SWCU193A April   2023  â€“ August 2024 CC2340R2 , CC2340R5 , CC2340R5-Q1

 

  1.   1
  2.   Read This First
    1.     About This Manual
    2.     Devices
    3.     Register, Field, and Bit Calls
    4.     Related Documentation
    5.     Trademarks
  3. 1 Architectural Overview
    1. 1.1  Target Applications
    2. 1.2  Introduction
    3. 1.3  Arm Cortex M0+
      1. 1.3.1 Processor Core
      2. 1.3.2 SysTick Timer
      3. 1.3.3 Nested Vectored Interrupt Controller
      4. 1.3.4 System Control Block (SCB)
    4. 1.4  On-Chip Memory
      1. 1.4.1 SRAM
      2. 1.4.2 Flash
      3. 1.4.3 ROM
    5. 1.5  Power Supply System
      1. 1.5.1 VDDS
      2. 1.5.2 VDDR
      3. 1.5.3 VDDD Digital Core Supply
      4. 1.5.4 DC/DC Converter
    6. 1.6  Radio
    7. 1.7  AES 128-bit Cryptographic Accelerator
    8. 1.8  System Timer (SYSTIM)
    9. 1.9  General Purpose Timers (LGPT)
    10. 1.10 Always-ON (AON) or Ultra-Low Leakage (ULL) Domain
      1. 1.10.1 Watchdog Timer
      2. 1.10.2 Battery and Temperature Monitor
      3. 1.10.3 Real-time Clock (RTC)
      4. 1.10.4 Low Power Comparator
    11. 1.11 Direct Memory Access
    12. 1.12 System Control and Clock
    13. 1.13 Communication Peripherals
      1. 1.13.1 UART
      2. 1.13.2 I2C
      3. 1.13.3 SPI
    14. 1.14 Programmable I/Os
    15. 1.15 Serial Wire Debug (SWD)
  4. 2  Arm Cortex-M0+ Processor
    1. 2.1 Introduction
    2. 2.2 Block Diagram
    3. 2.3 Overview
      1. 2.3.1 Peripherals
      2. 2.3.2 Programmer's Model
      3. 2.3.3 Instruction Set Summary
      4. 2.3.4 Memory Model
    4. 2.4 Registers
      1. 2.4.1 BPU Registers
      2. 2.4.2 CPU_ROM_TABLE Registers
      3. 2.4.3 DCB Registers
      4. 2.4.4 SCB Registers
      5. 2.4.5 SCSCS Registers
      6. 2.4.6 NVIC Registers
      7. 2.4.7 SYSTICK Registers
  5. 3 Memory Map
    1. 3.1 Memory Map
  6. 4 Interrupts and Events
    1. 4.1 Exception Model
      1. 4.1.1 Exception States
      2. 4.1.2 Exception Types
      3. 4.1.3 Exception Handlers
      4. 4.1.4 Vector Table
      5. 4.1.5 Exception Priorities
      6. 4.1.6 Exception Entry and Return
        1. 4.1.6.1 Exception Entry
        2. 4.1.6.2 Exception Return
    2. 4.2 Fault Handling
      1. 4.2.1 Lockup
    3. 4.3 Event Fabric
      1. 4.3.1 Introduction
      2. 4.3.2 Overview
      3. 4.3.3 Registers
      4. 4.3.4 AON Event Fabric
        1. 4.3.4.1 AON Common Input Events List
        2. 4.3.4.2 AON Event Subscribers
        3. 4.3.4.3 Power Management Controller (PMCTL)
        4. 4.3.4.4 Real Time Clock (RTC)
        5. 4.3.4.5 AON to MCU Event Fabric
      5. 4.3.5 MCU Event Fabric
        1. 4.3.5.1 Common Input Event List
        2. 4.3.5.2 MCU Event Subscribers
          1. 4.3.5.2.1 System CPU
          2. 4.3.5.2.2 Non-Maskable Interrupt (NMI)
    4. 4.4 Digital Test Bus (DTB)
    5. 4.5 EVTULL Registers
    6. 4.6 EVTSVT Registers
  7. 5 Debug Subsystem
    1. 5.1  Introduction
    2. 5.2  Block Diagram
    3. 5.3  Overview
      1. 5.3.1 Physical Interface
      2. 5.3.2 Debug Access Ports
    4. 5.4  Debug Features
      1. 5.4.1 Processor Debug
      2. 5.4.2 Breakpoint Unit (BPU)
      3. 5.4.3 Peripheral Debug
    5. 5.5  Behavior in Low Power Modes
    6. 5.6  Restricting Debug Access
    7. 5.7  Mailbox (DSSM)
    8. 5.8  Mailbox Events
      1. 5.8.1 CPU Interrupt Event (AON_DBG_COMB)
    9. 5.9  Software Considerations
