ZHCSSI3 February   2024 ADS1288

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements: 1.65V ≤ IOVDD ≤ 1.95V and 2.7V ≤ IOVDD ≤ 3.6V
    7. 5.7 Switching Characteristics: 1.65V ≤ IOVDD ≤ 1.95V and 2.7V ≤ IOVDD ≤ 3.6V
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Noise Performance
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Input
      2. 7.3.2 PGA and Buffer
        1. 7.3.2.1 Programmable Gain Amplifier (PGA)
        2. 7.3.2.2 Buffer Operation (PGA Bypass)
      3. 7.3.3 Voltage Reference Input
      4. 7.3.4 IOVDD Power Supply
      5. 7.3.5 Modulator
        1. 7.3.5.1 Modulator Overdrive
      6. 7.3.6 Digital Filter
        1. 7.3.6.1 Sinc Filter Section
        2. 7.3.6.2 FIR Filter Section
        3. 7.3.6.3 Group Delay and Step Response
          1. 7.3.6.3.1 Linear Phase Response
          2. 7.3.6.3.2 Minimum Phase Response
        4. 7.3.6.4 HPF Stage
      7. 7.3.7 Clock Input
      8. 7.3.8 GPIO
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power-Down Mode
      2. 7.4.2 Reset
      3. 7.4.3 Synchronization
        1. 7.4.3.1 Pulse-Sync Mode
        2. 7.4.3.2 Continuous-Sync Mode
      4. 7.4.4 Sample Rate Converter
      5. 7.4.5 Offset and Gain Calibration
        1. 7.4.5.1 OFFSET Register
        2. 7.4.5.2 GAIN Register
        3. 7.4.5.3 Calibration Procedure
    5. 7.5 Programming
      1. 7.5.1 Serial Interface
        1. 7.5.1.1 Chip Select (CS)
        2. 7.5.1.2 Serial Clock (SCLK)
        3. 7.5.1.3 Data Input (DIN)
        4. 7.5.1.4 Data Output (DOUT)
        5. 7.5.1.5 Data Ready (DRDY)
      2. 7.5.2 Conversion Data Format
      3. 7.5.3 Commands
        1. 7.5.3.1  Single Byte Command
        2. 7.5.3.2  WAKEUP: Wake Command
        3. 7.5.3.3  STANDBY: Software Power-Down Command
        4. 7.5.3.4  SYNC: Synchronize Command
        5. 7.5.3.5  RESET: Reset Command
        6. 7.5.3.6  Read Data Direct
        7. 7.5.3.7  RDATA: Read Conversion Data Command
        8. 7.5.3.8  RREG: Read Register Command
        9. 7.5.3.9  WREG: Write Register Command
        10. 7.5.3.10 OFSCAL: Offset Calibration Command
        11. 7.5.3.11 GANCAL: Gain Calibration Command
  9. 8 Register Map
    1. 8.1 Register Descriptions
      1. 8.1.1 ID/SYNC: Device ID, SYNC Register (Address = 00h) [Reset = xxxx0010b]
      2. 8.1.2 CONFIG0: Configuration Register 0 (Address = 01h) [Reset = 92h]
      3. 8.1.3 CONFIG1: Configuration Register 1 (Address = 02h) [Reset = 10h]
      4. 8.1.4 HPF0, HPF1: High-Pass Filter Registers (Address = 03h, 04h) [Reset = 32h, 03h]
      5. 8.1.5 OFFSET0, OFFSET1, OFFSET2: Offset Calibration Registers (Address = 05h, 06h, 07h) [Reset = 00h, 00h, 00h]
      6. 8.1.6 GAIN0, GAIN1, GAIN2: Gain Calibration Registers (Address = 08h, 09h, 0Ah) [Reset = 00h, 00h, 40h]
      7. 8.1.7 GPIO: Digital Input/Output Register (Address = 0Bh) [Reset = 000xx000b]
      8. 8.1.8 SRC0, SRC1: Sample Rate Converter Registers (Address = 0Ch, 0Dh) [Reset = 00h, 80h]
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 Analog Power Supplies
      2. 9.3.2 Digital Power Supply
      3. 9.3.3 Grounds
      4. 9.3.4 Thermal Pad
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 接收文档更新通知
    2. 10.2 支持资源
    3. 10.3 Trademarks
    4. 10.4 静电放电警告
    5. 10.5 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

4 Pin Configuration and Functions

GUID-20200819-CA0I-RTTF-H42Q-Q7FCFXWMZV5M-low.svg Figure 4-1 RHB Package, 32-Pin, 5mm × 5mm VQFN (Top View)
Table 4-1 Pin Functions
PIN TYPE DESCRIPTION
NO. NAME
1 AIN1P Analog input Channel 1 positive input.
2 AIN1N Analog input Channel 1 negative input.
3 AIN2P Analog input Channel 2 positive input.
4 AIN2N Analog input Channel 2 negative input.
5 CAPP Analog internal PGA positive capacitor. Connect a 10nF C0G capacitor across CAPP and CAPN.
6 CAPN Analog internal PGA negative capacitor. Connect a 10nF C0G capacitor across CAPP and CAPN.
7 CAPBP Analog internal Buffer positive capacitor. Connect a 47nF C0G capacitor to AVSS.
8 CAPBN Analog internal Buffer negative capacitor. Connect a 47nF C0G capacitor to AVSS.
9 CAPC Analog internal Charge-pump capacitor. Connect a 4.7nF, minimum 10V rated capacitor to AGND.
10 AVSS Analog supply PGA negative analog supply. See the Analog Power Supplies section for details.
11 AVDD1 Analog supply PGA positive analog supply. See the Analog Power Supplies section for details.
12 AVDD2 Analog supply Modulator analog supply. See the Analog Power Supplies section for details.
13 AGND Analog ground Analog ground.
14 CAPI Analog internal Input bias capacitor. Connect a 100nF ceramic capacitor to AGND.
15 GPIO0 Digital I/O General-purpose I/O.
16 GPIO1 Digital I/O General-purpose I/O.
17 CAPD Analog output Digital low-dropout regulator (LDO) output. Connect a 220nF ceramic capacitor to DGND.
18 DGND Ground Digital ground.
19 IOVDD Digital supply Digital I/O power supply. See the IOVDD Power Supply section for details.
20 CLK Digital input ADC clock input.
21 CS Digital input Serial interface select, active low.
22 SCLK Digital input Serial interface clock.
23 DIN Digital input Serial interface data in.
24 DOUT Digital output Serial interface data out.
25 DRDY Digital output Data ready, active low.
26 SYNC Digital input ADC synchronization, active high.
27 RESET Digital input ADC reset, active low.
28 PWDN Digital input ADC power down, active low.
29 REFN Analog input Negative reference input. See the Voltage Reference Input section for details.
30 REFP Analog input Positive reference input. See the Voltage Reference Input section for details.
31 CAPR Analog internal Reference bias capacitor. Connect a 100nF ceramic capacitor to AVSS.
32 AVSS Analog supply PGA negative supply.
Thermal pad Connect the thermal pad to AVSS. Thermal vias placed in the printed circuit board (PCB) land are optional to allow placement of bottom side components.