ZHCSAB9E September   2012  – June 2019 DP83848-EP

PRODUCTION DATA.  

  1. 1 器件概述
    1. 1.1 特性
    2. 1.2 应用
    3. 1.3 说明
    4. 1.4 功能方框图
      1.      典型系统图
  2. 2 修订历史记录
  3. 3 Pin Configuration and Functions
    1. 3.1 Package Pin Assignments
  4. 4 Specifications
    1. 4.1 Absolute Maximum Ratings
    2. 4.2 ESD Ratings
    3. 4.3 Recommended Operating Conditions
    4. 4.4 Thermal Information
    5. 4.5 DC Specifications
      1. 4.5.1 Electrical Characteristics
    6. 4.6 AC Specifications
      1. 4.6.1  Power Up Timing
      2. 4.6.2  Reset Timing
      3. 4.6.3  MII Serial Management Timing
      4. 4.6.4  100-Mbps MII Transmit Timing
      5. 4.6.5  100-Mbps MII Receive Timing
      6. 4.6.6  100BASE-TX Transmit Packet Latency Timing
      7. 4.6.7  100BASE-TX Transmit Packet Deassertion Timing
      8. 4.6.8  100BASE-TX Transmit Timing (tR/F and Jitter)
      9. 4.6.9  100BASE-TX Receive Packet Latency Timing
      10. 4.6.10 100BASE-TX Receive Packet Deassertion Timing
      11. 4.6.11 10-Mbps MII Transmit Timing
      12. 4.6.12 10-Mbps MII Receive Timing
      13. 4.6.13 10-Mbps Serial Mode Transmit Timing
      14. 4.6.14 10-Mbps Serial Mode Receive Timing
      15. 4.6.15 10BASE-T Transmit Timing (Start of Packet)
      16. 4.6.16 10BASE-T Transmit Timing (End of Packet)
      17. 4.6.17 10BASE-T Receive Timing (Start of Packet)
      18. 4.6.18 10BASE-T Receive Timing (End of Packet)
      19. 4.6.19 10-Mbps Heartbeat Timing
      20. 4.6.20 10-Mbps Jabber Timing
      21. 4.6.21 10BASE-T Normal Link Pulse Timing
      22. 4.6.22 Auto-Negotiation Fast Link Pulse (FLP) Timing
      23. 4.6.23 100BASE-TX Signal Detect Timing
      24. 4.6.24 100-Mbps Internal Loopback Timing
      25. 4.6.25 10-Mbps Internal Loopback Timing
      26. 4.6.26 RMII Transmit Timing
      27. 4.6.27 RMII Receive Timing
      28. 4.6.28 Isolation Timing
      29. 4.6.29 25MHz_OUT Timing
  5. 5 Detailed Description
    1. 5.1 Overview
    2. 5.2 Functional Block Diagram
    3. 5.3 Feature Description
      1. 5.3.1 Auto-Negotiation
        1. 5.3.1.1 Auto-Negotiation Pin Control
        2. 5.3.1.2 Auto-Negotiation Register Control
        3. 5.3.1.3 Auto-Negotiation Parallel Detection
        4. 5.3.1.4 Auto-Negotiation Restart
        5. 5.3.1.5 Enabling Auto-Negotiation via Software
        6. 5.3.1.6 Auto-Negotiation Complete Time
      2. 5.3.2 Auto-MDIX
      3. 5.3.3 LED Interface
        1. 5.3.3.1 LEDs
        2. 5.3.3.2 LED Direct Control
      4. 5.3.4 Internal Loopback
      5. 5.3.5 BIST
      6. 5.3.6 Energy Detect Mode
    4. 5.4 Device Functional Modes
      1. 5.4.1 MII Interface
        1. 5.4.1.1 Nibble-wide MII Data Interface
        2. 5.4.1.2 Collision Detect
        3. 5.4.1.3 Carrier Sense
      2. 5.4.2 Reduced MII Interface
        1. 5.4.2.1 10 Mb Serial Network Interface (SNI)
      3. 5.4.3 802.3u MII Serial Management Interface
        1. 5.4.3.1 Serial Management Register Access
        2. 5.4.3.2 Serial Management Access Protocol
        3. 5.4.3.3 Serial Management Preamble Suppression
      4. 5.4.4 PHY Address
        1. 5.4.4.1 MII Isolate Mode
      5. 5.4.5 Half Duplex vs Full Duplex
      6. 5.4.6 Reset Operation
        1. 5.4.6.1 Hardware Reset
        2. 5.4.6.2 Software Reset
    5. 5.5 Programming
      1. 5.5.1 Architecture
        1. 5.5.1.1 100BASE-TX Transmitter
          1. 5.5.1.1.1 Code-Group Encoding and Injection
          2. 5.5.1.1.2 Scrambler
          3. 5.5.1.1.3 NRZ to NRZI Encoder
          4. 5.5.1.1.4 Binary to MLT-3 Convertor
        2. 5.5.1.2 100BASE-TX Receiver
          1. 5.5.1.2.1  Analog Front End
          2. 5.5.1.2.2  Digital Signal Processor