    10. 5.10 DBGSS Registers
  8. 6 Power, Reset, and Clocking
    1. 6.1  Introduction
    2. 6.2  System CPU Modes
    3. 6.3  Supply System
      1. 6.3.1 Internal DC/DC Converter and Global LDO
    4. 6.4  Power States
      1. 6.4.1 Reset
      2. 6.4.2 Shutdown
      3. 6.4.3 Active
      4. 6.4.4 Idle
      5. 6.4.5 Standby
    5. 6.5  Digital Power Partitioning
    6. 6.6  Clocks
      1. 6.6.1 CLKSVT
      2. 6.6.2 CLKULL
    7. 6.7  Resets
      1. 6.7.1 Watchdog Timer (WDT)
      2. 6.7.2 LF Loss Detection
    8. 6.8  AON (REG3V3) Register Bank
    9. 6.9  CKMD Registers
    10. 6.10 CLKCTL Registers
    11. 6.11 PMCTL Registers
  9. 7 Internal Memory
    1. 7.1 SRAM
    2. 7.2 VIMS
      1. 7.2.1 Introduction
      2. 7.2.2 Block Diagram
      3. 7.2.3 Cache
        1. 7.2.3.1 Basic Cache Mechanism
        2. 7.2.3.2 Cache Prefetch Mechanism
        3. 7.2.3.3 Cache Micro-Prediction Mechanism
      4. 7.2.4 Flash
        1. 7.2.4.1 Flash Read-Only Protection
        2. 7.2.4.2 Flash Memory Programming
      5. 7.2.5 ROM
    3. 7.3 VIMS Registers
    4. 7.4 FLASH Registers
  10. 8 Device Boot and Bootloader
    1. 8.1 Device Boot and Programming
      1. 8.1.1 Boot Flow
      2. 8.1.2 Boot Timing
      3. 8.1.3 Boot Status
      4. 8.1.4 Boot Protection/Locking Mechanisms
      5. 8.1.5 Debug and Active SWD Connections at Boot
      6. 8.1.6 Flashless Test Mode and Tools Client Mode
        1. 8.1.6.1 Flashless Test Mode
        2. 8.1.6.2 Tools Client Mode
      7. 8.1.7 Retest Mode and Return-to-Factory Procedure
      8. 8.1.8 Disabling SWD Debug Port
    2. 8.2 Flash Programming
      1. 8.2.1 CCFG
      2. 8.2.2 CCFG Permissions/Restrictions that Affect Flash Programming
      3. 8.2.3 SACI Flash Programming Commands
      4. 8.2.4 Flash Programming Flows
        1. 8.2.4.1 Initial Programming of a New Device
        2. 8.2.4.2 Reprogramming of Previously Programmed Device
        3. 8.2.4.3 Add User Record on Already Programmed Device as Part of Commissioning Step
        4. 8.2.4.4 Incrementally Program Ancillary Data to MAIN Flash Sectors of a Previously Programmed Device
        5. 8.2.4.5 Debug Flow Charts
    3. 8.3 Device Management Command Interface
      1. 8.3.1 SACI Communication Protocol
        1. 8.3.1.1 Host Side Protocol
        2. 8.3.1.2 Command Format
        3. 8.3.1.3 Response Format
        4. 8.3.1.4 Response Result Field
        5. 8.3.1.5 Command Sequence Tag
        6. 8.3.1.6 Host Side Timeout
      2. 8.3.2 SACI Commands
        1. 8.3.2.1 Miscellaneous Commands
          1. 8.3.2.1.1 SACI_CMD_MISC_NO_OPERATION
          2. 8.3.2.1.2 SACI_CMD_MISC_GET_DIE_ID
          3. 8.3.2.1.3 SACI_CMD_MISC_GET_CCFG_USER_REC
        2. 8.3.2.2 Debug Commands
          1. 8.3.2.2.1 SACI_CMD_DEBUG_REQ_PWD_ID
          2. 8.3.2.2.2 SACI_CMD_DEBUG_SUBMIT_AUTH
          3. 8.3.2.2.3 SACI_CMD_DEBUG_EXIT_SACI_HALT
          4. 8.3.2.2.4 SACI_CMD_DEBUG_EXIT_SACI_SHUTDOWN
          5. 8.3.2.2.5 SACI_CMD_BLDR_APP_RESET_DEVICE
          6. 8.3.2.2.6 SACI_CMD_BLDR_APP_EXIT_SACI_RUN
        3. 8.3.2.3 Flash Programming Commands
          1. 8.3.2.3.1 SACI_CMD_FLASH_ERASE_CHIP
          2. 8.3.2.3.2 SACI_CMD_FLASH_PROG_CCFG_SECTOR
          3. 8.3.2.3.3 SACI_CMD_FLASH_PROG_CCFG_USER_REC
          4. 8.3.2.3.4 SACI_CMD_FLASH_PROG_MAIN_SECTOR
          5. 8.3.2.3.5 SACI_CMD_FLASH_PROG_MAIN_PIPELINED
