ZHCSNJ0G September   2006  – March 2021 PCA9538

PRODUCTION DATA  

  1. 特性
  2. 说明
  3. Revision History
  4. Pin Configuration and Functions
  5. Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 I2C Interface Timing Requirements
    7. 5.7 RESET Timing Requirements
    8. 5.8 Switching Characteristics
    9. 5.9 Typical Characteristics
  6. Parameter Measurement Information
  7. Detailed Description
    1. 7.1 Functional Block Diagram
    2. 7.2 Device Functional Modes
      1. 7.2.1 RESET Input
        1. 7.2.1.1 RESET Errata
          1.        System Impact
          2.        System Workaround
      2. 7.2.2 Power-On Reset
      3. 7.2.3 I/O Port
      4. 7.2.4 Interrupt Output ( INT)
        1. 7.2.4.1 Interrupt Errata
          1.        System Impact
          2.        System Workaround
    3. 7.3 Programming
      1. 7.3.1 I2C Interface
    4. 7.4 Register Maps
      1. 7.4.1 Device Address
      2. 7.4.2 Control Register And Command Byte
      3. 7.4.3 Register Descriptions
      4. 7.4.4 Bus Transactions
        1. 7.4.4.1 Writes
        2. 7.4.4.2 Reads
  8. Application Information Disclaimer
    1. 8.1 Application Information Disclaimer
    2. 8.2 Typical Application
      1. 8.2.1 Detailed Design Procedure
        1. 8.2.1.1 Minimizing ICC When I/Os Control Leds
  9. Power Supply Recommendations
    1. 9.1 Power-On Reset Requirements
  10. 10Device and Documentation Support
    1. 10.1 接收文档更新通知
    2. 10.2 支持资源
    3. 10.3 Trademarks
    4. 10.4 静电放电警告
    5. 10.5 术语表
  11. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Reads

The bus master first must send the PCA9538 address with the LSB set to a logic 0 (see Figure 7-6 for device address). The command byte is sent after the address and determines which register is accessed. After a restart, the device address is sent again but, this time, the LSB is set to a logic 1. Data from the register defined by the command byte then is sent by the PCA9538 (see Figure 7-10 and Figure 7-11). After a restart, the value of the register defined by the command byte matches the register being accessed when the restart occurred. Data is clocked into the register on the rising edge of the ACK clock pulse. There is no limitation on the number of data bytes received in one read transmission, but when the final byte is received, the bus master must not acknowledge the data.

GUID-C87ECF95-C92E-4868-9A2B-53D60A2749A0-low.gif Figure 7-10 Read From Register

GUID-07D1D5F2-1B3B-4129-957F-73E29595D273-low.gif
This figure assumes the command byte has previously been programmed with 00h.
Transfer of data can be stopped at any moment by a Stop condition.
This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address call and actual data transfer from the P port. See Figure 7-10 for these details.
Figure 7-11 Read From Input Port Register