ZHCS779B March   2012  – December 2023 UCC28070A

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
    1. 4.1 Pin Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Interleaving
      2. 6.3.2  Programming the PWM Frequency and Maximum Duty-Cycle Clamp
      3. 6.3.3  Frequency Dithering (Magnitude and Rate)
      4. 6.3.4  External Clock Synchronization
      5. 6.3.5  Multi-phase Operation
      6. 6.3.6  VSENSE and VINAC Resistor Configuration
      7. 6.3.7  VSENSE and VINAC Open-Circuit Protection
      8. 6.3.8  Current Synthesizer
      9. 6.3.9  Programmable Peak Current Limit
      10. 6.3.10 Linear Multiplier and Quantized Voltage Feed Forward
      11. 6.3.11 Enhanced Transient Response (VA Slew-Rate Correction)
      12. 6.3.12 Voltage Biasing (VCC and VVREF)
      13. 6.3.13 PFC Enable and Disable
      14. 6.3.14 Adaptive Soft Start
      15. 6.3.15 PFC Start-Up Hold Off
      16. 6.3.16 Output Overvoltage Protection (OVP)
      17. 6.3.17 Zero-Power Detection
      18. 6.3.18 Thermal Shutdown
      19. 6.3.19 Current Loop Compensation
      20. 6.3.20 Voltage Loop Compensation
    4. 6.4 Device Functional Modes
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Output Current Calculation
        2. 7.2.2.2 Bridge Rectifier
        3. 7.2.2.3 PFC Inductor (L1 and L2)
        4. 7.2.2.4 PFC MOSFETs (M1 and M2)
        5. 7.2.2.5 PFC Diode
        6. 7.2.2.6 PFC Output Capacitor
        7. 7.2.2.7 Current-Loop Feedback Configuration (Sizing of the Current-Transformer Turns-Ratio and Sense Resistor (RS))
        8. 7.2.2.8 Current-Sense Offset and PWM Ramp for Improved Noise Immunity
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Documentation Support
      1. 8.1.1 Related Documentation
    2. 8.2 Community Resources
    3. 8.3 Trademarks
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

9 Revision History

Changes from Revision A (May 2016) to Revision B (December 2023)

  • 更新了整个文档中的印刷错误并澄清了文本Go
  • Moved Absolute Maximum values for Supply voltage and current, Gate-drive currents, and signal-pin Currents from MIN column to MAX column Go
  • Updated Y-axis units in several figuresGo
  • Added SYNC frequency limitation note in External Clock Synchronization sectionGo
  • Added paragraph on PKLMT sub-harmonic oscillationGo
  • Added clarifying equation for kSYNC in Current Loop Compensation section; corrected gain in Current Error Amplifier diagram and equation for Rzc. Go
  • Updated gain in Voltage Error Amplifier diagram Go
  • Updated text to clarify bridge rectifier design considerationsGo
  • Updated method for calculating boost inductanceGo
  • Added additional references to Related Documentation sectionGo

Changes from Revision * (May 2015) to Revision A (May 2016)

  • 添加了 器件信息 表、 修订历史记录部分、 引脚配置和功能 部分、 规格 部分、 详细说明 部分、 应用和实施 部分、 电源相关建议 部分、 布局 部分、 器件和文档支持 部分 以及机械、封装和可订购信息 部分 Go