ZHCSHP8B December   2017  – January 2019 AMIC120

PRODUCTION DATA.  

  1. 1器件概述
    1. 1.1 特性
    2. 1.2 应用
    3. 1.3 说明
    4. 1.4 功能方框图
  2. 2修订历史记录
  3. 3Device Comparison
    1. 3.1 Related Products
  4. 4Terminal Configuration and Functions
    1. 4.1 Pin Diagrams
      1. Table 4-1 ZDN Ball Map [Section Top Left - Top View]
      2. Table 4-2 ZDN Ball Map [Section Top Middle - Top View]
      3. Table 4-3 ZDN Ball Map [Section Top Right - Top View]
      4. Table 4-4 ZDN Ball Map [Section Middle Left - Top View]
      5. Table 4-5 ZDN Ball Map [Section Middle Middle - Top View]
      6. Table 4-6 ZDN Ball Map [Section Middle Right - Top View]
      7. Table 4-7 ZDN Ball Map [Section Bottom Left - Top View]
      8. Table 4-8 ZDN Ball Map [Section Bottom Middle - Top View]
      9. Table 4-9 ZDN Ball Map [Section Bottom Right - Top View]
    2. 4.2 Pin Attributes
    3. 4.3 Signal Descriptions
      1. 4.3.1  ADC Interfaces
      2. 4.3.2  CAN Interfaces
      3. 4.3.3  Debug Subsystem Interface
      4. 4.3.4  Ethernet (GEMAC_CPSW) Interfaces
      5. 4.3.5  External Memory Interfaces
      6. 4.3.6  General Purpose IOs
      7. 4.3.7  HDQ Interface
      8. 4.3.8  I2C Interfaces
      9. 4.3.9  McASP Interfaces
      10. 4.3.10 Miscellaneous
      11. 4.3.11 PRU-ICSS0 Interface
      12. 4.3.12 PRU-ICSS1 Interface
      13. 4.3.13 QSPI Interface
      14. 4.3.14 RTC Subsystem Interface
      15. 4.3.15 Removable Media Interfaces
      16. 4.3.16 SPI Interfaces
      17. 4.3.17 Timer Interfaces
      18. 4.3.18 UART Interfaces
      19. 4.3.19 USB Interfaces
      20. 4.3.20 eCAP Interfaces
      21. 4.3.21 eHRPWM Interfaces
      22. 4.3.22 eQEP Interfaces
  5. 5Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Power-On Hours (POH)
    4. 5.4  Operating Performance Points
    5. 5.5  Recommended Operating Conditions
    6. 5.6  Power Consumption Summary
    7. 5.7  DC Electrical Characteristics
    8. 5.8  ADC0: Analog-to-Digital Subsystem Electrical Parameters
    9. 5.9  Thermal Resistance Characteristics
      1. Table 5-6 Thermal Resistance Characteristics (NFBGA Package) [ZDN]
    10. 5.10 External Capacitors
      1. 5.10.1 Voltage Decoupling Capacitors
        1. 5.10.1.1 Core Voltage Decoupling Capacitors
        2. 5.10.1.2 IO and Analog Voltage Decoupling Capacitors
      2. 5.10.2 Output Capacitors
    11. 5.11 Timing and Switching Characteristics
      1. 5.11.1  Power Supply Sequencing
        1. 5.11.1.1 Power Supply Slew Rate Requirement
        2. 5.11.1.2 Power-Up Sequencing
        3. 5.11.1.3 Power-Down Sequencing
      2. 5.11.2  Clock
        1. 5.11.2.1 PLLs
          1. 5.11.2.1.1 Digital Phase-Locked Loop Power Supply Requirements
        2. 5.11.2.2 Input Clock Specifications
        3. 5.11.2.3 Input Clock Requirements
          1. 5.11.2.3.1 OSC0 Internal Oscillator Clock Source
            1. Table 5-11 OSC0 Crystal Circuit Requirements
            2. Table 5-12 OSC0 Crystal Circuit Characteristics
          2. 5.11.2.3.2 OSC0 LVCMOS Digital Clock Source
          3. 5.11.2.3.3 OSC1 Internal Oscillator Clock Source
            1. Table 5-14 OSC1 Crystal Circuit Requirements
            2. Table 5-15 OSC1 Crystal Circuit Characteristics
          4. 5.11.2.3.4 OSC1 LVCMOS Digital Clock Source
