits: Bit 23:16 of 24-Bit rate step used by scheduler (applicable only during permanent rate change and when micro scheduler is used for rate change in small steps), resolution is 2-32ns. Calculate clock period from mr_base_freq[31:0]. Using desired step rate value in ppm, calculate step rate in ns. Scale the value by 2-32 to obtain value to be programmed to mr_step_rate. |
FREQ_CTL_1 is shown in Figure 8-141 and described in Table 8-145.
Return to the Summary Table.
Contains LSB 16-bits of Base frequency programmable for PTP_PLL.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Base Frequency for PTP_PLL [15:0] | |||||||
| R/W-CCCDh | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Base Frequency for PTP_PLL [15:0] | |||||||
| R/W-CCCDh | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Base Frequency for PTP_PLL [15:0] | R/W | CCCDh | Base frequency programmable for PTP_PLL
LSB word. To enable 245.76MHz PTP_PLL frequency,
set to 0x9B88. Note: Frequency value will be modified only when 0xD35 and 0xD36 are written in sequence. This config decides the default clock frequency for PTP_PLL. |
FREQ_CTL_2 is shown in Figure 8-142 and described in Table 8-146.
Return to the Summary Table.
Contains MSB 16-bits of Base frequency programmable for PTP_PLL.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Base Frequency for PTP_PLL [31:16] | |||||||
| R/W-CCCCh | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Base Frequency for PTP_PLL [31:16] | |||||||
| R/W-CCCCh | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Base Frequency for PTP_PLL [31:16] | R/W | CCCCh | Base frequency programmable for PTP_PLL
MSB word. To enable 245.76MHz PTP_PLL frequency,
set to 0xC953. Note: Frequency value will be modified only when 0xD35 and 0xD36 are written in sequence. This config decides the default clock frequency for PTP_PLL. |
PTP_RATEL_ACC_ONLY is shown in Figure 8-143 and described in Table 8-147.
Return to the Summary Table.
Contains LSB 16 bits of accumulator only rate adjustment value.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Accumulator Rate Control [15:0] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Accumulator Rate Control [15:0] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Accumulator Rate Control [15:0] | R/W | 0h | Rate Control value for PTP
accumulator: Writing to this register will set the bits 15:0 of the Rate Control value for PTP accumulator when 0xD38[14] is set. The Rate Control value is in units of 2-32ns. This rate adjustment will not be applied to PTP_PLL. PTP_PLL rate adjustment will still be controlled from registers 0xD04 and 0xD05. |
PTP_RATEH_ACC_ONLY is shown in Figure 8-144 and described in Table 8-148.
Return to the Summary Table.
Contains MSB 10 bits of accumulator only rate adjustment value. Also
contains enable and direction of accumulator only rate adjustment.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Accumulator Direction | PTP Accumulator Mode Enable | PTP Accumulator Trate Enable | RESERVED | PTP Accumulator Rate Control [25:16] | |||
| R/W-0h | R/W-0h | R/W-0h | R-0h | R/W-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Accumulator Rate Control [25:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | PTP Accumulator Direction | R/W | 0h | PTP Rate ACC only Direction: The setting of this bit controls whether the device will operate at a higher or lower frequency than the reference clock. This direction is applied along with 0xD37 and 0xD38[9:0] only if bit 0xD38[14] is set.
|
| 14 | PTP Accumulator Mode Enable | R/W | 0h | PTP Accumulator mode: Setting this bit will make the PTP accumulator to be incremented according to registers 0xD37 and 0xD38[9:0] every clock cycle.
|
| 13 | PTP Accumulator Trate Enable | R/W | 0h | PTP Temporary Rate Enable in
Accumulator Mode: Setting this bit will apply the temporary rate adjustments to the PTP Accumulator too (apart from the PTP PLL)
|
| 12-10 | RESERVED | R | 0h | Reserved |
| 9-0 | PTP Accumulator Rate Control [25:16] | R/W | 0h | PTP Rate ACC only high 10-bits: Writing to this register will set the bits 25:16 of the Rate Control value for PTP accumulator when 0xD38[14] is set. The Rate Control value is in units of 2-32ns. This rate adjustment will not be applied to PTP_PLL. PTP_PLL rate adjustment will still be controlled from registers 0xD04 and 0xD05. |
PTP_PLL_CTL is shown in Figure 8-145 and described in Table 8-149.
