ZHCSAB9E September   2012  – June 2019 DP83848-EP

PRODUCTION DATA.  

  1. 器件概述
    1. 1.1 特性
    2. 1.2 应用
    3. 1.3 说明
    4. 1.4 功能方框图
      1.      典型系统图
  2. 修订历史记录
  3. Pin Configuration and Functions
    1. 3.1 Package Pin Assignments
  4. Specifications
    1. 4.1 Absolute Maximum Ratings
    2. 4.2 ESD Ratings
    3. 4.3 Recommended Operating Conditions
    4. 4.4 Thermal Information
    5. 4.5 DC Specifications
      1. 4.5.1 Electrical Characteristics
    6. 4.6 AC Specifications
      1. 4.6.1  Power Up Timing
      2. 4.6.2  Reset Timing
      3. 4.6.3  MII Serial Management Timing
      4. 4.6.4  100-Mbps MII Transmit Timing
      5. 4.6.5  100-Mbps MII Receive Timing
      6. 4.6.6  100BASE-TX Transmit Packet Latency Timing
      7. 4.6.7  100BASE-TX Transmit Packet Deassertion Timing
      8. 4.6.8  100BASE-TX Transmit Timing (tR/F and Jitter)
      9. 4.6.9  100BASE-TX Receive Packet Latency Timing
      10. 4.6.10 100BASE-TX Receive Packet Deassertion Timing
      11. 4.6.11 10-Mbps MII Transmit Timing
      12. 4.6.12 10-Mbps MII Receive Timing
      13. 4.6.13 10-Mbps Serial Mode Transmit Timing
      14. 4.6.14 10-Mbps Serial Mode Receive Timing
      15. 4.6.15 10BASE-T Transmit Timing (Start of Packet)
      16. 4.6.16 10BASE-T Transmit Timing (End of Packet)
      17. 4.6.17 10BASE-T Receive Timing (Start of Packet)
      18. 4.6.18 10BASE-T Receive Timing (End of Packet)
      19. 4.6.19 10-Mbps Heartbeat Timing
      20. 4.6.20 10-Mbps Jabber Timing
      21. 4.6.21 10BASE-T Normal Link Pulse Timing
      22. 4.6.22 Auto-Negotiation Fast Link Pulse (FLP) Timing
      23. 4.6.23 100BASE-TX Signal Detect Timing
      24. 4.6.24 100-Mbps Internal Loopback Timing
      25. 4.6.25 10-Mbps Internal Loopback Timing
      26. 4.6.26 RMII Transmit Timing
      27. 4.6.27 RMII Receive Timing
      28. 4.6.28 Isolation Timing
      29. 4.6.29 25MHz_OUT Timing
  5. Detailed Description
    1. 5.1 Overview
    2. 5.2 Functional Block Diagram
    3. 5.3 Feature Description
      1. 5.3.1 Auto-Negotiation
        1. 5.3.1.1 Auto-Negotiation Pin Control
        2. 5.3.1.2 Auto-Negotiation Register Control
        3. 5.3.1.3 Auto-Negotiation Parallel Detection
        4. 5.3.1.4 Auto-Negotiation Restart
        5. 5.3.1.5 Enabling Auto-Negotiation via Software
        6. 5.3.1.6 Auto-Negotiation Complete Time
      2. 5.3.2 Auto-MDIX
      3. 5.3.3 LED Interface
        1. 5.3.3.1 LEDs
        2. 5.3.3.2 LED Direct Control
      4. 5.3.4 Internal Loopback
      5. 5.3.5 BIST
      6. 5.3.6 Energy Detect Mode
    4. 5.4 Device Functional Modes
      1. 5.4.1 MII Interface
        1. 5.4.1.1 Nibble-wide MII Data Interface
        2. 5.4.1.2 Collision Detect
        3. 5.4.1.3 Carrier Sense
      2. 5.4.2 Reduced MII Interface
        1. 5.4.2.1 10 Mb Serial Network Interface (SNI)
      3. 5.4.3 802.3u MII Serial Management Interface
        1. 5.4.3.1 Serial Management Register Access
        2. 5.4.3.2 Serial Management Access Protocol
        3. 5.4.3.3 Serial Management Preamble Suppression
      4. 5.4.4 PHY Address
        1. 5.4.4.1 MII Isolate Mode
      5. 5.4.5 Half Duplex vs Full Duplex
      6. 5.4.6 Reset Operation
        1. 5.4.6.1 Hardware Reset
        2. 5.4.6.2 Software Reset
    5. 5.5 Programming
      1. 5.5.1 Architecture
