ZHCSSG0B December   2022  – April 2024 CC1314R10

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 功能方框图
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
    1. 6.1 Pin Diagram—RGZ Package (Top View)
    2. 6.2 Signal Descriptions—RGZ Package
    3. 6.3 Connections for Unused Pins and Modules—RGZ Package
    4. 6.4 Pin Diagram—RSK Package (Top View)
    5. 6.5 Signal Descriptions—RSK Package
    6. 6.6 Connection of Unused Pins and Module—RSK Package
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Power Supply and Modules
    5. 7.5  Power Consumption—Power Modes
    6. 7.6  Power Consumption—Radio Modes
    7. 7.7  Nonvolatile (Flash) Memory Characteristics
    8. 7.8  Thermal Resistance Characteristics
    9. 7.9  RF Frequency Bands
    10. 7.10 861MHz to 1054MHz—Receive (RX)
    11. 7.11 861MHz to 1054MHz—Transmit (TX) 
    12. 7.12 861MHz to 1054MHz - PLL Phase Noise Wideband Mode
    13. 7.13 861MHz to 1054MHz - PLL Phase Noise Narrowband Mode
    14. 7.14 Timing and Switching Characteristics
      1. 7.14.1 Reset Timing
      2. 7.14.2 Wakeup Timing
      3. 7.14.3 Clock Specifications
        1. 7.14.3.1 48MHz Clock Input (TCXO)
        2. 7.14.3.2 48MHz Crystal Oscillator (XOSC_HF)
        3. 7.14.3.3 48MHz RC Oscillator (RCOSC_HF)
        4. 7.14.3.4 2MHz RC Oscillator (RCOSC_MF)
        5. 7.14.3.5 32.768 kHz Crystal Oscillator (XOSC_LF)
        6. 7.14.3.6 32 kHz RC Oscillator (RCOSC_LF)
      4. 7.14.4 Serial Peripheral Interface (SPI) Characteristics
        1. 7.14.4.1 SPI Characteristics
        2. 7.14.4.2 SPI Master Mode
        3. 7.14.4.3 SPI Master Mode Timing Diagrams
        4. 7.14.4.4 SPI Slave Mode
        5. 7.14.4.5 SPI Slave Mode Timing Diagrams
      5. 7.14.5 UART
        1. 7.14.5.1 UART Characteristics
    15. 7.15 Peripheral Characteristics
      1. 7.15.1 ADC
        1. 7.15.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 7.15.2 DAC
        1. 7.15.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 7.15.3 Temperature and Battery Monitor
        1. 7.15.3.1 Temperature Sensor
        2. 7.15.3.2 Battery Monitor
      4. 7.15.4 Comparators
        1. 7.15.4.1 Low-Power Clocked Comparator
        2. 7.15.4.2 Continuous Time Comparator
      5. 7.15.5 Current Source
        1. 7.15.5.1 Programmable Current Source
      6. 7.15.6 GPIO
        1. 7.15.6.1 GPIO DC Characteristics
    16. 7.16 Typical Characteristics
      1. 7.16.1 MCU Current
      2. 7.16.2 RX Current
      3. 7.16.3 TX Current
      4. 7.16.4 RX Performance
      5. 7.16.5 TX Performance
      6. 7.16.6 ADC Performance
  9. 8 Detailed Description
    1. 8.1  Overview
    2. 8.2  System CPU
    3. 8.3  Radio (RF Core)
      1. 8.3.1 Proprietary Radio Formats
    4. 8.4  Memory
    5. 8.5  Sensor Controller
    6. 8.6  Cryptography
    7. 8.7  Timers
    8. 8.8  Serial Peripherals and I/O
    9. 8.9  Battery and Temperature Monitor
    10. 8.10 µDMA
    11. 8.11 Debug
    12. 8.12 Power Management
    13. 8.13 Clock Systems
    14. 8.14 Network Processor
  10. 9 Application, Implementation, and Layout
    1. 9.1 Reference Designs
    2. 9.2 Junction Temperature Calculation
  11. 10Device and Documentation Support
    1. 10.1 Tools and Software
      1. 10.1.1 SimpleLink™ Microcontroller Platform
    2. 10.2 Documentation Support
    3. 10.3 支持资源
    4. 10.4 Trademarks
    5. 10.5 静电放电警告
    6. 10.6 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Packaging Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.10 861MHz to 1054MHz—Receive (RX)

When Measured on the LP-EM-CC1314R10 reference design with Tc = 25°C, VDDS = 3.0V with
DC/DC enabled unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX path.  All measurements are performed conducted.