            1. 5.5.1.2.2.1 Digital Adaptive Equalization and Gain Control
            2. 5.5.1.2.2.2 Base Line Wander Compensation
          3. 5.5.1.2.3  Signal Detect
          4. 5.5.1.2.4  MLT-3 to NRZI Decoder
          5. 5.5.1.2.5  NRZI to NRZ
          6. 5.5.1.2.6  Serial to Parallel
          7. 5.5.1.2.7  Descrambler
          8. 5.5.1.2.8  Code-group Alignment
          9. 5.5.1.2.9  4B/5B Decoder
          10. 5.5.1.2.10 100BASE-TX Link Integrity Monitor
          11. 5.5.1.2.11 Bad SSD Detection
        3. 5.5.1.3 10BASE-T Transceiver Module
          1. 5.5.1.3.1  Operational Modes
            1. 5.5.1.3.1.1 Half Duplex Mode
            2. 5.5.1.3.1.2 Full Duplex Mode
          2. 5.5.1.3.2  Smart Squelch
          3. 5.5.1.3.3  Collision Detection and SQE
          4. 5.5.1.3.4  Carrier Sense
          5. 5.5.1.3.5  Normal Link Pulse Detection and Generation
          6. 5.5.1.3.6  Jabber Function
          7. 5.5.1.3.7  Automatic Link Polarity Detection and Correction
          8. 5.5.1.3.8  Transmit and Receive Filtering
          9. 5.5.1.3.9  Transmitter
          10. 5.5.1.3.10 Receiver
    6. 5.6 Memory
      1. 5.6.1 Register Definition
        1. 5.6.1.1 Basic Mode Control Register (BMCR)
        2. 5.6.1.2 Basic Mode Status Register (BMSR)
        3. 5.6.1.3 PHY Identifier Register #1 (PHYIDR1)
        4. 5.6.1.4 PHY Identifier Register #2 (PHYIDR2)
        5. 5.6.1.5 Auto-Negotiation Advertisement Register (ANAR)
        6. 5.6.1.6 Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)
        7. 5.6.1.7 Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page)
        8. 5.6.1.8 Auto-Negotiate Expansion Register (ANER)
        9. 5.6.1.9 Auto-Negotiation Next Page Transmit Register (ANNPTR)
      2. 5.6.2 Extended Registers
        1. 5.6.2.1  PHY Status Register (PHYSTS)
        2. 5.6.2.2  MII Interrupt Control Register (MICR)
        3. 5.6.2.3  MII Interrupt Status and Miscellaneous Control Register (MISR)
        4. 5.6.2.4  False Carrier Sense Counter Register (FCSCR)
        5. 5.6.2.5  Receiver Error Counter Register (RECR)
        6. 5.6.2.6  100 Mbps PCS Configuration and Status Register (PCSR)
        7. 5.6.2.7  RMII and Bypass Register (RBR)
        8. 5.6.2.8  LED Direct Control Register (LEDCR)
        9. 5.6.2.9  PHY Control Register (PHYCR)
        10. 5.6.2.10 10Base-T Status/Control Register (10BTSCR)
        11. 5.6.2.11 CD Test and BIST Extensions Register (CDCTRL1)
        12. 5.6.2.12 Energy Detect Control (EDCR)
  6. 6 Application and Implementation
    1. 6.1 Application Information
    2. 6.2 Typical Application
      1. 6.2.1 Design Requirements
        1. 6.2.1.1 TPI Network Circuit
        2. 6.2.1.2 Clock IN (X1) Requirements
        3. 6.2.1.3 Power Feedback Circuit
        4. 6.2.1.4 Power Down and Interrupt
          1. 6.2.1.4.1 Power Down Control Mode
          2. 6.2.1.4.2 Interrupt Mechanisms
        5. 6.2.1.5 Magnetics
      2. 6.2.2 Detailed Design Procedure
        1. 6.2.2.1 MAC Interface (MII/RMII)
        2. 6.2.2.2 Termination Requirement
        3. 6.2.2.3 Recommended Maximum Trace Length
        4. 6.2.2.4 Calculating Impedance
      3. 6.2.3 Application Curves
  7. 7 Power Supply Recommendations
  8. 8 Layout
    1. 8.1 Layout Guidelines
      1. 8.1.1 PCB Layout Considerations
      2. 8.1.2 PCB Layer Stacking
    2. 8.2 Layout Example
    3. 8.3 Thermal Vias Recommendation
  9. 9 器件和文档支持
    1. 9.1 文档支持
      1. 9.1.1 相关文档
    2. 9.2 Community Resources
    3. 9.3 商标
    4. 9.4 静电放电警告
    5. 9.5 Export Control Notice
    6. 9.6 Glossary
  10. 10机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

