ZHCSMU9A December   2020  – September 2021 TAS2764

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Timing Requirements
    7. 6.7 TDM Port Timing Requirements
    8. 6.8 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1  Overview
    2. 8.2  Functional Block Diagram
    3. 8.3  Feature Description
      1. 8.3.1 Device Address Selection
      2. 8.3.2 General I2C Operation
      3. 8.3.3 Register Organization
    4. 8.4  Device Functional Modes
      1. 8.4.1  TDM Port
      2. 8.4.2  Playback Signal Path
        1. 8.4.2.1  High Pass Filter
        2. 8.4.2.2  Amplifier Inversion
        3. 8.4.2.3  Digital Volume Control and Amplifier Output Level
          1. 8.4.2.3.1 Safe Mode
        4. 8.4.2.4  VBAT1S Supply
        5. 8.4.2.5  Low Voltage Signaling (LVS)
        6. 8.4.2.6  Y-Bridge
        7. 8.4.2.7  Noise Gate
        8. 8.4.2.8  Supply Tracking Limiter with Brown Out Prevention
          1. 8.4.2.8.1 Supply Tracking Limiter
          2. 8.4.2.8.2 Brownout Prevention (BOP)
        9. 8.4.2.9  Inter Chip Gain Alignment
          1. 8.4.2.9.1 Inter-Chip Communication (ICC) Pin
        10. 8.4.2.10 Class-D Settings
          1. 8.4.2.10.1 Synchronization and EMI
      3. 8.4.3  SAR ADC
      4. 8.4.4  Current and Voltage (IV) Sense
      5. 8.4.5  Post Filter Feed-Back (PFFB)
      6. 8.4.6  Load Diagnostics
      7. 8.4.7  Thermal Foldback
      8. 8.4.8  Over Power Protection
      9. 8.4.9  Clocks and PLL
      10. 8.4.10 Echo Reference
    5. 8.5  Operational Modes
      1. 8.5.1 Hardware Shutdown
      2. 8.5.2 Mode Control and Software Reset
      3. 8.5.3 Software Shutdown
      4. 8.5.4 Mute
      5. 8.5.5 Active
      6. 8.5.6 Diagnostic
      7. 8.5.7 Noise Gate
    6. 8.6  Faults and Status
      1. 8.6.1 Faults and Status over TDM
    7. 8.7  Power Sequencing Requirements
    8. 8.8  Digital Input Pull Downs
    9. 8.9  Register Map
      1. 8.9.1   Register Summary Table Page=0x00
      2. 8.9.2   Register Summary Table Page=0x01
      3. 8.9.3   Register Summary Table Page=0x04
      4. 8.9.4   PAGE (page=0x00 address=0x00) [reset=00h]
      5. 8.9.5   SW_RESET (page=0x00 address=0x01) [reset=00h]
      6. 8.9.6   MODE_CTRL (page=0x00 address=0x02) [reset=1Ah]
      7. 8.9.7   CHNL_0 (page=0x00 address=0x03) [reset=28h]
      8. 8.9.8   DC_BLK0 (page=0x00 address=0x04) [reset=21h]
      9. 8.9.9   DC_BLK1 (page=0x00 address=0x05) [reset=41h]
      10. 8.9.10  MISC_CFG1 (page=0x00 address=0x06) [reset=00h]
      11. 8.9.11  MISC_CFG2 (page=0x00 address=0x07) [reset=20h]
      12. 8.9.12  TDM_CFG0 (page=0x00 address=0x08) [reset=09h]
      13. 8.9.13  TDM_CFG1 (page=0x00 address=0x09) [reset=02h]
      14. 8.9.14  TDM_CFG2 (page=0x00 address=0x0A) [reset=0Ah]
