ZHCSGO0A June   2017  – February 2024 TPS549B22

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 25-A FET
      2. 6.3.2 On-Resistance
      3. 6.3.3 Package Size, Efficiency and Thermal Performance
      4. 6.3.4 Soft-Start Operation
      5. 6.3.5 VDD Supply Undervoltage Lockout (UVLO) Protection
      6. 6.3.6 EN_UVLO Pin Functionality
      7. 6.3.7 Fault Protections
        1. 6.3.7.1 Current Limit (ILIM) Functionality
        2. 6.3.7.2 VDD Undervoltage Lockout (UVLO)
        3. 6.3.7.3 Overvoltage Protection (OVP) and Undervoltage Protection (UVP)
        4. 6.3.7.4 Out-of-Bounds Operation
        5. 6.3.7.5 Overtemperature Protection
    4. 6.4 Device Functional Modes
      1. 6.4.1 D-CAP3™ Control Mode Topology
      2. 6.4.2 DCAP Control Topology
    5. 6.5 Programming
      1. 6.5.1 Programmable Pin-Strap Settings
        1. 6.5.1.1 Address Selection (ADDR) Pin
        2. 6.5.1.2 VSEL Pin
        3. 6.5.1.3 D-CAP3™ Control Mode Selection
        4. 6.5.1.4 Application Workaround to Support 4-ms and 8-ms SS Settings
      2. 6.5.2 Programmable Analog Configurations
        1. 6.5.2.1 RSP/RSN Remote Sensing Functionality
          1. 6.5.2.1.1 Output Differential Remote Sensing Amplifier
        2. 6.5.2.2 Power Good (PGOOD Pin) Functionality
      3. 6.5.3 PMBus Programming
        1. 6.5.3.1 TPS549B22 Limitations to the PMBUS Specifications
        2. 6.5.3.2 Target Address Assignment
        3. 6.5.3.3 PMBUS Address Selection
        4. 6.5.3.4 Supported Formats
          1. 6.5.3.4.1 Direct Format — Write
          2. 6.5.3.4.2 Combined Format — Read
        5. 6.5.3.5 Stop Separated Reads
        6. 6.5.3.6 Supported PMBUS Commands and Registers
  8. 7 Register Maps
    1. 7.1  OPERATION Register (address = 1h)
    2. 7.2  ON_OFF_CONFIG Register (address = 2h)
    3. 7.3  CLEAR FAULTS (address = 3h)
    4. 7.4  WRITE PROTECT (address = 10h)
    5. 7.5  STORE_DEFAULT_ALL (address = 11h)
    6. 7.6  RESTORE_DEFAULT_ALL (address = 12h)
    7. 7.7  CAPABILITY (address = 19h)
    8. 7.8  VOUT_MODE (address = 20h)
    9. 7.9  VOUT_COMMAND (address = 21h)
    10. 7.10 VOUT_MARGIN_HIGH (address = 25h) ®
    11. 7.11 VOUT_MARGIN_LOW (address = 26h)
    12. 7.12 STATUS_BYTE (address = 78h)
    13. 7.13 STATUS_WORD (High Byte) (address = 79h)
    14. 7.14 STATUS_VOUT (address = 7Ah)
    15. 7.15 STATUS_IOUT (address = 7Bh)
    16. 7.16 STATUS_CML (address = 7Eh)
    17. 7.17 MFR_SPECIFIC_00 (address = D0h)
    18. 7.18 MFR_SPECIFIC_01 (address = D1h)
    19. 7.19 MFR_SPECIFIC_02 (address = D2h)
    20. 7.20 MFR_SPECIFIC_03 (address = D3h)
    21. 7.21 MFR_SPECIFIC_04 (address = D4h)
    22. 7.22 MFR_SPECIFIC_06 (address = D6h)
    23. 7.23 MFR_SPECIFIC_07 (address = D7h)
    24. 7.24 MFR_SPECIFIC_44 (address = FCh)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 TPS549B22 1.5-V to 18-V Input, 1-V Output, 25-A Converter
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1  Custom Design With WEBENCH® Tools
        2. 8.2.3.2  Switching Frequency Selection
        3. 8.2.3.3  Inductor Selection
        4. 8.2.3.4  Output Capacitor Selection
          1. 8.2.3.4.1 Minimum Output Capacitance to Make Sure of Stability
          2. 8.2.3.4.2 Response to a Load Transient
          3. 8.2.3.4.3 Output Voltage Ripple
        5. 8.2.3.5  Input Capacitor Selection
        6. 8.2.3.6  Bootstrap Capacitor Selection
        7. 8.2.3.7  BP Pin
        8. 8.2.3.8  R-C Snubber and VIN Pin High-Frequency Bypass
        9. 8.2.3.9  Optimize Reference Voltage (VSEL)
        10. 8.2.3.10 MODE Pin Selection
        11. 8.2.3.11 ADDR Pin Selection
        12. 8.2.3.12 Overcurrent Limit Design
      4. 8.2.4 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Examples
      3. 8.4.3 Mounting and Thermal Profile Recommendation
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
        1. 9.1.1.1 Custom Design With WEBENCH® Tools
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 接收文档更新通知
    4. 9.4 支持资源
    5. 9.5 Trademarks
    6. 9.6 静电放电警告
    7. 9.7 术语表
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • RVF|40
散热焊盘机械数据 (封装 | 引脚)
订购信息

4 Pin Configuration and Functions

GUID-512DD049-7988-4D7F-A39F-08D25E15C7CE-low.gifFigure 4-1 RVF Package40-Pin LQFN-CLIP With Thermal PadTop View
Table 4-1 Pin Functions
PINTYPE(1)DESCRIPTION
NAMENO.
ADDR32IProgram device address and SKIP or FCCM mode.
AGND30GGround pin for internal analog circuits.
BOOT5PSupply rail for high-side gate driver (boot terminal). Connect boot capacitor from this pin to SW node. Internally connected to BP via bootstrap PMOS switch.
BP31OLDO output
DRGND29PInternal gate driver return.
EN_UVLO4IEnable pin that can turn on the DC/DC switching converter. Use also to program the required PVIN UVLO when PVIN and VDD are connected together.
ILIM36I/OProgram overcurrent limit by connecting a resistor to ground.
MODE34IMode selection pin. Select the control mode, and soft-start timing selection.
NC6, 7, 26, 27No connect.
PGND13, 14, 15, 16, 17, 18, 19, 20PPower ground of internal FETs.
PGOOD35OOpen drain power-good status signal.
PMB_CLK3IClock input for the PMBus interface.
PMB_DATA2I/OData I/O for the PMBus interface.
PVIN21, 22, 23, 24, 25PPower supply input for integrated power MOSFET pair.
RSN38IInverting input of the differential remote sense amplifier.
RSP39INon-inverting input of the differential remote sense amplifier.
RESV_TRK37IDo not connect.
SMB_ALRT#1OAlert output for the PMBus interface.
SW8, 9, 10, 11, 12I/OOutput switching terminal of power converter. Connect the pins to the output inductor.
VDD28PController power supply input.
VOSNS40IOutput voltage monitor input pin.
VSEL33IProgram the initial start-up and or reference voltage without feedback resistor dividers (from 0.6 V to 1.2 V in 50-mV increments).
(1) I = input, O = output, G = GND