ZHCSAM3B December   2012  – April 2022 ADS54T01

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Device Comparison
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics
    6. 7.6  Electrical Characteristics
    7. 7.7  Electrical Characteristics
    8. 7.8  Electrical Characteristics
    9. 7.9  Electrical Characteristics
    10. 7.10 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Test Pattern Output
      2. 8.3.2  Clock Inputs
      3. 8.3.3  SNR and Clock Jitter
      4. 8.3.4  Analog Inputs
      5. 8.3.5  Over-Range Indication
      6. 8.3.6  Interleaving Correction
      7. 8.3.7  High-Resolution Output Data
      8. 8.3.8  Low-Resolution Output Data
      9. 8.3.9  Full Speed – 7 Bit
      10. 8.3.10 Decimated Low-Resolution Output Data
      11. 8.3.11 Multi Device Synchronization
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power-Down Modes
      2. 8.4.2 Feedback Mode: Burst Mode
      3. 8.4.3 Receive Mode: Decimation Filter
      4. 8.4.4 Manual Trigger Mode
      5. 8.4.5 Auto Trigger Mode
    5. 8.5 Programming
      1. 8.5.1 Device Initialization
      2. 8.5.2 Serial Register Write
      3. 8.5.3 Serial Register Readout
    6. 8.6 Register Maps
      1. 8.6.1 Serial Register Map
      2. 8.6.2 Description of Serial Interface Registers
  9. Power Supply Recommendations
  10. 10Device and Documentation Support
    1. 10.1 接收文档更新通知
    2. 10.2 支持资源
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 术语表
  11. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Interleaving Correction

The data converter channel consists of two interleaved ADCs each operating at half of the ADC sampling rate but 180° out of phase from each other. The front end track and hold circuitry is operating at the full ADC sampling rate which minimizes the timing mismatch between the two interleaved ADCs. In addition, the ADS54T01 is equipped with internal interleaving correction logic that can be enabled through a SPI register write.

GUID-47FCBB8B-AD39-4ECA-AA95-37B3725A0F9F-low.gifFigure 8-7 Interleaving Correction Block Diagram

The interleaving operation creates 2 distinct and interleaving products:

  • Fs/2 – Fin: this spur is created by gain timing mismatch between the ADCs. Since internally the front end track and hold is operated at the full sampling rate, this component is greatly improved and mostly dependent on gain mismatch.
  • Fs/2 Spur: due to offset mismatch between ADCs
GUID-AA708715-3E33-435F-AFB3-5D4F3EB7DA83-low.gifFigure 8-8 Interleaving Correction Spurs

The auto correction loop can be enabled through a SPI register write in address 0x01. By default, the auto correction function is disabled for lowest possible power consumption. The default settings for the auto correction function should work for most applications. However please contact Texas Instruments if further fine tuning of the algorithm is required.

The auto correction function yields best performance for input frequencies below 250 MHz.