      15. 8.9.15  LIM_MAX_ATTN (page=0x00 address=0x0B) [reset=80h]
      16. 8.9.16  TDM_CFG3 (page=0x00 address=0x0C) [reset=10h]
      17. 8.9.17  TDM_CFG4 (page=0x00 address=0x0D) [reset=13h]
      18. 8.9.18  TDM_CFG5 (page=0x00 address=0x0E) [reset=42h]
      19. 8.9.19  TDM_CFG6 (page=0x00 address=0x0F) [reset=40h]
      20. 8.9.20  TDM_CFG7 (page=0x00 address=0x10) [reset=04h]
      21. 8.9.21  TDM_CFG8 (page=0x00 address=0x11) [reset=05h]
      22. 8.9.22  TDM_CFG9 (page=0x00 address=0x12) [reset=06h]
      23. 8.9.23  TDM_CFG10 (page=0x00 address=0x13) [reset=08h]
      24. 8.9.24  TDM_CFG11 (page=0x00 address=0x14) [reset=0Ah]
      25. 8.9.25  ICC_CNFG2 (page=0x00 address=0x15) [reset=00h]
      26. 8.9.26  TDM_CFG12 (page=0x00 address=0x16) [reset=12h]
      27. 8.9.27  ICLA_CFG0 (page=0x00 address=0x17) [reset=0Ch]
      28. 8.9.28  ICLA_CFG1 (page=0x00 address=0x18) [reset=00h]
      29. 8.9.29  DG_0 (page=0x00 address=0x19) [reset=0Dh]
      30. 8.9.30  DVC (page=0x00 address=0x1A) [reset=00h]
      31. 8.9.31  LIM_CFG0 (page=0x00 address=0x1B) [reset=22h]
      32. 8.9.32  LIM_CFG1 (page=0x00 address=0x1C) [reset=32h]
      33. 8.9.33  BOP_CFG0 (page=0x00 address=0x1D) [reset=40h]
      34. 8.9.34  BOP_CFG1 (page=0x00 address=0x1E) [reset=32h]
      35. 8.9.35  BOP_CFG2 (page=0x00 address=0x1F) [reset=02h]
      36. 8.9.36  BOP_CFG3 (page=0x00 address=0x20) [reset=06h]
      37. 8.9.37  BOP_CFG4 (page=0x00 address=0x21) [reset=2Ch]
      38. 8.9.38  BOP_CFG5 (page=0x00 address=0x22) [reset=4Ch]
      39. 8.9.39  BOP_CFG6 (page=0x00 address=0x23) [reset=20h]
      40. 8.9.40  BOP_CFG7 (page=0x00 address=0x24) [reset=02h]
      41. 8.9.41  BOP_CFG8 (page=0x00 address=0x25) [reset=06h]
      42. 8.9.42  BOP_CFG9 (page=0x00 address=0x26) [reset=32h]
      43. 8.9.43  BOP_CFG10 (page=0x00 address=0x27) [reset=46h]
      44. 8.9.44  BOP_CFG11 (page=0x00 address=0x28) [reset=20h]
      45. 8.9.45  BOP_CFG12 (page=0x00 address=0x29) [reset=02h]
      46. 8.9.46  BOP_CFG13 (page=0x00 address=0x2A) [reset=06h]
      47. 8.9.47  BOP_CFG14 (page=0x00 address=0x2B) [reset=38h]
      48. 8.9.48  BOP_CFG15 (page=0x00 address=0x2C) [reset=40h]
      49. 8.9.49  BOP_CFG17 (page=0x00 address=0x2D) [reset=20h]
      50. 8.9.50  BOP_CFG18 (page=0x00 address=0x2E) [reset=02h]
      51. 8.9.51  BOP_CFG19 (page=0x00 address=0x2F) [reset=06h]
      52. 8.9.52  BOP_CFG20 (page=0x00 address=0x30) [reset=3Eh]
      53. 8.9.53  BOP_CFG21 (page=0x00 address=0x31) [reset=37h]
      54. 8.9.54  BOP_CFG22 (page=0x00 address=0x32) [reset=20h]
      55. 8.9.55  BOP_CFG23 (page=0x00 address=0x33) [reset=FFh]
      56. 8.9.56  BOP_CFG24 (page=0x00 address=0x34) [reset=E6h]
      57. 8.9.57  NG_CFG0 (page=0x00 address=0x35) [reset=BDh]
