ZHCSOF9B april   2022  – june 2023 TPS25981

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Switching Characteristics
      1.      16
    8. 7.8 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Undervoltage Lockout (UVLO and UVP)
      2. 8.3.2 Overvoltage Lockout (OVLO)
      3. 8.3.3 Inrush Current, Overcurrent, and Short-Circuit Protection
        1. 8.3.3.1 Slew Rate (dVdt) and Inrush Current Control
        2. 8.3.3.2 Circuit-Breaker During Steady-State
        3. 8.3.3.3 Active Current Limiting During Start-Up
        4. 8.3.3.4 Short-Circuit Protection
      4. 8.3.4 Analog Load Current Monitor
      5. 8.3.5 Overtemperature Protection (OTP)
      6. 8.3.6 Fault Response and Indication (FLT)
      7. 8.3.7 Power Good Indication (PG)
      8. 8.3.8 Quick Output Discharge (QOD)
      9. 8.3.9 Reverse Current Blocking FET Driver
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Single Device, Self-Controlled
      2. 9.1.2 Parallel Operation
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Device Selection
        2. 9.2.2.2 Setting Output Voltage Rise Time (tR)
        3. 9.2.2.3 Setting Overcurrent Threshold (ILIM)
        4. 9.2.2.4 Setting Overcurrent Blanking Interval (tITIMER)
        5. 9.2.2.5 Voltage Drop
      3. 9.2.3 Application Curves
  11. 10Power Supply Recommendations
    1. 10.1 Transient Protection
    2. 10.2 Output Short-Circuit Measurements
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 接收文档更新通知
    3. 12.3 支持资源
    4. 12.4 Trademarks
    5. 12.5 静电放电警告
    6. 12.6 术语表
  14. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
Parameter Pin MIN MAX UNIT
VIN Input voltage range IN 2.7 16 V
VOUT Output voltage range OUT VIN V
VEN/UVLO EN/UVLO pin voltage range EN/UVLO 5(1) V
VOV EN/OVLO pin voltage range EN/OVLO 0.5 1.5 V
VdVdT dVdT pin capacitor voltage rating dVdt VIN + 5 V V
VFLTB FLT pin voltage range FLT 5 V
VPG PG pin voltage range PG 5 V
VITIMER ITIMER pin capacitor voltage rating ITIMER 4 V
RILM ILM pin resistance to GND ILM 600 4400 Ω
IMAX Continuous switch current, TJ ≤ 125℃ IN to OUT 10 A
TJ Junction temperature –40 125 °C
(1) For supply voltages below 5V, it is okay to pull up the EN pin to IN directly. For supply voltages greater than 5V , it is recommended to use a resistor divider with minimum pull-up resistor value of 350 kΩ.