ZHCSVF5E July   1985  – March 2024 SN75ALS192

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 Dissipation Rating Table
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
    7. 5.7 Typical Characteristics Operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied.
  7. 6 Parameter Measurement Information
  8. 7 Device Functional Modes
  9. 8 Device and Documentation Support
    1. 8.1 接收文档更新通知
    2. 8.2 支持资源
    3. 8.3 商标
    4. 8.4 静电放电警告
    5. 8.5 术语表
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • NS|16
  • N|16
  • D|16
散热焊盘机械数据 (封装 | 引脚)
订购信息

5.5 Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS(1) MIN TYP(2) MAX UNIT
VIK Input clamp voltage VCC = MIN, II = –18mA –1.5 V
VOH High-level output voltage VCC = MIN, IOH = –20mA 2.5 V
VOL Low-level output voltage VCC = MIN, IOL = 20mA 0.5 V
VO Output voltage VCC = MAX, IO = 0 0 6 V
|VOD1| Differential output voltage VCC = MIN, IO = 0 1.5 6 V
|VOD2| Differential output voltage RL = 100Ω, See Figure 6-1 1/2 VOD1 or 2(3) V
∆|VOD| Change in magnitude of differential output voltage(4) RL = 100Ω, See Figure 6-1 ±0.2 V
VOC Common-mode output voltage(5) RL = 100Ω, See Figure 6-1 ±3 V
∆|VOC| Change in magnitude of common-mode output voltage(4) RL = 100Ω, See Figure 6-1 ±0.2 V
IO Output current with power off VCC = 0 VO = 6V 100
VO = –0.25V –100 µA
IOZ Off state (high impedance state) output current VCC = MAX VO = 0.5V –20
VO = 2.5V 20 µA
II Input current at maximum input voltage VCC = MAX, VI = 7V 100 µA
IIH High-level input current VCC = MAX, VI = 2.7V 20 µA
IIL Low-level input current VCC = MAX, VI = 0.4V –200 µA
IOS Short-circuit output current(6) VCC = MAX –30 –150 mA
ICC Supply current (all drivers) VCC = MAX, All outputs disabled 26 45 mA
(1) For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
(2) All typical values are at VCC = 5 V and TA = 25°C.
(3) The minimum VOD2 with a 100-Ω load is either 1/2 VOD1 or 2 V, whichever is greater.
(4) |VOD| and |VOC| are the changes in magnitude of VOD and VOC, respectively, that occur when the input is changed from a high level to a low level.
(5) In ANSI Standard EIA/TIA-422-B, VOC, which is the average of the two output voltages with respect to ground, is called output offset voltage, VOS.
(6) Not more than one output should be shorted at a time, and duration of the short circuit should not exceed one second.