ZHCSD04E November   2014  – March 2022 TPS65400

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 说明（续）
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 System Characteristics
    7. 7.7 Operational Parameters
    8. 7.8 Package Dissipation Ratings
    9. 7.9 Typical Characteristics: System Efficiency
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
      1. 8.3.1  Startup Timing and Power Sequencing
        1. 8.3.1.1 Startup Timing
        2. 8.3.1.2 External Sequencing
        3. 8.3.1.3 Internal Sequencing
      2. 8.3.2  UVLO and Precision Enables
      3. 8.3.3  Soft-Start and Prebiased Startup
        1. 8.3.3.1 Analog Soft-Start (Default) and Digital Soft-Start
        2. 8.3.3.2 Soft-Start Capacitor Selection
      4. 8.3.4  PWM Switching Frequency Selection
      5. 8.3.5  Clock Synchronization
      6. 8.3.6  Phase Interleaving
      7. 8.3.7  Fault Handling
      8. 8.3.8  OCP for SW1 to SW4
      9. 8.3.9  Overcurrent Protection for SW1 to SW4 in Current Sharing Operation
      10. 8.3.10 Recovery on Power Loss
      11. 8.3.11 Feedback Compensation
      12. 8.3.12 Adjusting Output Voltage
      13. 8.3.13 Digital Interface – PMBus
      14. 8.3.14 Initial Configuration
    4. 8.4 Device Functional Modes
      1. 8.4.1 CCM Operation Mode
      2. 8.4.2 CCM/DCM Operation Mode
      3. 8.4.3 Current Sharing Mode
    5. 8.5 Programming
      1. 8.5.1 PMBus
        1. 8.5.1.1 Overview
        2. 8.5.1.2 PMBus Protocol
          1. 8.5.1.2.1  PMBus Protocol
          2. 8.5.1.2.2  Transactions (No PEC)
          3. 8.5.1.2.3  Addressing
          4. 8.5.1.2.4  Startup
          5. 8.5.1.2.5  Bus Speed
          6. 8.5.1.2.6  I2CALERT Terminal
          7. 8.5.1.2.7  CONTROL Terminal
          8. 8.5.1.2.8  Packet Error Checking
          9. 8.5.1.2.9  Group Commands
          10. 8.5.1.2.10 Unsupported Features
      2. 8.5.2 PMBus Register Descriptions
        1. 8.5.2.1 Overview
        2. 8.5.2.2 Memory Model
        3. 8.5.2.3 Data Formats
        4. 8.5.2.4 Fault Monitoring
    6. 8.6 Register Maps
      1. 8.6.1 PMBus Core Commands
        1. 8.6.1.1  (00h) PAGE
        2. 8.6.1.2  (01h) OPERATION
        3. 8.6.1.3  (03h) CLEAR_FAULTS
        4. 8.6.1.4  (10h) WRITE_PROTECT
        5. 8.6.1.5  (11h) STORE_DEFAULT_ALL
        6. 8.6.1.6  (19h) CAPABILITY
        7. 8.6.1.7  (78h) STATUS_BYTE
        8. 8.6.1.8  (79h) STATUS_WORD
        9. 8.6.1.9  (7Ah) STATUS_VOUT
        10. 8.6.1.10 (80h) STATUS_MFR_SPECIFIC
        11. 8.6.1.11 (98h) PMBUS_REVISION
        12. 8.6.1.12 (ADh) IC_DEVICE_ID
        13. 8.6.1.13 (AEh) IC_DEVICE_REV
      2. 8.6.2 Manufacturer-Specific Commands
        1. 8.6.2.1  (D0h) USER_DATA_BYTE_00
        2. 8.6.2.2  (D1h) USER_DATA_BYTE_01
        3. 8.6.2.3  (D2h) PIN_CONFIG_00
        4. 8.6.2.4  (D3h) PIN_CONFIG_01
        5. 8.6.2.5  (D4h) SEQUENCE_CONFIG
        6. 8.6.2.6  (D5h) SEQUENCE_ORDER
        7. 8.6.2.7  (D6h) IOUT_MODE
        8. 8.6.2.8  (D7h) FREQUENCY_PHASE
        9. 8.6.2.9  (D8h) VREF_COMMAND
        10. 8.6.2.10 (D9h) IOUT_MAX
        11. 8.6.2.11 (DAh) USER_RAM_00
        12. 8.6.2.12 (DBh) SOFT_RESET
        13. 8.6.2.13 (DCh) RESET_DELAY
        14. 8.6.2.14 (DDh) TON_TOFF_DELAY
        15. 8.6.2.15 (DEh) TON_TRANSITION_RATE
        16. 8.6.2.16 (DFh) VREF_TRANSITION_RATE
        17. 8.6.2.17 (F0h) SLOPE_COMPENSATION
        18. 8.6.2.18 (F1h) ISENSE_GAIN
        19. 8.6.2.19 (FCh) DEVICE_CODE
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Internal Operation Typical Application
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Component Selection
            1. 9.2.1.2.1.1 Output Inductor Selection
            2. 9.2.1.2.1.2 Output Capacitor Selection
          2. 9.2.1.2.2 Internal Operation With Some Switchers Disabled
          3. 9.2.1.2.3 Internal Operation With All Switchers Enabled
          4. 9.2.1.2.4 Example Configuration
          5. 9.2.1.2.5 Unused Switchers
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Current Sharing Typical Application
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
          1. 9.2.2.2.1 Current Sharing Timing Example
      3. 9.2.3 External Sequencing Application
        1. 9.2.3.1 Design Requirements
        2. 9.2.3.2 Detailed Design Procedure
          1. 9.2.3.2.1 External Sequencing Through PG Pins
          2. 9.2.3.2.2 External Sequencing Through SW
          3. 9.2.3.2.3 Example Configuration
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
      2. 12.1.2 Related Parts
    2. 12.2 接收文档更新通知
    3. 12.3 术语表
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 术语表
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.6.1.2 (01h) OPERATION