          5. 5.11.2.3.5 OSC1 Not Used
        4. 5.11.2.4 Output Clock Specifications
        5. 5.11.2.5 Output Clock Characteristics
          1. 5.11.2.5.1 CLKOUT1
          2. 5.11.2.5.2 CLKOUT2
      3. 5.11.3  Timing Parameters and Board Routing Analysis
      4. 5.11.4  Recommended Clock and Control Signal Transition Behavior
      5. 5.11.5  Controller Area Network (CAN)
        1. 5.11.5.1 DCAN Electrical Data and Timing
          1. Table 5-17 Timing Requirements for DCANx Receive
          2. Table 5-18 Switching Characteristics for DCANx Transmit
      6. 5.11.6  DMTimer
        1. 5.11.6.1 DMTimer Electrical Data and Timing
          1. Table 5-19 Timing Requirements for DMTimer [1-11]
          2. Table 5-20 Switching Characteristics for DMTimer [4-7]
      7. 5.11.7  Ethernet Media Access Controller (EMAC) and Switch
        1. 5.11.7.1 Ethernet MAC and Switch Electrical Data and Timing
          1. Table 5-21 Ethernet MAC and Switch Timing Conditions
          2. 5.11.7.1.1 Ethernet MAC/Switch MDIO Electrical Data and Timing
            1. Table 5-22 Timing Requirements for MDIO_DATA
            2. Table 5-23 Switching Characteristics for MDIO_CLK
            3. Table 5-24 MDIO Switching Characteristics - MDIO_DATA
          3. 5.11.7.1.2 Ethernet MAC and Switch MII Electrical Data and Timing
            1. Table 5-25 Timing Requirements for GMII[x]_RXCLK - MII Mode
            2. Table 5-26 Timing Requirements for GMII[x]_TXCLK - MII Mode
            3. Table 5-27 Timing Requirements for GMII[x]_RXD[3:0], GMII[x]_RXDV, and GMII[x]_RXER - MII Mode
            4. Table 5-28 Switching Characteristics for GMII[x]_TXD[3:0], and GMII[x]_TXEN - MII Mode
          4. 5.11.7.1.3 Ethernet MAC and Switch RMII Electrical Data and Timing
            1. Table 5-29 Timing Requirements for RMII[x]_REFCLK - RMII Mode
            2. Table 5-30 Timing Requirements for RMII[x]_RXD[1:0], RMII[x]_CRS_DV, and RMII[x]_RXER - RMII Mode
            3. Table 5-31 Switching Characteristics for RMII[x]_TXD[1:0], and RMII[x]_TXEN - RMII Mode
          5. 5.11.7.1.4 Ethernet MAC and Switch RGMII Electrical Data and Timing
            1. Table 5-32 Timing Requirements for RGMII[x]_RCLK - RGMII Mode
            2. Table 5-33 Timing Requirements for RGMII[x]_RD[3:0], and RGMII[x]_RCTL - RGMII Mode
            3. Table 5-34 Switching Characteristics for RGMII[x]_TCLK - RGMII Mode
            4. Table 5-35 Switching Characteristics for RGMII[x]_TD[3:0], and RGMII[x]_TCTL - RGMII Mode
      8. 5.11.8  External Memory Interfaces
        1. 5.11.8.1 General-Purpose Memory Controller (GPMC)
          1. 5.11.8.1.1 GPMC and NOR Flash—Synchronous Mode
            1. Table 5-36 GPMC and NOR Flash Timing Conditions—Synchronous Mode
            2. Table 5-37 GPMC and NOR Flash Timing Requirements—Synchronous Mode
            3. Table 5-38 GPMC and NOR Flash Switching Characteristics—Synchronous Mode
          2. 5.11.8.1.2 GPMC and NOR Flash—Asynchronous Mode
            1. Table 5-39 GPMC and NOR Flash Timing Conditions—Asynchronous Mode
            2. Table 5-40 GPMC and NOR Flash Internal Timing Parameters—Asynchronous Mode
            3. Table 5-41 GPMC and NOR Flash Timing Requirements—Asynchronous Mode