      58. 8.9.58  NG_CFG1 (page=0x00 address=0x36) [reset=ADh]
      59. 8.9.59  LVS_CFG0 (page=0x00 address=0x37) [reset=A8h]
      60. 8.9.60  DIN_PD (page=0x00 address=0x38) [reset=03h]
      61. 8.9.61  IO_DRV0 (page=0x00 address=0x39) [reset=FFh]
      62. 8.9.62  IO_DRV1 (page=0x00 address=0x3A) [reset=FFh]
      63. 8.9.63  INT_MASK0 (page=0x00 address=0x3B) [reset=FCh]
      64. 8.9.64  INT_MASK1 (page=0x00 address=0x3C) [reset=BEh]
      65. 8.9.65  INT_MASK4 (page=0x00 address=0x3D) [reset=DFh]
      66. 8.9.66  INT_MASK2 (page=0x00 address=0x40) [reset=F6h]
      67. 8.9.67  INT_MASK3 (page=0x00 address=0x41) [reset=00h]
      68. 8.9.68  INT_LIVE0 (page=0x00 address=0x42) [reset=00h]
      69. 8.9.69  INT_LIVE1 (page=0x00 address=0x43) [reset=00h]
      70. 8.9.70  INT_LIVE1_0 (page=0x00 address=0x44) [reset=00h]
      71. 8.9.71  INT_LIVE2 (page=0x00 address=0x47) [reset=00h]
      72. 8.9.72  INT_LIVE3 (page=0x00 address=0x48) [reset=00h]
      73. 8.9.73  INT_LTCH0 (page=0x00 address=0x49) [reset=00h]
      74. 8.9.74  INT_LTCH1 (page=0x00 address=0x4A) [reset=00h]
      75. 8.9.75  INT_LTCH1_0 (page=0x00 address=0x4B) [reset=00h]
      76. 8.9.76  INT_LTCH2 (page=0x00 address=0x4F) [reset=00h]
      77. 8.9.77  INT_LTCH3 (page=0x00 address=0x50) [reset=00h]
      78. 8.9.78  INT_LTCH4 (page=0x00 address=0x51) [reset=00h]
      79. 8.9.79  VBAT_MSB (page=0x00 address=0x52) [reset=00h]
      80. 8.9.80  VBAT_LSB (page=0x00 address=0x53) [reset=00h]
      81. 8.9.81  PVDD_MSB (page=0x00 address=0x54) [reset=00h]
      82. 8.9.82  PVDD_LSB (page=0x00 address=0x55) [reset=00h]
      83. 8.9.83  TEMP (page=0x00 address=0x56) [reset=00h]
      84. 8.9.84  INT_CLK_CFG (page=0x00 address=0x5C) [reset=19h]
      85. 8.9.85  MISC_CFG3 (page=0x00 address=0x5D) [reset=80h]
      86. 8.9.86  CLOCK_CFG (page=0x00 address=0x60) [reset=0Dh]
      87. 8.9.87  IDLE_IND (page=0x00 address=0x63) [reset=48]
      88. 8.9.88  MISC_CFG4 (page=0x00 address=0x65) [reset=08]
      89. 8.9.89  TG_CFG0 (page=0x00 address=0x67) [reset=00h]
      90. 8.9.90  CLK_CFG (page=0x00 address=0x68) [reset=7Fh]
      91. 8.9.91  LV_EN_CFG (page=0x00 address=0x6A) [reset=12h]
      92. 8.9.92  NG_CFG2 (page=0x00 address=0x6B) [reset=01h]
      93. 8.9.93  NG_CFG3 (page=0x00 address=0x6C) [reset=00h]
      94. 8.9.94  NG_CFG4 (page=0x00 address=0x6D) [reset=00h]
      95. 8.9.95  NG_CFG5 (page=0x00 address=0x6E) [reset=1Ah]
      96. 8.9.96  NG_CFG6 (page=0x00 address=0x6F) [reset=00h]
      97. 8.9.97  NG_CFG7 (page=0x00 address=0x70) [reset=96h]
      98. 8.9.98  PVDD_UVLO (page=0x00 address=0x71) [reset=00h]
      99. 8.9.99  DAC_MOD_RST (page=0x00 address=0x76) [reset=02h]
      100. 8.9.100 REV_ID (page=0x00 address=0x7D) [reset=30h]