Return to the Summary Table.
Register to configure PTP_PLL settiling time and enables storing of PTP
timestamp.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Half Rate Enable | PTP PLL Phase word [32] | |||||
| R-0h | R-0h | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Capture PTP Time | PTP Scheduler Settle Timer | ||||||
| R/W-0h | R/W-25h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-10 | RESERVED | R | 0h | Reserved |
| 9 | Half Rate Enable | R | 0h | PTP_PLL set half rate: Set half rate for the NCO when in PLL_125M as ref clock mode. |
| 8 | PTP PLL Phase word [32] | R | 0h | PTP_PLL phase word bit-32: Bit 32 of PTP_PLL phase word |
| 7 | Capture PTP Time | R/W | 0h | Capture PTP time and PTP_PLL word: Used to capture the current 33-bit PTP_PLL word along with 64-bit PTP time. Setting this trigger stores PTP clock timestamp (32-bit seconds accumulator, 32-bit nsec accumulator ) and 33-bit PTP_PLL word simultaneously which can be read through 0xD39 - 0xD3F. This bit is self clearing. . |
| 6-0 | PTP Scheduler Settle Timer | R/W | 25h | PTP_PLL scheduler settle timer: No of cycles taken by PTP_PLL to provide jitter free output for any change in rate, defines the latency of rate change going to PTP_PLL. Used in scheduler every time thevalue of the PTP_PLL is changed. |
PTP_PLL_RD_1 is shown in Figure 8-146 and described in Table 8-150.
Return to the Summary Table.
PTP timer nanosec counter readout value.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Timestamp [15:0] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Timestamp [15:0] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Timestamp [15:0] | R | 0h | PTP time nano seconds LSB word: Bit 15 - 0 of PTP timer nano seconds counter. |
PTP_PLL_RD_2 is shown in Figure 8-147 and described in Table 8-151.
Return to the Summary Table.
PTP timer nanosec counter readout value.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Timestamp [31:16] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Timestamp [31:16] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Timestamp [31:16] | R | 0h | PTP time nano seconds MSB word: Bit 31 - 16 of PTP timer nano seconds counter. |
PTP_PLL_RD_3 is shown in Figure 8-148 and described in Table 8-152.
Return to the Summary Table.
PTP timer seconds counter readout value.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Timestamp [47:32] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Timestamp [47:32] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Timestamp [47:32] | R | 0h | PTP time seconds LSB word: Bit 15 - 0 of PTP timer seconds counter. |
PTP_PLL_RD_4 is shown in Figure 8-149 and described in Table 8-153.
Return to the Summary Table.
PTP timer seconds counter readout value.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Timestamp [63:48] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Timestamp [63:48] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Timestamp [63:48] | R | 0h | PTP time seconds MSB word: Bit 31 - 16 of PTP timer seconds counter. |
PTP_PLL_RD_5 is shown in Figure 8-150 and described in Table 8-154.
Return to the Summary Table.
PTP_PLL phase word read out value.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Timestamp [79:64] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Timestamp [79:64] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Timestamp [79:64] | R | 0h | PTP_PLL phase LSB word: Bit 15 - 0 of PTP_PLL phase word. |
PTP_PLL_RD_6 is shown in Figure 8-151 and described in Table 8-155.
Return to the Summary Table.
PTP_PLL phase word read out value.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Timestamp [95:80] | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP Timestamp [95:80] | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | PTP Timestamp [95:80] | R | 0h | PTP_PLL phase MSB word: Bit 31 - 16 of PTP_PLL phase word. |
PTP_ONESTEP_OFF is shown in Figure 8-152 and described in Table 8-156.