          6. 8.3.2.3.6 SACI_CMD_FLASH_VERIFY_MAIN_SECTORS
          7. 8.3.2.3.7 SACI_CMD_FLASH_VERIFY_CCFG_SECTOR
    4. 8.4 Bootloader Support
      1. 8.4.1 Bootloader Parameters
      2. 8.4.2 Persistent State
      3. 8.4.3 User-Defined Bootloader Guidelines
    5. 8.5 ROM Serial Bootloader
      1. 8.5.1 ROM Serial Bootloader Interfaces
        1. 8.5.1.1 Packet Handling
          1. 8.5.1.1.1 Packet Acknowledge and Not-Acknowledge Bytes
        2. 8.5.1.2 Transport Layer
          1. 8.5.1.2.1 UART Transport
            1. 8.5.1.2.1.1 UART Baud Rate Automatic Detection
          2. 8.5.1.2.2 SPI Transport
      2. 8.5.2 ROM Serial Bootloader Parameters
      3. 8.5.3 ROM Serial Bootloader Commands
        1. 8.5.3.1 BLDR_CMD_PING
        2. 8.5.3.2 BLDR_CMD_GET_STATUS
        3. 8.5.3.3 BLDR_CMD_GET_PART_ID
        4. 8.5.3.4 BLDR_CMD_RESET
        5. 8.5.3.5 BLDR_CMD_CHIP_ERASE
        6. 8.5.3.6 BLDR_CMD_CRC32
        7. 8.5.3.7 BLDR_CMD_DOWNLOAD
        8. 8.5.3.8 BLDR_CMD_DOWNLOAD_CRC
        9. 8.5.3.9 BLDR_CMD_SEND_DATA
      4. 8.5.4 Bootloader Firmware Update Example
  11. 9 Device Configuration
    1. 9.1 Factory Configuration (FCFG)
    2. 9.2 Customer Configuration (CCFG)
  12. 10General Purpose Timers (LGPT)
    1. 10.1 Overview
    2. 10.2 Block Diagram
    3. 10.3 Functional Description
      1. 10.3.1  Prescaler
      2. 10.3.2  Counter
      3. 10.3.3  Target
      4. 10.3.4  Channel Input Logic
      5. 10.3.5  Channel Output Logic
      6. 10.3.6  Channel Actions
        1. 10.3.6.1 Period and Pulse Width Measurement
        2. 10.3.6.2 Clear on Zero, Toggle on Compare Repeatedly
        3. 10.3.6.3 Set on Zero, Toggle on Compare Repeatedly
      7. 10.3.7  Channel Capture Configuration
      8. 10.3.8  Channel Filters
        1. 10.3.8.1 Setting up the Channel Filters
      9. 10.3.9  Synchronize Multiple LGPT Timers
      10. 10.3.10 Interrupts, ADC Trigger, and DMA Request
    4. 10.4 Timer Modes
      1. 10.4.1 Quadrature Decoder
      2. 10.4.2 DMA
      3. 10.4.3 IR Generation
      4. 10.4.4 Fault and Park
      5. 10.4.5 Deadband
      6. 10.4.6 Deadband, Fault, and Park
      7. 10.4.7 Example Application: Brushless DC (BLDC) Motor
    5. 10.5 LGPT0 Registers
    6. 10.6 LGPT1 Registers
    7. 10.7 LGPT2 Registers
    8. 10.8 LGPT3 Registers
  13. 11System Timer (SYSTIM)
    1. 11.1 Overview
    2. 11.2 Block Diagram
    3. 11.3 Functional Description
      1. 11.3.1 Common Channel Features
        1. 11.3.1.1 Compare Mode
        2. 11.3.1.2 Capture Mode
        3. 11.3.1.3 Additional Channel Arming Methods
      2. 11.3.2 Interrupts and Events
    4. 11.4 SYSTIM Registers
  14. 12Real Time Clock (RTC)
    1. 12.1 Introduction
    2. 12.2 Block Diagram
    3. 12.3 Interrupts and Events
      1. 12.3.1 Input Event
      2. 12.3.2 Output Event
      3. 12.3.3 Arming and Disarming Channels
    4. 12.4 Capture and Compare Configuration
      1. 12.4.1 Capture
      2. 12.4.2 Compare
    5. 12.5 RTC Registers
  15. 13Low Power Comparator and SYS0
    1. 13.1 Introduction
    2. 13.2 Block Diagram
    3. 13.3 Functional Description
      1. 13.3.1 Input Selection
      2. 13.3.2 Voltage Divider
      3. 13.3.3 Hysteresis
      4. 13.3.4 Wake-Up
    4. 13.4 SYS0 Registers
  16. 14Battery Monitor, Temperature Sensor, and DCDC Controller (PMUD)
    1. 14.1 Introduction
    2. 14.2 Functional Description
