ZHCSCK8G May   2014  – October 2017 LP8860-Q1

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     系统效率
  4. 4 修订历史记录
  5. 5 器件比较表
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics
    6. 7.6  Current Sinks Electrical Characteristics
    7. 7.7  Boost Converter Characteristics
    8. 7.8  Logic Interface Characteristics
    9. 7.9  VIN Undervoltage Protection (VIN_UVLO)
    10. 7.10 VDD Undervoltage Protection (VDD_UVLO)
    11. 7.11 VIN Overvoltage Protection (VIN_OVP)
    12. 7.12 VIN Overcurrent Protection (VIN_OCP)
    13. 7.13 Power-Line FET Control Electrical Characteristics
    14. 7.14 External Temp Sensor Control Electrical Characteristics
    15. 7.15 I2C Serial Bus Timing Parameters (SDA, SCLK)
    16. 7.16 SPI Timing Requirements
    17. 7.17 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
      1. 8.1.1 Boost Controller
      2. 8.1.2 LED Output Configurations
      3. 8.1.3 Display Mode
      4. 8.1.4 Cluster Mode
      5. 8.1.5 Hybrid Dimming
      6. 8.1.6 Charge Pump and Square Waveform (SQW) Output
      7. 8.1.7 Power-Line FET
      8. 8.1.8 Protection Features
      9. 8.1.9 Advanced Thermal Protection Features
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Clock Generation
        1. 8.3.1.1 LED PWM Clock Generation With VSYNC
        2. 8.3.1.2 LED PWM Frequency and Resolution
      2. 8.3.2 Brightness Control (Display Mode)
        1. 8.3.2.1 PWM Input Duty Cycle Based Control
        2. 8.3.2.2 Brightness Register Control
        3. 8.3.2.3 PWM Input Duty × Brightness Register
        4. 8.3.2.4 PWM-Input Direct Control
        5. 8.3.2.5 Brightness Slope
        6. 8.3.2.6 LED Dimming Methods
        7. 8.3.2.7 PWM Calculation Data Flow for Display Mode
      3. 8.3.3 LED Output Modes and Phase Shift PWM (PSPWM) Scheme
      4. 8.3.4 LED Current Setting
      5. 8.3.5 Cluster Mode
      6. 8.3.6 Boost Controller
      7. 8.3.7 Charge Pump
      8. 8.3.8 Powerline Control FET
      9. 8.3.9 Protection and Fault Detection Modes
        1. 8.3.9.1 LED Fault Comparators and Adaptive Boost Control
        2. 8.3.9.2 LED Current Dimming With Internal Temperature Sensor
        3. 8.3.9.3 LED Current Limitation With External NTC Sensor
        4. 8.3.9.4 LED Current Dimming With External NTC Sensor
        5. 8.3.9.5 Protection Feature and Fault Summary
    4. 8.4 Device Functional Modes
      1. 8.4.1 Standby Mode
      2. 8.4.2 Active Mode
      3. 8.4.3 Fault Recovery State
      4. 8.4.4 Start-Up and Shutdown Sequences
    5. 8.5 Programming
      1. 8.5.1 EEPROM
      2. 8.5.2 Serial Interface
        1. 8.5.2.1 SPI Interface
        2. 8.5.2.2 I2C Serial Bus Interface
          1. 8.5.2.2.1 Interface Bus Overview
          2. 8.5.2.2.2 Data Transactions
          3. 8.5.2.2.3 Acknowledge Cycle
          4. 8.5.2.2.4 Acknowledge After Every Byte Rule
          5. 8.5.2.2.5 Addressing Transfer Formats
          6. 8.5.2.2.6 Control Register Write Cycle
          7. 8.5.2.2.7 Control Register Read Cycle
    6. 8.6 Register Maps
      1. 8.6.1 Register Bit Explanations
        1. 8.6.1.1  Display/Cluster1 Brightness Control MSB
        2. 8.6.1.2  Display/Cluster1 Brightness Control LSB
        3. 8.6.1.3  Display/Cluster1 Output Current MSB
        4. 8.6.1.4  Display/Cluster1 Output Current LSB
        5. 8.6.1.5  Cluster2 Brightness Control MSB
        6. 8.6.1.6  Cluster2 Brightness Control LSB
        7. 8.6.1.7  Cluster2 Output Current
        8. 8.6.1.8  Cluster3 Brightness Control MSB
        9. 8.6.1.9  Cluster3 Brightness Control LSB
        10. 8.6.1.10 Cluster3 Output Current
        11. 8.6.1.11 Cluster4 Brightness Control MSB
        12. 8.6.1.12 Cluster4 Brightness Control LSB
        13. 8.6.1.13 Cluster4 Output Current
        14. 8.6.1.14 Configuration
        15. 8.6.1.15 Status
        16. 8.6.1.16 Fault
        17. 8.6.1.17 LED Fault
        18. 8.6.1.18 Fault Clear
        19. 8.6.1.19 Identification
        20. 8.6.1.20 Temp MSB
        21. 8.6.1.21 Temp LSB
        22. 8.6.1.22 Display LED Current MSB
        23. 8.6.1.23 Display LED Current LSB
        24. 8.6.1.24 Display LED PWM MSB
        25. 8.6.1.25 Display LED PWM LSB
        26. 8.6.1.26 EEPROM Control
        27. 8.6.1.27 EEPROM Unlock Code
      2. 8.6.2 EEPROM Bit Explanations
        1. 8.6.2.1  EEPROM Register 0
        2. 8.6.2.2  EEPROM Register 1
        3. 8.6.2.3  EEPROM Register 2
        4. 8.6.2.4  EEPROM Register 3
        5. 8.6.2.5  EEPROM Register 4
        6. 8.6.2.6  EEPROM Register 5
        7. 8.6.2.7  EEPROM Register 6
        8. 8.6.2.8  EEPROM Register 7
        9. 8.6.2.9  EEPROM Register 8
        10. 8.6.2.10 EEPROM Register 9
        11. 8.6.2.11 EEPROM Register 10
        12. 8.6.2.12 EEPROM Register 11
        13. 8.6.2.13 EEPROM Register 12
        14. 8.6.2.14 EEPROM Register 13
        15. 8.6.2.15 EEPROM Register 14
        16. 8.6.2.16 EEPROM Register 15
        17. 8.6.2.17 EEPROM Register 16
        18. 8.6.2.18 EEPROM Register 17
        19. 8.6.2.19 EEPROM Register 18
        20. 8.6.2.20 EEPROM Register 19
        21. 8.6.2.21 EEPROM Register 20
        22. 8.6.2.22 EEPROM Register 21
        23. 8.6.2.23 EEPROM Register 22
        24. 8.6.2.24 EEPROM Register 23
        25. 8.6.2.25 EEPROM Register 24
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Typical Application for Display Backlight
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1  Inductor Selection
          2. 9.2.1.2.2  Output Capacitor Selection
          3. 9.2.1.2.3  Input Capacitor Selection
          4. 9.2.1.2.4  Charge Pump Output Capacitor
          5. 9.2.1.2.5  Charge Pump Flying Capacitor
          6. 9.2.1.2.6  Diode
          7. 9.2.1.2.7  Boost Converter Transistor
          8. 9.2.1.2.8  Boost Sense Resistor
          9. 9.2.1.2.9  Power Line Transistor
          10. 9.2.1.2.10 Input Current Sense Resistor
          11. 9.2.1.2.11 Filter Component Values
            1. 9.2.1.2.11.1 Critical Components for Design
        3. 9.2.1.3 Application Performance Plots
      2. 9.2.2 Low VDD Voltage and Combined Output Mode Application
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
        3. 9.2.2.3 Application Performance Plots
      3. 9.2.3 High Output Voltage Application
        1. 9.2.3.1 Design Requirements
        2. 9.2.3.2 Detailed Design Procedure
        3. 9.2.3.3 Application Performance Plots
      4. 9.2.4 High Output Current Application
        1. 9.2.4.1 Design Requirements
        2. 9.2.4.2 Detailed Design Procedure
        3. 9.2.4.3 Application Performance Plots
      5. 9.2.5 Three-Channel Configuration Without Serial Interface
        1. 9.2.5.1 Design Requirements
        2. 9.2.5.2 Detailed Design Procedure
        3. 9.2.5.3 Application Performance Plots
      6. 9.2.6 Solution With Minimum External Components
        1. 9.2.6.1 Design Requirements
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 器件支持
      1. 12.1.1 第三方产品免责声明
    2. 12.2 文档支持
      1. 12.2.1 相关文档
    3. 12.3 接收文档更新通知
    4. 12.4 社区资源
    5. 12.5 商标
    6. 12.6 静电放电警告
    7. 12.7 Glossary
  13. 13机械、封装和可订购信息