The OPERATION command in conjunction with input from the enable pins ENSWx is used to turn on or off (enable or disable) the currently selected switching regulator as determined by the current PAGE. Margins are not supported. Data byte contents are given in Table 8-9.

Table 8-9 Operation Data Byte Contents
PAGE SUPPORTBITS [7:6]BITS [5:4]BITS [3:2]BITS [1:0]SEQUENCINGOUTPUT ON OR OFFDELAY
0x00 to 0x03, 0xFF00XXXXXXNoImmediate offNone
0x00 to 0x0301XXXXXXNoSoft offtOFF_DELAY
0xFF01XXXXXXYesSoft offtOFF_DELAY
0x00 to 0x031000XXXXNoOn with soft-start (default)tON_DELAY
0xFF1000XXXXYesOn with soft-start (default(1))tON_DELAY
(1) This is also the default behavior upon reset with active ENABLE selected (see (D2h) PIN_CONFIG_00)

Input from the enable pin overrides the off state of the corresponding output. The pin function configuration command PIN_CONFIG_00 can accept or ignore enable pins as well as disable OPERATION sequencing command support (see (01h_ OPERATION). If the OPERATION state is on, and PIN_CONFIG_00 is set to accept enable pins, action from enable pins would result in a delay specified by TON_TOFF_DELAY. Figure 8-27 shows how the on/off states are triggered.

GUID-5EF6289D-103C-4734-9498-6F0AE0E14FDC-low.gifFigure 8-27 On/Off Configuration (Per Output)

When a fault occurs, the output state will turn OFF and possibly attempt to turn ON repeatedly for persistent faults. Specific fault response behaviors are described in Section 8.3.7.

Note:

TI recommends that if OPERATION is to be used exclusively, all outputs should be set to the same order and enable pins should be ignored (see (D5h) SEQUENCE_ORDER, and (D2h) PIN_CONFIG_00).

The OPERATION parameter is not stored in the default store in data flash.