            4. Table 5-42 GPMC and NOR Flash Switching Characteristics—Asynchronous Mode
          3. 5.11.8.1.3 GPMC and NAND Flash—Asynchronous Mode
            1. Table 5-43 GPMC and NAND Flash Timing Conditions—Asynchronous Mode
            2. Table 5-44 GPMC and NAND Flash Internal Timing Parameters—Asynchronous Mode
            3. Table 5-45 GPMC and NAND Flash Timing Requirements—Asynchronous Mode
            4. Table 5-46 GPMC and NAND Flash Switching Characteristics—Asynchronous Mode
        2. 5.11.8.2 Memory Interface
          1. 5.11.8.2.1 DDR3 and DDR3L Routing Guidelines
            1. 5.11.8.2.1.1 Board Designs
            2. 5.11.8.2.1.2 DDR3 Device Combinations
            3. 5.11.8.2.1.3 DDR3 Interface
              1. 5.11.8.2.1.3.1  DDR3 Interface Schematic
              2. 5.11.8.2.1.3.2  Compatible JEDEC DDR3 Devices
              3. 5.11.8.2.1.3.3  DDR3 PCB Stackup
              4. 5.11.8.2.1.3.4  DDR3 Placement
              5. 5.11.8.2.1.3.5  DDR3 Keepout Region
              6. 5.11.8.2.1.3.6  DDR3 Bulk Bypass Capacitors
              7. 5.11.8.2.1.3.7  DDR3 High-Speed Bypass Capacitors
                1. 5.11.8.2.1.3.7.1 Return Current Bypass Capacitors
              8. 5.11.8.2.1.3.8  DDR3 Net Classes
              9. 5.11.8.2.1.3.9  DDR3 Signal Termination
              10. 5.11.8.2.1.3.10 DDR3 DDR_VREF Routing
              11. 5.11.8.2.1.3.11 DDR3 VTT
            4. 5.11.8.2.1.4 DDR3 CK and ADDR_CTRL Topologies and Routing Definition
              1. 5.11.8.2.1.4.1 Using Two DDR3 Devices (x8 or x16)
                1. 5.11.8.2.1.4.1.1 CK and ADDR_CTRL Topologies, Two DDR3 Devices
                2. 5.11.8.2.1.4.1.2 CK and ADDR_CTRL Routing, Two DDR3 Devices
              2. 5.11.8.2.1.4.2 Using Four 8-Bit DDR3 Devices
                1. 5.11.8.2.1.4.2.1 CK and ADDR_CTRL Topologies, Four DDR3 Devices
                2. 5.11.8.2.1.4.2.2 CK and ADDR_CTRL Routing, Four DDR3 Devices
              3. 5.11.8.2.1.4.3 One 16-Bit DDR3 Device
                1. 5.11.8.2.1.4.3.1 CK and ADDR_CTRL Topologies, One DDR3 Device
                2. 5.11.8.2.1.4.3.2 CK and ADDR_CTRL Routing, One DDR3 Device
            5. 5.11.8.2.1.5 Data Topologies and Routing Definition
              1. 5.11.8.2.1.5.1 DQS[x] and DQ[x] Topologies, Any Number of Allowed DDR3 Devices
              2. 5.11.8.2.1.5.2 DQS[x] and DQ[x] Routing, Any Number of Allowed DDR3 Devices
            6. 5.11.8.2.1.6 Routing Specification
              1. 5.11.8.2.1.6.1 CK and ADDR_CTRL Routing Specification
              2. 5.11.8.2.1.6.2 DQS[x] and DQ[x] Routing Specification
          2. 5.11.8.2.2 LPDDR2 Routing Guidelines
            1. 5.11.8.2.2.1 LPDDR2 Board Designs
            2. 5.11.8.2.2.2 LPDDR2 Device Configurations
            3. 5.11.8.2.2.3 LPDDR2 Interface
              1. 5.11.8.2.2.3.1 LPDDR2 Interface Schematic
              2. 5.11.8.2.2.3.2 Compatible JEDEC LPDDR2 Devices
              3. 5.11.8.2.2.3.3 LPDDR2 PCB Stackup
              4. 5.11.8.2.2.3.4 LPDDR2 Placement
              5. 5.11.8.2.2.3.5 LPDDR2 Keepout Region
              6. 5.11.8.2.2.3.6 LPDDR2 Net Classes
              7. 5.11.8.2.2.3.7 LPDDR2 Signal Termination
              8. 5.11.8.2.2.3.8 LPDDR2 DDR_VREF Routing
            4. 5.11.8.2.2.4 Routing Specification