      1. 14.2.1 BATMON
      2. 14.2.2 DCDC
    3. 14.3 PMUD Registers
  17. 15Micro Direct Memory Access (µDMA)
    1. 15.1 Introduction
    2. 15.2 Block Diagram
    3. 15.3 Functional Description
      1. 15.3.1  Channel Assignments
      2. 15.3.2  Priority
      3. 15.3.3  Arbitration Size
      4. 15.3.4  Request Types
        1. 15.3.4.1 Single Request
        2. 15.3.4.2 Burst Request
      5. 15.3.5  Channel Configuration
      6. 15.3.6  Transfer Modes
        1. 15.3.6.1 Stop Mode
        2. 15.3.6.2 Basic Mode
        3. 15.3.6.3 Auto Mode
        4. 15.3.6.4 Ping-Pong Mode
        5. 15.3.6.5 Memory Scatter-Gather Mode
        6. 15.3.6.6 Peripheral Scatter-Gather Mode
      7. 15.3.7  Transfer Size and Increments
      8. 15.3.8  Peripheral Interface
      9. 15.3.9  Software Request
      10. 15.3.10 Interrupts and Errors
      11. 15.3.11 Initialization and Configuration
        1. 15.3.11.1 Module Initialization
        2. 15.3.11.2 Configuring a Memory-to-Memory Transfer
        3. 15.3.11.3 Configure the Channel Attributes
        4. 15.3.11.4 Configure the Channel Control Structure
        5. 15.3.11.5 Start the Transfer
        6. 15.3.11.6 Software Considerations
    4. 15.4 DMA Registers
  18. 16Advanced Encryption Standard (AES)
    1. 16.1 Introduction
      1. 16.1.1 AES Performance
    2. 16.2 Functional Description
      1. 16.2.1 Reset Considerations
      2. 16.2.2 Interrupt and Event Support
        1. 16.2.2.1 Interrupt Events and Requests
        2. 16.2.2.2 Connection to Event Fabric
      3. 16.2.3 µDMA
        1. 16.2.3.1 µDMA Example
    3. 16.3 Encryption and Decryption Configuration
      1. 16.3.1  CBC-MAC (Cipher Block Chaining-Message Authentication Code)
      2. 16.3.2  CBC (Cipher Block Chaining) Encryption
      3. 16.3.3  CBC Decryption
      4. 16.3.4  CTR (Counter) Encryption/Decryption
      5. 16.3.5  ECB (Electronic Code Book) Encryption
      6. 16.3.6  ECB Decryption
      7. 16.3.7  CFB (Cipher Feedback) Encryption
      8. 16.3.8  CFB Decryption
      9. 16.3.9  OFB (Open Feedback) Encryption
      10. 16.3.10 OFB Decryption
      11. 16.3.11 PCBC (Propagating Cipher Block Chaining) Encryption
      12. 16.3.12 PCBC Decryption
      13. 16.3.13 CTR-DRBG (Counter-Deterministic Random Bit Generator)
      14. 16.3.14 CCM
    4. 16.4 AES Registers
  19. 17Analog to Digital Converter (ADC)
    1. 17.1 Overview
    2. 17.2 Block Diagram
    3. 17.3 Functional Description
      1. 17.3.1  ADC Core
      2. 17.3.2  Voltage Reference Options
      3. 17.3.3  Resolution Modes
      4. 17.3.4  ADC Clocking
      5. 17.3.5  Power-Down Behavior
      6. 17.3.6  Sampling Trigger Sources and Sampling Modes
        1. 17.3.6.1 AUTO Sampling Mode
        2. 17.3.6.2 MANUAL Sampling Mode
      7. 17.3.7  Sampling Period
      8. 17.3.8  Conversion Modes
      9. 17.3.9  ADC Data Format
      10. 17.3.10 Status Register
      11. 17.3.11 ADC Events
        1. 17.3.11.1 CPU Interrupt Event Publisher (INT_EVENT0)
        2. 17.3.11.2 Generic Event Publisher (INT_EVENT1)
        3. 17.3.11.3 DMA Trigger Event Publisher (INT_EVENT2)
        4. 17.3.11.4 Generic Event Subscriber
    4. 17.4 Advanced Features
      1. 17.4.1 Window Comparator
      2. 17.4.2 DMA and FIFO Operation
        1. 17.4.2.1 DMA/CPU Operation in Non-FIFO Mode (FIFOEN=0)
        2. 17.4.2.2 DMA/CPU Operation in FIFO Mode (FIFOEN=1)
