ZHCSNP0A august   2020  – march 2021 BQ25171-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 典型特性
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Device Power Up from Input Source
        1. 7.3.1.1 ISET Pin Detection
        2. 7.3.1.2 CHM_TMR Pin Detection
        3. 7.3.1.3 VSET Pin Detection
        4. 7.3.1.4 Charger Power Up
      2. 7.3.2 Battery Charging Features
        1. 7.3.2.1 Lithium-Ion Battery Charging Profile
          1. 7.3.2.1.1 NiMH Battery Charging Profile
        2. 7.3.2.2 Charge Termination and Battery Recharge
        3. 7.3.2.3 Charging Safety Timers
        4. 7.3.2.4 Battery Cold, Hot Temperature Qualification (TS Pin)
      3. 7.3.3 Status Outputs (STAT1, STAT2)
        1. 7.3.3.1 Charging Status Indicator (STAT1, STAT2)
      4. 7.3.4 Protection Features
        1. 7.3.4.1 Input Overvoltage Protection (VIN OVP)
        2. 7.3.4.2 Output Overvoltage Protection (BAT OVP)
        3. 7.3.4.3 Output Overcurrent Protection (BAT OCP)
        4. 7.3.4.4 Thermal Regulation and Thermal Shutdown (TREG and TSHUT)
    4. 7.4 Device Functional Modes
      1. 7.4.1 Shutdown or Undervoltage Lockout (UVLO)
      2. 7.4.2 Sleep Mode
      3. 7.4.3 Active Mode
        1. 7.4.3.1 Standby Mode
      4. 7.4.4 Fault Mode
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 1s LiFePO4 Charger Design Example
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Program the Fast Charge Current, ISET:
          2. 8.2.1.2.2 TS Function
        3. 8.2.1.3 Application Curves
      2. 8.2.2 2s Li-Ion Charger with Power Path Design Example
        1. 8.2.2.1 Design Requirements
      3. 8.2.3 4s NiMH Charger Design Example
        1. 8.2.3.1 Design Requirements
  10. 9 Power Supply Recommendations
  11. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 第三方产品免责声明
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 支持资源
    4. 11.4 Trademarks
    5. 11.5 静电放电警告
    6. 11.6 术语表
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.3.1.3 VSET Pin Detection

VSET pin is used to program the device regulation voltage at end-of-charge using a ±1% pulldown resistor. The available pulldown resistor and corresponding charging levels are:

Table 7-2 VSET Pin Resistor Value Table
RESISTOR Li+ CONFIGURATION NiMH CONFIGURATION
CHARGE VOLTAGE (V) CELL COUNT
> 150 kΩ No charge (open-circuit) No charge (open-circuit)
100 kΩ 1-cell LiFePO4: 3.50 V No charge (open-circuit)
82 kΩ 1-cell LiFePO4: 3.60 V No charge (open-circuit)
62 kΩ 1-cell LiFePO4: 3.70 V 1-cell
47 kΩ 1-cell LiIon: 3.80 V 1-cell + intermittent charge
36 kΩ 1-cell LiIon: 3.90 V 2-cell
27 kΩ 1-cell LiIon: 4.05 V 2-cell + intermittent charge
24 kΩ 1-cell LiIon: 4.10 V 3-cell
18 kΩ 1-cell LiIon: 4.20 V 3-cell + intermittent charge
15 kΩ 1-cell LiIon: 4.35 V 4-cell
11 kΩ 2-cell LiFePO4: 7.00 V 4-cell + intermittent charge
8.2 kΩ 2-cell LiFePO4: 7.20 V 5-cell
6.2 kΩ 2-cell LiFePO4: 7.40 V 5-cell + intermittent charge
4.7 kΩ 2-cell LiIon: 8.20 V 6-cell
3.6 kΩ 2-cell LiIon: 8.40 V 6-cell + intermittent charge
< 3.0 kΩ No charge (short-circuit) No charge (short-circuit)

If either a short- or open-circuit condition is detected, charger stops operation and remains in the FAULT state until the input or CE pin is toggled.

Once a valid resistor value has been detected, the corresponding charge voltage is latched in and the pin is not continuously monitored during operation. A change in this pin will not be acknowledged by the IC until the input supply or CE pin is toggled.