首頁 電源管理 閘極驅動器 半橋式驅動器
首頁
電源管理
閘極驅動器
半橋式驅動器

UCC27284-Q1

現行

具有 5V UVLO 和啟用選項的車用 120V 3A 半橋閘極驅動器

立即訂購
產品規格表

現在提供此產品的更新版本

open-in-new 比較替代產品
針腳對針腳的功能與所比較的裝置相同。
UCC27212A-Q1 現行 具有 5V UVLO 的汽車、4A、120V 半橋閘極驅動器 Similar half-bridge driver with higher drive current and similar electrical characteristics

UCC27284-Q1

現行
產品規格表 立即訂購

產品詳細資料

Bootstrap supply voltage (max) (V) 120 Power switch MOSFET Input supply voltage (min) (V) 5.5 Input supply voltage (max) (V) 16 Peak output current (A) 3 Operating temperature range (°C) -40 to 125 Undervoltage lockout (typ) (V) 5 Rating Automotive Propagation delay time (µs) 0.016 Rise time (ns) 12 Fall time (ns) 10 Iq (mA) 0.002, 2000 Input threshold TTL Channel input logic TTL Switch node voltage (V) -14 Features Enable, Integrated bootstrap diode, Negative Voltage Handling on Input TI functional safety category Functional Safety-Capable Driver configuration Dual inputs
Bootstrap supply voltage (max) (V) 120 Power switch MOSFET Input supply voltage (min) (V) 5.5 Input supply voltage (max) (V) 16 Peak output current (A) 3 Operating temperature range (°C) -40 to 125 Undervoltage lockout (typ) (V) 5 Rating Automotive Propagation delay time (µs) 0.016 Rise time (ns) 12 Fall time (ns) 10 Iq (mA) 0.002, 2000 Input threshold TTL Channel input logic TTL Switch node voltage (V) -14 Features Enable, Integrated bootstrap diode, Negative Voltage Handling on Input TI functional safety category Functional Safety-Capable Driver configuration Dual inputs
SOIC (D) 8 29.4 mm² (4.9 mm × 6 mm)
  • AEC-Q100 qualified with following results
    • Temperature grade 1 (Tj = –40°C to 150°C)
    • Device HBM ESD classification level 1B
    • Device CDM ESD classification level C3
  • Drives two N-channel MOSFETs in high-side low-side configuration
  • 5-V typical undervoltage lockout
  • 16-ns typical propagation delay
  • 12-ns rise, 10-ns fall time with 1.8-nF load
  • 1-ns typical delay matching
  • 5-V negative voltage handling on inputs
  • 14-V negative voltage handling on HS
  • ±3-A peak output current
  • Absolute maximum boot voltage 120 V
  • Integrated bootstrap diode
  • AEC-Q100 qualified with following results
    • Temperature grade 1 (Tj = –40°C to 150°C)
    • Device HBM ESD classification level 1B
    • Device CDM ESD classification level C3
  • Drives two N-channel MOSFETs in high-side low-side configuration
  • 5-V typical undervoltage lockout
  • 16-ns typical propagation delay
  • 12-ns rise, 10-ns fall time with 1.8-nF load
  • 1-ns typical delay matching
  • 5-V negative voltage handling on inputs
  • 14-V negative voltage handling on HS
  • ±3-A peak output current
  • Absolute maximum boot voltage 120 V
  • Integrated bootstrap diode

The UCC27284 -Q1 is a robust N-channel MOSFET driver with a maximum switch node (HS) voltage rating of 100 V. It allows for two N-channel MOSFETs to be controlled in half-bridge or synchronous buck configuration-based topologies. Its 3-A peak source and sink current along with low pull-up and pull-down resistance allows the UCC27284 -Q1 to drive large power MOSFETs with minimum switching losses during the transition of the MOSFET Miller plateau. Since the inputs are independent of the supply voltage, UCC27284 -Q1 can be used in conjunction with both analog and digital controllers. Two inputs, and therefore outputs, can be overlapped, if needed, in applications such as secondary side full-bridge synchronous rectification.

The input pins as well as the HS pin are able to tolerate significant negative voltage, which improves system robustness. 5-V UVLO allows systems to operate at lower bias voltages, which is necessary in many high frequency applications and improves system efficiency in certain operating modes. Small propagation delay and delay matching specifications minimize the dead-time requirement which further improves efficiency.

Undervoltage lockout (UVLO) is provided for both the high-side and low-side driver stages forcing the outputs low if the VDD voltage is below the specified threshold. An integrated bootstrap diode eliminates the need for an external discrete diode in many applications, which saves board space and reduces system cost. UCC27284-Q1 is offered in SOIC package for harsh system environments.