        3. 17.4.2.3 DMA/CPU Operation Summary Matrix
      3. 17.4.3 Ad-Hoc Single Conversion
    5. 17.5 ADC Registers
  20. 18I/O Controller (IOC)
    1. 18.1  Introduction
    2. 18.2  Block Diagram
    3. 18.3  I/O Mapping and Configuration
      1. 18.3.1 Basic I/O Mapping
      2. 18.3.2 Radio GPO
      3. 18.3.3 Pin Mapping
      4. 18.3.4 DTB Muxing
    4. 18.4  Edge Detection
    5. 18.5  GPIO
    6. 18.6  I/O Pins
    7. 18.7  Unused Pins
    8. 18.8  Debug Configuration
    9. 18.9  IOC Registers
    10. 18.10 GPIO Registers
  21. 19Universal Asynchronous Receiver/Transmitter (UART)
    1. 19.1 Introduction
    2. 19.2 Block Diagram
    3. 19.3 Functional Description
      1. 19.3.1 Transmit and Receive Logic
      2. 19.3.2 Baud Rate Generation
      3. 19.3.3 FIFO Operation
        1. 19.3.3.1 FIFO Remapping
      4. 19.3.4 Data Transmission
      5. 19.3.5 Flow Control
      6. 19.3.6 IrDA Encoding and Decoding
      7. 19.3.7 Interrupts
      8. 19.3.8 Loopback Operation
    4. 19.4 Interface to µDMA
    5. 19.5 Initialization and Configuration
    6. 19.6 UART Registers
  22. 20Serial Peripheral Interface (SPI)
    1. 20.1 Overview
      1. 20.1.1 Features
      2. 20.1.2 Block Diagram
    2. 20.2 Signal Description
    3. 20.3 Functional Description
      1. 20.3.1  Clock Control
      2. 20.3.2  FIFO Operation
        1. 20.3.2.1 Transmit FIFO
        2. 20.3.2.2 Repeated Transmit Operation
        3. 20.3.2.3 Receive FIFO
        4. 20.3.2.4 FIFO Flush
      3. 20.3.3  Interrupts
      4. 20.3.4  Data Format
      5. 20.3.5  Delayed Data Sampling
      6. 20.3.6  Chip Select Control
      7. 20.3.7  Command Data Control
      8. 20.3.8  Protocol Descriptions
        1. 20.3.8.1 Motorola SPI Frame Format
        2. 20.3.8.2 Texas Instruments Synchronous Serial Frame Format
        3. 20.3.8.3 MICROWIRE Frame Format
      9. 20.3.9  CRC Configuration
      10. 20.3.10 Auto CRC Functionality
      11. 20.3.11 Auto Header Functionality
      12. 20.3.12 SPI Status
      13. 20.3.13 Debug Halt
    4. 20.4 µDMA Operation
    5. 20.5 Initialization and Configuration
    6. 20.6 SPI Registers
  23. 21Inter-Integrated Circuit (I2C)
    1. 21.1 Introduction
    2. 21.2 Block Diagram
    3. 21.3 Functional Description
      1. 21.3.1 Functional Overview
        1. 21.3.1.1 Start and Stop Conditions
        2. 21.3.1.2 Data Format with 7-Bit Address
        3. 21.3.1.3 Data Validity
        4. 21.3.1.4 Acknowledge
        5. 21.3.1.5 Arbitration
      2. 21.3.2 Available Speed Modes
      3. 21.3.3 Interrupts
        1. 21.3.3.1 I2C Controller Interrupts
        2. 21.3.3.2 I2C Target Interrupts
      4. 21.3.4 Loopback Operation
      5. 21.3.5 Command Sequence Flow Charts
        1. 21.3.5.1 I2C Controller Command Sequences
        2. 21.3.5.2 I2C Target Command Sequences
    4. 21.4 Initialization and Configuration
    5. 21.5 I2C Registers
  24. 22Radio
    1. 22.1 Introduction
    2. 22.2 Block Diagram
    3. 22.3 Overview
      1. 22.3.1 Radio Sub-Domains
      2. 22.3.2 Radio RAMs
      3. 22.3.3 Doorbell (DBELL)
        1. 22.3.3.1 Interrupts
        2. 22.3.3.2 GPIO Control
        3. 22.3.3.3 SYSTIM Interface
    4. 22.4 Radio Usage Model
      1. 22.4.1 CRC and Whitening
    5. 22.5 LRFDDBELL Registers
    6. 22.6 LRFDRXF Registers
    7. 22.7 LRFDTXF Registers
  25. 23Revision History

