SM320F2812-HT
- High-Performance Static CMOS Technology
- 150 MHz (6.67 ns Cycle Time)
- Low Power (1.8 V Core at 135 MHz, 1.9 V, Core at 150 MHz, 3.3 V I/O) Design
- 3.3 V Flash Voltage
- JTAG Boundary Scan SupportIEEE Standard 1149.1-1990, IEEE Standard Test-Access Port
- High-Performance 32 Bit CPU (TMS320C28x)
- 16 × 16 and 32 x 32 MAC Operations
- 16 × 16 Dual MAC
- Harvard Bus Architecture
- Atomic Operations
- Fast Interrupt Response and Processing
- Unified Memory Programming Model
- 4M Linear Program Address Reach
- 4M Linear Data Address Reach
- Code-Efficient (in C/C++ and Assembly)
- TMS320F24x/LF240x Processor Source Code Compatible
- On-Chip Memory
- Flash Devices: Up to 128K × 16 Flash (Four 8K × 16 and Six 16K × 16 Sectors)
- ROM Devices: Up to 128K × 16 ROM
- 1K × 16 OTP ROM
- L0 and L1: 2 Blocks of 4K × 16 Each Single-Access RAM (SARAM)
- H0: 1 Block of 8K × 16 SARAM
- M0 and M1: 2 Blocks of 1K × 16 Each SARAM
- Boot ROM (4K × 16)
- With Software Boot Modes
- Standard Math Tables
- External Interface
- Up to 1M Total Memory
- Programmable Wait States
- Programmable Read/Write Strobe Timing
- Three Individual Chip Selects
- Clock and System Control
- Dynamic PLL Ratio Changes Supported
- On-Chip Oscillator
- Watchdog Timer Module
- Three External Interrupts
- Peripheral Interrupt Expansion (PIE) Block That Supports 45 Peripheral Interrupts
- 128 Bit Security Key/Lock
- Protects Flash/ROM/OTP and L0/L1 SARAM
- Prevents Firmware Reverse Engineering
- Three 32 Bit CPU Timers
- Motor Control Peripherals
- Two Event Managers (EVA, EVB)
- Compatible to 240xA Devices
- Serial Port Peripherals
- Serial Peripheral Interface (SPI)
- Two Serial Communications Interfaces (SCIs), Standard UART
- Multichannel Buffered Serial Port (McBSP) With SPI Mode
- 12 Bit ADC, 16 Channels
- 2 × 8 Channel Input Multiplexer
- Two Sample-and-Hold
- Single/Simultaneous Conversions
- Fast Conversion Rate: 80 ns/12.5 MSPS
- Up to 56 Individually Programmable, Multiplexed General-Purpose Input / Output (GPIO) Pins
- Advanced Emulation Features
- Analysis and Breakpoint Functions
- Real-Time Debug via Hardware
- Development Tools Include
- ANSI C/C++ Compiler/Assembler/Linker
- Supports TMS320C24x/240x Instructions
- Code Composer Studio IDE
- DSP/BIOS
- JTAG Scan Controllers [Texas Instruments (TI) or Third-Party]
- Evaluation Modules
- Broad Third-Party Digital Motor Control Support
- Low-Power Modes and Power Savings
- IDLE, STANDBY, HALT Modes Supported
- Disable Individual Peripheral Clocks
- APPLICATIONS
- Controlled Baseline
- One Assembly/Test Site
- One Fabrication Site
- Available in Extreme (–55°C/220°C) Temperature Range(1)
- Extended Product Life Cycle
- Extended Product-Change Notification
- Product Traceability
- Texas Instruments high temperature products utilize highly optimized silicon (die)
solutions with design and process enhancements to maximize performance over
extended temperatures.
(1) Custom temperature ranges available
The SM320F2812 device, member of the C28xE DSP generation, is a highly integrated, high-performance solution for demanding control applications. The functional blocks and the memory maps are described in Section 3, Functional Overview.
Throughout this document SM320F2812 is abbreviated as F2812.
