ZHCSUI2E May   2006  – January 2024 TPS28225

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Undervoltage Lockout (UVLO)
      2. 6.3.2 Output Active Low
      3. 6.3.3 Enable/Power Good
      4. 6.3.4 3-State Input
        1. 6.3.4.1 TPS28225 3-State Exit Mode
        2. 6.3.4.2 External Resistor Interference
      5. 6.3.5 Bootstrap Diode
      6. 6.3.6 Upper and Lower Gate Drivers
      7. 6.3.7 Dead-Time Control
      8. 6.3.8 Thermal Shutdown
    4. 6.4 Device Functional Modes
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Four Phases Driven by TPS28225 Driver
        2. 7.2.2.2 Switching The MOSFETs
        3. 7.2.2.3 List of Materials
      3. 7.2.3 Application Curves
    3. 7.3 System Examples
  9. 8 Power Supply Recommendations
  10. 9 Layout
    1. 9.1 Layout Guidelines
    2. 9.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 第三方产品免责声明
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 接收文档更新通知
    4. 10.4 支持资源
    5. 10.5 Trademarks
    6. 10.6 静电放电警告
    7. 10.7 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.2.1 Design Requirements

The VRM Reference Design is capable of driving 35 A per phase. In this example it has a nominal input voltage of 12 V within a tolerance range of ±5%. The switching frequency is 500 kHz. The nominal duty cycle is 10%, therefore the low-side MOSFETs are conducting 90% of the time. By choosing lower RDS(on) the conduction losses of the switching elements are minimized.

Table 7-1 VRM Reference Design Requirements
DESIGN PARAMETERVALUE
Supply voltage12 V ±5%
Output voltage0.83 V to 1.6 V
Frequency500 kHz
Peak-to-peak output voltage variation on load current transient (0 A to 100 A ) within 1 µs<160 mV
Dynamic output voltage change slew rate12.25 mV per 5 µs