6.10 CLKCTL Registers

Table 6-58 lists the memory-mapped registers for the CLKCTL registers. All register offset addresses not listed in Table 6-58 should be considered as reserved locations and the register contents should not be modified.

Table 6-58 CLKCTL Registers
OffsetAcronymRegister NameSection
0hDESCDescription Register.Go
4hDESCEX0Extended Description Register 0.Go
8hDESCEX1Extended Description Register 1.Go
ChCLKCFG0Clock Configuration Register 0.Go
10hCLKCFG1Clock Configuration Register 1.Go
14hCLKENSET0Clock Enable Set Register 0.Go
18hCLKENSET1Clock Enable Set Register 1.Go
20hCLKENCLR0Clock Enable Clear Register 0.Go
24hCLKENCLR1Clock Enable Clear Register 1.Go
3ChSTBYPTRInternal. Only to be used through TI provided API.Go
48hIDLECFGIDLE Configuration Register.Go

Complex bit access types are encoded to fit into small table cells. Table 6-59 shows the codes that are used for access types in this section.

Table 6-59 CLKCTL Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
Write Type
WWWrite
Reset or Default Value
-nValue after reset or the default value

6.10.1 DESC Register (Offset = 0h) [Reset = 25480000h]

DESC is shown in Table 6-60.

Return to the Summary Table.

Description Register.
This register provides IP module ID, revision information, instance index and standard MMR registers offset.