      101. 8.9.101 I2C_CKSUM (page=0x00 address=0x7E) [reset=00h]
      102. 8.9.102 BOOK (page=0x00 address=0x7F) [reset=00h]
      103. 8.9.103 LSR (page=0x01 address=0x19) [reset=40h]
      104. 8.9.104 SDOUT_HIZ_1 (page=0x01 address=0x3D) [reset=00h]
      105. 8.9.105 SDOUT_HIZ_2 (page=0x01 address=0x3E) [reset=00h]
      106. 8.9.106 SDOUT_HIZ_3 (page=0x01 address=0x3F) [reset=00h]
      107. 8.9.107 SDOUT_HIZ_4 (page=0x01 address=0x40) [reset=00h]
      108. 8.9.108 SDOUT_HIZ_5 (page=0x01 address=0x41) [reset=00h]
      109. 8.9.109 SDOUT_HIZ_6 (page=0x01 address=0x42) [reset=00h]
      110. 8.9.110 SDOUT_HIZ_7 (page=0x01 address=0x43) [reset=00h]
      111. 8.9.111 SDOUT_HIZ_8 (page=0x01 address=0x44) [reset=00h]
      112. 8.9.112 SDOUT_HIZ_9 (page=0x01 address=0x45) [reset=00h]
      113. 8.9.113 TG_EN (page=0x01 address=0x47) [reset=ABh]
      114. 8.9.114 DG_DC_VAL1 (page=0x04 address=0x08) [reset=40h]
      115. 8.9.115 DG_DC_VAL2 (page=0x04 address=0x09) [reset=26h]
      116. 8.9.116 DG_DC_VAL3 (page=0x04 address=0x0A) [reset=40h]
      117. 8.9.117 DC_DG_VAL4 (page=0x04 address=0x0B) [reset=00h]
      118. 8.9.118 LIM_TH_MAX1 (page=0x04 address=0x0C) [reset=68h]
      119. 8.9.119 LIM_TH_MAX2 (page=0x04 address=0x0D) [reset=00h]
      120. 8.9.120 LIM_TH_MAX3 (page=0x04 address=0x0E) [reset=00h]
      121. 8.9.121 LIM_TH_MAX4 (page=0x04 address=0x0F) [reset=00h]
      122. 8.9.122 LIM_TH_MIN1 (page=0x04 address=0x10) [reset=28h]
      123. 8.9.123 LIM_TH_MIN2 (page=0x04 address=0x11) [reset=00h]
      124. 8.9.124 LIM_TH_MIN3 (page=0x04 address=0x12) [reset=00h]
      125. 8.9.125 LIM_TH_MIN4 (page=0x04 address=0x13) [reset=00h]
      126. 8.9.126 LIM_INF_PT1 (page=0x04 address=0x14) [reset=56h]
      127. 8.9.127 LIM_INF_PT2 (page=0x04 address=0x15) [reset=66h]
      128. 8.9.128 LIM_INF_PT3 (page=0x04 address=0x16) [reset=66h]
      129. 8.9.129 LIM_INF_PT4 (page=0x04 address=0x17) [reset=00h]
      130. 8.9.130 LIM_SLOPE1 (page=0x04 address=0x18) [reset=10h]
      131. 8.9.131 LIM_SLOPE2 (page=0x04 address=0x19) [reset=00h]
      132. 8.9.132 LIM_SLOPE3 (page=0x04 address=0x1A) [reset=00h]
      133. 8.9.133 LIM_SLOPE4 (page=0x04 address=0x1B) [reset=00h]
      134. 8.9.134 TF_HLD1 (page=0x04 address=0x1C) [reset=00h]
      135. 8.9.135 TF_HLD2 (page=0x04 address=0x1D) [reset=03h]
      136. 8.9.136 TF_HLD3 (page=0x04 address=0x1E) [reset=E8h]
      137. 8.9.137 TF_HLD4 (page=0x04 address=0x1F) [reset=00h]
      138. 8.9.138 TF_RLS1 (page=0x04 address=0x20) [reset=40h]
      139. 8.9.139 TF_RLS2 (page=0x04 address=0x21) [reset=12h]
      140. 8.9.140 TF_RLS3 (page=0x04 address=0x22) [reset=E0h]
      141. 8.9.141 TF_RLS4 (page=0x04 address=0x23) [reset=00h]