Return to the Summary Table.
Controls offset value of onestep timestamp being inserted into the PTP
packet.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PTP Accumulator Rate Control [31:26] | PTP One-step Timestamp Offset Addition Enable | PTP One-step Timestamp Offset | |||||
| R/W-0h | R/W-0h | R/W-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| PTP One-step Timestamp Offset | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-10 | PTP Accumulator Rate Control [31:26] | R/W | 0h | PTP accumulator Rate Control value: Writing to this register sets bits 31:26 of the Rate Control value for PTP accumulator only when 0xD38[14] is set. The Rate Control value is in units of 2-32ns. This rate adjustment will not be applied to PTP_PLL. PTP_PLL rate adjustment will still be controlled from registers 0xD04 and 0xD05. |
| 9 | PTP One-step Timestamp Offset Addition Enable | R/W | 0h | PTP one-step timestamp offset addition
enable: Setting this bit enables addition of the offset (loaded in 0xD40[8:0]) to the timestamp being inserted into the PTP packet during one-step timestamp insertion |
| 8-0 | PTP One-step Timestamp Offset | R/W | 0h | PTP one-step timestamp offset: This offset value is added to the timestamp that is being inserted during one-step operation when 0xD40[9] is enabled. |
PTP_PLL_FORCE_CTRL_1 is shown in Figure 8-153 and described in Table 8-157.
Return to the Summary Table.
Force controls for PTP_PLL A2D boundary signals.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Frequency Word Force Value [15:0] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Frequency Word Force Value [15:0] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Frequency Word Force Value [15:0] | R/W | 0h | PTP_PLL freq word force value: Bit 15 - 0 of freq word force value, valid when 0xD43[1] is set. |
PTP_PLL_FORCE_CTRL_2 is shown in Figure 8-154 and described in Table 8-158.
Return to the Summary Table.
Force controls for PTP_PLL A2D boundary signals.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Frequency Word Force Value [31:16] | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| Frequency Word Force Value [31:16] | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | Frequency Word Force Value [31:16] | R/W | 0h | PLL freq word force value: Bit 31 - 16 of freq word force value, valid when 0xD43[1] is set. |
PTP_PLL_FORCE_CTRL_3 is shown in Figure 8-155 and described in Table 8-159.
Return to the Summary Table.
Force controls for PTP_PLL A2D boundary signals.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | RESERVED | Frequency Word Force Enable | Frequency Word Force Value [32] | |||
| R-0h | R-0h | R-0h | R/W-0h | R/W-0h | |||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-4 | RESERVED | R | 0h | Reserved |
| 3 | RESERVED | R | 0h | Reserved |
| 2 | RESERVED | R | 0h | Reserved |
| 1 | Frequency Word Force Enable | R/W | 0h | PTP_PLL freq word force: When set, freq word in the register 0xD41,0xD42,0xD43[0] is written to the PTP_PLL. |
| 0 | Frequency Word Force Value [32] | R/W | 0h | PTP_PLL freq word force value: Bit 32 of freq word force value, valid when 0xD43[1] is set. |
PTP_PSF_VLAN_CFG_1 is shown in Figure 8-156 and described in Table 8-160.
Return to the Summary Table.
Configuration of VLAN tags for PSF packets
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Dual VLAN Tag Enable for PSF | VLAN Tag Enable for PSF | |||||
| R-0h | R/W-0h | R/W-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-2 | RESERVED | R | 0h | Reserved |
| 1 | Dual VLAN Tag Enable for PSF | R/W | 0h | 1b = Enable addition of dual VLAN tag for PSF packets |
| 0 | VLAN Tag Enable for PSF | R/W | 0h | 1b = Enable addition of VLAN tag for PSF packet |
PTP_PSF_VLAN_CFG_2 is shown in Figure 8-157 and described in Table 8-161.
Return to the Summary Table.