5.5.1.1 100BASE-TX Transmitter

The 100BASE-TX transmitter consists of several functional blocks which convert synchronous 4-bit nibble data, as provided by the MII, to a scrambled MLT-3 125-Mbps serial data stream. Because the 100BASE-TX TP-PMD is integrated, the differential output pins, PMD Output Pair, can be directly routed to the magnetics. The block diagram in Figure 5-5 provides an overview of each functional block within the 100BASE-TX transmit section.

The Transmitter section consists of the following functional blocks:

  • Code-group Encoder and Injection block
  • Scrambler block (bypass option)
  • NRZ to NRZI encoder block
  • Binary to MLT-3 converter / Common Driver

The bypass option for the functional blocks within the 100BASE-TX transmitter provides flexibility for applications where data conversion is not always required. The DP83848-EP implements the 100BASE-TX transmit state machine diagram as specified in the IEEE 802.3u Standard, Clause 24.

DP83848-EP 30152506.pngFigure 5-5 100BASE-TX Transmit Block Diagram

Table 5-6 4B5B Code-Group Encoding/Decoding

DATA CODES
0 11110 0000
1 01001 0001
2 10100 0010
3 10101 0011
4 01010 0100
5 01011 0101
6 01110 0110
7 01111 0111
8 10010 1000
9 10011 1001
A 10110 1010
B 10111 1011
C 11010 1100
D 11011 1101
E 11100 1110
F 11101 1111
IDLE AND CONTROL CODES
H 00100 HALT code-group - Error code
I 11111 Inter-Packet IDLE - 0000(1)
J 11000 First Start of Packet - 0101(1)
K 10001 Second Start of Packet - 0101(1)
T 01101 First End of Packet - 0000(1)
R 00111 Second End of Packet - 0000(1)
INVALID CODES
V 00000
V 00001
V 00010
V 00011
V 00101
V 00110
V 01000
V 01100
(1) Control code-groups I, J, K, T, and R in data fields will be mapped as invalid codes, together with RX_ER asserted.