        1. 5.5.1.1 100BASE-TX Transmitter
          1. 5.5.1.1.1 Code-Group Encoding and Injection
          2. 5.5.1.1.2 Scrambler
          3. 5.5.1.1.3 NRZ to NRZI Encoder
          4. 5.5.1.1.4 Binary to MLT-3 Convertor
        2. 5.5.1.2 100BASE-TX Receiver
          1. 5.5.1.2.1  Analog Front End
          2. 5.5.1.2.2  Digital Signal Processor
            1. 5.5.1.2.2.1 Digital Adaptive Equalization and Gain Control
            2. 5.5.1.2.2.2 Base Line Wander Compensation
          3. 5.5.1.2.3  Signal Detect
          4. 5.5.1.2.4  MLT-3 to NRZI Decoder
          5. 5.5.1.2.5  NRZI to NRZ
          6. 5.5.1.2.6  Serial to Parallel
          7. 5.5.1.2.7  Descrambler
          8. 5.5.1.2.8  Code-group Alignment
          9. 5.5.1.2.9  4B/5B Decoder
          10. 5.5.1.2.10 100BASE-TX Link Integrity Monitor
          11. 5.5.1.2.11 Bad SSD Detection
        3. 5.5.1.3 10BASE-T Transceiver Module
          1. 5.5.1.3.1  Operational Modes
            1. 5.5.1.3.1.1 Half Duplex Mode
            2. 5.5.1.3.1.2 Full Duplex Mode
          2. 5.5.1.3.2  Smart Squelch
          3. 5.5.1.3.3  Collision Detection and SQE
          4. 5.5.1.3.4  Carrier Sense
          5. 5.5.1.3.5  Normal Link Pulse Detection and Generation
          6. 5.5.1.3.6  Jabber Function
          7. 5.5.1.3.7  Automatic Link Polarity Detection and Correction
          8. 5.5.1.3.8  Transmit and Receive Filtering
          9. 5.5.1.3.9  Transmitter
          10. 5.5.1.3.10 Receiver
    6. 5.6 Memory
      1. 5.6.1 Register Definition
        1. 5.6.1.1 Basic Mode Control Register (BMCR)
        2. 5.6.1.2 Basic Mode Status Register (BMSR)
        3. 5.6.1.3 PHY Identifier Register #1 (PHYIDR1)
        4. 5.6.1.4 PHY Identifier Register #2 (PHYIDR2)
        5. 5.6.1.5 Auto-Negotiation Advertisement Register (ANAR)
        6. 5.6.1.6 Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)
        7. 5.6.1.7 Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page)
        8. 5.6.1.8 Auto-Negotiate Expansion Register (ANER)
        9. 5.6.1.9 Auto-Negotiation Next Page Transmit Register (ANNPTR)
      2. 5.6.2 Extended Registers
        1. 5.6.2.1  PHY Status Register (PHYSTS)
        2. 5.6.2.2  MII Interrupt Control Register (MICR)
        3. 5.6.2.3  MII Interrupt Status and Miscellaneous Control Register (MISR)
        4. 5.6.2.4  False Carrier Sense Counter Register (FCSCR)
        5. 5.6.2.5  Receiver Error Counter Register (RECR)
        6. 5.6.2.6  100 Mbps PCS Configuration and Status Register (PCSR)
        7. 5.6.2.7  RMII and Bypass Register (RBR)
        8. 5.6.2.8  LED Direct Control Register (LEDCR)
        9. 5.6.2.9  PHY Control Register (PHYCR)
        10. 5.6.2.10 10Base-T Status/Control Register (10BTSCR)
        11. 5.6.2.11 CD Test and BIST Extensions Register (CDCTRL1)
        12. 5.6.2.12 Energy Detect Control (EDCR)
  6. Application and Implementation
    1. 6.1 Application Information
    2. 6.2 Typical Application
      1. 6.2.1 Design Requirements
        1. 6.2.1.1 TPI Network Circuit
        2. 6.2.1.2 Clock IN (X1) Requirements
        3. 6.2.1.3 Power Feedback Circuit
        4. 6.2.1.4 Power Down and Interrupt
          1. 6.2.1.4.1 Power Down Control Mode
          2. 6.2.1.4.2 Interrupt Mechanisms
        5. 6.2.1.5 Magnetics
      2. 6.2.2 Detailed Design Procedure
        1. 6.2.2.1 MAC Interface (MII/RMII)