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
General Parameters
Digital channel filter programmable receive bandwidth44000kHz
Data rate step size1.5bps
Spurious emissions 25MHz to 1GHz868MHz
Conducted emissions measured according to ETSI EN 300 220		< –57dBm
Spurious emissions 1GHz to 13GHz< –47dBm
Wi-SUN, 50kbps, ±12.5kHz deviation, 2-GFSK, 78 kHz RX BW, #1a
SensitivityMRFSK, 866.6MHz, 10% PER, 250 byte payload–106dBm
Saturation limit10% PER, 250 byte payload, 866.6MHz10dBm
Selectivity, +100kHz10% PER, 250 byte payload, 866.6MHz. Wanted signal 3dB above sensitivity level.33dB
Selectivity, -100kHz31dB
Selectivity, +200kHz38dB
Selectivity, -200kHz37dB
RSSI dynamic rangeStarting from the sensitivity limit 93dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Wi-SUN, 50kbps, ±25kHz deviation, 2-GFSK, 100kHz RX BW, #1b
SensitivityMRFSK, 918.2MHz, 10% PER, 250 byte payload–106dBm
Saturation limit10% PER, 250 byte payload, 918.2MHz10dBm
Selectivity, +200kHz10% PER, 250 byte payload, 918.2MHz. Wanted signal 3dB above sensitivity level.37dB
Selectivity, -200kHz35dB
Selectivity, +400kHz42dB
Selectivity, -400kHz41dB
RSSI dynamic rangeStarting from the sensitivity limit 95dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Wi-SUN, 100kbps, ±25kHz deviation, 2-GFSK, 135kHz RX BW, #2a
SensitivityMRFSK, 866.6MHz, 10% PER, 250 byte payload–103dBm
Saturation limit10% PER, 250 byte payload, 866.6MHz10dBm
Selectivity, +200kHz10% PER, 250 byte payload, 866.6MHz. Wanted signal 3dB above sensitivity level.40dB
Selectivity, -200kHz38dB
Selectivity, +400kHz46dB
Selectivity, -400kHz44dB
RSSI dynamic rangeStarting from the sensitivity limit 95dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Wi-SUN, 100kbps, ±50kHz deviation, 2-GFSK, 208 kHz RX BW, #2b
SensitivityMRFSK, 920.9MHz, 10% PER, 250 byte payload–102dBm
Saturation limit10% PER, 250 byte payload, 920.9MHz10dBm
Selectivity, +400kHz10% PER, 250 byte payload, 920.9MHz. Wanted signal 3dB above sensitivity level, modulated blocker.42dB
Selectivity, -400kHz39dB
Selectivity, +800kHz52dB
Selectivity, -800kHz46dB
RSSI dynamic rangeStarting from the sensitivity limit 91dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Wi-SUN, 150kbps, ±37.5kHz deviation, 2-GFSK, 273 kHz RX BW, #3
SensitivityMRFSK, 918.4MHz, 10% PER, 250 byte payload–99dBm
Saturation limit10% PER, 250 byte payload, 918.4MHz10dBm
Selectivity, +400kHz10% PER, 250 byte payload, 918.4MHz. Wanted signal 3dB above sensitivity level.41dB
Selectivity, -400kHz39dB
Selectivity, +800kHz50dB
Selectivity, -800kHz46dB
RSSI dynamic rangeStarting from the sensitivity limit 86dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Wi-SUN, 200kbps, ±50kHz deviation, 2-GFSK, 335kHz RX BW, #4a
SensitivityMRFSK, 918.4MHz, 10% PER, 250 byte payload–99dBm
Saturation limit10% PER, 250 byte payload, 918.4MHz10dBm
