主页 接口 I2C、I3C 和 SPI IC I2C 和 SPI 通用 I/O (GPIO)

PCA9554A

正在供货

具有中断、弱上拉和配置寄存器的 8 位 2.3V 至 5.5V I2C/SMBus I/O 扩展器

可提供此产品的更新版本

open-in-new 比较替代产品
功能优于比较器件,可直接替换。
TCA9554A 正在供货 具有中断、弱上拉和配置寄存器的 8 位 1.65V 至 5.5V I2C/SMBus I/O 扩展器 Performance enhancements for power-on reset, interrupt, and lower voltage operation.

产品详情

Number of I/Os 8 Features Configuration registers, Interrupt pin Addresses 8 Rating Catalog Frequency (max) (MHz) 0.4 Operating temperature range (°C) -40 to 85
Number of I/Os 8 Features Configuration registers, Interrupt pin Addresses 8 Rating Catalog Frequency (max) (MHz) 0.4 Operating temperature range (°C) -40 to 85
SOIC (DW) 16 106.09 mm² (10.3 mm × 10.3 mm) SSOP (DBQ) 16 29.4 mm² (4.9 mm × 6 mm) TVSOP (DGV) 16 23.04 mm² (3.6 mm × 6.4 mm) VQFN (RGT) 16 9 mm² (3 mm × 3 mm) SSOP (DB) 16 48.36 mm² (6.2 mm × 7.8 mm) VQFN (RGV) 16 16 mm² (4 mm × 4 mm)
  • I2C 至并行端口扩展器
  • 开漏电路低电平有效中断输出
  • 2.3 V 至 5.5V 的工作电源电压范围
  • 耐受 5V 电压的 I/O
  • 400kHz 快速 I2C 总线
  • 3 个硬件地址引脚可在 I2C/SMBus 上支持最多 8 个器件
  • 输入/输出配置寄存器
  • 极性反转寄存器
  • 内部加电复位
  • 所用通道在加电时被配置为输入
  • 加电时无毛刺脉冲
  • 针对直接驱动 LED 的具有高电流驱动最大能力的锁存输出
  • 锁断性能超过 100mA,符合 JESD 78 II 类规范的要求)
  • ESD 保护性能超过 JESD 22 规范要求
    • 2000V 人体放电模型 (A114-A)
    • 200V 机器放电模型 (A115-A)
    • 1000V 带电器件模型 (C101)
  • I2C 至并行端口扩展器
  • 开漏电路低电平有效中断输出
  • 2.3 V 至 5.5V 的工作电源电压范围
  • 耐受 5V 电压的 I/O
  • 400kHz 快速 I2C 总线
  • 3 个硬件地址引脚可在 I2C/SMBus 上支持最多 8 个器件
  • 输入/输出配置寄存器
  • 极性反转寄存器
  • 内部加电复位
  • 所用通道在加电时被配置为输入
  • 加电时无毛刺脉冲
  • 针对直接驱动 LED 的具有高电流驱动最大能力的锁存输出
  • 锁断性能超过 100mA,符合 JESD 78 II 类规范的要求)
  • ESD 保护性能超过 JESD 22 规范要求
    • 2000V 人体放电模型 (A114-A)
    • 200V 机器放电模型 (A115-A)
    • 1000V 带电器件模型 (C101)

The PCA9554A open-drain interrupt ( INT) output is activated when any input state differs from its corresponding Input Port register state and is used to indicate to the system master that an input state has changed.

INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I2C bus. Thus, the PCA9554A can remain a simple slave device.

The device’s outputs (latched) have high-current drive capability for directly driving LEDs and low current consumption.

Three hardware pins (A0, A1, and A2) are used to program and vary the fixed I2C address and allow up to eight devices to share the same I2C bus or SMBus.

The PCA9554A is pin-to-pin and I2C address compatible with the PCF8574A. However, software changes are required, due to the enhancements in the PCA9554A over the PCF8574A.

The PCA9554A and PCA9554 are identical except for their fixed I2C address. This allows for up to 16 of these devices (8 of each) on the same I2C/SMBus.

The PCA9554A open-drain interrupt ( INT) output is activated when any input state differs from its corresponding Input Port register state and is used to indicate to the system master that an input state has changed.

INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I2C bus. Thus, the PCA9554A can remain a simple slave device.

The device’s outputs (latched) have high-current drive capability for directly driving LEDs and low current consumption.

Three hardware pins (A0, A1, and A2) are used to program and vary the fixed I2C address and allow up to eight devices to share the same I2C bus or SMBus.

The PCA9554A is pin-to-pin and I2C address compatible with the PCF8574A. However, software changes are required, due to the enhancements in the PCA9554A over the PCF8574A.

The PCA9554A and PCA9554 are identical except for their fixed I2C address. This allows for up to 16 of these devices (8 of each) on the same I2C/SMBus.

下载 观看带字幕的视频 视频

技术文档

未找到结果。请清除搜索并重试。
查看全部 7
顶层文档 类型 标题 格式选项 下载最新的英语版本 日期
* 数据表 PCA9554A 具有中断输出和配置寄存器的远程 8 位 I2C 和 SMBus I/O 扩展器 数据表 (Rev. F) PDF | HTML 英语版 (Rev.F) PDF | HTML 2021-6-14
应用手册 Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) PDF | HTML 2024-7-3
应用手册 I2C Dynamic Addressing 2019-4-25
应用手册 Choosing the Correct I2C Device for New Designs PDF | HTML 2016-9-7
应用手册 Understanding the I2C Bus PDF | HTML 2015-6-30
应用手册 Maximum Clock Frequency of I2C Bus Using Repeaters 2015-5-15
应用手册 I2C Bus Pull-Up Resistor Calculation PDF | HTML 2015-2-13

设计与开发

如需其他信息或资源,请点击以下任一标题进入详情页面查看(如有)。

设计工具

I2C-DESIGNER — I2C 设计者工具

利用 I2C 设计器工具,可快速解决基于 I2C 设计中寻址、电压电平和频率方面的冲突。输入主输入端和从输入端,以自动生成 I2C 树活轻松构建自定义解决方案。此工具可在调试缺失确认、选择上拉电阻器和满足 I2C 总线最大容性负载方面提供指导,从而帮助设计人员节省时间并遵循 I2C 标准。 
支持的产品和硬件
封装 引脚 CAD 符号、封装和 3D 模型
SOIC (DW) 16 Ultra Librarian
SSOP (DBQ) 16 Ultra Librarian
TVSOP (DGV) 16 Ultra Librarian
VQFN (RGT) 16 Ultra Librarian
SSOP (DB) 16 Ultra Librarian
VQFN (RGV) 16 Ultra Librarian

订购和质量

推荐产品可能包含与 TI 此产品相关的参数、评估模块或参考设计。

支持和培训

可获得 TI 工程师技术支持的 TI E2E™ 论坛

所有内容均由 TI 和社区贡献者按“原样”提供,并不构成 TI 规范。请参阅使用条款

如果您对质量、包装或订购 TI 产品有疑问,请参阅 TI 支持。​​​​​​​​​​​​​​

视频