技术文档
| 顶层文档 | 类型 | 标题 | 格式选项 | 下载最新的英语版本 | 日期 | |
|---|---|---|---|---|---|---|
| * | 数据表 | Digital Signal Processor. 数据表 (Rev. B) | 2011-6-27 | |||
| * | 勘误表 | SM320F2812-HT AVSSREFBG and AVDDREFBG Die Pad X-Center | PDF | HTML | 2021-11-11 | ||
| * | 辐射与可靠性报告 | SM320F2812HFGS150 Reliability Report | 2012-8-13 |
设计与开发
如需其他信息或资源，请点击以下任一标题进入详情页面查看（如有）。
TMDSEMU200-U — XDS200 USB 调试探针
XDS200 是用于调试 TI 嵌入式器件的调试探针（仿真器）。对于大多数器件，建议使用较新、成本较低的 XDS110 (www.ti.com/tool/TMDSEMU110-U)。XDS200 在单个仓体中支持更广泛的标准（IEEE1149.1、IEEE1149.7、SWD）。所有 XDS 调试探针在所有具有嵌入式跟踪缓冲器 (ETB) 的 Arm® 和 DSP 处理器中均支持内核和系统跟踪。
XDS200 通过 TI 20 引脚连接器（带有适用于 TI 14 引脚、Arm Cortex® 10 引脚和 Arm 20 引脚的多个适配器）连接到目标板，并通过 USB2.0 高速 (...)
TMDSEMU560V2STM-U — XDS560™ 软件 v2 系统跟踪 USB 调试探针
XDS560v2 是 XDS560™ 系列调试探针中性能最高的一款，同时支持传统 JTAG 标准 (IEEE1149.1) 和 cJTAG (IEEE1149.7)。 请注意，它不支持串行线调试 (SWD)。
对于带有嵌入式缓冲跟踪器 (ETB) 的所有 ARM 和 DSP 处理器，所有 XDS 调试探针均支持核心和系统跟踪。 对于引脚上的跟踪，则需要使用 XDS560v2 PRO TRACE。
XDS560v2 通过 MIPI HSPT 60 引脚连接器（带有多个用于 TI 14 引脚、TI 20 引脚和 ARM 20 引脚的适配器）连接到目标板，并通过 USB2.0 高速 (...)
TMDSEMU560V2STM-UE — Spectrum Digital XDS560v2 系统跟踪 USB 和以太网
XDS560v2 System Trace 是 XDS560v2 系列高性能 TI 处理器调试探针（仿真器）的第一种型号。XDS560v2 是 XDS 系列调试探针中性能最高的一款，同时支持传统 JTAG 标准 (IEEE1149.1) 和 cJTAG (IEEE1149.7)。
XDS560v2 System Trace 在其巨大的外部存储器缓冲区中加入了系统引脚跟踪。这种外部存储器缓冲区适用于指定的 TI 器件，通过捕获相关器件级信息，获得准确的总线性能活动和吞吐量，并对内核和外设进行电源管理。此外，对于带有嵌入式缓冲跟踪器 (ETB) 的所有 ARM 和 DSP 处理器，所有 XDS (...)
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash 是 TI 庞大的 CCStudio™ 开发生态系统的成员并且是一款软件工具，用于对 TI 微控制器和无线连接器件上的片上闪存以及 TI 处理器的板载闪存进行编程。UniFlash 提供图形界面和命令行界面，可在桌面上或云中运行。
可以在 CCStudio™ 开发人员专区从云中运行 UniFlash，也可以将其下载并在 Windows®、Linux® 和 macOS® 计算机上使用。
请注意，毫米波、AMx、K2G 和 J7 器件不支持 macOS。AMx、K2G 和 J7 器件仅在命令行上受支持。
| 封装 | 引脚 | CAD 符号、封装和 3D 模型 |
|---|---|---|
| DIESALE (KGD) | — | Ultra Librarian |
| CFP (HFG) | 172 | Ultra Librarian |