Selectivity, +400kHz10% PER, 250 byte payload, 918.4MHz. Wanted signal 3dB above sensitivity level.42dB
Selectivity, -400kHz40dB
Selectivity, +800kHz51dB
Selectivity, -800kHz47dB
RSSI dynamic rangeStarting from the sensitivity limit 91dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Wi-SUN, 200kbps, ±100kHz deviation, 2-GFSK, 416kHz RX BW, #4b
SensitivityMRFSK, 920.8MHz, 10% PER, 250 byte payload–98dBm
Saturation limit10% PER, 250 byte payload, 920.8MHz10dBm
Selectivity, +600kHz10% PER, 250 byte payload, 920.8MHz. Wanted signal 3dB above sensitivity level, modulated blocker.46dB
Selectivity, -600kHz43dB
Selectivity, +1200kHz54dB
Selectivity, -1200kHz51dB
RSSI dynamic rangeStarting from the sensitivity limit 86dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Wi-SUN, 300kbps, ±75kHz deviation, 2-GFSK, 496kHz RX BW, #5
SensitivityMRFSK, 917.6MHz, 10% PER, 250 byte payload–97dBm
Saturation limit10% PER, 250 byte payload, 917.6MHz10dBm
Selectivity, +600kHz10% PER, 250 byte payload, 917.6MHz. Wanted signal 3dB above sensitivity level.42dB
Selectivity, -600kHz37dB
Selectivity, +1200kHz51dB
Selectivity, -1200kHz40dB
RSSI dynamic rangeStarting from the sensitivity limit 86dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
802.15.4-2020, 10kbps, ±5kHz deviation, 2-FSK, 26kHz RX BW, Mode #1a
SensitivityFSK, 915.0MHz, 20 byte PSDU < 10% PER–113dBm
SensitivityFSK, 868.3MHz, 20 byte PSDU < 10% PER–113dBm
Saturation limitPSDU length 20 octets; PER < 10%, 868.3MHz10dBm
Selectivity, +50kHzPSDU length 20 octets; PER < 10%, 868.3MHz36dB
Selectivity, -50kHz36dB
Selectivity, +100kHz40dB
Selectivity, -100kHz39dB
Selectivity, +200kHz44dB
Selectivity, -200kHz37dB
Blocking, +1MHz60dB
Blocking, -1MHz59dB
Blocking, +2MHz64dB
Blocking, -2MHz64dB
Blocking, +5MHz75dB
Blocking, -5MHz74dB
Blocking, +10MHz79dB
Blocking, -10MHz79dB
Blocking + 5% Fc. (45.75MHz)10% PER, 20 byte payload, 866.6MHz 802.15.4g mandatory mode, wanted signal -94dBm. 3dB above usable sensitivity limit according to ETSI EN 300 220 V3.1.1 (usable sensitivity -97dBm). Limit is Cat 1.5 requirement.–15dBm
Blocking - 5% Fc. (-45.75MHz)–15dBm
Image rejection (image compensation enabled)20 byte PSDU < 10% PER, 866.6MHz. Wanted signal 3dB above sensitivity limit.39dB
Image rejection (image compensation enabled)20 byte PSDU < 10% PER, 866.6MHz(1)39dB
RSSI dynamic rangeStarting from the sensitivity limit 100dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Frequency error tolerance (ppm)10% PER, 20 byte payload, measured at 10dB above sensitivity level. Negative offset–12ppm
Frequency error tolerance (ppm)10% PER, 20 byte payload, measured at 10dB above sensitivity level. Positive offset12ppm
Symbol rate error tolerance (ppm)10% PER, 20 byte payload, measured at 10dB above sensitivity level.
Negative offset		–1000ppm
Symbol rate error tolerance (ppm)10% PER, 20 byte payload, measured at 10dB above sensitivity level.