              1. 5.11.8.2.2.4.1 DQS[x] and DQ[x] Routing Specification
              2. 5.11.8.2.2.4.2 CK and ADDR_CTRL Routing Specification
      9. 5.11.9  Display Subsystem (DSS)
      10. 5.11.10 Camera (VPFE)
      11. 5.11.11 Inter-Integrated Circuit (I2C)
        1. 5.11.11.1 I2C Electrical Data and Timing
          1. Table 5-69 I2C Timing Conditions - Slave Mode
          2. Table 5-70 Timing Requirements for I2C Input Timings
          3. Table 5-71 Switching Characteristics for I2C Output Timings
      12. 5.11.12 Multichannel Audio Serial Port (McASP)
        1. 5.11.12.1 McASP Device-Specific Information
        2. 5.11.12.2 McASP Electrical Data and Timing
          1. Table 5-72 McASP Timing Conditions
          2. Table 5-73 Timing Requirements for McASP
          3. Table 5-74 Switching Characteristics for McASP
      13. 5.11.13 Multichannel Serial Port Interface (McSPI)
        1. 5.11.13.1 McSPI Electrical Data and Timing
          1. 5.11.13.1.1 McSPI—Slave Mode
            1. Table 5-75 McSPI Timing Conditions—Slave Mode
            2. Table 5-76 Timing Requirements for McSPI Input Timings—Slave Mode
            3. Table 5-77 Switching Characteristics for McSPI Output Timings—Slave Mode
          2. 5.11.13.1.2 McSPI—Master Mode
            1. Table 5-78 McSPI Timing Conditions—Master Mode
            2. Table 5-79 Timing Requirements for McSPI Input Timings—Master Mode
            3. Table 5-80 Switching Characteristics for McSPI Output Timings—Master Mode
      14. 5.11.14 Quad Serial Port Interface (QSPI)
        1. Table 5-81 QSPI Switching Characteristics
      15. 5.11.15 HDQ/1-Wire Interface (HDQ/1-Wire)
        1. 5.11.15.1 HDQ Protocol
        2. 5.11.15.2 1-Wire Protocol
      16. 5.11.16 Programmable Real-Time Unit Subsystem and Industrial Communication Subsystem (PRU-ICSS)
        1. 5.11.16.1 Programmable Real-Time Unit (PRU-ICSS PRU)
          1. Table 5-86  PRU-ICSS PRU Timing Conditions
          2. 5.11.16.1.1 PRU-ICSS PRU Direct Input/Output Mode Electrical Data and Timing
            1. Table 5-87 PRU-ICSS PRU Timing Requirements - Direct Input Mode
            2. Table 5-88 PRU-ICSS PRU Switching Requirements - Direct Output Mode
          3. 5.11.16.1.2 PRU-ICSS PRU Parallel Capture Mode Electrical Data and Timing
            1. Table 5-89 PRU-ICSS PRU Timing Requirements - Parallel Capture Mode
          4. 5.11.16.1.3 PRU-ICSS PRU Shift Mode Electrical Data and Timing
            1. Table 5-90 PRU-ICSS PRU Timing Requirements - Shift In Mode
            2. Table 5-91 PRU-ICSS PRU Switching Requirements - Shift Out Mode
          5. 5.11.16.1.4 PRU-ICSS Sigma Delta Electrical Data and Timing
            1. Table 5-92 PRU-ICSS Timing Requirements - Sigma Delta Mode
          6. 5.11.16.1.5 PRU-ICSS ENDAT Electrical Data and Timing
            1. Table 5-93 PRU-ICSS Timing Requirements - ENDAT Mode
            2. Table 5-94 PRU-ICSS Switching Requirements - ENDAT Mode
        2. 5.11.16.2 PRU-ICSS EtherCAT (PRU-ICSS ECAT)
          1. Table 5-95  PRU-ICSS ECAT Timing Conditions
          2. 5.11.16.2.1 PRU-ICSS ECAT Electrical Data and Timing
            1. Table 5-96  PRU-ICSS ECAT Timing Requirements - Input Validated With LATCH_IN
            2. Table 5-97  PRU-ICSS ECAT Timing Requirements - Input Validated With SYNCx
