ZHCSQT2 March   2024 ADS127L18

ADVANCE INFORMATION  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Timing Diagrams
  7. 6 Parameter Measurement Information
    1. 6.1  Offset Error Measurement
    2. 6.2  Offset Drift Measurement
    3. 6.3  Gain Error Measurement
    4. 6.4  Gain Drift Measurement
    5. 6.5  NMRR Measurement
    6. 6.6  CMRR Measurement
    7. 6.7  PSRR Measurement
    8. 6.8  SNR Measurement
    9. 6.9  INL Error Measurement
    10. 6.10 THD Measurement
    11. 6.11 IMD Measurement
    12. 6.12 SFDR Measurement
    13. 6.13 Noise Performance
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Inputs (AINP, AINN)
        1. 7.3.1.1 Input Range
      2. 7.3.2 Reference Voltage (REFP, REFN)
        1. 7.3.2.1 Reference Voltage Range
      3. 7.3.3 Clock Operation
        1. 7.3.3.1 Internal Oscillator
        2. 7.3.3.2 External Clock
      4. 7.3.4 Power Supplies
        1. 7.3.4.1 AVDD1 and AVSS
        2. 7.3.4.2 AVDD2
        3. 7.3.4.3 IOVDD
        4. 7.3.4.4 Power-On Reset (POR)
        5. 7.3.4.5 CAPA and CAPD
      5. 7.3.5 VCM Output Voltage
      6. 7.3.6 GPIO
      7. 7.3.7 Modulator
      8. 7.3.8 Digital Filter
        1. 7.3.8.1 Wideband Filter
      9. 7.3.9 Low-Latency Filter (Sinc)
        1. 7.3.9.1 Sinc4 Filter
        2. 7.3.9.2 Sinc4 + Sinc1 Cascade Filter
        3. 7.3.9.3 Sinc3 Filter
        4. 7.3.9.4 Sinc3 + Sinc1 Filter
    4. 7.4 Device Functional Modes
      1. 7.4.1  Speed Modes
      2. 7.4.2  Synchronization
        1. 7.4.2.1 Synchronized Control Mode
        2. 7.4.2.2 Start/Stop Control Mode
      3. 7.4.3  Digital Filter Settling
      4. 7.4.4  Conversion-Start Delay Time
      5. 7.4.5  Data Averaging
      6. 7.4.6  Calibration
        1. 7.4.6.1 Offset Calibration Registers
        2. 7.4.6.2 Gain Calibration Registers
        3. 7.4.6.3 Calibration Procedure
      7. 7.4.7  Reset
        1. 7.4.7.1 RESET Pin
        2. 7.4.7.2 Reset by SPI Register
        3. 7.4.7.3 Reset by SPI Input Pattern
      8. 7.4.8  Power-Down
      9. 7.4.9  Idle and Standby Modes
      10. 7.4.10 Diagnostics
        1. 7.4.10.1 ERROR Pin and ERR_FLAG Bit
        2. 7.4.10.2 Clock Counter
        3. 7.4.10.3 SCLK Counter
        4. 7.4.10.4 Frame-Sync CRC
        5. 7.4.10.5 SPI CRC
        6. 7.4.10.6 Register Map CRC
        7. 7.4.10.7 Self Test
      11. 7.4.11 Frame-Sync Data Port
        1. 7.4.11.1 FSYNC Pin
        2. 7.4.11.2 DCLK Pin
        3. 7.4.11.3 DOUTn Pins
        4. 7.4.11.4 DINn Pins
        5. 7.4.11.5 Time Division Multiplexing (TDM)
        6. 7.4.11.6 Data Size
        7. 7.4.11.7 STATUS_DP Header
        8. 7.4.11.8 Daisy Chain
        9. 7.4.11.9 Data Port Offset Timing
    5. 7.5 Programming
      1. 7.5.1 Hardware Programming
      2. 7.5.2 SPI Programming
        1. 7.5.2.1 Chip Select (CS)
        2. 7.5.2.2 Serial Clock (SCLK)
        3. 7.5.2.3 Serial Data Input (SDI)
        4. 7.5.2.4 Serial Data Output (SDO)
      3. 7.5.3 SPI Frame
      4. 7.5.4 SPI Commands
        1. 7.5.4.1 Read Register Command
        2. 7.5.4.2 Write Register Command
      5. 7.5.5 SPI Daisy-Chain
  9. 8 Register Map
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Input Driver
      2. 9.1.2 Antialias Filter
      3. 9.1.3 Reference Voltage
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 接收文档更新通知
    3. 10.3 支持资源
    4. 10.4 Trademarks
    5. 10.5 静电放电警告
    6. 10.6 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Mechanical Data

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.5.4.2 Write Register Command

The write register command writes register data. The write register operation is performed in a single frame. The first byte of the command is the base value (80h) added to the 7-bit register address. The second byte of the command is the register data. When the SPI out-of-range address feature is enabled, the write operation is rejected and the ADDR_ERR flag is set in the STATUS byte. The register data format is most-significant-bit first.

Figure 7-45 shows an example of writing register data with the SPI STATUS and CRC bytes disabled, resulting in a two-byte command operation. If the previous operation was a write register command, the first output byte is the echo of the previously written register data. Otherwise, the first output byte is the register data from the register read operation.

GUID-20230208-SS0I-K0GS-JBTJ-S3W9NWJPLPJK-low.svg Figure 7-45 Write Register Data (STATUS and CRC Disabled)

Figure 7-46 shows an example of a write register operation with the SPI STATUS and CRC bytes enabled. In this example, the frame is three bytes long because the STATUS and CRC bytes are enabled. If the previous operation was a write register command, the first output byte is the echo of the previously received register data. If a CRC error occurred in the previous frame, the previous write operation is rejected. The echo byte is then inverted, and the SPI_FLAG bit is set in the STATUS byte. Further register write operations are blocked until the CRC_FLAG in the STATUS register is reset. If the previous operation is a register read, the first output byte is register data.

GUID-20230208-SS0I-LKHZ-9MB9-BDSFJDBPXJPQ-low.svg Figure 7-46 Write Register Data (STATUS and CRC Enabled)