Positive offset		1000ppm
802.15.4-2020, 20kbps, ±10kHz deviation, 2-FSK, 52 kHz RX BW, Mode #1b
SensitivityFSK, 20kbps, ±10kHz deviation, 2-GFSK, 915.0MHz, 52 kHz RX BW, 20 byte PSDU < 10% PER–110dBm
SensitivityFSK, 20kbps, ±10kHz deviation, 2-GFSK, 868.3MHz, 52 kHz RX BW, 20 byte PSDU < 10% PER–110dBm
Saturation limit20 byte PSDU < 10% PER, 868.3MHz10dBm
Selectivity, +100kHz20-byte PSDU < 10% PER, 868.3MHz38dB
Selectivity, -100kHz36dB
Selectivity, +200kHz44dB
Selectivity, -200kHz42dB
Selectivity, +400kHz49dB
Selectivity, -400kHz44dB
Blocking, +1MHz58dB
Blocking, -1MHz54dB
Blocking, -2MHz61dB
Blocking, +2MHz61dB
Blocking, -5MHz70dB
Blocking, +5MHz70dB
Blocking, -10MHz75dB
Blocking, +10MHz76dB
Blocking + 5% Fc. (45.75MHz)20 byte PSDU < 10% PER, 866.6MHz,  wanted signal -94dBm. 3dB above usable sensitivity limit according to ETSI EN 300 220 V3.1.1 (usable sensitivity -97dBm). Limit is Cat 1.5 requirement.–13dBm
Blocking - 5% Fc. (-45.75MHz)–13dBm
Image rejection (image compensation enabled)20 byte PSDU < 10% PER, 866.6MHz. Wanted signal 3dB above sensitivity limit.39dB
Image rejection (image compensation enabled)20 byte PSDU < 10% PER, 866.6MHz(1)39dB
RSSI dynamic rangeStarting from the sensitivity limit 100dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Frequency error tolerance (ppm)10% PER, 20 byte payload, measured at 10dB above sensitivity level.
Negative offset		24ppm
Frequency error tolerance (ppm)10% PER, 20 byte payload, measured at 10dB above sensitivity level.
Positive offset		24ppm
Symbol rate error tolerance (ppm)10% PER, 20 byte payload, measured at 10dB above sensitivity level.
Negative offset		–1000ppm
Symbol rate error tolerance (ppm)10% PER, 20 byte payload, measured at 10dB above sensitivity level.
Positive offset		1000ppm
802.15.4, 200kbps, ±50kHz deviation, 2-GFSK, 311kHz RX BW
Sensitivity1% BER, 868MHz–103dBm
Sensitivity1% BER, 915MHz–103dBm
Selectivity, +400kHz1% BER, 915MHz. Wanted signal 3dB above sensitivity limit.45dB
Selectivity, -400kHz1% BER, 915MHz. Wanted signal 3dB above sensitivity limit.45dB
Selectivity, +800kHz1% BER, 915MHz. Wanted signal 3dB above sensitivity limit.52dB
Selectivity, –800kHz1% BER, 915MHz. Wanted signal 3dB above sensitivity limit.47dB
Blocking, +2MHz1% BER, 915MHz. Wanted signal 3dB above sensitivity limit.59dB
Blocking, –2MHz1% BER, 915MHz. Wanted signal 3dB above sensitivity limit.56dB
Blocking, +10MHz1% BER, 915MHz. Wanted signal 3dB above sensitivity limit.71dB
Blocking, –10MHz1% BER, 915MHz. Wanted signal 3dB above sensitivity limit.70dB
802.15.4, 500kbps, ±190kHz deviation, 2-GFSK, 622 kHz RX BW
Sensitivity 500kbps915MHz, 1% PER, 127 byte payload–95dBm
Selectivity, ±1MHz915MHz, 1% PER, 127 byte payload. Wanted signal at -88dBm34dB
Selectivity, ±2MHz915MHz, 1% PER, 127 byte payload. Wanted signal at -88dBm46dB
Co-channel rejection915MHz, 1% PER, 127 byte payload. Wanted signal at -71dBm–8dB
SimpleLink™ Long Range  2.5/5kbps (20ksps), ±5kHz Deviation, 2-GFSK, 34kHz RX Bandwidth, FEC = 1:2, DSSS = 1:4/1:2
Sensitivity2.5kbps, 1% BER, 868MHz–121dBm