The UCC27284 -Q1 is a robust N-channel MOSFET driver with a maximum switch node (HS) voltage rating of 100 V. It allows for two N-channel MOSFETs to be controlled in half-bridge or synchronous buck configuration-based topologies. Its 3-A peak source and sink current along with low pull-up and pull-down resistance allows the UCC27284 -Q1 to drive large power MOSFETs with minimum switching losses during the transition of the MOSFET Miller plateau. Since the inputs are independent of the supply voltage, UCC27284 -Q1 can be used in conjunction with both analog and digital controllers. Two inputs, and therefore outputs, can be overlapped, if needed, in applications such as secondary side full-bridge synchronous rectification.

The input pins as well as the HS pin are able to tolerate significant negative voltage, which improves system robustness. 5-V UVLO allows systems to operate at lower bias voltages, which is necessary in many high frequency applications and improves system efficiency in certain operating modes. Small propagation delay and delay matching specifications minimize the dead-time requirement which further improves efficiency.

Undervoltage lockout (UVLO) is provided for both the high-side and low-side driver stages forcing the outputs low if the VDD voltage is below the specified threshold. An integrated bootstrap diode eliminates the need for an external discrete diode in many applications, which saves board space and reduces system cost. UCC27284-Q1 is offered in SOIC package for harsh system environments.
filter 尋找其它 半橋式驅動器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
針腳對針腳的功能與所比較的裝置相同。
UCC27301A-Q1 現行 具有 8V UVLO、互鎖和啟用選項的車用 120V 4.5A 半橋式驅動器 More recent pin-to-pin driver with 8V UVLO, higher drive current, input interlock and similar electrical characteristics
UCC27282-Q1 現行 具有 5V UVLO、互鎖功能和啟用選項的車用 120V 3A 半橋閘極驅動器 Includes input interlock to prevent cross-conduction.

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 18
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 UCC27284-Q1Automotive 3-A 120-V Half-Bridge Driver with Negative Voltage Handling and Low Switching Losses datasheet (Rev. B) PDF | HTML 2022/5/27
應用說明 Mapping Application Requirements with the 120V Halfbridge Gate Driver (Rev. A) PDF | HTML 2026/2/27
應用說明 Using Half-Bridge Gate Driver to Achieve 100% Duty Cycle for High Side FET PDF | HTML 2024/3/25
應用說明 Challenges and Solutions for Half-Bridge Gate Drivers in Bidirectional DC-DC Converters PDF | HTML 2024/1/24
應用說明 Bootstrap Circuitry Selection for Half Bridge Configurations (Rev. A) PDF | HTML 2023/9/8
功能安全資訊 UCC27282-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA (Rev. B) PDF | HTML 2022/11/14
應用說明 Comparative Analysis of Two Different Methods for Gate-Drive Current Boosting (Rev. A) PDF | HTML 2022/2/17
應用說明 Voltage Fed Full Bridge DC-DC & DC-AC Converter High-Freq Inverter Using C2000 (Rev. D) 2021/4/7
應用說明 Understanding and comparing peak current capability of gate drivers PDF | HTML 2021/3/30
更多文件說明 Troubleshooting gate drive circuits in automotive and industrial applications 2021/3/23
應用說明 Implementing High-Side Switches Using Half-Bridge Gate Drivers for 48-V Battery. 2020/5/12
Application brief External Gate Resistor Selection Guide (Rev. A) 2020/2/28
Application brief Understanding Peak IOH and IOL Currents (Rev. A) 2020/2/28
Application brief Small Price Competitive 100-V Driver for 48-V BLDC Motor Drives 2019/10/22
應用說明 Maximizing DC/DC converter designs with UCC27282 2019/1/18
應用說明 UCC27282 Improving motor drive system robustness 2019/1/11
應用說明 PFC Design Choice for On Board Charger Designs 2018/5/24
Application brief Reducing Switching Losses in On-Board Chargers for Electric Vehicles 2018/3/27

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

UCC27282EVM-335 — UCC27282 120V、3A、5V UVLO 高壓側低壓側閘極驅動器評估模組

UCC27282EVM-335 專為評估 UCC27282DRC 而設計，這是一款具備高源極和汲極峰值電流能力的 120V 半橋閘極驅動器。此 EVM 的目標是依照產品規格表參數評估驅動器 IC。EVM 也可當成驅動器 IC 元件選擇指南使用。EVM 可用於判斷對閘極驅動器性能的 PCB 佈線圖影響。
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發板

UCC27288EVM — UCC27288 100-V、3-A、8-V UVLO 半橋閘極驅動器評估模組

UCC27288EVM 專為評估 UCC27288D 而設計，這是一款具備 2.5-A 峰值電流源和 3.5-A 峰值汲極電流能力的 100-V 半橋閘極驅動器。此 EVM 可做為驅動功率 MOSFET 的參考設計，驅動電壓高達 20-V。
使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
計算工具

SLURB12 — UCC272xx-UCC273xx Schematic Review Template

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
SOIC (D) 8 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片