            3. Table 5-98  PRU-ICSS ECAT Timing Requirements - Input Validated With Start of Frame (SOF)
            4. Table 5-99  PRU-ICSS ECAT Timing Requirements - LATCHx_IN
            5. Table 5-100 PRU-ICSS ECAT Switching Requirements - Digital IOs
        3. 5.11.16.3 PRU-ICSS MII_RT and Switch
          1. Table 5-101 PRU-ICSS MII_RT Switch Timing Conditions
          2. 5.11.16.3.1 PRU-ICSS MDIO Electrical Data and Timing
            1. Table 5-102 PRU-ICSS MDIO Timing Requirements - MDIO_DATA
            2. Table 5-103 PRU-ICSS MDIO Switching Characteristics - MDIO_CLK
            3. Table 5-104 PRU-ICSS MDIO Switching Characteristics - MDIO_DATA
          3. 5.11.16.3.2 PRU-ICSS MII_RT Electrical Data and Timing
            1. Table 5-105 PRU-ICSS MII_RT Timing Requirements - MII_RXCLK
            2. Table 5-106 PRU-ICSS MII_RT Timing Requirements - MII[x]_TXCLK
            3. Table 5-107 PRU-ICSS MII_RT Timing Requirements - MII_RXD[3:0], MII_RXDV, and MII_RXER
            4. Table 5-108 PRU-ICSS MII_RT Switching Characteristics - MII_TXD[3:0] and MII_TXEN
        4. 5.11.16.4 PRU-ICSS Universal Asynchronous Receiver Transmitter (PRU-ICSS UART)
          1. Table 5-109 Timing Requirements for PRU-ICSS UART Receive
          2. Table 5-110 Switching Characteristics Over Recommended Operating Conditions for PRU-ICSS UART Transmit
      17. 5.11.17 Multimedia Card (MMC) Interface
        1. 5.11.17.1 MMC Electrical Data and Timing
          1. Table 5-111 MMC Timing Conditions
          2. Table 5-112 Timing Requirements for MMC[0]_CMD and MMC[0]_DAT[7:0]
          3. Table 5-113 Timing Requirements for MMC[1/2]_CMD and MMC[1/2]_DAT[7:0]
          4. Table 5-114 Switching Characteristics for MMC[x]_CLK
          5. Table 5-115 Switching Characteristics for MMC[x]_CMD and MMC[x]_DAT[7:0]—HSPE=0
          6. Table 5-116 Switching Characteristics for MMC[x]_CMD and MMC[x]_DAT[7:0]—HSPE=1
      18. 5.11.18 Universal Asynchronous Receiver/Transmitter (UART)
        1. 5.11.18.1 UART Electrical Data and Timing
          1. Table 5-117 Timing Requirements for UARTx Receive
          2. Table 5-118 for UARTx Transmit
        2. 5.11.18.2 UART IrDA Interface
    12. 5.12 Emulation and Debug
      1. 5.12.1 IEEE 1149.1 JTAG
        1. 5.12.1.1 JTAG Electrical Data and Timing
          1. Table 5-121 Timing Requirements for JTAG
          2. Table 5-122 Switching Characteristics for JTAG
  6. 6Device and Documentation Support
    1. 6.1 Device Nomenclature
    2. 6.2 Tools and Software
    3. 6.3 Documentation Support
    4. 6.4 Community Resources
    5. 6.5 商标
    6. 6.6 静电放电警告
    7. 6.7 Glossary
  7. 7Mechanical, Packaging, and Orderable Information
    1. 7.1 Via Channel
    2. 7.2 Packaging Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • ZDN|491
散热焊盘机械数据 (封装 | 引脚)
订购信息

5.8 ADC0: Analog-to-Digital Subsystem Electrical Parameters

The analog-to-digital converter (ADC) subsystem (ADC0) contains a single-channel ADC connected to an 8:1 analog multiplexer which operates as a general-purpose ADC. The ADC0 subsystem can be configured for use in one of the following applications:

  • 8 general-purpose ADC channels

Table 5-5 summarizes the ADC0 subsystem electrical parameters.