Sensitivity2.5kbps, 1% BER, 915MHz–121dBm
Sensitivity5kbps, 1% BER, 868MHz–119dBm
Sensitivity5kbps, 1% BER, 915MHz–119dBm
Saturation limit2.5kbps, 1% BER, 868MHz10dBm
Selectivity, +100kHz2.5kbps, 1% BER, 868MHz(1)49dB
Selectivity, -100kHz2.5kbps, 1% BER, 868MHz(1)49dB
Selectivity, +200kHz2.5kbps, 1% BER, 868MHz(1)52dB
Selectivity, -200kHz2.5kbps, 1% BER, 868MHz(1)48dB
Selectivity, +300kHz2.5kbps, 1% BER, 868MHz(1)54dB
Selectivity, -300kHz2.5kbps, 1% BER, 868MHz(1)48dB
Blocking, +1MHz2.5kbps, 1% BER, 868MHz(1)65dB
Blocking, -1MHz2.5kbps, 1% BER, 868MHz(1)60dB
Blocking, +2MHz2.5kbps, 1% BER, 868MHz(1)70dB
Blocking, -2MHz2.5kbps, 1% BER, 868MHz(1)68dB
Blocking, +5MHz2.5kbps, 1% BER, 868MHz(1)78dB
Blocking, -5MHz2.5kbps, 1% BER, 868MHz(1)77dB
Blocking, +10MHz2.5kbps, 1% BER, 868MHz(1)87dB
Blocking, -10MHz2.5kbps, 1% BER, 868MHz(1)92dB
Image rejection (image compensation enabled)2.5kbps, 1% BER, 868MHz(1)47dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Frequency error tolerance (ppm)2.5kbps, measured at –110dBm. –24/26ppm
Symbolrate error tolerance (ppm)2.5kbps, measured at –110dBm.–90/70ppm
Narrowband, 9.6kbps ±2.4kHz Deviation, 2-GFSK, 868MHz, 17.1kHz RX BW
Sensitivity1% BER-117dBm
Adjacent Channel Rejection1% BER. Wanted signal 3dB above usable sensitivity limit (usable sensitivity –104.6dBm). Interferer ±20kHz42dB
Alternate Channel Rejection1% BER. Wanted signal 3dB above usable sensitivity limit (usable sensitivity –104.6dBm). Interferer ±40kHz42dB
Blocking, ±1MHz1% BER. Wanted signal 3dB above usable sensitivity limit (usable sensitivity –104.6dBm)66dB
Blocking, ±2MHz1% BER. Wanted signal 3dB above usable sensitivity limit (usable sensitivity –104.6dBm)71dB
Blocking, ±10MHz1% BER. Wanted signal 3dB above usable sensitivity limit (usable sensitivity –104.6dBm)85dB
802.15.4, 50kbps, ±25kHz Deviation, 2-GFSK, 100kHz RX BW (Legacy)
Sensitivity1% BER, 868MHz–110dBm
Sensitivity1% BER, 915MHz–110dBm
Saturation limit1% BER, 868MHz10dBm
Selectivity, +200kHz1% BER, 868MHz(1)44dB
Selectivity, -200kHz44dB
Selectivity, +400kHz54dB
Selectivity, -400kHz44dB
Blocking, +1MHz57dB
Blocking, -1MHz57dB
Blocking, +2MHz61dB
Blocking, -2MHz61dB
Blocking, +5MHz67dB
Blocking, -5MHz67dB
Blocking, +10MHz76dB
Blocking, -10MHz76dB
Blocking + 5% Fc. (43.42MHz) 1% BER, 868MHz
802.15.4g mandatory mode, wanted signal –94dBm. 3dB above usable sensitivity limit according to ETSI EN 300 220 V3.1.1 (usable sensitivity -97dBm). Limit is Cat 1.5 requirement.		–15dBm
Blocking - 5% Fc. (-43.42MHz) –15dBm
Image rejection (image compensation enabled)1% BER, 868MHz. Wanted signal 3dB above sensitivity limit39dB
RSSI dynamic rangeStarting from the sensitivity limit 95dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Frequency error tolerance (ppm)1% BER, measured at –100dBm (10dB above sensitivity level). Negative offset–30ppm
Frequency error tolerance (ppm)1% BER, measured at –100dBm (10dB above sensitivity level). Positive offset25ppm
Symbol rate error tolerance (ppm)1% BER, measured at –100dBm (10dB above sensitivity level).