        2. 6.2.2.2 Termination Requirement
        3. 6.2.2.3 Recommended Maximum Trace Length
        4. 6.2.2.4 Calculating Impedance
      3. 6.2.3 Application Curves
  7. Power Supply Recommendations
  8. Layout
    1. 8.1 Layout Guidelines
      1. 8.1.1 PCB Layout Considerations
      2. 8.1.2 PCB Layer Stacking
    2. 8.2 Layout Example
    3. 8.3 Thermal Vias Recommendation
  9. 器件和文档支持
    1. 9.1 文档支持
      1. 9.1.1 相关文档
    2. 9.2 Community Resources
    3. 9.3 商标
    4. 9.4 静电放电警告
    5. 9.5 Export Control Notice
    6. 9.6 Glossary
  10. 10机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Energy Detect Control (EDCR)

Table 5-29 Energy Detect Control (EDCR), Address 0x1D

BIT BIT NAME DEFAULT DESCRIPTION
15 ED_EN 0, RW Energy Detect Enable:
Allow Energy Detect Mode.
When Energy Detect is enabled and Auto-Negotiation is disabled via the BMCR register, Auto-MDIX should be disabled via the PHYCR register.
14 ED_AUTO_UP 1, RW Energy Detect Automatic Power Up:
Automatically begin power up sequence when Energy Detect Data Threshold value (EDCR[3:0]) is reached. Alternatively, device could be powered up manually using the ED_MAN bit (ECDR[12]).
13 ED_AUTO_DOWN 1, RW Energy Detect Automatic Power Down:
Automatically begin power down sequence when no energy is detected. Alternatively, device could be powered down using the ED_MAN bit (EDCR[12]).
12 ED_MAN 0, RW/SC Energy Detect Manual Power Up/Down:
Begin power up/down sequence when this bit is asserted. When set, the Energy Detect algorithm will initiate a change of Energy Detect state regardless of threshold (error or data) and timer values. In managed applications, this bit can be set after clearing the Energy Detect interrupt to control the timing of changing the power state.
11 ED_BURST_DIS 0, RW Energy Detect Bust Disable:
Disable bursting of energy detect data pulses. By default, Energy Detect (ED) transmits a burst of 4 ED data pulses each time the CD is powered up. When bursting is disabled, only a single ED data pulse will be send each time the CD is powered up.
10 ED_PWR_STATE 0, RO Energy Detect Power State:
Indicates current Energy Detect Power state. When set, Energy Detect is in the powered up state. When cleared, Energy Detect is in the powered down state. This bit is invalid when Energy Detect is not enabled.
9 ED_ERR_MET 0, RO/COR Energy Detect Error Threshold Met:
No action is automatically taken upon receipt of error events. This bit is informational only and would be cleared on a read.
8 ED_DATA_MET 0, RO/COR Energy Detect Data Threshold Met:
The number of data events that occurred met or surpassed the Energy Detect Data Threshold. This bit is cleared on a read.
7:4 ED_ERR_COUNT 0001, RW Energy Detect Error Threshold:
Threshold to determine the number of energy detect error events that should cause the device to take action. Intended to allow averaging of noise that may be on the line. Counter will reset after approximately 2 seconds without any energy detect data events.
3:0 ED_DATA_COUNT 0001, RW Energy Detect Data Threshold:
Threshold to determine the number of energy detect events that should cause the device to take actions. Intended to allow averaging of noise that may be on the line. Counter will reset after approximately 2 seconds without any energy detect data events.