Configuration of VLAN tags for PSF packets
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| VLAN Tag 1 for PSF | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| VLAN Tag 1 for PSF | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | VLAN Tag 1 for PSF | R/W | 0h | VLAN Tag 1 added to PSF packets when 0x0D45[0]=1 |
PTP_PSF_VLAN_CFG_3 is shown in Figure 8-158 and described in Table 8-162.
Return to the Summary Table.
Configuration of VLAN tags for PSF packets
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| VLAN Tag 2 for PSF | |||||||
| R/W-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| VLAN Tag 2 for PSF | |||||||
| R/W-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-0 | VLAN Tag 2 for PSF | R/W | 0h | VLAN Tag 2 added to PSF packets when 0x0D45[1]=1 |
PTP_LAT_COMP_CTRL is shown in Figure 8-159 and described in Table 8-163.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | Dithering Latency Compensation Enable - Receive path | Dithering Latency Compensation Enable - Transmit path | Latency Compensation Enable - Receive path | Latency Compensation Enable - Transmit path | ||
| R-0h | R-0h | R/W-0h | R/W-0h | R/W-0h | R/W-0h | ||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-5 | RESERVED | R | 0h | Reserved |
| 4 | RESERVED | R | 0h | Reserved |
| 3 | Dithering Latency Compensation Enable - Receive path | R/W | 0h | Enable fixed latency compensation on the Rx side, when dithering is enabled, for 2-step PTP time stamping |
| 2 | Dithering Latency Compensation Enable - Transmit path | R/W | 0h | Enable fixed latency compensation on the Tx side, when dithering is enabled, for 2-step PTP time stamping |
| 1 | Latency Compensation Enable - Receive path | R/W | 0h | Enable fixed latency compensation on the Rx side, for 2-step PTP time stamping |
| 0 | Latency Compensation Enable - Transmit path | R/W | 0h | Enable fixed latency compensation on the Tx side, for 2-step PTP time stamping |
PTP_DEBUG_SEL is shown in Figure 8-160 and described in Table 8-164.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | RESERVED | PTP External Reference Support Enable | |||||
| R-0h | R-0h | R/W-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-2 | RESERVED | R | 0h | Reserved |
| 1 | RESERVED | R | 0h | Reserved |
| 0 | PTP External Reference Support Enable | R/W | 0h | In PTP external reference clock mode, by default the minimum frequency supported is >35 MHz, to support lower frequencies (upto 25MHz), this bit should be set |
MMD1_PMA_CTRL_1 is shown in Figure 8-161 and described in Table 8-165.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PMA Reset | RESERVED | ||||||
| R/W-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | PMA Loopback | ||||||
| R-0h | R/W-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | PMA Reset | R/W | 0h | 1b = PMA reset |
| 14-1 | RESERVED | R | 0h | Reserved |
| 0 | PMA Loopback | R/W | 0h | 1b = PMA loopback set |
MMD1_PMA_STATUS_1 is shown in Figure 8-162 and described in Table 8-166.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | Link Status | RESERVED | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-3 | RESERVED | R | 0h | Reserved |
| 2 | Link Status | R | 0h | 1b = Link is up |
| 1-0 | RESERVED | R | 0h | Reserved |
MMD1_PMA_STAUS_2 is shown in Figure 8-163 and described in Table 8-167.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | PMA PMD Type Selection | ||||||
| R-0h | R-3Dh | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-6 | RESERVED | R | 0h | Reserved |
| 5-0 | PMA PMD Type Selection | R | 3Dh | PMA or PMD type selection field 111101b = 100BASE-T1 PMA or PMD |
MMD1_PMA_EXT_ABILITY_1 is shown in Figure 8-164 and described in Table 8-168.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Extended Abilities | RESERVED | |||||