Table 6-60 DESC Register Field Descriptions
BitFieldTypeResetDescription
31-16MODIDR2548hModule identifier used to uniquely identify this IP.
15-12STDIPOFFR0hStandard IP MMR block offset. Standard IP MMRs are the set of from aggregated IRQ registers till DTB.
0: Standard IP MMRs do not exist
0x1-0xF: Standard IP MMRs begin at offset of (64*STDIPOFF from the base IP address)
11-8INSTIDXR0hIP Instance ID number. If multiple instances of IP exist in the device, this field can identify the instance number (0-15).
7-4MAJREVR0hMajor revision of IP 0-15
3-0MINREVR0hMinor revision of IP 0-15.

6.10.2 DESCEX0 Register (Offset = 4h) [Reset = 78034447h]

DESCEX0 is shown in Table 6-61.

Return to the Summary Table.

Extended Description Register 0.
This register shows SVT IP availability, HW features and memory size configuration.

Table 6-61 DESCEX0 Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR0hReserved
30LGPT3R1hIP status on device
0h = IP is unavailable
1h = IP is available
29LGPT2R1hIP status on device
0h = IP is unavailable
1h = IP is available
28LGPT1R1hIP status on device
0h = IP is unavailable
1h = IP is available
27LGPT0R1hIP status on device
0h = IP is unavailable
1h = IP is available
26-18RESERVEDR0hReserved
17DMAR1hIP status on device
0h = IP is unavailable
1h = IP is available
16LAESR1hIP status on device
0h = IP is unavailable
1h = IP is available
15RESERVEDR0hReserved
14ADC0R1hIP status on device
0h = IP is unavailable
1h = IP is available
13-11RESERVEDR0hReserved
10SPI0R1hIP status on device
0h = IP is unavailable
1h = IP is available
9-7RESERVEDR0hReserved
6I2C0R1hIP status on device
0h = IP is unavailable
1h = IP is available
5-3RESERVEDR0hReserved
2UART0R1hIP status on device
0h = IP is unavailable
1h = IP is available
1LRFDR1hIP status on device
0h = IP is unavailable
1h = IP is available
0GPIOR1hIP status on device
0h = IP is unavailable
1h = IP is available

6.10.3 DESCEX1 Register (Offset = 8h) [Reset = F000FF00h]

DESCEX1 is shown in Table 6-62.

Return to the Summary Table.

Extended Description Register 1.
This register shows SVT IP availability, HW features and memory size configuration.

Table 6-62 DESCEX1 Register Field Descriptions
BitFieldTypeResetDescription
31-30FLASHSZR3hSystem flash availability
0h = Flash size set to level 0 (Min size)
1h = Flash size set to level 1
2h = Flash size set to level 2
3h = Flash size set to level 3 (Max size)
29-28SRAMSZR3hSystem SRAM availability
0h = SRAM size set to level 0 (Min size)
1h = SRAM size set to level 1
2h = SRAM size set to level 2
3h = SRAM size set to level 3 (Max size)
27-16RESERVEDR0hReserved
15-8ROPTRFFhSystem radio feature availability
FFh = All features available
7-0RESERVEDR0hReserved

6.10.4 CLKCFG0 Register (Offset = Ch) [Reset = 00000001h]

CLKCFG0 is shown in Table 6-63.

Return to the Summary Table.

Clock Configuration Register 0.
This register shows the IP clock configuration for the system.
The configuration is updated through CLKENSET0 and CLKENCLR0.

Table 6-63 CLKCFG0 Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR0hReserved
30LGPT3R0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
29LGPT2R0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
28LGPT1R0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
27LGPT0R0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
26-18RESERVEDR0hReserved
17DMAR0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
16LAESR0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
15RESERVEDR0hReserved
14ADC0R0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
13-11RESERVEDR0hReserved
10SPI0R0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
9-7RESERVEDR0hReserved
6I2C0R0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
5-3RESERVEDR0hReserved
2UART0R0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
1LRFDR0hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled
0GPIOR1hIP clock configuration
0h = Clock is disabled
1h = Clock is enabled

6.10.5 CLKCFG1 Register (Offset = 10h) [Reset = 00000000h]

CLKCFG1 is shown in Table 6-64.