Table 5-5 ADC0 Electrical Parameters

PARAMETER TEST CONDITIONS MIN NOM MAX UNIT
ANALOG INPUT
ADC0_VREFP(1) (0.5 × VDDA_ADC0) + 0.25 VDDA_ADC0 V
ADC0_VREFN(1) 0 (0.5 × VDDA_ADC0) – 0.25 V
ADC0_VREFP  + ADC0_VREFN VDDA_ADC0 V
Full-scale Input Range Internal Voltage Reference 0 VDDA_ADC0 V
External Voltage Reference ADC0_VREFN ADC0_VREFP
Differential Nonlinearity (DNL) Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V		 –1 0.5 1 LSB
Integral Nonlinearity (INL) Source impedance = 50 Ω
Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V		 –2 ±1 2 LSB
Source Impedance = 1 kΩ
Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V		 ±1
Gain Error Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V		 ±2 LSB
Offset Error Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V		 ±2 LSB
Input Sampling Capacitance 5.5 pF
Signal-to-Noise Ratio (SNR) Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V
Input Signal: 30 kHz sine wave at –0.5 dB Full Scale		 70 dB
Total Harmonic Distortion (THD) Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V
Input Signal: 30 kHz sine wave at –0.5 dB Full Scale		 75 dB
Spurious Free Dynamic Range Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V
Input Signal: 30 kHz sine wave at –0.5 dB Full Scale		 80 dB
Signal-to-Noise Plus Distortion Internal Voltage Reference:
VDDA_ADC0 = 1.8 V
External Voltage Reference:
VREFP – VREFN = 1.8 V
Input Signal: 30 kHz sine wave at –0.5 dB Full Scale		 69 dB
VREFP and VREFN Input Impedance 20 kΩ
Input Impedance of AIN[7:0](2) f = input frequency [1/((65.97 × 10–12) × f)] Ω
SAMPLING DYNAMICS
ADC Clock Frequency 13 MHz
Conversion Time 13 ADC0 clock cycles
Acquisition Time 2 257 ADC0 clock cycles
Sampling Rate(3) ADC0 Clock = 13 MHz 867 kSPS
Channel-to-Channel Isolation 100 dB
  1. The ADC0_VREFP and ADC0_VREFN terminals should not be allowed to float to prevent noise from coupling into the ADC. If ADC0_VREFN is not used to connect an external negative voltage reference to the ADC, connect it to VSSA_ADC. If ADC0_VREFP is not used to connect an external positive voltage reference to the ADC, connect it to VSSA_ADC or VDDA_ADC0. Connecting ADC0_VREFP to VSSA_ADC in this use case is the preferred option because VDDA_ADC0 may couple more noise into the ADC than VSSA_ADC.
  2. This parameter is valid when the respective AIN terminal is configured to operate as a general-purpose ADC input.
  3. The maximum sample rate assumes a conversion time of 13 ADC clock cycles with the acquisition time configured for the minimum of 2 ADC clock cycles, where it takes a total of 15 ADC clock cycles to sample the analog input and convert it to a positive binary weighted digital value.