| R-0h | R-1h | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-12 | RESERVED | R | 0h | Reserved |
| 11 | Extended Abilities | R | 1h | 1b = PMA/PMD has BASE-T1 extended
abilities 0b = PMA/PMD does not have BASE-T1 extended abilities |
| 10-0 | RESERVED | R | 0h | Reserved |
MMD1_PMA_EXT_ABILITY_2 is shown in Figure 8-165 and described in Table 8-169.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | |||||||
| R-0h | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | 100BASE-T1 Ability | ||||||
| R-0h | R-1h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-1 | RESERVED | R | 0h | Reserved |
| 0 | 100BASE-T1 Ability | R | 1h | 1b = PMA/PMD supports 100BASE-T1 0b = PMA/PMD doesn't support 100BASE-T1 |
MMD1_PMA_CTRL_2 is shown in Figure 8-166 and described in Table 8-170.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | Leader Follower Configuration | RESERVED | |||||
| R-0h | R/W-Xh | R-0h | |||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | type selection | ||||||
| R-0h | R-0h | ||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | RESERVED | R | 0h | Reserved |
| 14 | Leader Follower Configuration | R/W | 0h | 1b = Configure PHY as LEADER 0b = Configure PHY as FOLLOWER |
| 13-4 | RESERVED | R | 0h | Reserved |
| 3-0 | type selection | R | 0h | type selection field 0000b = 100Base-T1 |
MMD1_PMA_TEST_MODE_CTRL is shown in Figure 8-167 and described in Table 8-171.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| Compliance Test Mode | RESERVED | ||||||
| R/W-0h | R-0h | ||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-13 | Compliance Test Mode | R/W | 0h | 100BASE-T1 test mode control 000b = Normal mode operation 001b = Test mode 1 010b = Test mode 2 011b = Reserved 100b = Test mode 4 101b = Test mode 5 110b = Reserved 111b = Reserved |
| 12-0 | RESERVED | R | 0h | Reserved |
MMD3_PCS_CTRL_1 is shown in Figure 8-168 and described in Table 8-172.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| PCS Reset | PCS Loopback | RESERVED | RX Clock Stoppable | RESERVED | |||
| R/W-0h | R/W-0h | R-0h | R/W-0h | R-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | |||||||
| R-0h | |||||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15 | PCS Reset | R/W | 0h | Reset bit, Self Clear. When write to this bit 1: 1. reset the registers (not vendor specific) at MMD3/MMD7. 2. Reset brk_top Please notice: This register is WSC (write-self-clear) and not read-only! |
| 14 | PCS Loopback | R/W | 0h | This bit is cleared by PCS_Reset |
| 13-11 | RESERVED | R | 0h | Reserved |
| 10 | RX Clock Stoppable | R/W | 0h | RW, reset value = 1. 1= PHY may stop receive clock during LPI 0= Clock not stoppable Note: this flop implemented at glue logic |
| 9-0 | RESERVED | R | 0h | Reserved |
MMD3_PCS_Status_1 is shown in Figure 8-169 and described in Table 8-173.
Return to the Summary Table.
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 |
| RESERVED | TX LPI Received | RX LPI Received | TX LPI Indication | RX LPI Indication | |||
| R-0h | RC-0h | RC-0h | R-0h | R-0h | |||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| RESERVED | TX Clock Stoppable | RESERVED | |||||
| R-0h | R-0h | R-0h | |||||
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 15-12 | RESERVED | R | 0h | Reserved |
| 11 | TX LPI Received | RC | 0h | 1= Tx PCS hs received LPI 0= LPI not received |
| 10 | RX LPI Received | RC | 0h | 1= Rx PCS hs received LPI 0= LPI not received |
| 9 | TX LPI Indication | R | 0h | 1= TX PCS is currently receiving LPI 0= PCS is not currently receiving LPI |
| 8 | RX LPI Indication | R | 0h | 1= RX PCS is currently receiving LPI 0= PCS is not currently receiving LPI |
| 7 | RESERVED | R | 0h | Reserved |
| 6 | TX Clock Stoppable | R | 0h | 1= the MAC may stop the clock during
LPI 0= Clock not stoppable |
| 5-0 | RESERVED | R | 0h | Reserved |