Negative offset		–2000ppm
Symbol rate error tolerance (ppm) 1% BER, measured at –100dBm (10dB above sensitivity level)
Positive offset		2000ppm
802.15.4, 100kbps, ±25kHz Deviation, 2-GFSK, 137kHz RX BW
Sensitivity 100kbps868MHz, 1% PER, 127 byte payload–103dBm
Selectivity, ±200kHz868MHz, 1% PER, 127 byte payload. Wanted signal at –96dBm38dB
Selectivity, ±400kHz44dB
Co-channel rejection868MHz, 1% PER, 127 byte payload. Wanted signal at –79dBm–9dB
Generic OOK (16.384kbps, OOK w / Manchester encoding, 100kHz RX BW)
SensitivityOOK, 915.0MHz, 1% BER–114dBm
SensitivityOOK, 868.8MHz, 1% BER–113dBm
Saturation limit868.3MHz0dBm
Selectivity, +200kHz868.3MHz. Wanted signal 3dB above sensitivity level.52dB
Selectivity, –200kHz47dB
Selectivity, +400kHz42dB
Selectivity, –400kHz42dB
Blocking, +1MHz68dB
Blocking, –1MHz64dB
Blocking, +2MHz68dB
Blocking, –2MHz64dB
Blocking, +5MHz74dB
Blocking, –5MHz73dB
Blocking, +10MHz68dB
Blocking, –10MHz64dB
RSSI dynamic rangeStarting from the sensitivity limit 95dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
Frequency error tolerance (ppm)Measured at  10dB above sensitivity level. Negative offset-40ppm
Frequency error tolerance (ppm)Measured at 10dB above sensitivity level. Positive offset40ppm
Symbol rate error tolerance (ppm)Measured at 10dB above sensitivity level.
Negative offset		-2000ppm
Symbol rate error tolerance (ppm) Measured at 10dB above sensitivity level
Positive offset		2000ppm
WB-DSSS, 240/120/60/30kbps (480ksym/s, 2-GFSK, ±195kHz Deviation, FEC (Half Rate), DSSS = 1/2/4/8, 622 kHz RX BW)
Sensitivity240kbps, DSSS = 1, 1% BER, 915.0MHz–105dBm
Sensitivity120kbps, DSSS = 2, 1% BER, 915.0MHz–106dBm
Sensitivity60kbps, DSSS = 4, 1% BER, 915.0MHz–108dBm
Sensitivity30kbps, DSSS = 8, 1% BER, 915.0MHz–109dBm
Saturation limit915.0MHz0dBm
Blocking +1MHz240kbps, DSSS = 154dB
120kbps, DSSS = 257dB
60kbps, DSSS = 457dB
30kbps, DSSS = 857dB
Blocking -1MHz240kbps, DSSS = 149dB
120kbps, DSSS = 250dB
60kbps, DSSS = 452dB
30kbps, DSSS = 853dB
Blocking +2MHz240kbps, DSSS = 154dB
120kbps, DSSS = 255dB
60kbps, DSSS = 457dB
30kbps, DSSS = 858dB
Blocking -2MHz240kbps, DSSS = 153dB
120kbps, DSSS = 254dB
60kbps, DSSS = 456dB
30kbps, DSSS = 856dB
Blocking +5MHz240kbps, DSSS = 155dB
120kbps, DSSS = 256dB
60kbps, DSSS = 458dB
30kbps, DSSS = 859dB
Blocking -5MHz240kbps, DSSS = 154dB
120kbps, DSSS = 255dB
60kbps, DSSS = 457dB
30kbps, DSSS = 858dB
Blocking +10MHz240kbps, DSSS = 169dB
120kbps, DSSS = 270dB
60kbps, DSSS = 472dB
30kbps, DSSS = 873dB
Blocking -10MHz240kbps, DSSS = 165dB
120kbps, DSSS = 267dB
60kbps, DSSS = 469dB
30kbps, DSSS = 870dB
RSSI dynamic rangeStarting from the sensitivity limit 85dB
RSSI accuracyStarting from the sensitivity limit across the given dynamic range±3dB
(1) Wanted signal 3dB above usable sensitivity limit according to ETSI EN 300 220 v. 3.1.1