ZHCSMY2 December   2020 PCM6480-Q1

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics
    6. 7.6  Timing Requirements: I2C Interface
    7. 7.7  Switching Characteristics: I2C Interface
    8. 7.8  Timing Requirements: SPI Interface
    9. 7.9  Switching Characteristics: SPI Interface
    10. 7.10 Timing Requirements: TDM, I2S or LJ Interface
    11. 7.11 Switching Characteristics: TDM, I2S or LJ Interface
    12. 7.12 Timing Requirements: PDM Digital Microphone Interface
    13. 7.13 Switching Characteristics: PDM Digial Microphone Interface
    14. 7.14 Timing Diagrams
    15. 7.15 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Serial Interfaces
        1. 8.3.1.1 Control Serial Interfaces
        2. 8.3.1.2 Audio Serial Interfaces
          1. 8.3.1.2.1 Time Division Multiplexed Audio (TDM) Interface
          2. 8.3.1.2.2 Inter IC Sound (I2S) Interface
          3. 8.3.1.2.3 Left-Justified (LJ) Interface
        3. 8.3.1.3 Using Multiple Devices With Shared Buses
      2. 8.3.2  Phase-Locked Loop (PLL) and Clock Generation
      3. 8.3.3  Analog Input Channel Configuration
      4. 8.3.4  Reference Voltage
      5. 8.3.5  Microphone Bias
      6. 8.3.6  Input DC Fault Diagnostics
        1. 8.3.6.1 Fault Conditions
          1. 8.3.6.1.1 Input Pin Short to Ground
          2. 8.3.6.1.2 Input Pin Short to MICBIAS
          3. 8.3.6.1.3 Open Inputs
          4. 8.3.6.1.4 Short Between INxP and INxM
          5. 8.3.6.1.5 Input Pin Overvoltage
          6. 8.3.6.1.6 Input Pin Short to VBAT_IN
        2. 8.3.6.2 Fault Reporting
          1. 8.3.6.2.1 Overcurrent and Overtemperature Protection
      7. 8.3.7  Digital PDM Microphone Record Channel
      8. 8.3.8  Signal-Chain Processing
        1. 8.3.8.1 Programmable Channel Gain and Digital Volume Control
        2. 8.3.8.2 Programmable Channel Gain Calibration
        3. 8.3.8.3 Programmable Channel Phase Calibration
        4. 8.3.8.4 Programmable Digital High-Pass Filter
        5. 8.3.8.5 Programmable Digital Biquad Filters
        6. 8.3.8.6 Programmable Channel Summer and Digital Mixer
        7. 8.3.8.7 Configurable Digital Decimation Filters
          1. 8.3.8.7.1 Linear Phase Filters
            1. 8.3.8.7.1.1 Sampling Rate: 8 kHz or 7.35 kHz
            2. 8.3.8.7.1.2 Sampling Rate: 16 kHz or 14.7 kHz
            3. 8.3.8.7.1.3 Sampling Rate: 24 kHz or 22.05 kHz
            4. 8.3.8.7.1.4 Sampling Rate: 32 kHz or 29.4 kHz
            5. 8.3.8.7.1.5 Sampling Rate: 48 kHz or 44.1 kHz
            6. 8.3.8.7.1.6 Sampling Rate: 96 kHz or 88.2 kHz
            7. 8.3.8.7.1.7 Sampling Rate: 192 kHz or 176.4 kHz
            8. 8.3.8.7.1.8 Sampling Rate: 384 kHz or 352.8 kHz
            9. 8.3.8.7.1.9 Sampling Rate: 768 kHz or 705.6 kHz
          2. 8.3.8.7.2 Low-Latency Filters
            1. 8.3.8.7.2.1 Sampling Rate: 16 kHz or 14.7 kHz
            2. 8.3.8.7.2.2 Sampling Rate: 24 kHz or 22.05 kHz
            3. 8.3.8.7.2.3 Sampling Rate: 32 kHz or 29.4 kHz
            4. 8.3.8.7.2.4 Sampling Rate: 48 kHz or 44.1 kHz
            5. 8.3.8.7.2.5 Sampling Rate: 96 kHz or 88.2 kHz
            6. 8.3.8.7.2.6 Sampling Rate: 192 kHz or 176.4 kHz
          3. 8.3.8.7.3 Ultra-Low-Latency Filters
            1. 8.3.8.7.3.1 Sampling Rate: 16 kHz or 14.7 kHz
            2. 8.3.8.7.3.2 Sampling Rate: 24 kHz or 22.05 kHz
            3. 8.3.8.7.3.3 Sampling Rate: 32 kHz or 29.4 kHz
            4. 8.3.8.7.3.4 Sampling Rate: 48 kHz or 44.1 kHz
            5. 8.3.8.7.3.5 Sampling Rate: 96 kHz or 88.2 kHz
            6. 8.3.8.7.3.6 Sampling Rate: 192 kHz or 176.4 kHz
            7. 8.3.8.7.3.7 Sampling Rate: 384 kHz or 352.8 kHz
      9. 8.3.9  Automatic Gain Controller (AGC)
      10. 8.3.10 Interrupts, Status, and Digital I/O Pin Multiplexing
    4. 8.4 Device Functional Modes
      1. 8.4.1 Hardware Shutdown
      2. 8.4.2 Sleep Mode or Software Shutdown
      3. 8.4.3 Active Mode
      4. 8.4.4 Software Reset
    5. 8.5 Programming
      1. 8.5.1 Control Serial Interfaces
        1. 8.5.1.1 I2C Control Interface
          1. 8.5.1.1.1 General I2C Operation
          2. 8.5.1.1.2 I2C Single-Byte and Multiple-Byte Transfers
            1. 8.5.1.1.2.1 I2C Single-Byte Write
            2. 8.5.1.1.2.2 I2C Multiple-Byte Write
            3. 8.5.1.1.2.3 I2C Single-Byte Read
            4. 8.5.1.1.2.4 I2C Multiple-Byte Read
        2. 8.5.1.2 SPI Control Interface
    6. 8.6 Register Maps
      1. 8.6.1 Device Configuration Registers
        1. 8.6.1.1 Registers Access Type
        2. 8.6.1.2 Page 0 Registers
        3. 8.6.1.3 Page 1 Registers
      2. 8.6.2 Programmable Coefficient Registers
        1. 8.6.2.1 Programmable Coefficient Registers: Page 2
        2. 8.6.2.2 Programmable Coefficient Registers: Page 3
        3. 8.6.2.3 Programmable Coefficient Registers: Page 4
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Four-Channel Analog Microphone and Four-Channel PDM Microphone Simultaneous Recording Using the PCM6480-Q1
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Example Device Register Configuration Script for EVM Setup
        3. 9.2.1.3 Application Curves
    3. 9.3 What To Do and What Not To Do
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Development Support
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 接收文档更新通知
    4. 12.4 支持资源
    5. 12.5 Trademarks
    6. 12.6 静电放电警告
    7. 12.7 术语表
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.3.1.3 Using Multiple Devices With Shared Buses

