SLVSHZ5 November   2026 TPS544628

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  D-CAP4 Control
      2. 6.3.2  Internal VCC LDO and Using External Bias On the VCC Pin
        1. 6.3.2.1 Powering the Device From a Single Bus
        2. 6.3.2.2 Powering the Device From a Split-Rail Configuration
      3. 6.3.3  Multifunction Select (MS1) Pin
      4. 6.3.4  Multifunction Select (MS2) Pin
      5. 6.3.5  PMBus® Address (ADR) Pin
      6. 6.3.6  Output Voltage Setting
        1. 6.3.6.1 Setting VBOOT and VOUT_SCALE_LOOP
        2. 6.3.6.2 Setting Output Voltage (Internal Feedback)
        3. 6.3.6.3 Setting Output Voltage (External Feedback)
      7. 6.3.7  Switching Frequency
      8. 6.3.8  Dynamic Voltage Slew Rate
      9. 6.3.9  Enable
      10. 6.3.10 Soft Start and Soft Stop
      11. 6.3.11 Power Good
      12. 6.3.12 Overvoltage and Undervoltage Protection
      13. 6.3.13 Remote Sense
      14. 6.3.14 Low-side MOSFET Zero-Crossing
      15. 6.3.15 Current Sense and Positive Overcurrent Protection
      16. 6.3.16 Low-side MOSFET Negative Current Limit
      17. 6.3.17 Output Voltage Discharge
      18. 6.3.18 UVLO Protection
      19. 6.3.19 Telemetry
      20. 6.3.20 Thermal Shutdown
    4. 6.4 Device Functional Modes
      1. 6.4.1 Auto-Skip (PFM) Eco-mode Light Load Operation
      2. 6.4.2 Forced Continuous-Conduction Mode
  8. 7 Programming Registers
    1. 7.1 Register Map
      1. 7.1.1  OPERATION (Address = 01h)
      2. 7.1.2  ON_OFF_CONFIG (Address = 02h)
      3. 7.1.3  CLEAR_FAULTS (Address = 03h)
      4. 7.1.4  WRITE_PROTECT (Address = 10h)
      5. 7.1.5  STORE_USER_ALL (Address = 15h)
      6. 7.1.6  RESTORE_USER_ALL (Address = 16h)
      7. 7.1.7  CAPABILITY (Address = 19h)
      8. 7.1.8  VOUT_MODE (Address = 20h)
      9. 7.1.9  VOUT_COMMAND (Address = 21h)
      10.      55
      11. 7.1.10 VOUT_MARGIN_HIGH (Address = 25h)
      12. 7.1.11 VOUT_MARGIN_LOW (Address = 26h)
      13. 7.1.12 VOUT_TRANSITION_RATE (Address = 27h)
      14. 7.1.13 59
      15. 7.1.14 VOUT_SCALE_LOOP (Address = 29h)
      16. 7.1.15 FREQUENCY_SWITCH (Address = 33h)
      17. 7.1.16 62
      18. 7.1.17 VOUT_OV_FAULT_RESPONSE (Address = 41h)
      19. 7.1.18 VOUT_UV_FAULT_RESPONSE (Address = 45h)
      20.      65
      21. 7.1.19 IOUT_OC_FAULT_LIMIT (Address = 46h)
      22.      67
      23. 7.1.20 TON_DELAY (Address = 60h)
      24. 7.1.21 TON_RISE (Address = 61h)
      25.      70
      26. 7.1.22 TOFF_DELAY (Address = 64h)
      27. 7.1.23 TOFF_FALL (Address = 65h)
      28. 7.1.24 STATUS_BYTE (Address = 78h)
      29. 7.1.25 STATUS_WORD (Address = 79h)
      30. 7.1.26 STATUS_CML (Address = 7Eh)
      31. 7.1.27 STATUS_MFR_SPECIFIC (Address = 80h)
      32. 7.1.28 READ_VOUT (Address = 8Bh)
      33. 7.1.29 READ_IOUT (Address = 8Ch)
      34. 7.1.30 READ_TEMP1 (Address = 8Dh)
      35. 7.1.31 PMBUS_REVISION (Address = 98h)
      36. 7.1.32 MFR_ID (Address = 99h)
      37. 7.1.33 MFR_MODEL (Address = 9Ah)
      38. 7.1.34 MFR_REVISION (Address = 9Bh)
      39. 7.1.35 IC_DEVICE_ID (Address = ADh)
      40. 7.1.36 IC_DEVICE_REV (Address = AEh)
      41. 7.1.37 SYS_CFG_USER1 (Address = D1h)
      42. 7.1.38 PASSKEY (Address = D2h)
      43. 7.1.39 COMP (Address = D4h)
      44.      89
      45. 7.1.40 VBOOT (Address = D5h)
      46.      91
      47. 7.1.41 NVM_CHECKSUM (Address = D9h)
      48. 7.1.42 FUSION_ID0 (Address = FCh)
      49. 7.1.43 FUSION_ID1 (Address = FDh)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Output Voltage Setting Point
        2. 8.2.2.2 Choose the Switching Frequency
        3. 8.2.2.3 Choose the Inductor
        4. 8.2.2.4 Choose the Output Capacitor
        5. 8.2.2.5 Choose the Input Capacitors (CIN)
        6. 8.2.2.6 VCC Bypass Capacitor
        7. 8.2.2.7 BOOT Capacitor
        8. 8.2.2.8 PG Pullup Resistor
        9. 8.2.2.9 Choose the PMBus® Address and Fault Recovery Mode
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
      3. 8.4.3 Thermal Performance On TI EVM
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Tape and Reel Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)

Features

  • 4V to 16V input voltage range without external bias
  • 2.7V to 16V input voltage range with external bias
  • 3.1V to 4.5V external VCC bias support
  • 18mΩ and 7.5mΩ MOSFETs (VVCC = 3.3V)
  • 6A continuous output current
  • PMBus® 1.4 compliant
  • Optimized 19-pin WQFN-HR package for efficiency and thermal performance
  • 1% output voltage accuracy with internal feedback, TJ = –40°C to +150°C
  • 0.4V to 5.5V output voltage range
  • Differential remote sense
  • D-CAP4 with ultra-fast load-step response supports all ceramic output capacitors
  • User programmable NVM
  • Selectable auto-skip Eco-mode for high light-load efficiency
  • Programmable valley current limit
  • 500kHz, 600kHz, 800kHz, 1.0MHz, 1.2MHz, 1.4MHz selectable switching frequency
  • Programmable soft-start time
  • Prebiased start-up capability
  • Open-drain power-good output
  • Overvoltage and undervoltage fault protection
  • 3mm × 3mm (0.4mm pin pitch) and 3mm × 3.5mm (0.5 pin pitch) 19-pin QFN packages
  • Pin-to-pin compatible with 20A TPS544B28 and 12A TPS544A28