SLVSJL6 June   2026 LM851772-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Handling Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Buck-Boost Control Scheme
        1. 8.3.1.1 Buck Mode
        2. 8.3.1.2 Boost Mode
        3. 8.3.1.3 Buck-Boost Mode
      2. 8.3.2  Power Save Mode
      3. 8.3.3  Reference System
        1. 8.3.3.1 Power On Reset and nRST-PIN
      4. 8.3.4  Internal VCC Regulators
        1. 8.3.4.1 VCC1 Regulator
        2. 8.3.4.2 VCC2 Regulator
      5. 8.3.5  Enable and Undervoltage Lockout
        1. 8.3.5.1 UVLO
      6. 8.3.6  Error Amplifier and Control
        1. 8.3.6.1 Output Voltage Regulation
        2. 8.3.6.2 Output Voltage Feedback
        3. 8.3.6.3 Voltage Regulation Loop
        4. 8.3.6.4 Dynamic Voltage Scaling
      7. 8.3.7  Output Voltage Discharge
      8. 8.3.8  Peak Current Sensor
      9. 8.3.9  Short Circuit - Hiccup Protection
      10. 8.3.10 Current Monitor/Limiter
        1. 8.3.10.1 Overview
        2. 8.3.10.2 Output Current Limitation
        3. 8.3.10.3 Output Current Monitor
      11. 8.3.11 Oscillator Frequency Selection
      12. 8.3.12 Frequency Synchronization
      13. 8.3.13 Output Voltage Tracking
        1. 8.3.13.1 Analog Voltage Tracking
        2. 8.3.13.2 Digital Voltage Tracking
      14. 8.3.14 Slope Compensation
      15. 8.3.15 Configurable Soft Start
      16. 8.3.16 Drive Pin
      17. 8.3.17 Dual Random Spread Spectrum – DRSS
      18. 8.3.18 Gate Driver
      19. 8.3.19 Cable Drop Compensation (CDC)
      20. 8.3.20 CFG-Pin and R2D Interface
      21. 8.3.21 Advanced Monitoring Features
        1. 8.3.21.1  Overview
        2. 8.3.21.2  BUSY
        3. 8.3.21.3  OFF
        4. 8.3.21.4  VOUT
        5. 8.3.21.5  IOUT
        6. 8.3.21.6  INPUT
        7. 8.3.21.7  TEMPERATURE
        8. 8.3.21.8  CML
        9. 8.3.21.9  OTHER
        10. 8.3.21.10 ILIM_OP
        11. 8.3.21.11 nFLT/nINT Pin Output
        12. 8.3.21.12 Status Byte
      22. 8.3.22 Protection Features
        1. 8.3.22.1 Thermal Shutdown (TSD)
        2. 8.3.22.2 Overcurrent Protection
        3. 8.3.22.3 Output Overvoltage Protection 1 (OVP1)
        4. 8.3.22.4 Output Overvoltage Protection 2 (OVP2)
        5. 8.3.22.5 Input Voltage Protection (IVP)
        6. 8.3.22.6 Power Good
        7. 8.3.22.7 Boot-Strap Undervoltage Protection
        8. 8.3.22.8 Boot-strap Overvoltage Clamp
        9. 8.3.22.9 CRC - CHECK
    4. 8.4 Device Functional Modes
      1. 8.4.1 Overview
      2. 8.4.2 Logic State Description
    5. 8.5 Programming
      1. 8.5.1 I2C Bus Operation
      2. 8.5.2 Clock Stretching
      3. 8.5.3 Data Transfer Formats
      4. 8.5.4 Single READ From a Defined Register Address
      5. 8.5.5 Sequential READ Starting from a Defined Register Address
      6. 8.5.6 Single WRITE to a Defined Register Address
      7. 8.5.7 Sequential WRITE Starting at a Defined Register Address
  10. 9 LM851772-Q1 Registers
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1  Custom Design with WEBENCH Tools
        2. 10.2.2.2  Frequency
        3. 10.2.2.3  Feedback Divider
        4. 10.2.2.4  Inductor and Current Sense Resistor Selection
        5. 10.2.2.5  Output Capacitor
        6. 10.2.2.6  Input Capacitor
        7. 10.2.2.7  Slope Compensation
        8. 10.2.2.8  UVLO Divider
        9. 10.2.2.9  Soft-Start Capacitor
        10. 10.2.2.10 nRST and EN/UVLO Pull-up Resistor Selection
        11. 10.2.2.11 MOSFETs QH1 and QL1
        12. 10.2.2.12 MOSFETs QH2 and QL2
        13. 10.2.2.13 Loop Compensation
        14. 10.2.2.14 External Component Selection
      3. 10.2.3 Application Curves
    3. 10.3 USB-PD Source with Power Path
    4. 10.4 Parallel (Multiphase) Operation
    5. 10.5 Wireless Charging Supply
    6. 10.6 Power Supply Recommendations
    7. 10.7 Layout
      1. 10.7.1 Layout Guidelines
        1. 10.7.1.1 Power Stage Layout
        2. 10.7.1.2 Gate Driver Layout
        3. 10.7.1.3 Controller Layout
      2. 10.7.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information
    1. 13.1 Tape and Reel Information
    2.     132

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • RHA|40
散热焊盘机械数据 (封装 | 引脚)

8.1 Overview

The LM851772-Q1 is a four switch Buck-Boost controller. The device provides a regulated output voltage if the input voltage is higher, equal or lower as the adjusted output voltage. In power-save mode the device supports a high efficiency over the full range of the output load.

The LM851772-Q1 runs at a fixed switching frequency (in fPWM), which is set via the RT and SYNC pin. The switching frequency remains constant during buck, boost and buck-boost operation. The device maintains small mode transition ripple over all operating modes.

programming the output voltage and device configurations dynamically using the integrated I2C interface is possible. The integrated and optional high side current sensor features an accurate and output current limitation. The average current limit of the LM851772-Q1 is also configurable through the I2C interface.