The device has many supported features and flexible options that can be used in the system to seamlessly connect multiple PCM6480-Q1 devices by sharing a single common I2C control bus and an audio serial interface bus. This architecture enables multiple applications to be applied to a system that require a microphone array for beam-forming operation, hands-free in-vehicle communication, car cabin active noise cancellation, and so forth. Figure 8-14 shows a diagram of multiple PCM6480-Q1 devices in a configuration where the control and audio data buses are shared.

GUID-50657C35-003A-4437-990D-4917CF125BA8-low.gif Figure 8-14 Multiple PCM6480-Q1 Devices With Shared Control and Audio Data Buses

The PCM6480-Q1 consist of the following features to enable seamless connection and interaction of multiple devices using a shared bus:

  • Supports up to four pin-programmable I2C slave addresses
  • I2C broadcast simultaneously writes to (or triggers) all PCM6480-Q1 devices
  • Supports up to 64 configuration output channel slots for the audio serial interface
  • Tri-state feature (with enable and disable) for the unused audio data slots of the device
  • Supports a bus-holder feature (with enable and disable) to keep the last driven value on the audio bus
  • The GPIOx pin can be configured as a secondary output data lane for the audio serial interface
  • The GPIOx or GPIx pin can be used in a daisy-chain configuration of multiple PCM6480-Q1 devices
  • Supports one BCLK cycle data latching timing to relax the timing requirement for the high-speed interface
  • Programmable master and slave options for the audio serial interface
  • Ability to synchronize the multiple devices for the simultaneous sampling requirement across devices
See the Multiple PCM6xx0-Q1 Devices With Shared TDM and I2C Bus application report for further details.