ZHCSQ77A February   2023  – September 2023 TPS25948

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Electrical Characteristics
    5. 7.5 Timing Requirements
    6. 7.6 Switching Characteristics
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Undervoltage Lockout (UVLO and UVP)
      2. 8.3.2 Overvoltage Lockout (OVLO)
      3. 8.3.3 Inrush Current, Overcurrent, and Short Circuit Protection
        1. 8.3.3.1 Slew Rate (dVdt) and Inrush Current Control
        2. 8.3.3.2 Active Current Limiting
        3. 8.3.3.3 Short-Circuit Protection
      4. 8.3.4 Analog Load Current Monitor
      5. 8.3.5 Reverse Current Protection
      6. 8.3.6 Overtemperature Protection (OTP)
      7. 8.3.7 Fault Response and Indication (FLT)
      8. 8.3.8 Supply Good Indication (SPLYGD/SPLYGD)
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Single Device, Self-Controlled
    3. 9.3 Typical Application
      1. 9.3.1 Design Requirements
      2. 9.3.2 Detailed Design Procedure
        1. 9.3.2.1 Setting Overvoltage Threshold
        2. 9.3.2.2 Setting Output Voltage Rise Time (tR)
        3. 9.3.2.3 Setting Overcurrent Threshold (ILIM)
        4. 9.3.2.4 Setting Overcurrent Blanking Interval (tITIMER)
      3. 9.3.3 Application Curves
    4. 9.4 Active ORing
    5. 9.5 Priority Power MUXing
    6. 9.6 Parallel Operation
    7. 9.7 USB PD Port Protection
    8. 9.8 Power Supply Recommendations
      1. 9.8.1 Transient Protection
      2. 9.8.2 Output Short-Circuit Measurements
    9. 9.9 Layout
      1. 9.9.1 Layout Guidelines
      2. 9.9.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 接收文档更新通知
    3. 10.3 支持资源
    4. 10.4 Trademarks
    5. 10.5 静电放电警告
    6. 10.6 术语表
  12. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
Parameter Pin MIN MAX UNIT
VIN Input voltage range IN 2.7 23 V
VOUT Output voltage range OUT min (23, VIN + 20) V
VEN/UVLO Enable pin voltage range EN/UVLO 5(1) V
VOVLO OVLO pin voltage range OVLO 0.5 1.5 V
VdVdt dVdT capacitor voltage rating dVdt VIN + 5 V(2) V
VRCBCTRL RCBCTRL pin voltage range  RCBCTRL 5 V
VFLTB FLTB pin voltage range FLTB 5 V
VSPLYGD SPLYGD/SPLYGD pin voltage range SPLYGD/SPLYGD 5 V
VITIMER ITIMER pin capacitor voltage rating ITIMER 4 V
RILM ILM pin resistance ILM 536 4834 Ω
ILOAD Continuous switch current, TJ ≤ 125℃ IN to OUT or OUT to IN 8 A
TJ Junction temperature –40 125 °C
(1) For supply voltages below 5 V, it is okay to pull up the EN pin to IN directly. For supply voltages greater than 5 V, it is recommended to use a resistor divider to step down the voltage. 
(2) In a PowerMUX scenario with unequal supplies, the dVdt capacitor rating for each device should be chosen based on the highest of the 2 rails.