ZHCSQS1B february   2022  – august 2023 CC2651R3SIPA

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 功能方框图
  6. 5 Revision History
  7. 6 Device Comparison
  8. 7 Terminal Configuration and Functions
    1. 7.1 Pin Diagram
    2. 7.2 Signal Descriptions – SIPA Package
    3. 7.3 Connections for Unused Pins and Modules
  9. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Power Supply and Modules
    5. 8.5  Power Consumption - Power Modes
    6. 8.6  Power Consumption - Radio Modes
    7. 8.7  Nonvolatile (Flash) Memory Characteristics
    8. 8.8  Thermal Resistance Characteristics
    9. 8.9  RF Frequency Bands
    10. 8.10 Antenna Characteristics
    11. 8.11 Bluetooth Low Energy - Receive (RX)
    12. 8.12 Bluetooth Low Energy - Transmit (TX)
    13. 8.13 Zigbee - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - RX
    14. 8.14 Zigbee - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - TX
    15. 8.15 Timing and Switching Characteristics
      1. 8.15.1 Reset Timing
      2. 8.15.2 Wakeup Timing
      3. 8.15.3 Clock Specifications
        1. 8.15.3.1 48 MHz Crystal Oscillator (XOSC_HF)
        2. 8.15.3.2 48 MHz RC Oscillator (RCOSC_HF)
        3. 8.15.3.3 32.768 kHz Crystal Oscillator (XOSC_LF)
        4. 8.15.3.4 32 kHz RC Oscillator (RCOSC_LF)
      4. 8.15.4 Synchronous Serial Interface (SSI) Characteristics
        1. 8.15.4.1 Synchronous Serial Interface (SSI) Characteristics
        2.       37
      5. 8.15.5 UART
        1. 8.15.5.1 UART Characteristics
    16. 8.16 Peripheral Characteristics
      1. 8.16.1 ADC
        1. 8.16.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 8.16.2 DAC
        1. 8.16.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 8.16.3 Temperature and Battery Monitor
        1. 8.16.3.1 Temperature Sensor
        2. 8.16.3.2 Battery Monitor
      4. 8.16.4 Comparators
        1. 8.16.4.1 Continuous Time Comparator
      5. 8.16.5 Current Source
        1. 8.16.5.1 Programmable Current Source
      6. 8.16.6 GPIO
        1. 8.16.6.1 GPIO DC Characteristics
    17. 8.17 Typical Characteristics
      1. 8.17.1 MCU Current
      2. 8.17.2 RX Current
      3. 8.17.3 TX Current
      4. 8.17.4 RX Performance
      5. 8.17.5 TX Performance
      6. 8.17.6 ADC Performance
  10. 9 Detailed Description
    1. 9.1  Overview
    2. 9.2  System CPU
    3. 9.3  Radio (RF Core)
      1. 9.3.1 Bluetooth 5.2 Low Energy
      2. 9.3.2 802.15.4 (Zigbee)
    4. 9.4  Memory
    5. 9.5  Cryptography
    6. 9.6  Timers
    7. 9.7  Serial Peripherals and I/O
    8. 9.8  Battery and Temperature Monitor
    9. 9.9  µDMA
    10. 9.10 Debug
    11. 9.11 Power Management
    12. 9.12 Clock Systems
    13. 9.13 Network Processor
    14. 9.14 Device Certification and Qualification
      1. 9.14.1 FCC Certification and Statement
      2. 9.14.2 IC/ISED Certification and Statement
      3. 9.14.3 ETSI/CE Certification
      4. 9.14.4 UK Certification
      5. 9.14.5 MIC Certification
      6. 9.14.6 Korea Certification
      7. 9.14.7 NCC Certification and Statement
    15. 9.15 Module Markings
    16. 9.16 End Product Labeling
    17. 9.17 Manual Information to the End User
  11. 10Application, Implementation, and Layout
    1. 10.1 Typical Application Circuit
    2. 10.2 Alternate Application Circuit
    3. 10.3 Device Connections
      1. 10.3.1 Reset
      2. 10.3.2 Unused Pins
    4. 10.4 PCB Layout Guidelines
      1. 10.4.1 General Layout Recommendations
      2. 10.4.2 Typical RF Layout Recommendations with Integrated Antenna
      3. 10.4.3 RF Layout Recommendations with External Antenna
        1. 10.4.3.1 External Antenna Placement and Routing
        2. 10.4.3.2 Transmission Line Considerations
      4. 10.4.4 Alternate PCB Layout Guidelines
    5. 10.5 Reference Designs
    6. 10.6 Junction Temperature Calculation
  12. 11Environmental Requirements and SMT Specifications
    1. 11.1 PCB Bending
    2. 11.2 Handling Environment
      1. 11.2.1 Terminals
      2. 11.2.2 Falling
    3. 11.3 Storage Condition
      1. 11.3.1 Moisture Barrier Bag Before Opened
      2. 11.3.2 Moisture Barrier Bag Open
    4. 11.4 PCB Assembly Guide
      1. 11.4.1 PCB Land Pattern & Thermal Vias
      2. 11.4.2 SMT Assembly Recommendations
      3. 11.4.3 PCB Surface Finish Requirements
      4. 11.4.4 Solder Stencil
      5. 11.4.5 Package Placement
      6. 11.4.6 Solder Joint Inspection
      7. 11.4.7 Rework and Replacement
      8. 11.4.8 Solder Joint Voiding
    5. 11.5 Baking Conditions
    6. 11.6 Soldering and Reflow Condition
  13. 12Device and Documentation Support
    1. 12.1 Device Nomenclature
    2. 12.2 Tools and Software
      1. 12.2.1 SimpleLink™ Microcontroller Platform
    3. 12.3 Documentation Support
    4. 12.4 支持资源
    5. 12.5 Trademarks
    6. 12.6 静电放电警告
    7. 12.7 术语表
  14. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

10.4.3.1 External Antenna Placement and Routing

The antenna is the element used to convert the guided waves on the PCB traces to the free space electromagnetic radiation. The placement and layout of the antenna are the keys to increased range and data rates. Table 10-4 provides a summary of the antenna guidelines to follow with the CC2651R3SIPA module when using the module with an external antenna.

Table 10-4 External Antenna Guidelines
SR NO. GUIDELINES
1 Place the antenna on an edge of the PCB.
2 Ensure that no signals are routed across the antenna elements on any PCB layer.
3 Most antennas, including the PCB antenna used on the LaunchPad™, require ground clearance on all the layers of the PCB. Ensure that the ground is cleared on inner layers as well.
4 Ensure that there is provision to place matching components for the antenna. These must be tuned for best return loss when the complete board is assembled. Any plastics or casing must also be mounted while tuning the antenna because this can impact the impedance.
5 Ensure that the antenna impedance is 50 Ω because the module is rated to work only with a 50-Ω system.
6 In case of printed antenna, ensure that the simulation is performed with the solder mask in consideration.
7 Ensure that the antenna has a near omnidirectional pattern.

Table 10-5 lists the recommended external antennas to use with the CC2651R3SIPA module. Other external antennas may be available for use with the CC2651R3SIPA module.

Table 10-5 Recommended Components
CHOICE ANTENNA MANUFACTURER NOTES
1 2.4-GHz Inverted F Antenna Texas Instruments Refer to 2.4-GHz Inverted F Antenna for details of the antenna implementation and PCB requirements.