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • VFP|32
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.3.5 Cluster Mode

Cluster is a simplified mode which allows independent current and PWM control for every string in cluster mode. In this mode brightness control is limited to conventional PWM through the SPI/I2C brightness registers. The PWM input pin, Hybrid PWM and Current dimming mode, slope control, or dither are not available. Brightness for different LED strings depends on <DISP_CL1_BRT[15:0]>, <CL2_BRT[12:0]>, <CL3_BRT[12:0]> and <CL4_BRT[12:0]> registers. If OUT1 is in cluster mode, only 13 MSB are used. If all LED outputs are in the cluster mode, LED output PWM resolution is always 13 bits, and frequency depends on <PWM_RESOLUTION[1:0]> bits (see Table 13). If one or more of the LED outputs is in display mode, frequency, and resolution for strings in the cluster mode is the same as for strings in the display mode (see Table 1).

LP8860-Q1 cluster_mode_circ_snvsa21.gifFigure 20. Cluster Mode Block Diagram

Table 13. Output PWM Frequency for Mode 7 (All Strings in Cluster Mode)

PWM_RESOLUTION[1:0] 00 01 10 11
OSC frequency (MHz) 5 10 20 40
ƒLED PWM (Hz) 610 1221 2442 4883

When the LP8860-Q1 is set in cluster mode, fault protection functionality is limited. Headroom for LED strings must be between the high-voltage comparator level <DRV_LED_FAULT_THR[1:0]> and low-voltage comparator level <DRV_HEADR[2:0]> (which depend upon saturation voltage); otherwise a fault is generated.

Adaptive boost control does not follow strings in cluster mode. Display mode strings and cluster mode strings must not be connected to the same boost. When LED strings in display and cluster modes are connected to the same boost, LED open or short faults may be generated if the LED forward-voltage mismatch is too high.

If all LED outputs are in cluster mode, boost output voltage is fixed and must be set by EEPROM <BOOST_INITIAL_VOLTAGE[5:0]> bits to a value high enough to ensure correct LED string operation in all conditions.

<EN_CL_LED_FAULT>=0 disables cluster LED fault detection, even if all LED strings are in the cluster mode. The current de-rating (based on the internal temperature sensor) and LED current limitation (based on external temperature sensor) are not functional in this mode, and analog current dimming based on the external sensor functionality is limited (LED shutdown for high temperature is not operational).