Return to the Summary Table.

Clock Configuration Register 1.
This register shows the IP clock configuration for the system.
The configuration is updated through CLKENSET1 and CLKENCLR1.

Table 6-64 CLKCFG1 Register Field Descriptions
BitFieldTypeResetDescription
31-0RESERVEDR0hReserved

6.10.6 CLKENSET0 Register (Offset = 14h) [Reset = 00000000h]

CLKENSET0 is shown in Table 6-65.

Return to the Summary Table.

Clock Enable Set Register 0.
This register enables IP clocks in the system.
Used to set the corresponding fields in CLKCFG0 to 1.

Table 6-65 CLKENSET0 Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR0hReserved
30LGPT3W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
29LGPT2W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
28LGPT1W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
27LGPT0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
26-18RESERVEDR0hReserved
17DMAW0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
16LAESW0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
15RESERVEDR0hReserved
14ADC0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
13-11RESERVEDR0hReserved
10SPI0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
9-7RESERVEDR0hReserved
6I2C0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
5-3RESERVEDR0hReserved
2UART0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
1LRFDW0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable
0GPIOW0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Set IP clock enable

6.10.7 CLKENSET1 Register (Offset = 18h) [Reset = 00000000h]

CLKENSET1 is shown in Table 6-66.

Return to the Summary Table.

Clock Enable Set Register 1.
This register enables IP clocks in the system.
Used to set the corresponding fields in CLKCFG1 to 1.

Table 6-66 CLKENSET1 Register Field Descriptions
BitFieldTypeResetDescription
31-0RESERVEDR0hReserved

6.10.8 CLKENCLR0 Register (Offset = 20h) [Reset = 00000000h]

CLKENCLR0 is shown in Table 6-67.

Return to the Summary Table.

Clock Enable Clear Register 0.
This register disables IP clocks in the system.
Used to clear the corresponding fields in CLKCFG0 to 0.

Table 6-67 CLKENCLR0 Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR0hReserved
30LGPT3W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
29LGPT2W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
28LGPT1W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
27LGPT0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
26-18RESERVEDR0hReserved
17DMAW0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
16LAESW0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
15RESERVEDR0hReserved
14ADC0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
13-11RESERVEDR0hReserved
10SPI0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
9-7RESERVEDR0hReserved
6I2C0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
5-3RESERVEDR0hReserved
2UART0W0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
1LRFDW0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable
0GPIOW0hConfigure IP clock enable
0h = IP clock enable is unchanged
1h = Clear IP clock enable

6.10.9 CLKENCLR1 Register (Offset = 24h) [Reset = 00000000h]

CLKENCLR1 is shown in Table 6-68.

Return to the Summary Table.

Clock Enable Clear Register 1.
This register disables IP clocks in the system.
Used to clear the corresponding fields in CLKCFG1 to 0.

Table 6-68 CLKENCLR1 Register Field Descriptions
BitFieldTypeResetDescription
31-0RESERVEDR0hReserved

6.10.10 STBYPTR Register (Offset = 3Ch) [Reset = 00000000h]

STBYPTR is shown in Table 6-69.

Return to the Summary Table.

Internal. Only to be used through TI provided API.

Table 6-69 STBYPTR Register Field Descriptions
BitFieldTypeResetDescription
31-0VALR/W0hInternal. Only to be used through TI provided API.

6.10.11 IDLECFG Register (Offset = 48h) [Reset = 00000000h]

IDLECFG is shown in Table 6-70.

Return to the Summary Table.

IDLE Configuration Register.
This register contains flash LDO configuration for IDLE mode.

Table 6-70 IDLECFG Register Field Descriptions
BitFieldTypeResetDescription
31-1RESERVEDR0hReserved
0MODER/W0hFlash LDO configuration in SLEEP/IDLE mode.
0h = Flash LDO is on in SLEEP/IDLE mode.
Gives fast wake up time from SLEEP/IDLE mode, but increased power consumption.
1h = Flash LDO is off in SLEEP/IDLE mode.
Decreases power consumption in SLEEP/IDLE mode, but gives longer wake up time.
Note: NVM clock is turned off independent of DMA status. Therefore SW must ensure that DMA never access NVM in this mode.