ZHCSPA0 September   2023 LP5813

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
  9. 8 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Synchronous Boost Converter
        1. 9.3.1.1 Undervoltage Lockout
        2. 9.3.1.2 Enable and Soft Start
        3. 9.3.1.3 Switching Frequency
        4. 9.3.1.4 Current Limit Operation
        5. 9.3.1.5 Boost PWM Mode
        6. 9.3.1.6 Boost PFM Mode
        7. 9.3.1.7 Pass-Through Mode
      2. 9.3.2 Time-cross-multiplexing (TCM) scheme
        1. 9.3.2.1 Direct drive mode
        2. 9.3.2.2 TCM drive mode
        3. 9.3.2.3 Mix drive mode
        4. 9.3.2.4 Ghosting elimination
      3. 9.3.3 Analog Dimming
      4. 9.3.4 PWM Dimming
      5. 9.3.5 Autonomous Animation Engine Control
        1. 9.3.5.1 Animation Engine Pattern
        2. 9.3.5.2 Sloper
        3. 9.3.5.3 Animation Engine Unit (AEU)
        4. 9.3.5.4 Animation Pause Unit (APU)
      6. 9.3.6 Protections and Diagnostics
        1. 9.3.6.1 Overvoltage Protection
        2. 9.3.6.2 Output Short-to-Ground Protection
        3. 9.3.6.3 LED Open Detections
        4. 9.3.6.4 LED Short Detections
        5. 9.3.6.5 Thermal Shutdown
    4. 9.4 Device Functional Modes
    5. 9.5 Programming
    6. 9.6 Register Map Table
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Application
      2. 10.2.2 Design Parameters
      3. 10.2.3 Detailed Design Procedure
        1. 10.2.3.1 Inductor Selection
        2. 10.2.3.2 Output Capacitor Selection
        3. 10.2.3.3 Input Capacitor Selection
        4. 10.2.3.4 Program Procedure
        5. 10.2.3.5 Programming Example
      4. 10.2.4 Application Performance Plots
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
    2. 11.2 接收文档更新通知
    3. 11.3 支持资源
    4. 11.4 Trademarks
    5. 11.5 静电放电警告
    6. 11.6 术语表
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

9.3.6.4 LED Short Detections

The LP5813 integrates LED short detection (LSD) for the fault caused by any short LED. The threshold of LSD is able to configure from (0.35 × VOUT) V to (0.65 × VOUT) V by configuring lsd_threshold in Dev_config_12 register. To have enough detection time, LSD can only be performed when the PWM setting of this LED is above 25. If the voltage on the cathode of this LED is higher than the LSD threshold in continuously 3 cycles, LED short of this LED is reported to the corresponding LSD_status register.

The LSD flags can be cleared by writing 1h to lsd_clear in Fault_CLR register. If the LED short status is removed, the related lsd_status bit is set to 0 automatically.

The 'lsd_action' bit in Dev_config_12 register can determine the reaction once open fault is detected. When the 'lsd_action' bit is set to 1h, all LEDs are turned off which is called one fails all fail (OFAF) action, to prevent potential damage caused by the short issue. The device enters to STANDBY state after sending 'lsd_clear' command. When the 'lsd_action' bit is 0, no additional action is taken after LSD is detected. LSD detecion is only executed in NORMAL state.