      142. 8.9.142 TF_SLOPE1 (page=0x04 address=0x24) [reset=04h]
      143. 8.9.143 TF_SLOPE2 (page=0x04 address=0x25) [reset=08h]
      144. 8.9.144 TF_SLOPE3 (page=0x04 address=0x26) [reset=89h]
      145. 8.9.145 TF_SLOPE4 (page=0x04 address=0x27) [reset=00h]
      146. 8.9.146 TF_TEMP_TH1 (page=0x04 address=0x28) [reset=39h]
      147. 8.9.147 TF_TEMP_TH2 (page=0x04 address=0x29) [reset=80h]
      148. 8.9.148 TF_TEMP_TH3 (page=0x04 address=0x2A) [reset=00h]
      149. 8.9.149 TF_TEMP_TH4 (page=0x04 address=0x2B) [reset=00h]
      150. 8.9.150 TF_MAX_ATTN1 (page=0x04 address=0x2C) [reset=2Dh]
      151. 8.9.151 TF_MAX_ATTN2 (page=0x04 address=0x2D) [reset=6Ah]
      152. 8.9.152 TF_MAX_ATTN3 (page=0x04 address=0x2E) [reset=86h]
      153. 8.9.153 TF_MAX_ATTN4 (page=0x04 address=0x2F) [reset=00h]
      154. 8.9.154 LD_CFG0 (page=0x04 address=0x40) [reset=02h]
      155. 8.9.155 LD_CFG1 (page=0x04 address=0x41) [reset=ADh]
      156. 8.9.156 LD_CFG2 (page=0x04 address=0x42) [reset=B7h]
      157. 8.9.157 LD_CFG3 (page=0x04 address=0x43) [reset=00h]
      158. 8.9.158 LD_CFG4 (page=0x04 address=0x44) [reset=00h]
      159. 8.9.159 LD_CFG5 (page=0x04 address=0x45) [reset=1Bh]
      160. 8.9.160 LD_CFG6 (page=0x04 address=0x46) [reset=6Eh]
      161. 8.9.161 LD_CFG7 (page=0x04 address=0x47) [reset=00h]
      162. 8.9.162 CLD_EFF_1 (page=0x04 address=0x48) [reset=6Ch]
      163. 8.9.163 CLD_EFF_2 (page=0x04 address=0x49) [reset=CCh]
      164. 8.9.164 CLD_EFF_3 (page=0x04 address=0x4A) [reset=CDh]
      165. 8.9.165 CLD_EFF_4 (page=0x04 address=0x4B) [reset=00h]
      166. 8.9.166 LDG_RES1 (page=0x04 address=0x4C) [reset=00h]
      167. 8.9.167 LDG_RES2 (page=0x04 address=0x4D) [reset=00h]
      168. 8.9.168 LDG_RES3 (page=0x04 address=0x4E) [reset=00h]
      169. 8.9.169 LDG_RES4 (page=0x04 address=0x4F) [reset=00h]
    10. 8.10 SDOUT Equations
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
    3. 9.3 Design Requirements
    4. 9.4 Detailed Design Procedure
      1. 9.4.1 Mono/Stereo Configuration
      2. 9.4.2 EMI Passive Devices
    5. 9.5 Application Curves
  10. 10Initialization Set Up
    1. 10.1 Recommended Configuration at Power Up
    2. 10.2 Initial Device Configuration - 4 Channel Power Up (Default Mode - PWR_MODE1)
    3. 10.3 Initial Device Configuration - 44.1 kHz
    4. 10.4 Sample Rate Change - 48 kHz to 44.1kHz
    5. 10.5 Idle Channel Hysterisis
    6. 10.6 DSP Loopback
  11. 11Power Supply and I2C Recommendations
    1. 11.1 Power Supply Modes
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 接收文档更新通知
    2. 13.2 支持资源
    3. 13.3 Trademarks
    4. 13.4 Electrostatic Discharge Caution
    5. 13.5 术语表
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Low Voltage Signaling (LVS)

