ZHCSRJ6C June   2010  – January 2023 TLV320AIC3104-Q1

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 说明（续）
  6. 6 Device Comparison
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Thermal Information
    5. 8.5  Electrical Characteristics
    6. 8.6  Switching Characteristics I2S/LJF/RJF Timing in Master Mode
    7. 8.7  Switching Characteristics I2S/LJF/RJF Timing in Slave Mode
    8. 8.8  Switching Characteristics DSP Timing in Master Mode
    9. 8.9  Switching Characteristics DSP Timing in Slave Mode
    10. 8.10 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Audio Data Converters
      2. 9.3.2  Stereo Audio ADC
        1. 9.3.2.1 Stereo Audio ADC High-Pass Filter
      3. 9.3.3  Automatic Gain Control (AGC)
      4. 9.3.4  Stereo Audio DAC
      5. 9.3.5  Digital Audio Processing for Playback
      6. 9.3.6  Digital Interpolation Filter
      7. 9.3.7  Delta-Sigma Audio DAC
      8. 9.3.8  Audio DAC Digital Volume Control
      9. 9.3.9  Analog Output Common-mode Adjustment
      10. 9.3.10 Audio DAC Power Control
      11. 9.3.11 Audio Analog Inputs
      12. 9.3.12 Analog Input Bypass Path Functionality
      13. 9.3.13 ADC PGA Signal Bypass Path Functionality
      14. 9.3.14 Input Impedance and VCM Control
      15. 9.3.15 MICBIAS Generation
      16. 9.3.16 Analog Fully Differential Line Output Drivers
      17. 9.3.17 Analog High-Power Output Drivers
      18. 9.3.18 Short-Circuit Output Protection
      19. 9.3.19 Jack and Headset Detection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Digital Audio Processing for Record Path
      2. 9.4.2 Increasing DAC Dynamic Range
      3. 9.4.3 Passive Analog Bypass During Power Down
      4. 9.4.4 Hardware Reset
    5. 9.5 Programming
      1. 9.5.1  Digital Control Serial Interface
      2. 9.5.2  I2C Control Interface
      3. 9.5.3  I2C Bus Debug in a Glitched System
      4. 9.5.4  Digital Audio Data Serial Interface
      5. 9.5.5  Right-Justified Mode
      6. 9.5.6  Left-Justified Mode
      7. 9.5.7  I2S Mode
      8. 9.5.8  DSP Mode
      9. 9.5.9  TDM Data Transfer
      10. 9.5.10 Audio Clock Generation
    6. 9.6 Register Maps
      1. 9.6.1 Output Stage Volume Controls
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 External Speaker Driver in Infotainment and Cluster Applications
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
        3. 10.2.1.3 Application Curves
      2. 10.2.2 External Speaker Amplifier With Separate Line Outputs
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Device Nomenclature
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Receiving Notification of Documentation Updates
    4. 13.4 Community Resources
    5. 13.5 Trademarks
    6. 13.6 静电放电警告
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

9.4.3 Passive Analog Bypass During Power Down

Programming the TLV320AIC3104-Q1 to passive analog bypass occurs by configuring the output stage switches for passthrough. This is done by opening switches SW-L0, SW-L3, SW-R0, and SW-R3 and closing SW-L1 and SW-R1. See Figure 9-12. Programming this mode is done by writing to page 0, register 108.

Connecting the MIC1LP/LINE1LP input signal to the LEFT_LOP pin is done by closing SW-L1 and opening SWL0; this action is done by writing a 1 to page 0, register 108, bit D0. Connecting the MIC1LM/LINE1LM input signal to the LEFT_LOM pin is done by closing SW-L4 and opening SW-L3; this action is done by writing a 1 to page 0, register 108, bit D1.

Connecting the MIC1RP/LINE1RP input signal to the RIGHT_LOP pin is done by closing SW-R1 and opening SW-R0; this action is done by writing a 1 to page 0, register 108, bit D4. Connecting MIC1RM/LINE1RM input signal to the RIGHT_LOM pin is done by closing SW-R4 and opening SW-R3; this action is done by writing a 1 to page 0, register 108, bit D5. A diagram of the passive analog bypass mode configuration is shown in Figure 9-12.

In general, connecting two switches to the same output pin should be avoided, as this error shorts two input signals together, and would likely cause distortion of the signal as the two signals are in contention. Poor frequency response would also likely occur.

Figure 9-12 Passive Analog Bypass Mode Configuration