返回页首

产品详细信息

参数

Number of channels (#) 1 Total supply voltage (Max) (+5V=5, +/-5V=10) 36 Total supply voltage (Min) (+5V=5, +/-5V=10) 7 Rail-to-rail In to V+ GBW (Typ) (MHz) 2 Slew rate (Typ) (V/us) 3.4 Vos (offset voltage @ 25 C) (Max) (mV) 1.5 Iq per channel (Typ) (mA) 0.29 Vn at 1 kHz (Typ) (nV/rtHz) 40 Rating Military Operating temperature range (C) -55 to 125 Offset drift (Typ) (uV/C) 6 Features Input bias current (Max) (pA) 60 CMRR (Typ) (dB) 90 Output current (Typ) (mA) 45 Architecture FET open-in-new 查找其它 通用 运算放大器

封装|引脚|尺寸

CDIP (JG) 8 - LCCC (FK) 20 - open-in-new 查找其它 通用 运算放大器

特性

  • 2× Bandwidth (2 MHz) of the TL06x and TL03x Operational Amplifiers
  • Low Supply Current ... 290 µA/Ch Typ
  • On-chip Offset Voltage Trimming for Improved DC Performance
  • High Output Drive, Specified into 100- Loads
  • Lower Noise Floor Than Earlier Generations of Low-Power BiFETs
open-in-new 查找其它 通用 运算放大器

描述

The TLE206x series of low-power JFET-input operational amplifiers doubles the bandwidth of the earlier generation TL06x and TL03x BiFET families without significantly increasing power consumption. Texas Instruments Excalibur process also delivers a lower noise floor than the TL06x and TL03x. On-chip zener trimming of offset voltage yields precision grades for dc-coupled applications. The TL206x devices are pin-compatible with other TI BiFETs; they can be used to double the bandwidth of TL06x and TL03x circuits, or to reduce power consumption of TL05x, TL07x, and TL08x circuits by nearly 90%.

BiFET operational amplifiers offer the inherently-higher input impedance of the JFET-input transistors, without sacrificing the output drive associated with bipolar amplifiers. This makes them better suited for interfacing with high-impedance sensors or very low-level ac signals. They also feature inherently better ac response than bipolar or CMOS devices having comparable power consumption. The TLE206x family features a high-output-drive circuit capable of driving 100- loads at supplies as low as ±5 V. This makes them uniquely suited for driving transformer loads in modems and other applications requiring good ac characteristics, low power, and high output drive.

Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to observe common-mode input voltage limits and output swing when operating from a single supply. DC biasing of the input signal is required and loads should be terminated to a virtual ground node at mid-supply. Texas Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from single supplies.

The TLE206x are fully specified at ±15 V and ±5 V. For operation in low-voltage and/or single-supply systems, Texas Instruments LinCMOS families of operational amplifiers (TLC- and TLV-prefixes) are recommended. When moving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidth requirements, and output loading. The Texas Instrument TLV2432 and TLV2442 CMOS operational amplifiers are excellent choices to consider.

open-in-new 查找其它 通用 运算放大器
下载

技术文档

= 特色
未找到结果。请清除搜索,并重试。 查看所有 8
类型 标题 下载最新的英文版本 发布
* 数据表 TLE206xx: Excalibur JFET-Input High-Output-Drive uPower Op Amps 数据表 2004年 5月 5日
技术文章 What is an op amp? 2020年 1月 21日
技术文章 Designing tiny microphone circuits with the industry’s smallest op amp 2018年 4月 12日
技术文章 How to lay out a PCB for high-performance, low-side current-sensing designs 2018年 2月 6日
解决方案指南 The Signal e-book: A compendium of blog posts on op amp design topics. 下载英文版本 2018年 1月 31日
技术文章 Low-side current sensing for high-performance cost-sensitive applications 2018年 1月 22日
SMD TLE2061AM SMD 5962-90807 2016年 6月 21日
应用手册 Errata: TLE206x/TLE206xA/TLE206xB EMI Immunity Performance 2013年 6月 9日

设计与开发

有关其他条款或所需资源,请点击下面的任何链接来查看详情页面。

硬件开发

评估板 下载
document-generic 用户指南
说明

The Universal OPAMPEVM is a series of general purpose blank circuit boards that simplify prototyping circuits for a variety of IC package types. The evaluation module board design allows many different circuits to be constructed easily and quickly. Five models are offered with each targeted for (...)

设计工具和仿真

仿真工具 下载
document-generic 用户指南 document-generic 下载英文版本 (Rev.A)
计算工具 下载
模拟工程师计算器
ANALOG-ENGINEER-CALC — 模拟工程师计算器旨在加快模拟电路设计工程师经常使用的许多重复性计算。该基于 PC 的工具提供图形界面,其中显示各种常见计算的列表(从使用反馈电阻器设置运算放大器增益到为稳定模数转换器 (ADC) 驱动器缓冲器电路选择合适的电路设计元件)。除了可用作单独的工具之外,该计算器还能够很好地与模拟工程师口袋参考书中所述的概念配合使用。
特性
  • 通过模数转换器 (ADC) 和数模转换器 (DAC) 加快电路设计
    • 噪声计算
    • 常见单位转换
  • 解决常见的放大器电路设计问题
    • 使用标准电阻器进行增益选择
    • 滤波器配置
    • 常见放大器配置的总噪声
  • 执行 PCB 寄生计算(例如 R、L 和 C)
  • 查找常见传感器的传感器输出值(例如 RTD、热电偶)
  • 解决常见无源电路问题(例如使用无源组件的分压器)

CAD/CAE 符号

封装 引脚 下载
CDIP (JG) 8 视图选项
LCCC (FK) 20 视图选项

订购与质量

支持与培训

可获得 TI E2E™ 论坛的工程师技术支持

所有内容均由 TI 和社区网友按“原样”提供,并不构成 TI 规范。参阅使用条款

如果您对质量、包装或订购 TI 产品有疑问,请参阅 TI 支持