The TAS2764 monitors the absolute value of the audio stream.

When the input was initially above the programmed threshold set by LVS_FTH[4:0] register bits the Class D was supplied by PVDD rail. If the signal level drops below this threshold for longer than the hysteresis time defined by LVS_HYS[3:0] bits the Class-D supply will switch to VBAT1S.

The BYP_EN pin will be asserted (open drain released). All values of LVS_HYS[3:0] bit settings will ensure the remaining samples will be output before BYP_EN is asserted. When multiple devices have BYP_EN pin connected together, any device requiring a supply voltage higher than the threshold will pull the open drain output low.

When the signal level crosses above the programmed threshold set by LVS_FTH[4:0] bits the Class-D supply will switch to PVDD.

The open-drain BYP_EN pin will be de-asserted (actively pulling the output low) after a delay programmed by the LVS_DLY[1:0] register bits . The Y Bridge will switch from VBAT1S to PVDD after a delay programmed by the CDS_DLY[1:0] register bits.

LVS threshold is set based on the output signal level and is measured in dBFS.

The LVS threshold can alternately be configured to be a value relative to the VBAT1S voltage. To use the alternate configuration set the LVS_TMODE bit to high and use the LVS_RTH[3:0] register bits for setting the threshold.

Below equations show the maximum level of the input signal in order to keep LVS below threshold (Class D switching on VBAT).

For absolute threshold: Input (dBFS) < LVS_FTH + (21 dBV - ChannelGain [dBV]).

For relative threshold: Input (dBFS) < 20log10 (VBAT1S*CD_EFF - LVS_RTH) + (21 dBV - ChannelGain [dBV]) - 1.5dB.

Where:

* ChannelGain = AMP_LEVEL + DVC_LVL + SAFE_MODE (if enabled, it is -18dB).

* CD_EFF is set by registers 48h-4Bh from page 0x04 and LVH_RTH is set by bits [3:0] of register 6Ah from page 0x00.

* 1.5dB is an inflection factor, already included for absolute threshold.

BOP, Limiter, Thermal Foldback and Thermal Gradient Gain Attenuation should not be taken into account for calculating LV_EN threshold.

GUID-311B79C6-5EEC-4546-AA4A-76109946C49B-low.gif Figure 8-5 Low Voltage Signaling (Input=0dB, Gain=0dB)

The group delay numbers are optimized based on whether the Noise Gate feature is enabled or disabled. The delay on CDS_DLY path and LVS_DLY path varies depending on sampling rate and whether Noise Gate mode is enabled or not (see Section 8.9.91).

The LVS fixed thresholds, when CDS_MODE[1:0]=11 (PWR_MODE2 from Section 11.1), can be set using register bits LVS_FTH_LOW[1:0]. When CDS_MODE[1:0]=00 (PWR_MODE1 and PWR_MODE3 from Section 11.1) the thresholds should be set with register bits LVS_FTH[4:0].